- 22 Jun, 2012 35 commits
-
-
Alan Cox authored
commit 1aa3c63c upstream. The low level helper returns 1 on success. The ioctl should however return 0. As this is the only user of the helper return, make the helper return 0 or an error code. Resolves-bug: https://bugzilla.kernel.org/show_bug.cgi?id=43009Signed-off-by:
Alan Cox <alan@linux.intel.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Bjørn Mork authored
commit c41444cc upstream. Some additional IDs found in the BSD/GPL licensed out-of-tree GobiSerial driver from Sierra Wireless. Signed-off-by:
Bjørn Mork <bjorn@mork.no> Signed-off-by:
-
Tony Zelenoff authored
commit b9c87663 upstream. The __devinitconst section can't be referenced from usb_serial_device structure. Thus removed it as it done in other mos* device drivers. Error itself: WARNING: drivers/usb/serial/mos7840.o(.data+0x8): Section mismatch in reference from the variable moschip7840_4port_device to the variable .devinit.rodata:id_table The variable moschip7840_4port_device references the variable __devinitconst id_table [v2] no attach now Signed-off-by:
Tony Zelenoff <antonz@parallels.com> Signed-off-by:
-
Hans de Goede authored
commit afff07e6 upstream. This device gives a bogus answer to get_capacity(16): [ 8628.278614] scsi 8:0:0:0: Direct-Access USB 2.0 USB Flash Drive 1100 PQ: 0 ANSI: 4 [ 8628.279452] sd 8:0:0:0: Attached scsi generic sg4 type 0 [ 8628.280338] sd 8:0:0:0: [sdd] 35747322042253313 512-byte logical blocks: (18.3 EB/15.8 EiB) So set the quirk flag to avoid using get_capacity(16) with it: [11731.386014] usb-storage 2-1.6:1.0: Quirks match for vid 090c pid 1000: 80000 [11731.386075] scsi9 : usb-storage 2-1.6:1.0 [11731.386172] usbcore: registered new interface driver usb-storage [11731.386175] USB Mass Storage support registered. [11732.387394] scsi 9:0:0:0: Direct-Access USB 2.0 USB Flash Drive 1100 PQ: 0 ANSI: 4 [11732.388462] sd 9:0:0:0: Attached scsi generic sg3 type 0 [11732.389432] sd 9:0:0:0: [sdc] 7975296 512-byte logical blocks: (4.08 GB/3.80 GiB) Which makes the capacity look a lot more sane :) Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Tested-by:
Simon Raffeiner <sturmflut@lieberbiber.de> Signed-off-by:
-
Andiry Xu authored
commit 622eb783 upstream. When system software decides to power down the xHC with the intent of resuming operation at a later time, it will ask xHC to save the internal state and restore it when resume to correctly recover from a power event. Two bits are used to enable this operation: Save State and Restore State. xHCI spec 4.23.2 says software should "Set the Controller Save/Restore State flag in the USBCMD register and wait for the Save/Restore State Status flag in the USBSTS register to transition to '0'". However, it does not define how long software should wait for the SSS/RSS bit to transition to 0. Currently the timeout is set to 1ms. There is bug report (https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1002697) indicates that the timeout is too short for ASMedia ASM1042 host controller to save/restore the state successfully. Increase the timeout to 10ms helps to resolve the issue. This patch should be backported to stable kernels as old as 2.6.37, that contain the commit 5535b1d5 "USB: xHCI: PCI power management implementation" Signed-off-by:
Andiry Xu <andiry.xu@gmail.com> Signed-off-by:
Sarah Sharp <sarah.a.sharp@linux.intel.com> Cc: Ming Lei <ming.lei@canonical.com> Signed-off-by:
-
Takashi Iwai authored
commit 32f1d2c5 upstream. This patch fixes a few issues introduced in the recent fix [f8a9e72d: USB: fix resource leak in xhci power loss path] - The endpoints listed in bw table are just links and each entry is an array member of dev->eps[]. But the commit above adds a kfree() call to these instances, and thus it results in memory corruption. - It clears only the first entry of rh_bw[], but there can be multiple ports. - It'd be safer to clear the list_head of ep as well, not only removing from the list, as it's checked in xhci_discover_or_reset_device(). This patch should be backported to kernels as old as 3.2, that contain the commit 839c817c "xhci: Store information about roothubs and TTs." Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
Oliver Neukum <oneukum@suse.de> Signed-off-by:
-
Takashi Iwai authored
commit 46ed8f00 upstream. xhci_free_tt_info() may access the invalid memory when it removes the last entry but the list is not empty. Then tt_next reaches to the list head but it still tries to check the tt_info of that entry. This patch fixes the bug and cleans up the messy code by rewriting with a simple list_for_each_entry_safe(). This patch should be backported to kernels as old as 3.2, that contain the commit 839c817c "xhci: Store information about roothubs and TTs." Signed-off-by:
-
Paul Mackerras authored
commit f948501b upstream. At present, hard_irq_disable() does nothing on powerpc because of this code in include/linux/interrupt.h: #ifndef hard_irq_disable #define hard_irq_disable() do { } while(0) #endif So we need to make our hard_irq_disable be a macro. It was previously a macro until commit 7230c564 ("powerpc: Rework lazy-interrupt handling") changed it to a static inline function. Acked-by:
Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by:
Paul Mackerras <paulus@samba.org> Signed-off-by:
-
Matthew Garrett authored
commit 7dea9665 upstream. HFS+ doesn't really implement hard links - instead, hardlinks are indicated by a magic file type which refers to an indirect node in a hidden directory. The spec indicates that stat() should return the inode number of the indirect node, but it turns out that this doesn't satisfy the firmware when it's looking for a bootloader - it wants the catalog ID of the hardlink file instead. Fix up this case. Signed-off-by:
Matthew Garrett <mjg@redhat.com> Signed-off-by:
Christoph Hellwig <hch@lst.de> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Janne Kalliomäki authored
commit a6dc8c04 upstream. The variable io_size was unsigned int, which caused the wrong sector number to be calculated after aligning it. This then caused mount to fail with big volumes, as backup volume header information was searched from a wrong sector. Signed-off-by:
Janne Kalliomäki <janne@tuxera.com> Signed-off-by:
-
Seiji Aguchi authored
commit 62be73ea upstream. This patch moves kmsg_dump(KMSG_DUMP_PANIC) below smp_send_stop(), to serialize the crash-logging process via smp_send_stop() and to thus retrieve a more stable crash image of all CPUs stopped. Signed-off-by:
Seiji Aguchi <seiji.aguchi@hds.com> Acked-by:
Don Zickus <dzickus@redhat.com> Cc: dle-develop@lists.sourceforge.net <dle-develop@lists.sourceforge.net> Cc: Satoru Moriya <satoru.moriya@hds.com> Cc: Tony Luck <tony.luck@intel.com> Cc: a.p.zijlstra@chello.nl <a.p.zijlstra@chello.nl> Link: http://lkml.kernel.org/r/5C4C569E8A4B9B42A84A977CF070A35B2E4D7A5CE2@USINDEVS01.corp.hds.comSigned-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Johan Hovold authored
commit 4273f987 upstream. Commit 8b4c6a3a ("USB: option: Use generic USB wwan code") moved option port-data allocation to usb_wwan_startup but still cast the port data to the old struct... Signed-off-by:
Johan Hovold <jhovold@gmail.com> Signed-off-by:
-
Johan Hovold authored
commit b9c3aab3 upstream. Fix memory leak introduced by commit 383cedc3 ("USB: serial: full autosuspend support for the option driver") which allocates usb-serial data but never frees it. Signed-off-by:
-
说不得 authored
commit 0ef0be15 upstream. Signed-off-by:
gavin zhu <gavin.zhu@qq.com> Signed-off-by:
-
Andrew Bird authored
commit 42ca7da1 upstream. Later firmwares for this device now have proper subclass and protocol info so we can identify it nicely without needing to use the blacklist. I'm not removing the old 0xff matching as there may be devices in the field that still need that. Signed-off-by:
Andrew Bird <ajb@spheresystems.co.uk> Signed-off-by:
-
Bjørn Mork authored
commit 4cbbb039 upstream. Tested-by:
Thomas Schäfer <tschaefer@t-online.de> Signed-off-by:
-
Hugh Dickins authored
commit 9b15b817 upstream. Minchan Kim reports that when a system has many swap areas, and tmpfs swaps out to the ninth or more, shmem_getpage_gfp()'s attempts to read back the page cannot locate it, and the read fails with -ENOMEM. Whoops. Yes, I blindly followed read_swap_header()'s pte_to_swp_entry( swp_entry_to_pte()) technique for determining maximum usable swap offset, without stopping to realize that that actually depends upon the pte swap encoding shifting swap offset to the higher bits and truncating it there. Whereas our radix_tree swap encoding leaves offset in the lower bits: it's swap "type" (that is, index of swap area) that was truncated. Fix it by reducing the SWP_TYPE_SHIFT() in swapops.h, and removing the broken radix_to_swp_entry(swp_to_radix_entry()) from read_swap_header(). This does not reduce the usable size of a swap area any further, it leaves it as claimed when making the original commit: no change from 3.0 on x86_64, nor on i386 without PAE; but 3.0's 512GB is reduced to 128GB per swapfile on i386 with PAE. It's not a change I would have risked five years ago, but with x86_64 supported for ten years, I believe it's appropriate now. Hmm, and what if some architecture implements its swap pte with offset encoded below type? That would equally break the maximum usable swap offset check. Happily, they all follow the same tradition of encoding offset above type, but I'll prepare a check on that for next. Reported-and-Reviewed-and-Tested-by:
Minchan Kim <minchan@kernel.org> Signed-off-by:
Hugh Dickins <hughd@google.com> Signed-off-by:
-
nagalakshmi.nandigama@lsi.com authored
commit a2c65850 upstream. When CONFIG_DEBUG_PREEMPT is enabled, bug is observed in the smp_processor_id(). This is because smp_processor_id() is not called in preempt safe condition. To fix this issue, use raw_smp_processor_id instead of smp_processor_id. Signed-off-by:
Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com> Signed-off-by:
James Bottomley <JBottomley@Parallels.com> Signed-off-by:
-
Jeff Layton authored
commit 92123e06 upstream. In the event that we don't have a dentry for a rpc_pipefs pipe, we still need to allow the queue_timeout job to clean out the queue. There's just no waitq to wake up in that event. Reported-by:
Hans de Bruin <jmdebruin@xmsnet.nl> Reported-by:
Joerg Platte <jplatte@naasa.net> Signed-off-by:
Jeff Layton <jlayton@redhat.com> Signed-off-by:
Trond Myklebust <Trond.Myklebust@netapp.com> Signed-off-by:
-
Steven Rostedt authored
commit f2bf1f6f upstream. A recent update to have tracing_on/off() only affect the ftrace ring buffers instead of all ring buffers had a cut and paste error. The tracing_off() did the exact same thing as tracing_on() and would not actually turn off tracing. Unfortunately, tracing_off() is more important to be working than tracing_on() as this is a key development tool, as it lets the developer turn off tracing as soon as a problem is discovered. It is also used by panic and oops code. This bug also breaks the 'echo func:traceoff > set_ftrace_filter' Signed-off-by:
Steven Rostedt <rostedt@goodmis.org> Signed-off-by:
-
J. Bruce Fields authored
commit bc2df47a upstream. Most frequent symptom was a BUG triggering in expire_client, with the server locking up shortly thereafter. Introduced by 508dc6e1 "nfsd41: free_session/free_client must be called under the client_lock". Cc: Benny Halevy <bhalevy@tonian.com> Signed-off-by:
J. Bruce Fields <bfields@redhat.com> Signed-off-by:
-
Trond Myklebust authored
commit 2d0dbc6a upstream. While nfs4_do_open() expects the fmode argument to be restricted to combinations of FMODE_READ and FMODE_WRITE, both nfs4_atomic_open() and nfs4_proc_create will pass the nfs_open_context->mode, which contains the full fmode_t. This patch ensures that nfs4_do_open strips the other fmode_t bits, fixing a problem in which the nfs4_do_open call would result in an unnecessary delegation return. Reported-by:
Fred Isaman <iisaman@netapp.com> Signed-off-by:
-
Trond Myklebust authored
commit b3b02ae5 upstream. If the call to svc_process_common() fails, then the request needs to be freed before we can exit bc_svc_process. Signed-off-by:
-
Andre Przywara authored
commit 5e626254 upstream. Xen PV kernels allow access to the APERF/MPERF registers to read the effective frequency. Access to the MSRs is however redirected to the currently scheduled physical CPU, making consecutive read and compares unreliable. In addition each rdmsr traps into the hypervisor. So to avoid bogus readouts and expensive traps, disable the kernel internal feature flag for APERF/MPERF if running under Xen. This will a) remove the aperfmperf flag from /proc/cpuinfo b) not mislead the power scheduler (arch/x86/kernel/cpu/sched.c) to use the feature to improve scheduling (by default disabled) c) not mislead the cpufreq driver to use the MSRs This does not cover userland programs which access the MSRs via the device file interface, but this will be addressed separately. Signed-off-by:
Andre Przywara <andre.przywara@amd.com> Signed-off-by:
Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by:
-
Konrad Rzeszutek Wilk authored
commit 5842f576 upstream. We need to make sure that those parameters are setup to be correct. As such the value of 0 is deemed invalid and we find that we bail out. The hypervisor sets by default all of them to be zero and when the hypercall is done does a simple: a.value = d->arch.hvm_domain.params[a.index]; Which means that if the Xen toolstack forgot to setup the proper HVM_PARAM_CONSOLE_EVTCHN (or the PFN one), we would get the default value of 0 and use that. Fixes-Oracle-Bug: 14091238 Signed-off-by:
-
Konrad Rzeszutek Wilk authored
commit a32c88b9 upstream. We weren't resetting the parameter to be passed in to a known default. Nor were we checking the return value of hvm_get_parameter. Signed-off-by:
-
Konrad Rzeszutek Wilk authored
commit 2e5ad6b9 upstream. All of the error paths are doing the same logic. In which case we might as well collapse them in one path. Acked-by:
Stefano Stabellini <stefano.stabellini@eu.citrix.com> Signed-off-by:
-
Márton Németh authored
commit 648ccc7d upstream. The filed object_idr of struct drm_sis_private was introduced with commit http://git.kernel.org/?p=linux/kernel/git/torvalds/linux.git;a=commitdiff;h=6de8a748881f1cd9d795454da2b6db616d5ca3d7 . The idr_init(&dev->object_name_idr) is called instead of idr_init(&dev_priv->object_idr) by mistake, leaving object_idr uninitialized. Correct this. This patch was not tested because of lack of hardware. Signed-off-by:
Márton Németh <nm127@freemail.hu> Reviewed-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by:
Dave Airlie <airlied@redhat.com> Signed-off-by:
-
Dave Airlie authored
commit e5a867a5 upstream. This is ported from udlfb. Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=832188Signed-off-by:
-
Márton Németh authored
commit ce020ea5 upstream. The field obejct_idr of struct drm_via_private was introduced with the commit http://git.kernel.org/?p=linux/kernel/git/torvalds/linux.git;a=commitdiff;h=77ee8f3825054f23b17e9c8f728f061defd86cdc . In that patch idr_init(&dev->object_name_idr) was called instead of idr_init(&dev_priv->object_idr) by mistake, leaving the dev_priv->object_idr uninitialized. To be more exact, the object_idr buffer is filled with zeros because of kzalloc(), but the dev_priv->object_idr.lock spinlock can cause system freeze at lib/idr.c:move_to_free_list() when spin_lock_irqsave() is called on this spinlock. The patch was tested on Clevo D4J, model D410J laptop, on the following hardware, without AGP kernel module loaded: # lspci -s 01:00.0 -n 01:00.0 0300: 1106:3108 (rev 01) # lspci -s 01:00.0 -v 01:00.0 VGA compatible controller: VIA Technologies, Inc. K8M800/K8N800/K8N800A [S3 UniChrome Pro] (rev 01) (prog-if 00 [VGA controller]) Subsystem: CLEVO/KAPOK Computer Device 4702 Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 16 Memory at f0000000 (32-bit, prefetchable) [size=64M] Memory at d1000000 (32-bit, non-prefetchable) [size=16M] Expansion ROM at <unassigned> [disabled] Capabilities: [60] Power Management version 2 Capabilities: [70] AGP version 3.0 Signed-off-by:
-
Alex Deucher authored
commit b866d133 upstream. - SMX_SAR_CTL0 needs to be programmed correctly to prevent problems with memory exports in certain cases. - VC_ENHANCE needs to be initialized on 6xx/7xx. Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
-
Daniel Vetter authored
commit 6b4e0a93 upstream. This reverts commit 092945e1. This commit prevents a DP screen from properly training the link. Oddly enough it works, once the machine has been warm-booted with an older kernel. According to DP docs this _should_ have been the right precharge time. Also, the commit that originally introduces this was just general snb DP enabling and didn't mention any specific reason for this special value. Whatever, trust the reporter that this makes things worse and let's just revert it. v2: Less spelling fail. Reviewed-by:
Adam Jackson <ajax@redhat.com> Cc: Jesse Barnes <jbarnes@virtuousgeek.org> Reported-by:
"Wouter M. Koolen" <W.M.Koolen-Wijkstra@cwi.nl> Buglink: https://lkml.org/lkml/2012/6/14/301Signed-Off-by:
-
Jaccon Bastiaansen authored
commit 350ab15b upstream. The statically defined I/O memory regions for the i.MX21 on chip peripherals and the on board I/O peripherals of the i.MX21ADS board overlap. This results in a kernel crash during startup. This is fixed by reducing the memory range for the on board I/O peripherals to the actually required range. Signed-off-by:
Jaccon Bastiaansen <jaccon.bastiaansen@gmail.com> Signed-off-by:
Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by:
-
Shawn Guo authored
commit 602bf409 upstream. There is a system hang issue on imx6q which can easily be seen with running a cpu hotplug stress testing (hotplug secondary cores from user space via sysfs interface for thousands iterations). It turns out that the issue is caused by coherency of the cpu that is being shut down. When shutting down a cpu, we need to have the cpu exit coherency to prevent it from receiving cache, TLB, or BTB maintenance operations broadcast by other CPUs in the cluster. Copy cpu_enter_lowpower() and cpu_leave_lowpower() from mach-vexpress to have coherency properly handled in platform_cpu_die(), thus fix the issue. Signed-off-by:
Shawn Guo <shawn.guo@linaro.org> Signed-off-by:
-
Sascha Hauer authored
commit cdd781ab upstream. MX53_DPLL4_BASE accidently returned the base address of PLL3. Fix this. Signed-off-by:
-
- 17 Jun, 2012 5 commits
-
-
Greg Kroah-Hartman authored
-
Andy Whitcroft authored
commit cd006086 upstream. When we are hosted on a Microsoft Hyper-V hypervisor the guest disks are exposed both via the Hyper-V paravirtualised drivers and via an emulated SATA disk drive. In this case we want to use the paravirtualised drivers if we can as they are much more efficient. Note that the Hyper-V paravirtualised drivers only expose the virtual hard disk devices, the CDROM/DVD devices must still be enumerated. Mark the host controller ATA_HOST_IGNORE_ATA to prevent enumeration of disk devices. BugLink: http://bugs.launchpad.net/bugs/929545 BugLink: http://bugs.launchpad.net/bugs/942316Signed-off-by:
Andy Whitcroft <apw@canonical.com> Signed-off-by:
Jeff Garzik <jgarzik@redhat.com> Cc: Victor Miasnikov <vvm@tut.by> Signed-off-by:
-
Andy Whitcroft authored
commit db63a4c8 upstream. Where devices are visible via more than one host we sometimes wish to indicate that cirtain devices should be ignored on a specific host. Add a host flag indicating that this host wishes to ignore ATA specific devices. Signed-off-by:
-
Pavel Shilovsky authored
commit 45c72cd7 upstream. Now we store attr->ino at inode->i_ino, return attr->ino at the first time and then return inode->i_ino if the attribute timeout isn't expired. That's wrong on 32 bit platforms because attr->ino is 64 bit and inode->i_ino is 32 bit in this case. Fix this by saving 64 bit ino in fuse_inode structure and returning it every time we call getattr. Also squash attr->ino into inode->i_ino explicitly. Signed-off-by:
Pavel Shilovsky <piastry@etersoft.ru> Signed-off-by:
Miklos Szeredi <mszeredi@suse.cz> Signed-off-by:
-
Chris Wilson authored
commit 3eef8918 upstream. By correctly describing the rinbuffers as being in the GTT domain, it appears that we are more careful with the management of the CPU cache upon resume and so prevent some coherency issue when submitting commands to the GPU later. A secondary effect is that the debug logs are then consistent with the actual usage (i.e. they no longer describe the ringbuffers as being in the CPU write domain when we are accessing them through an wc iomapping.) Reported-and-tested-by:
Daniel Gnoutcheff <daniel@gnoutcheff.name> Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=41092Signed-off-by:
Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by:
-
