- 02 Feb, 2023 27 commits
-
-
Paolo Abeni authored
Raju Rangoju says: ==================== amd-xgbe: add support for 2.5GbE and rx-adaptation This patch series adds support for 2.GbE in 10GBaseT mode and rx-adaptation support for Yellow Carp devices. 1) Support for 2.5GbE: Add the necessary changes to the driver to fully recognize and enable 2.5GbE speed in 10GBaseT mode. 2) Support for rx-adaptation: In order to support the 10G backplane mode without Auto-negotiation and to support the longer-length DAC cables, it requires PHY to perform RX Adaptation sequence as mentioned in the Synopsys databook. Add the necessary changes to Yellow Carp devices to ensure seamless RX Adaptation for 10G-SFI (LONG DAC), and 10G-KR modes without Auto-Negotiation (CL72 not present) ==================== Link: https://lore.kernel.org/r/20230201054932.212700-1-Raju.Rangoju@amd.comSigned-off-by:
Paolo Abeni <pabeni@redhat.com>
-
Raju Rangoju authored
The existing implementation for non-Autonegotiation 10G speed modes does not enable RX adaptation in the Driver and FW. The RX Equalization settings (AFE settings alone) are manually configured and the existing link-up sequence in the driver does not perform rx adaptation process as mentioned in the Synopsys databook. There's a customer request for 10G backplane mode without Auto-negotiation and for the DAC cables of more significant length that follow the non-Autonegotiation mode. These modes require PHY to perform RX Adaptation. The proposed logic adds the necessary changes to Yellow Carp devices to ensure seamless RX Adaptation for 10G-SFI (LONG DAC) and 10G-KR without AN (CL72 not present). The RX adaptation core algorithm is executed by firmware, however, to achieve that a new mailbox sub-command is required to be sent by the driver. Co-developed-by:
Shyam Sundar S K <Shyam-sundar.S-k@amd.com> Signed-off-by:
Raju Rangoju <Raju.Rangoju@amd.com> Signed-off-by:
-
Raju Rangoju authored
Add support to the driver to fully recognize and enable 2.5GbE speed in 10GBaseT mode. Acked-by:
-
Paolo Abeni authored
Pedro Tammela says: ==================== net/sched: transition act_pedit to rcu and percpu stats The software pedit action didn't get the same love as some of the other actions and it's still using spinlocks and shared stats. Therefore, transition the action to rcu and percpu stats which improves the action's performance. We test this change with a very simple packet forwarding setup: tc filter add dev ens2f0 ingress protocol ip matchall \ action pedit ex munge eth src set b8:ce:f6:4b:68:35 pipe \ action pedit ex munge eth dst set ac:1f:6b:e4:ff:93 pipe \ action mirred egress redirect dev ens2f1 tc filter add dev ens2f1 ingress protocol ip matchall \ action pedit ex munge eth src set b8:ce:f6:4b:68:34 pipe \ action pedit ex munge eth dst set ac:1f:6b:e4:ff:92 pipe \ action mirred egress redirect dev ens2f0 Using TRex with a http-like profile, in our setup with a 25G NIC and a 26 cores Intel CPU, we observe the following in perf: before: 11.59% 2.30% [kernel] [k] tcf_pedit_act 2.55% tcf_pedit_act 8.38% _raw_spin_lock 6.43% native_queued_spin_lock_slowpath after: 1.46% 1.46% [kernel] [k] tcf_pedit_act tdc results for pedit after the patch: 1..69 ok 1 319a - Add pedit action that mangles IP TTL ok 2 7e67 - Replace pedit action with invalid goto chain ok 3 377e - Add pedit action with RAW_OP offset u32 ok 4 a0ca - Add pedit action with RAW_OP offset u32 (INVALID) ok 5 dd8a - Add pedit action with RAW_OP offset u16 u16 ok 6 53db - Add pedit action with RAW_OP offset u16 (INVALID) ok 7 5c7e - Add pedit action with RAW_OP offset u8 add value ok 8 2893 - Add pedit action with RAW_OP offset u8 quad ok 9 3a07 - Add pedit action with RAW_OP offset u8-u16-u8 ok 10 ab0f - Add pedit action with RAW_OP offset u16-u8-u8 ok 11 9d12 - Add pedit action with RAW_OP offset u32 set u16 clear u8 invert ok 12 ebfa - Add pedit action with RAW_OP offset overflow u32 (INVALID) ok 13 f512 - Add pedit action with RAW_OP offset u16 at offmask shift set ok 14 c2cb - Add pedit action with RAW_OP offset u32 retain value ok 15 1762 - Add pedit action with RAW_OP offset u8 clear value ok 16 bcee - Add pedit action with RAW_OP offset u8 retain value ok 17 e89f - Add pedit action with RAW_OP offset u16 retain value ok 18 c282 - Add pedit action with RAW_OP offset u32 clear value ok 19 c422 - Add pedit action with RAW_OP offset u16 invert value ok 20 d3d3 - Add pedit action with RAW_OP offset u32 invert value ok 21 57e5 - Add pedit action with RAW_OP offset u8 preserve value ok 22 99e0 - Add pedit action with RAW_OP offset u16 preserve value ok 23 1892 - Add pedit action with RAW_OP offset u32 preserve value ok 24 4b60 - Add pedit action with RAW_OP negative offset u16/u32 set value ok 25 a5a7 - Add pedit action with LAYERED_OP eth set src ok 26 86d4 - Add pedit action with LAYERED_OP eth set src & dst ok 27 f8a9 - Add pedit action with LAYERED_OP eth set dst ok 28 c715 - Add pedit action with LAYERED_OP eth set src (INVALID) ok 29 8131 - Add pedit action with LAYERED_OP eth set dst (INVALID) ok 30 ba22 - Add pedit action with LAYERED_OP eth type set/clear sequence ok 31 dec4 - Add pedit action with LAYERED_OP eth set type (INVALID) ok 32 ab06 - Add pedit action with LAYERED_OP eth add type ok 33 918d - Add pedit action with LAYERED_OP eth invert src ok 34 a8d4 - Add pedit action with LAYERED_OP eth invert dst ok 35 ee13 - Add pedit action with LAYERED_OP eth invert type ok 36 7588 - Add pedit action with LAYERED_OP ip set src ok 37 0fa7 - Add pedit action with LAYERED_OP ip set dst ok 38 5810 - Add pedit action with LAYERED_OP ip set src & dst ok 39 1092 - Add pedit action with LAYERED_OP ip set ihl & dsfield ok 40 02d8 - Add pedit action with LAYERED_OP ip set ttl & protocol ok 41 3e2d - Add pedit action with LAYERED_OP ip set ttl (INVALID) ok 42 31ae - Add pedit action with LAYERED_OP ip ttl clear/set ok 43 486f - Add pedit action with LAYERED_OP ip set duplicate fields ok 44 e790 - Add pedit action with LAYERED_OP ip set ce, df, mf, firstfrag, nofrag fields ok 45 cc8a - Add pedit action with LAYERED_OP ip set tos ok 46 7a17 - Add pedit action with LAYERED_OP ip set precedence ok 47 c3b6 - Add pedit action with LAYERED_OP ip add tos ok 48 43d3 - Add pedit action with LAYERED_OP ip add precedence ok 49 438e - Add pedit action with LAYERED_OP ip clear tos ok 50 6b1b - Add pedit action with LAYERED_OP ip clear precedence ok 51 824a - Add pedit action with LAYERED_OP ip invert tos ok 52 106f - Add pedit action with LAYERED_OP ip invert precedence ok 53 6829 - Add pedit action with LAYERED_OP beyond ip set dport & sport ok 54 afd8 - Add pedit action with LAYERED_OP beyond ip set icmp_type & icmp_code ok 55 3143 - Add pedit action with LAYERED_OP beyond ip set dport (INVALID) ok 56 815c - Add pedit action with LAYERED_OP ip6 set src ok 57 4dae - Add pedit action with LAYERED_OP ip6 set dst ok 58 fc1f - Add pedit action with LAYERED_OP ip6 set src & dst ok 59 6d34 - Add pedit action with LAYERED_OP ip6 dst retain value (INVALID) ok 60 94bb - Add pedit action with LAYERED_OP ip6 traffic_class ok 61 6f5e - Add pedit action with LAYERED_OP ip6 flow_lbl ok 62 6795 - Add pedit action with LAYERED_OP ip6 set payload_len, nexthdr, hoplimit ok 63 1442 - Add pedit action with LAYERED_OP tcp set dport & sport ok 64 b7ac - Add pedit action with LAYERED_OP tcp sport set (INVALID) ok 65 cfcc - Add pedit action with LAYERED_OP tcp flags set ok 66 3bc4 - Add pedit action with LAYERED_OP tcp set dport, sport & flags fields ok 67 f1c8 - Add pedit action with LAYERED_OP udp set dport & sport ok 68 d784 - Add pedit action with mixed RAW/LAYERED_OP #1 ok 69 70ca - Add pedit action with mixed RAW/LAYERED_OP #2 ==================== Link: https://lore.kernel.org/r/20230131190512.3805897-1-pctammela@mojatatu.comSigned-off-by: -
Pedro Tammela authored
Remove the check for a negative number of keys as this cannot ever happen Reviewed-by:
Jamal Hadi Salim <jhs@mojatatu.com> Reviewed-by:
Simon Horman <simon.horman@corigine.com> Signed-off-by:
Pedro Tammela <pctammela@mojatatu.com> Signed-off-by:
-
Pedro Tammela authored
The software pedit action didn't get the same love as some of the other actions and it's still using spinlocks and shared stats in the datapath. Transition the action to rcu and percpu stats as this improves the action's performance dramatically on multiple cpu deployments. Reviewed-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fsPaolo Abeni authored
David Howells says: ==================== Here's the fifth part of patches in the process of moving rxrpc from doing a lot of its stuff in softirq context to doing it in an I/O thread in process context and thereby making it easier to support a larger SACK table. The full description is in the description for the first part[1] which is now upstream. The second and third parts are also upstream[2]. A subset of the original fourth part[3] got applied as a fix for a race[4]. The fifth part includes some cleanups: (1) Miscellaneous trace header cleanups: fix a trace string, display the security index in rx_packet rather than displaying the type twice, remove some whitespace to make checkpatch happier and remove some excess tabulation. (2) Convert ->recvmsg_lock to a spinlock as it's only ever locked exclusively. (3) Make ->ackr_window and ->ackr_nr_unacked non-atomic as they're only used in the I/O thread. (4) Don't use call->tx_lock to access ->tx_buffer as that is only accessed inside the I/O thread. sendmsg() loads onto ->tx_sendmsg and the I/O thread decants from that to the buffer. (5) Remove local->defrag_sem as DATA packets are transmitted serially by the I/O thread. (6) Remove the service connection bundle is it was only used for its channel_lock - which has now gone. And some more significant changes: (7) Add a debugging option to allow a delay to be injected into packet reception to help investigate the behaviour over longer links than just a few cm. (8) Generate occasional PING ACKs to probe for RTT information during a receive heavy call. (9) Simplify the SACK table maintenance and ACK generation. Now that both parts are done in the same thread, there's no possibility of a race and no need to try and be cunning to avoid taking a BH spinlock whilst copying the SACK table (which in the future will be up to 2K) and no need to rotate the copy to fit the ACK packet table. (10) Use SKB_CONSUMED when freeing received DATA packets (stop dropwatch complaining). * tag 'rxrpc-next-20230131' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs: rxrpc: Kill service bundle rxrpc: Change rx_packet tracepoint to display securityIndex not type twice rxrpc: Show consumed and freed packets as non-dropped in dropwatch rxrpc: Remove local->defrag_sem rxrpc: Don't lock call->tx_lock to access call->tx_buffer rxrpc: Simplify ACK handling rxrpc: De-atomic call->ackr_window and call->ackr_nr_unacked rxrpc: Generate extra pings for RTT during heavy-receive call rxrpc: Allow a delay to be injected into packet reception rxrpc: Convert call->recvmsg_lock to a spinlock rxrpc: Shrink the tabulation in the rxrpc trace header a bit rxrpc: Remove whitespace before ')' in trace header rxrpc: Fix trace string ==================== Link: https://lore.kernel.org/all/20230131171227.3912130-1-dhowells@redhat.com/Signed-off-by: -
Sunil Goutham authored
NPC exact match feature is supported only on one silicon variant, removed debug messages which print that this feature is not available on all other silicon variants. Signed-off-by:
Sunil Goutham <sgoutham@marvell.com> Signed-off-by:
Ratheesh Kannoth <rkannoth@marvell.com> Reviewed-by:
Leon Romanovsky <leonro@nvidia.com> Link: https://lore.kernel.org/r/20230201040301.1034843-1-rkannoth@marvell.comSigned-off-by:
Jakub Kicinski <kuba@kernel.org>
-
Heng Qi authored
When the single-buffer xdp is loaded and after xdp_linearize_page() is called, *num_buf becomes 0 and (*num_buf - 1) may overflow into a large integer in virtnet_build_xdp_buff_mrg(), resulting in unexpected packet dropping. Fixes: ef75cb51 ("virtio-net: build xdp_buff with multi buffers") Signed-off-by:
Heng Qi <hengqi@linux.alibaba.com> Reviewed-by:
Xuan Zhuo <xuanzhuo@linux.alibaba.com> Signed-off-by:
Michael S. Tsirkin <mst@redhat.com> Link: https://lore.kernel.org/r/20230131085004.98687-1-hengqi@linux.alibaba.comSigned-off-by:
-
Leon Romanovsky authored
In netdev common pattern, extack pointer is forwarded to the drivers to be filled with error message. However, the caller can easily overwrite the filled message. Instead of adding multiple "if (!extack->_msg)" checks before any NL_SET_ERR_MSG() call, which appears after call to the driver, let's add new macro to common code. [1] https://lore.kernel.org/all/Y9Irgrgf3uxOjwUm@unrealReviewed-by:
Nikolay Aleksandrov <razor@blackwall.org> Signed-off-by:
-
Brian Haley authored
When set to zero, the neighbor sysctl proxy_delay value does not cause an immediate reply for ARP/ND requests as expected, it instead causes a random delay between [0, U32_MAX). Looking at this comment from __get_random_u32_below() explains the reason: /* * This function is technically undefined for ceil == 0, and in fact * for the non-underscored constant version in the header, we build bug * on that. But for the non-constant case, it's convenient to have that * evaluate to being a straight call to get_random_u32(), so that * get_random_u32_inclusive() can work over its whole range without * undefined behavior. */ Added helper function that does not call get_random_u32_below() if proxy_delay is zero and just uses the current value of jiffies instead, causing pneigh_enqueue() to respond immediately. Also added definition of proxy_delay to ip-sysctl.txt since it was missing. Signed-off-by:
Brian Haley <haleyb.dev@gmail.com> Link: https://lore.kernel.org/r/20230130171428.367111-1-haleyb.dev@gmail.comSigned-off-by:
-
Jakub Kicinski authored
Xin Long says: ==================== net: support ipv4 big tcp This is similar to the BIG TCP patchset added by Eric for IPv6: https://lwn.net/Articles/895398/ Different from IPv6, IPv4 tot_len is 16-bit long only, and IPv4 header doesn't have exthdrs(options) for the BIG TCP packets' length. To make it simple, as David and Paolo suggested, we set IPv4 tot_len to 0 to indicate this might be a BIG TCP packet and use skb->len as the real IPv4 total length. This will work safely, as all BIG TCP packets are GSO/GRO packets and processed on the same host as they were created; There is no padding in GSO/GRO packets, and skb->len - network_offset is exactly the IPv4 packet total length; Also, before implementing the feature, all those places that may get iph tot_len from BIG TCP packets are taken care with some new APIs: Patch 1 adds some APIs for iph tot_len setting and getting, which are used in all these places where IPv4 BIG TCP packets may reach in Patch 2-7, Patch 8 adds a GSO_TCP tp_status for af_packet users, and Patch 9 add new netlink attributes to make IPv4 BIG TCP independent from IPv6 BIG TCP on configuration, and Patch 10 implements this feature. Note that the similar change as in Patch 2-6 are also needed for IPv6 BIG TCP packets, and will be addressed in another patchset. The similar performance test is done for IPv4 BIG TCP with 25Gbit NIC and 1.5K MTU: No BIG TCP: for i in {1..10}; do netperf -t TCP_RR -H 192.168.100.1 -- -r80000,80000 -O MIN_LATENCY,P90_LATENCY,P99_LATENCY,THROUGHPUT|tail -1; done 168 322 337 3776.49 143 236 277 4654.67 128 258 288 4772.83 171 229 278 4645.77 175 228 243 4678.93 149 239 279 4599.86 164 234 268 4606.94 155 276 289 4235.82 180 255 268 4418.95 168 241 249 4417.82 Enable BIG TCP: ip link set dev ens1f0np0 gro_ipv4_max_size 128000 gso_ipv4_max_size 128000 for i in {1..10}; do netperf -t TCP_RR -H 192.168.100.1 -- -r80000,80000 -O MIN_LATENCY,P90_LATENCY,P99_LATENCY,THROUGHPUT|tail -1; done 161 241 252 4821.73 174 205 217 5098.28 167 208 220 5001.43 164 228 249 4883.98 150 233 249 4914.90 180 233 244 4819.66 154 208 219 5004.92 157 209 247 4999.78 160 218 246 4842.31 174 206 217 5080.99 Thanks for the feedback from Eric and David Ahern. ==================== Link: https://lore.kernel.org/r/cover.1674921359.git.lucien.xin@gmail.comSigned-off-by:
-
Xin Long authored
Similar to Eric's IPv6 BIG TCP, this patch is to enable IPv4 BIG TCP. Firstly, allow sk->sk_gso_max_size to be set to a value greater than GSO_LEGACY_MAX_SIZE by not trimming gso_max_size in sk_trim_gso_size() for IPv4 TCP sockets. Then on TX path, set IP header tot_len to 0 when skb->len > IP_MAX_MTU in __ip_local_out() to allow to send BIG TCP packets, and this implies that skb->len is the length of a IPv4 packet; On RX path, use skb->len as the length of the IPv4 packet when the IP header tot_len is 0 and skb->len > IP_MAX_MTU in ip_rcv_core(). As the API iph_set_totlen() and skb_ip_totlen() are used in __ip_local_out() and ip_rcv_core(), we only need to update these APIs. Also in GRO receive, add the check for ETH_P_IP/IPPROTO_TCP, and allows the merged packet size >= GRO_LEGACY_MAX_SIZE in skb_gro_receive(). In GRO complete, set IP header tot_len to 0 when the merged packet size greater than IP_MAX_MTU in iph_set_totlen() so that it can be processed on RX path. Note that by checking skb_is_gso_tcp() in API iph_totlen(), it makes this implementation safe to use iph->len == 0 indicates IPv4 BIG TCP packets. Signed-off-by:
Xin Long <lucien.xin@gmail.com> Reviewed-by:
David Ahern <dsahern@kernel.org> Reviewed-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
-
Xin Long authored
This patch introduces gso_ipv4_max_size and gro_ipv4_max_size per device and adds netlink attributes for them, so that IPV4 BIG TCP can be guarded by a separate tunable in the next patch. To not break the old application using "gso/gro_max_size" for IPv4 GSO packets, this patch updates "gso/gro_ipv4_max_size" in netif_set_gso/gro_max_size() if the new size isn't greater than GSO_LEGACY_MAX_SIZE, so that nothing will change even if userspace doesn't realize the new netlink attributes. Signed-off-by:
-
Xin Long authored
Introduce TP_STATUS_GSO_TCP tp_status flag to tell the af_packet user that this is a TCP GSO packet. When parsing IPv4 BIG TCP packets in tcpdump/libpcap, it can use tp_len as the IPv4 packet len when this flag is set, as iph tot_len is set to 0 for IPv4 BIG TCP packets. Signed-off-by:
-
Xin Long authored
ipvlan devices calls netif_inherit_tso_max() to get the tso_max_size/segs from the lower device, so when lower device supports BIG TCP, the ipvlan devices support it too. We also should consider its iph tot_len accessing. Signed-off-by:
-
Xin Long authored
It may process IPv4 TCP GSO packets in cipso_v4_skbuff_setattr(), so the iph->tot_len update should use iph_set_totlen(). Note that for these non GSO packets, the new iph tot_len with extra iph option len added may become greater than 65535, the old process will cast it and set iph->tot_len to it, which is a bug. In theory, iph options shouldn't be added for these big packets in here, a fix may be needed here in the future. For now this patch is only to set iph->tot_len to 0 when it happens. Signed-off-by:
-
Xin Long authored
There are also quite some places in netfilter that may process IPv4 TCP GSO packets, we need to replace them too. In length_mt(), we have to use u_int32_t/int to accept skb_ip_totlen() return value, otherwise it may overflow and mismatch. This change will also help us add selftest for IPv4 BIG TCP in the following patch. Note that we don't need to replace the one in tcpmss_tg4(), as it will return if there is data after tcphdr in tcpmss_mangle_packet(). The same in mangle_contents() in nf_nat_helper.c, it returns false when skb->len + extra > 65535 in enlarge_skb(). Signed-off-by:
-
Xin Long authored
There are 1 action and 1 qdisc that may process IPv4 TCP GSO packets and access iph->tot_len, replace them with skb_ip_totlen() and iph_totlen() accordingly. Note that we don't need to replace the one in tcf_csum_ipv4(), as it will return for TCP GSO packets in tcf_csum_ipv4_tcp(). Signed-off-by:
-
Xin Long authored
IPv4 GSO packets may get processed in ovs_skb_network_trim(), and we need to use skb_ip_totlen() to get iph totlen. Signed-off-by:
Aaron Conole <aconole@redhat.com> Reviewed-by:
-
Xin Long authored
These 3 places in bridge netfilter are called on RX path after GRO and IPv4 TCP GSO packets may come through, so replace iph tot_len accessing with skb_ip_totlen() in there. Signed-off-by:
-
Xin Long authored
This patch adds three APIs to replace the iph->tot_len setting and getting in all places where IPv4 BIG TCP packets may reach, they will be used in the following patches. Note that iph_totlen() will be used when iph is not in linear data of the skb. Signed-off-by:
-
Jakub Kicinski authored
Laurent Vivier says: ==================== virtio_net: vdpa: update MAC address when it is generated by virtio-net When the MAC address is not provided by the vdpa device virtio_net driver assigns a random one without notifying the device. The consequence, in the case of mlx5_vdpa, is the internal routing tables of the device are not updated and this can block the communication between two namespaces. To fix this problem, use virtnet_send_command(VIRTIO_NET_CTRL_MAC) to set the address from virtnet_probe() when the MAC address is not provided by the device. ==================== Link: https://lore.kernel.org/r/20230127204500.51930-1-lvivier@redhat.comSigned-off-by:
-
Laurent Vivier authored
In virtnet_probe(), if the device doesn't provide a MAC address the driver assigns a random one. As we modify the MAC address we need to notify the device to allow it to update all the related information. The problem can be seen with vDPA and mlx5_vdpa driver as it doesn't assign a MAC address by default. The virtio_net device uses a random MAC address (we can see it with "ip link"), but we can't ping a net namespace from another one using the virtio-vdpa device because the new MAC address has not been provided to the hardware: RX packets are dropped since they don't go through the receive filters, TX packets go through unaffected. Signed-off-by:
Laurent Vivier <lvivier@redhat.com> Acked-by:
-
Laurent Vivier authored
failover relies on the MAC address to pair the primary and the standby devices: "[...] the hypervisor needs to enable VIRTIO_NET_F_STANDBY feature on the virtio-net interface and assign the same MAC address to both virtio-net and VF interfaces." Documentation/networking/net_failover.rst This patch disables the STANDBY feature if the MAC address is not provided by the hypervisor. Signed-off-by:
-
Huayu Chen authored
This patch corrects two oversights relating to releasing resources and DCB initialisation. 1. If mapping of the dcbcfg_tbl area fails: an error should be propagated, allowing partial initialisation (probe) to be unwound. 2. Conversely, if where dcbcfg_tbl is successfully mapped: it should be unmapped in nfp_nic_dcb_clean() which is called via various error cleanup paths, and shutdown or removal of the PCIE device. Fixes: 9b7fe804 ("nfp: add DCB IEEE support") Signed-off-by:
Huayu Chen <huayu.chen@corigine.com> Reviewed-by:
Niklas Söderlund <niklas.soderlund@corigine.com> Signed-off-by:
-
Jiapeng Chong authored
Swap is a function interface that provides exchange function. To avoid code duplication, we can use swap function. ./net/ipv6/icmp.c:344:25-26: WARNING opportunity for swap(). Reported-by:
Abaci Robot <abaci@linux.alibaba.com> Link: https://bugzilla.openanolis.cn/show_bug.cgi?id=3896Signed-off-by:
Jiapeng Chong <jiapeng.chong@linux.alibaba.com> Reviewed-by:
-
- 01 Feb, 2023 13 commits
-
-
Jakub Kicinski authored
Jiri Pirko says: ==================== devlink: trivial names cleanup This is a follow-up to Jakub's devlink code split and dump iteration helper patchset. No functional changes, just couple of renames to makes things consistent and perhaps easier to follow. ==================== Link: https://lore.kernel.org/r/20230131090613.2131740-1-jiri@resnulli.usSigned-off-by:
-
Jiri Pirko authored
In order to maintain naming consistency, rename and reorder all usages of struct struct devlink_cmd in the following way: 1) Remove "gen" and replace it with "cmd" to match the struct name 2) Order devl_cmds[] and the header file to match the order of enum devlink_command 3) Move devl_cmd_rate_get among the peers 4) Remove "inst" for DEVLINK_CMD_GET 5) Add "_get" suffix to all to match DEVLINK_CMD_*_GET (only rate had it done correctly) Signed-off-by:
Jiri Pirko <jiri@nvidia.com> Reviewed-by:
Jacob Keller <jacob.e.keller@intel.com> Signed-off-by:
-
Jiri Pirko authored
No need to have "gen" inside name of the structure for devlink commands. Remove it. Signed-off-by:
-
Jiri Pirko authored
To have the name of the function consistent with the struct cb name, rename devlink_nl_instance_iter_dump() to devlink_nl_instance_iter_dumpit(). Signed-off-by:
-
Jakub Kicinski authored
Alex Elder says: ==================== net: ipa: remaining IPA v5.0 support This series includes almost all remaining IPA code changes required to support IPA v5.0. IPA register definitions and configuration data for IPA v5.0 will be sent later (soon). Note that the GSI register definitions still require work. GSI for IPA v5.0 supports up to 256 (rather than 32) channels, and this changes the way GSI register offsets are calculated. A few GSI register fields also change. The first patch in this series increases the number of IPA endpoints supported by the driver, from 32 to 36. The next updates the width of the destination field for the IP_PACKET_INIT immediate command so it can represent up to 256 endpoints rather than just 32. The next adds a few definitions of some IPA registers and fields that are first available in IPA v5.0. The next two patches update the code that handles router and filter table caches. Previously these were referred to as "hashed" tables, and the IPv4 and IPv6 tables are now combined into one "unified" table. The sixth and seventh patches add support for a new pulse generator, which allows time periods to be specified with a wider range of clock resolution. And the last patch just defines two new memory regions that were not previously used. ==================== Link: https://lore.kernel.org/r/20230130210158.4126129-1-elder@linaro.orgSigned-off-by:
-
Alex Elder authored
IPA v5.0 uses two memory regions not previously used. Define them and treat them as valid only for IPA v5.0. Signed-off-by:
Alex Elder <elder@linaro.org> Reviewed-by:
-
Alex Elder authored
The AP has third pulse generator available starting with IPA v5.0. Redefine ipa_qtime_val() to support that possibility. Pass the IPA pointer as an argument so the version can be determined. And stop using the sign of the returned tick count to indicate which of two pulse generators to use. Instead, have the caller provide the address of a variable that will hold the selected pulse generator for the Qtime value. And for version 5.0, check whether the third pulse generator best represents the time period. Add code in ipa_qtime_config() to configure the fourth pulse generator for IPA v5.0+; in that case configure both the third and fourth pulse generators to use 10 msec granularity. Consistently use "ticks" for local variables that represent a tick count. Signed-off-by:
-
Alex Elder authored
Starting with IPA v5.0, the head-of-line blocking timer has more than two pulse generators available to define timer granularity. To prepare for that, change the way the field value is encoded to use ipa_reg_encode() rather than ipa_reg_bit(). The aggregation granularity selection could (in principle) also use an additional pulse generator starting with IPA v5.0. Encode the AGGR_GRAN_SEL field differently to allow that as well. Signed-off-by:
-
Alex Elder authored
IPA v5.0+ separates the configuration of entries in the cached (previously "hashed") routing and filtering tables into distinct registers. Previously a single "filter and router" register updated entries in both tables at once; now the routing and filter table caches have separate registers that define their content. This patch updates the code that zeroes entries in the cached filter and router tables to support IPA versions including v5.0+. Signed-off-by:
-
Alex Elder authored
Update the code that causes filter and router table caches to be flushed so that it supports IPA versions 5.0+. It adds a comment in ipa_hardware_config_hashing() that explains that cacheing does not need to be enabled, just as before, because it's enabled by default. (For the record, the FILT_ROUT_CACHE_CFG register would have been used if we wanted to explicitly enable these.) Signed-off-by:
-
Alex Elder authored
Define some new registers that appear starting with IPA v5.0, along with enumerated types identifying their fields. Code that uses these will be added by upcoming patches. Most of the new registers are related to filter and routing tables, and in particular, their "hashed" variant. These tables are better described as "cached", where a hash value determines which entries are cached. From now on, naming related to this functionality will use "cache" instead of "hash", and that is reflected in these new register names. Some registers for managing these caches and their contents have changed as well. A few other new field definitions for registers (unrelated to table caches) are also defined. Signed-off-by:
-
Alex Elder authored
The IP_PACKET_INIT immediate command defines the destination endpoint to which a packet should be sent. Prior to IPA v5.0, a 5 bit field in that command represents the endpoint, but starting with IPA v5.0, the field is extended to 8 bits to support more than 32 endpoints. Signed-off-by:
-
Alex Elder authored
Increase the number of endpoints supported by the driver to 36, which IPA v5.0 supports. This makes it impossible to check at build time whether the supported number is too big to fit within the (5-bit) PACKET_INIT destination endpoint field. Instead, convert the build time check to compare against what fits in 8 bits. Add a check in ipa_endpoint_config() to also ensure the hardware reports an endpoint count that's in the expected range. Just open-code 32 as the limit (the PACKET_INIT field mask is not available where we'd want to use it). Signed-off-by:
-
