- 06 Nov, 2022 9 commits
-
-
Krzysztof Kozlowski authored
DT schema expects LPASS pin configuration nodes to be named with '-state' suffix and their optional children with '-pins' suffix. Signed-off-by:
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Reviewed-by:
Neil Armstrong <neil.armstrong@linaro.org> Signed-off-by:
Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20220927153429.55365-3-krzysztof.kozlowski@linaro.org
-
Krzysztof Kozlowski authored
The LPASS pin-controller is not a clock provider: qcom/sc7280-herobrine-herobrine-r1.dtb: pinctrl@33c0000: '#clock-cells' does not match any of the regexes: '-state$', 'pinctrl-[0-9]+' Signed-off-by:
-
Marijn Suijten authored
In addition to PMIC-specific (pm6125) thermistors downstream extends this set with the rf-pa0/rf-pa1, quiet, camera-flash and UFS/eMMC thermistors in sm6125 (trinket) board and seine-specific DT files. All thermistors report sensible temperature readings in userspace. The sensors are also added to their respective Thermal Monitor node, with thermal zones to match where applicable: emmc-ufs and camera-flash are not available on the TM5 block, hence cannot be configured with a tripping point and will not have a thermal zone. Signed-off-by:
Marijn Suijten <marijn.suijten@somainline.org> Reviewed-by:
AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org> Signed-off-by:
-
Marijn Suijten authored
The Sony Xperia Seine board uses the PM6125; include it and configure the PON buttons that provide the power and volume-up key. Signed-off-by:
-
Marijn Suijten authored
This PMIC is commonly used on boards with an SM6125 SoC and looks very similar in layout to the PM6150. Downstream declares more nodes to be available, but these have been omitted from this patch: the pwm/lpg block is unused on my reference device making it impossible to test/validate, and the spmi-clkdiv does not have a single device-tree binding using this driver yet, hence inclusion is better postponed until ie. audio which uses these clocks is brought up. Signed-off-by:
Konrad Dybcio <konrad.dybcio@somainline.org> Signed-off-by:
-
Marijn Suijten authored
The register address in the node name is shadowing vph_pwr@83, whereas the ADC5_VCOIN register resolves to 0x85. Fix this copy-paste discrepancy. Fixes: 4bf09754 ("arm64: dts: qcom: pm660: Add VADC and temp alarm nodes") Signed-off-by:
-
Marijn Suijten authored
Document support for the pm6125, typically paired with the sm6125 SoC. Signed-off-by:
-
Dmitry Baryshkov authored
Change HDMI PHY node name from custom 'hdmi-phy' to the generic 'phy'. Signed-off-by:
Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by:
-
Krzysztof Kozlowski authored
Document Google Cheza board compatibles recently added. Signed-off-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
- 28 Oct, 2022 6 commits
-
-
Iskren Chernev authored
Add initial support for OnePlus Nord N100, based on SM4250. Currently working: - boots - usb - built-in flash storage (UFS) - SD card reader Signed-off-by:
Iskren Chernev <iskren.chernev@gmail.com> Signed-off-by:
-
Iskren Chernev authored
The SM4250 is a downclocked version of the SM6115. Signed-off-by:
-
Iskren Chernev authored
Add support for Qualcomm SM6115 SoC. This includes: - GCC - Pinctrl - RPM (CC+PD) - USB - MMC - UFS Signed-off-by:
-
Iskren Chernev authored
oneplus,billie2 (OnePlus Nord N100) is based on QualComm Snapdragon SM4250 SoC. Add support for the same in dt-bindings. Signed-off-by:
Caleb Connolly <caleb@connolly.tech> Signed-off-by:
-
Johan Hovold authored
Add the TCSR node which is needed for PCIe configuration. Signed-off-by:
Johan Hovold <johan+linaro@kernel.org> Reviewed-by:
-
Nikita Travkin authored
Both a2015 devices use motor drivers controlled with PWM signal. A5 additionally has a fixed regulator that powers the driver and is controlled by enable signal. A3 routes that enable signal to the motor driver itself. To simplify the description, add the motor to the common dtsi and assume a regulator is used for both. Signed-off-by:
Nikita Travkin <nikita@trvn.ru> [Rename the nodes to be reusable in msm8916-sansung-e2015] Signed-off-by:
Lin, Meng-Bo <linmengbo0689@protonmail.com> Signed-off-by:
-
- 20 Oct, 2022 1 commit
-
-
Bryan O'Donoghue authored
The documented yaml compat string for the apq8016 is "qcom,apq8016-lpass-cpu" not "qcom,lpass-cpu-apq8016". Looking at the other lpass compat strings the general form is "qcom,socnum-lpass-cpu". We need to fix both the driver and dts to match. Signed-off-by:
Bryan O'Donoghue <bryan.odonoghue@linaro.org> Signed-off-by:
-
- 18 Oct, 2022 24 commits
-
-
Vladimir Lypak authored
Add the MDSS, MDP and DSI nodes that are found on msm8953 SoC. Signed-off-by:
Vladimir Lypak <vladimir.lypak@gmail.com> Signed-off-by:
Luca Weiss <luca@z3ntu.xyz> Signed-off-by:
-
Vladimir Lypak authored
Add the nodes describing the iommu and its context banks that are found on msm8953 SoCs. Signed-off-by:
-
Caleb Connolly authored
Some devices have been using hsuart0 as an alias for the bluetooth UART, rename this to serial1 Signed-off-by:
-
Dylan Van Assche authored
Add serial1 alias, firmware name and use 4 pin UART pinmux. Signed-off-by:
Dylan Van Assche <me@dylanvanassche.be> Signed-off-by:
-
Caleb Connolly authored
The 4-pin configuration for UART6 is used for all or almost all SDM845 devices with built in Bluetooth. Move the pinmux configuration to sdm845.dtsi in preparation to be removed from individual devices in future patches. Suggested-by:
-
Luca Weiss authored
The bindings require a SoC-specific compatible to be used next to qcom,cpufreq-epss. Add it to make dtbs_check happy. Signed-off-by:
-
Krzysztof Kozlowski authored
DT schema expects TLMM pin configuration nodes to be named with '-state' suffix and their optional children with '-pins' suffix. Signed-off-by:
-
Krzysztof Kozlowski authored
There is no "normal" function, so use "gpio" for backlight button pin configuration. Signed-off-by:
-
Krzysztof Kozlowski authored
Qualcomm pinctrl bindings and drivers expect gpio-ranges property. Signed-off-by:
-
Luca Weiss authored
This ufs_variant node seems to be a remnant from downstream devicetree. As it doesn't seem to be used by anything upstream, remove it from the dtsi. Signed-off-by:
-
Krzysztof Kozlowski authored
DT schema expects TLMM pin configuration nodes to be named with '-state' suffix and their optional children with '-pins' suffix. All nodes for GPIOs must also define the function property. Signed-off-by:
-
Krzysztof Kozlowski authored
The I2C8 pins are split into i2c8_a (GPIO30 and GPIO31) and i2c8_b (GPIO44 and GPIO52). Correct the name of function for I2C8 pins. Signed-off-by:
-
Krzysztof Kozlowski authored
Configure UART1 and UART2 pins to respective functions in default state, otherwise the pins might stay as GPIOs. Signed-off-by:
-
Dmitry Torokhov authored
According to s3fwrn5 driver code the "enable" GPIO line is driven "high" when chip is not in use (mode is S3FWRN5_MODE_COLD), and is driven "low" when chip is in use. s3fwrn5_phy_power_ctrl(): ... gpio_set_value(phy->gpio_en, 1); ... if (mode != S3FWRN5_MODE_COLD) { msleep(S3FWRN5_EN_WAIT_TIME); gpio_set_value(phy->gpio_en, 0); msleep(S3FWRN5_EN_WAIT_TIME); } Therefore the line described by "en-gpios" property should be annotated as "active low". The wakeup gpio appears to have correct polarity (active high). Signed-off-by:Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
-
Krzysztof Kozlowski authored
Compatibles can come in two formats. Either "vendor,ip-soc" or "vendor,soc-ip". Qualcomm bindings were mixing both of usages, so add a DT schema file documenting preferred policy and enforcing it for all new compatibles, except few existing patterns. Signed-off-by:
Bhupesh Sharma <bhupesh.sharma@linaro.org> Reviewed-by:
-
Krzysztof Kozlowski authored
New slimbus DT schema expect only SLIMbus bus nodes to be named "slimbus". In case of Qualcomm SLIMbus NGD, the bus node is what was called "ngd". Signed-off-by:
-
Krzysztof Kozlowski authored
New slimbus DT schema expect only SLIMbus bus nodes to be named "slimbus". In case of Qualcomm SLIMbus NGD, the bus node is what was called "ngd". Signed-off-by:
Steev Klimaszewski <steev@kali.org> Signed-off-by:
-
Krzysztof Kozlowski authored
Bindings document only two DMA channels. Linux driver also does not use remaining rx2/tx2. Signed-off-by:
-
Krzysztof Kozlowski authored
Bindings document only two DMA channels. Linux driver also does not use remaining rx2/tx2. Signed-off-by:
-
Krzysztof Kozlowski authored
Correct slimbus address/size cells to match bindings. Signed-off-by:
-
Krzysztof Kozlowski authored
slimbus uses address-cells=2, so correct children unit addresses. Signed-off-by:
-
Krzysztof Kozlowski authored
Drop undocumented reg-names from slimbus node - there is only one address range and Linux implementation does not use it. Signed-off-by:
-
Krzysztof Kozlowski authored
Drop properties from slimbus node: unneeded status and downstream-related qcom,apps-ch-pipes/qcom,ea-pc (not documented, not used). Signed-off-by:
-
Robert Marko authored
Use "okay" instead of "ok" in USB nodes as "ok" is deprecated. Signed-off-by:
Robert Marko <robimarko@gmail.com> Reviewed-by:
-
