- 15 Nov, 2017 13 commits
-
-
Eric Dumazet authored
pcpu_freelist_pop() needs the same lockdep awareness than pcpu_freelist_populate() to avoid a false positive. [ INFO: SOFTIRQ-safe -> SOFTIRQ-unsafe lock order detected ] switchto-defaul/12508 [HC0[0]:SC0[6]:HE0:SE0] is trying to acquire: (&htab->buckets[i].lock){......}, at: [<ffffffff9dc099cb>] __htab_percpu_map_update_elem+0x1cb/0x300 and this task is already holding: (dev_queue->dev->qdisc_class ?: &qdisc_tx_lock#2){+.-...}, at: [<ffffffff9e135848>] __dev_queue_xmit+0 x868/0x1240 which would create a new lock dependency: (dev_queue->dev->qdisc_class ?: &qdisc_tx_lock#2){+.-...} -> (&htab->buckets[i].lock){......} but this new dependency connects a SOFTIRQ-irq-safe lock: (dev_queue->dev->qdisc_class ?: &qdisc_tx_lock#2){+.-...} ... which became SOFTIRQ-irq-safe at: [<ffffffff9db5931b>] __lock_acquire+0x42b/0x1f10 [<ffffffff9db5b32c>] lock_acquire+0xbc/0x1b0 [<ffffffff9da05e38>] _raw_spin_lock+0x38/0x50 [<ffffffff9e135848>] __dev_queue_xmit+0x868/0x1240 [<ffffffff9e136240>] dev_queue_xmit+0x10/0x20 [<ffffffff9e1965d9>] ip_finish_output2+0x439/0x590 [<ffffffff9e197410>] ip_finish_output+0x150/0x2f0 [<ffffffff9e19886d>] ip_output+0x7d/0x260 [<ffffffff9e19789e>] ip_local_out+0x5e/0xe0 [<ffffffff9e197b25>] ip_queue_xmit+0x205/0x620 [<ffffffff9e1b8398>] tcp_transmit_skb+0x5a8/0xcb0 [<ffffffff9e1ba152>] tcp_write_xmit+0x242/0x1070 [<ffffffff9e1baffc>] __tcp_push_pending_frames+0x3c/0xf0 [<ffffffff9e1b3472>] tcp_rcv_established+0x312/0x700 [<ffffffff9e1c1acc>] tcp_v4_do_rcv+0x11c/0x200 [<ffffffff9e1c3dc2>] tcp_v4_rcv+0xaa2/0xc30 [<ffffffff9e191107>] ip_local_deliver_finish+0xa7/0x240 [<ffffffff9e191a36>] ip_local_deliver+0x66/0x200 [<ffffffff9e19137d>] ip_rcv_finish+0xdd/0x560 [<ffffffff9e191e65>] ip_rcv+0x295/0x510 [<ffffffff9e12ff88>] __netif_receive_skb_core+0x988/0x1020 [<ffffffff9e130641>] __netif_receive_skb+0x21/0x70 [<ffffffff9e1306ff>] process_backlog+0x6f/0x230 [<ffffffff9e132129>] net_rx_action+0x229/0x420 [<ffffffff9da07ee8>] __do_softirq+0xd8/0x43d [<ffffffff9e282bcc>] do_softirq_own_stack+0x1c/0x30 [<ffffffff9dafc2f5>] do_softirq+0x55/0x60 [<ffffffff9dafc3a8>] __local_bh_enable_ip+0xa8/0xb0 [<ffffffff9db4c727>] cpu_startup_entry+0x1c7/0x500 [<ffffffff9daab333>] start_secondary+0x113/0x140 to a SOFTIRQ-irq-unsafe lock: (&head->lock){+.+...} ... which became SOFTIRQ-irq-unsafe at: ... [<ffffffff9db5971f>] __lock_acquire+0x82f/0x1f10 [<ffffffff9db5b32c>] lock_acquire+0xbc/0x1b0 [<ffffffff9da05e38>] _raw_spin_lock+0x38/0x50 [<ffffffff9dc0b7fa>] pcpu_freelist_pop+0x7a/0xb0 [<ffffffff9dc08b2c>] htab_map_alloc+0x50c/0x5f0 [<ffffffff9dc00dc5>] SyS_bpf+0x265/0x1200 [<ffffffff9e28195f>] entry_SYSCALL_64_fastpath+0x12/0x17 other info that might help us debug this: Chain exists of: dev_queue->dev->qdisc_class ?: &qdisc_tx_lock#2 --> &htab->buckets[i].lock --> &head->lock Possible interrupt unsafe locking scenario: CPU0 CPU1 ---- ---- lock(&head->lock); local_irq_disable(); lock(dev_queue->dev->qdisc_class ?: &qdisc_tx_lock#2); lock(&htab->buckets[i].lock); <Interrupt> lock(dev_queue->dev->qdisc_class ?: &qdisc_tx_lock#2); *** DEADLOCK *** Fixes: e19494ed ("bpf: introduce percpu_freelist") Signed-off-by:Eric Dumazet <edumazet@google.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Bjørn Mork authored
The GetNtbFormat and SetNtbFormat requests operate on 16 bit little endian values. We get away with ignoring this most of the time, because we only care about USB_CDC_NCM_NTB16_FORMAT which is 0x0000. This fails for USB_CDC_NCM_NTB32_FORMAT. Fix comparison between LE value from device and constant by converting the constant to LE. Reported-by:
Ben Hutchings <ben.hutchings@codethink.co.uk> Fixes: 2b02c20c ("cdc_ncm: Set NTB format again after altsetting switch for Huawei devices") Cc: Enrico Mioso <mrkiko.rs@gmail.com> Cc: Christian Panton <christian@panton.org> Signed-off-by:
Bjørn Mork <bjorn@mork.no> Acked-By:
Enrico Mioso <mrkiko.rs@gmail.com> Signed-off-by:
-
Gustavo A. R. Silva authored
It seems that the intention of the code is to null check the value returned by function genlmsg_put. But the current code is null checking the address of the pointer that holds the value returned by genlmsg_put. Fix this by properly null checking the value returned by function genlmsg_put in order to avoid a pontential null pointer dereference. Addresses-Coverity-ID: 1461561 ("Dereference before null check") Addresses-Coverity-ID: 1461562 ("Dereference null return value") Fixes: 96fbc13d ("openvswitch: Add meter infrastructure") Signed-off-by:Gustavo A. R. Silva <garsilva@embeddedor.com> Signed-off-by:
-
David S. Miller authored
Stephen Hemminger says: ==================== netem: fix compilation on 32 bit A couple of places where 64 bit CPU was being assumed incorrectly. ==================== Signed-off-by: -
Stephen Hemminger authored
Fix compilation on 32 bit platforms (where doing modulus operation with 64 bit requires extra glibc functions) by truncation. The jitter for table distribution is limited to a 32 bit value because random numbers are scaled as 32 bit value. Also fix some whitespace. Fixes: 99803171 ("netem: add uapi to express delay and jitter in nanoseconds") Reported-by:
Randy Dunlap <rdunlap@infradead.org> Signed-off-by:
Stephen Hemminger <stephen@networkplumber.org> Signed-off-by:
-
Stephen Hemminger authored
Since times are now expressed in nanosecond, need to now do true 64 bit divide. Old code would truncate rate at 32 bits. Rename function to better express current usage. Signed-off-by:
-
Stephen Hemminger authored
Make default TCP default congestion control to a per namespace value. This changes default congestion control to a pointer to congestion ops (rather than implicit as first element of available lsit). The congestion control setting of new namespaces is inherited from the current setting of the root namespace. Signed-off-by:
Stephen Hemminger <sthemmin@microsoft.com> Reviewed-by:
-
Kirill Tkhai authored
There is at least unlocked deletion of net->ipv4.fib_notifier_ops from net::fib_notifier_ops: ip_fib_net_exit() rtnl_unlock() fib4_notifier_exit() fib_notifier_ops_unregister(net->ipv4.notifier_ops) list_del_rcu(&ops->list) So fib_seq_sum() can't use rtnl_lock() only for protection. The possible solution could be to use rtnl_lock() in fib_notifier_ops_unregister(), but this adds a possible delay during net namespace creation, so we better use rcu_read_lock() till someone really needs the mutex (if that happens). Signed-off-by:Kirill Tkhai <ktkhai@virtuozzo.com> Signed-off-by:
-
Nicolas Dichtel authored
With commits 35e015e1 and a2d3f3e3, the global 'accept_dad' flag is also taken into account (default value is 1). If either global or per-interface flag is non-zero, DAD will be enabled on a given interface. This is not backward compatible: before those patches, the user could disable DAD just by setting the per-interface flag to 0. Now, the user instead needs to set both flags to 0 to actually disable DAD. Restore the previous behaviour by setting the default for the global 'accept_dad' flag to 0. This way, DAD is still enabled by default, as per-interface flags are set to 1 on device creation, but setting them to 0 is enough to disable DAD on a given interface. - Before 35e015e1f57a7 and a2d3f3e3: global per-interface DAD enabled [default] 1 1 yes X 0 no X 1 yes - After 35e015e1 and a2d3f3e3: global per-interface DAD enabled [default] 1 1 yes 0 0 no 0 1 yes 1 0 yes - After this fix: global per-interface DAD enabled 1 1 yes 0 0 no [default] 0 1 yes 1 0 yes Fixes: 35e015e1 ("ipv6: fix net.ipv6.conf.all interface DAD handlers") Fixes: a2d3f3e3 ("ipv6: fix net.ipv6.conf.all.accept_dad behaviour for real") CC: Stefano Brivio <sbrivio@redhat.com> CC: Matteo Croce <mcroce@redhat.com> CC: Erik Kline <ek@google.com> Signed-off-by:
Nicolas Dichtel <nicolas.dichtel@6wind.com> Acked-by:
Stefano Brivio <sbrivio@redhat.com> Signed-off-by:
-
Dmitry V. Levin authored
Move inclusion of a private kernel header <net/tcp.h> from uapi/linux/tls.h to its only user - net/tls.h, to fix the following linux/tls.h userspace compilation error: /usr/include/linux/tls.h:41:21: fatal error: net/tcp.h: No such file or directory As to this point uapi/linux/tls.h was totaly unusuable for userspace, cleanup this header file further by moving other redundant includes to net/tls.h. Fixes: 3c4d7559 ("tls: kernel TLS support") Cc: <stable@vger.kernel.org> # v4.13+ Signed-off-by:
Dmitry V. Levin <ldv@altlinux.org> Signed-off-by:
-
Alexander Kappner authored
iOS devices require the host to be "trusted" before servicing network packets. Establishing trust requires the user to confirm a dialog on the iOS device.Until trust is established, the iOS device will silently discard network packets from the host. Currently, the ipheth driver does not detect whether an iOS device has established trust with the host, and immediately sets up the transmit queues. This causes the following problems: - Kernel taint due to WARN() in netdev watchdog. - Dmesg spam ("TX timeout"). - Disruption of user space networking activity (dhcpd, etc...) when new interface comes up but cannot be used. - Unnecessary host and device wakeups and USB traffic Example dmesg output: [ 1101.319778] NETDEV WATCHDOG: eth1 (ipheth): transmit queue 0 timed out [ 1101.319817] ------------[ cut here ]------------ [ 1101.319828] WARNING: CPU: 0 PID: 0 at net/sched/sch_generic.c:316 dev_watchdog+0x20f/0x220 [ 1101.319831] Modules linked in: ipheth usbmon nvidia_drm(PO) nvidia_modeset(PO) nvidia(PO) iwlmvm mac80211 iwlwifi btusb btrtl btbcm btintel qmi_wwan bluetooth cfg80211 ecdh_generic thinkpad_acpi rfkill [last unloaded: ipheth] [ 1101.319861] CPU: 0 PID: 0 Comm: swapper/0 Tainted: P O 4.13.12.1 #1 [ 1101.319864] Hardware name: LENOVO 20ENCTO1WW/20ENCTO1WW, BIOS N1EET62W (1.35 ) 11/10/2016 [ 1101.319867] task: ffffffff81e11500 task.stack: ffffffff81e00000 [ 1101.319873] RIP: 0010:dev_watchdog+0x20f/0x220 [ 1101.319876] RSP: 0018:ffff8810a3c03e98 EFLAGS: 00010292 [ 1101.319880] RAX: 000000000000003a RBX: 0000000000000000 RCX: 0000000000000000 [ 1101.319883] RDX: ffff8810a3c15c48 RSI: ffffffff81ccbfc2 RDI: 00000000ffffffff [ 1101.319886] RBP: ffff880c04ebc41c R08: 0000000000000000 R09: 0000000000000379 [ 1101.319889] R10: 00000100696589d0 R11: 0000000000000378 R12: ffff880c04ebc000 [ 1101.319892] R13: 0000000000000000 R14: 0000000000000001 R15: ffff880c2865fc80 [ 1101.319896] FS: 0000000000000000(0000) GS:ffff8810a3c00000(0000) knlGS:0000000000000000 [ 1101.319899] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 1101.319902] CR2: 00007f3ff24ac000 CR3: 0000000001e0a000 CR4: 00000000003406f0 [ 1101.319905] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 1101.319908] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 1101.319910] Call Trace: [ 1101.319914] <IRQ> [ 1101.319921] ? dev_graft_qdisc+0x70/0x70 [ 1101.319928] ? dev_graft_qdisc+0x70/0x70 [ 1101.319934] ? call_timer_fn+0x2e/0x170 [ 1101.319939] ? dev_graft_qdisc+0x70/0x70 [ 1101.319944] ? run_timer_softirq+0x1ea/0x440 [ 1101.319951] ? timerqueue_add+0x54/0x80 [ 1101.319956] ? enqueue_hrtimer+0x38/0xa0 [ 1101.319963] ? __do_softirq+0xed/0x2e7 [ 1101.319970] ? irq_exit+0xb4/0xc0 [ 1101.319976] ? smp_apic_timer_interrupt+0x39/0x50 [ 1101.319981] ? apic_timer_interrupt+0x8c/0xa0 [ 1101.319983] </IRQ> [ 1101.319992] ? cpuidle_enter_state+0xfa/0x2a0 [ 1101.319999] ? do_idle+0x1a3/0x1f0 [ 1101.320004] ? cpu_startup_entry+0x5f/0x70 [ 1101.320011] ? start_kernel+0x444/0x44c [ 1101.320017] ? early_idt_handler_array+0x120/0x120 [ 1101.320023] ? x86_64_start_kernel+0x145/0x154 [ 1101.320028] ? secondary_startup_64+0x9f/0x9f [ 1101.320033] Code: 20 04 00 00 eb 9f 4c 89 e7 c6 05 59 44 71 00 01 e8 a7 df fd ff 89 d9 4c 89 e6 48 c7 c7 70 b7 cd 81 48 89 c2 31 c0 e8 97 64 90 ff <0f> ff eb bf 66 66 66 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 [ 1101.320103] ---[ end trace 0cc4d251e2b57080 ]--- [ 1101.320110] ipheth 1-5:4.2: ipheth_tx_timeout: TX timeout The last message "TX timeout" is repeated every 5 seconds until trust is established or the device is disconnected, filling up dmesg. The proposed patch eliminates the problem by, upon connection, keeping the TX queue and carrier disabled until a packet is first received from the iOS device. This is reflected by the confirmed_pairing variable in the device structure. Only after at least one packet has been received from the iOS device, the transmit queue and carrier are brought up during the periodic device poll in ipheth_carrier_set. Because the iOS device will always send a packet immediately upon trust being established, this should not delay the interface becoming useable. To prevent failed UBRs in ipheth_rcvbulk_callback from perpetually re-enabling the queue if it was disabled, a new check is added so only successful transfers re-enable the queue, whereas failed transfers only trigger an immediate poll. This has the added benefit of removing the periodic control requests to the iOS device until trust has been established and thus should reduce wakeup events on both the host and the iOS device. Signed-off-by:Alexander Kappner <agk@godking.net> Signed-off-by:
-
Jason Wang authored
We always poll tx for socket, this is sub optimal since this will slightly increase the waitqueue traversing time and more important, vhost could not benefit from commit 9e641bdc ("net-tun: restructure tun_do_read for better sleep/wakeup efficiency") even if we've stopped rx polling during handle_rx(), tx poll were still left in the waitqueue. Pktgen from a remote host to VM over mlx4 on two 2.00GHz Xeon E5-2650 shows 11.7% improvements on rx PPS. (from 1.28Mpps to 1.44Mpps) Cc: Wei Xu <wexu@redhat.com> Cc: Matthew Rosato <mjrosato@linux.vnet.ibm.com> Signed-off-by:
Jason Wang <jasowang@redhat.com> Signed-off-by:
-
Dmitry V. Levin authored
Consistently use types provided by <linux/types.h> to fix the following linux/rxrpc.h userspace compilation errors: /usr/include/linux/rxrpc.h:24:2: error: unknown type name 'u16' u16 srx_service; /* service desired */ /usr/include/linux/rxrpc.h:25:2: error: unknown type name 'u16' u16 transport_type; /* type of transport socket (SOCK_DGRAM) */ /usr/include/linux/rxrpc.h:26:2: error: unknown type name 'u16' u16 transport_len; /* length of transport address */ Use __kernel_sa_family_t instead of sa_family_t the same way as uapi/linux/in.h does, to fix the following linux/rxrpc.h userspace compilation errors: /usr/include/linux/rxrpc.h:23:2: error: unknown type name 'sa_family_t' sa_family_t srx_family; /* address family */ /usr/include/linux/rxrpc.h:28:3: error: unknown type name 'sa_family_t' sa_family_t family; /* transport address family */ Fixes: 727f8914 ("rxrpc: Expose UAPI definitions to userspace") Cc: <stable@vger.kernel.org> # v4.14 Signed-off-by:
-
- 14 Nov, 2017 27 commits
-
-
Niklas Cassel authored
The LPI transitioning logic in stmmac_main uses priv->tx_path_in_lpi_mode to enter/exit LPI. However, priv->tx_path_in_lpi_mode is assigned using the return value from host_irq_status(). So for dwmac4, priv->tx_path_in_lpi_mode was always false, so stmmac_tx_clean() would always try to put us in eee mode, and stmmac_xmit() would never take us out of eee mode. To fix this, make host_irq_status() read and return the LPI irq status also for dwmac4. This also increments the existing LPI counters, so that ethtool --statistics shows LPI transitions also for dwmac4. For dwmac1000, irqs are enabled/disabled using the register named "Interrupt Mask Register", and thus setting a bit disables that specific irq. For dwmac4 the matching register is named "MAC_Interrupt_Enable", and thus setting a bit enables that specific irq. Looking at dwmac1000_core.c, the irqs that are always enabled are: LPI and PMT. Looking at dwmac4_core.c, the irqs that are always enabled are: PMT. To be able to read the LPI irq status, we need to enable the LPI irq also for dwmac4. Signed-off-by:
Niklas Cassel <niklas.cassel@axis.com> Signed-off-by:
-
Arvind Yadav authored
atm_dev_register() can fail here and passed parameters to free irq which is not initialised. Initialization of 'dev->irq' happened after the 'goto out_free_irq'. So using 'irq' insted of 'dev->irq' in free_irq(). Signed-off-by:
Arvind Yadav <arvind.yadav.cs@gmail.com> Signed-off-by:
-
Roopa Prabhu authored
This patch adds netlink notifications on iflias changes via sysfs. makes it consistent with the netlink path which also calls netdev_state_change. Also makes it consistent with other sysfs netdev_store operations. Signed-off-by:
Roopa Prabhu <roopa@cumulusnetworks.com> Reviewed-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
-
Wei Yongjun authored
The callback function of call_rcu() just calls a kfree(), so we can use kfree_rcu() instead of call_rcu() + callback function. Signed-off-by:
Wei Yongjun <weiyongjun1@huawei.com> Acked-by:
Pravin B Shelar <pshelar@ovn.org> Signed-off-by:
-
Wei Yongjun authored
Fixes the following sparse warnings: net/openvswitch/flow_netlink.c:340:8: warning: symbol 'ovs_nsh_key_attr_size' was not declared. Should it be static? Signed-off-by:
-
Wei Yongjun authored
In case of error, the function ovs_meter_cmd_reply_start() returns ERR_PTR() not NULL. The NULL test in the return value check should be replaced with IS_ERR(). Fixes: 96fbc13d ("openvswitch: Add meter infrastructure") Signed-off-by:
-
Dan Carpenter authored
We accidentally return success if lio_vf_rep_modinit() fails instead of propogating the error code. Fixes: e20f4696 ("liquidio: synchronize VF representor names with NIC firmware") Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
-
Dan Carpenter authored
The assert statement is supposed to be part of the else branch but the curly braces were accidentally left off. Fixes: 3e29cd0e ("xdp: Sample xdp program implementing ip forward") Signed-off-by:
Daniel Borkmann <daniel@iogearbox.net> Signed-off-by:
-
Desnes Augusto Nunes do Rosario authored
This patch implements and enables VDP support for the ibmvnic driver. Moreover, it includes the implementation of suitable structs, signal transmission/handling and functions which allows the retrival of firmware information from the ibmvnic card through the ethtool command. Signed-off-by:
Desnes A. Nunes do Rosario <desnesn@linux.vnet.ibm.com> Signed-off-by:
Thomas Falcon <tlfalcon@linux.vnet.ibm.com> Signed-off-by:
-
Nikolay Aleksandrov authored
Found another missing port flag policy entry for IFLA_BRPORT_VLAN_TUNNEL so add it now. CC: Roopa Prabhu <roopa@cumulusnetworks.com> Fixes: efa5356b ("bridge: per vlan dst_metadata netlink support") Signed-off-by:
Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Acked-by:
-
Simon Guinot authored
The mvneta controller provides a 8-bit register to update the pending Tx descriptor counter. Then, a maximum of 255 Tx descriptors can be added at once. In the current code the mvneta_txq_pend_desc_add function assumes the caller takes care of this limit. But it is not the case. In some situations (xmit_more flag), more than 255 descriptors are added. When this happens, the Tx descriptor counter register is updated with a wrong value, which breaks the whole Tx queue management. This patch fixes the issue by allowing the mvneta_txq_pend_desc_add function to process more than 255 Tx descriptors. Fixes: 2a90f7e1 ("net: mvneta: add xmit_more support") Cc: stable@vger.kernel.org # 4.11+ Signed-off-by:
Simon Guinot <simon.guinot@sequanux.org> Signed-off-by:
-
Johannes Berg authored
These flags are unused, remove them to be less confusing. Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
-
Johannes Berg authored
netlink_skb_destructor() is actually defined before the first usage in the file, so remove the unnecessary forward declaration. Signed-off-by:
-
Egil Hjelmeland authored
The lan9303 set bits in the host CPU tag indicating if a ingress frame is a trapped IGMP or STP frame. Use these bits to calculate skb->offload_fwd_mark more efficiently. Signed-off-by:
Egil Hjelmeland <privat@egil-hjelmeland.no> Signed-off-by:
-
Salil Mehta authored
This patch migrates the HNS3 driver code from use of depricated PCI MSI/MSI-X interrupt vector allocation/free APIs to new common APIs. Signed-off-by:
Salil Mehta <salil.mehta@huawei.com> Suggested-by:
Christoph Hellwig <hch@lst.de> Signed-off-by:
-
Pan Bian authored
Function devm_gpiod_get_optional() returns an ERR_PTR on failure. Its return value should not be validated by a NULL check. Instead, use IS_ERR. Signed-off-by:
Pan Bian <bianpan2016@163.com> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
-
Heiner Kallweit authored
After commit b94d22d9 "ARM64: dts: meson-gx: add external PHY interrupt on some platforms" ethernet stopped working on my Odroid-C2 which has a RTL8211F phy. It turned out that no interrupts were triggered. Further analysis showed the register INER can't be altered on page 0. Because register INSR needs to be accessed via page 0xa43 I assumed that register INER needs to be accessed via some page too. Some brute force check resulted in page 0xa42 being the right one. With this patch the phy is working properly in interrupt mode. Fixes: 3447cf2e ("net/phy: Add support for Realtek RTL8211F") Signed-off-by:
Heiner Kallweit <hkallweit1@gmail.com> Tested-by:
Jerome Brunet <jbrunet@baylibre.com> Signed-off-by:
-
David S. Miller authored
Jiri Pirko says: ==================== mlxsw: Update firmware version Ido says: This set adjusts the driver to use a new firmware version. The new version includes various enhancements and fixes detailed in the first patch. The second patch enables batch deletion of neighbours on a router interface (RIF) which was not possible with previous versions. ==================== Signed-off-by: -
Ido Schimmel authored
In commit 4a3c67a6 ("mlxsw: spectrum_router: Don't batch neighbour deletion") I removed the support for batch deletion of neighbours on a router interface (RIF) since at that time the firmware did not support it for IPv6 neighbours. This is now supported by the version enforced by the driver, so there is no reason to delete neighbours one by one anymore. Signed-off-by:
Ido Schimmel <idosch@mellanox.com> Signed-off-by:
-
Shalom Toledo authored
This new firmware contains: - Support Spectrum A1 revision - Batch deletion of IPv6 neighbours - Remove incorrect VPD capability Signed-off-by:
Shalom Toledo <shalomt@mellanox.com> Signed-off-by:
-
Harald Welte authored
According to https://www.mail-archive.com/netdev@vger.kernel.org/msg177411.html there is a status page available at http://vger.kernel.org/~davem/net-next.html to obtain the current status of the net-next tree. Let's add this information to the netdev FAQ. Signed-off-by:
Harald Welte <laforge@gnumonks.org> Signed-off-by:
-
Harald Welte authored
* clarify specification references for v0/v1 * add section "APN vs. Network device" * add section "Local GTP-U entity and tunnel identification" Signed-off-by:
Andreas Schultz <aschultz@tpip.net> Signed-off-by:
-
David S. Miller authored
Rasmus Villemoes says: ==================== net: core: devname allocation cleanups It's somewhat confusing to have both dev_alloc_name and dev_get_valid_name. I can't see why the former is less strict than the latter, so make them (or rather dev_alloc_name_ns and dev_get_valid_name) equivalent, hardening dev_alloc_name() a little. Obvious follow-up patches would be to only export one function, and make dev_alloc_name a static inline wrapper for that (whichever name is chosen for the exported interface). But maybe there is a good reason the two exported interfaces do different checking, so I'll refrain from including the trivial but tree-wide renaming in this series. ==================== Signed-off-by: -
Rasmus Villemoes authored
If name contains a %, it's easy to see that this patch doesn't change anything (other than eliminate the duplicate dev_valid_name call). Otherwise, we'll now just spend a little time in snprintf() copying name to the stack buffer allocated in dev_alloc_name_ns, and do the __dev_get_by_name using that buffer rather than name. Signed-off-by:
Rasmus Villemoes <linux@rasmusvillemoes.dk> Signed-off-by:
-
Rasmus Villemoes authored
If we're given format string with no %d, -EEXIST is a saner error code. Signed-off-by:
-
Rasmus Villemoes authored
We currently only exclude non-sysfs-friendly names via dev_get_valid_name; there doesn't seem to be a reason to allow such names when we're called via dev_alloc_name. This does duplicate the dev_valid_name check in the dev_get_valid_name() case; we'll fix that shortly. Signed-off-by:
-
Rasmus Villemoes authored
The only caller passes a stack buffer as buf, so it won't equal the passed-in name. Moreover, we're already using buf as a scratch buffer inside the if (p) {} block, so if buf and name were the same, that snprintf() call would be overwriting its own format string. Signed-off-by:
-
