- 08 Feb, 2008 32 commits
-
-
James Bottomley authored
A lot of SCSI command replies have a protocol ID field. Add definitions for the interpretation of that from SPC-3. Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-
James Bottomley authored
Some devices report medium error locations incorrectly. Add guards to make sure the reported bad lba is actually in the request that caused it. Additionally remove the large case statment for sector sizes and replace it with the proper u64 divisions. Tested-by: Mike Snitzer <snitzer@gmail.com> Cc: Stable Tree <stable@kernel.org> Cc: Tony Battersby <tonyb@cybernetics.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-
Andrew Vasquez authored
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-
Andrew Vasquez authored
[SCSI] qla2xxx: Correct issue where incorrect init-fw mailbox command was used on non-NPIV capable ISPs. BIT_2 of the firmware attributes is only valid on FW-interface-2 type HBAs. Code in commit c48339de would cause the incorrect initialize-firmware mailbox command to be issued for non-NPIV capable ISPs. Correct this by reverting to previously used (and correct) pre-condition 'if' check. Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-
Seokmann Ju authored
For following fc_host specific attributes, vports rely on the pport. So, this patch changed way to access the data for those attributes so that they can access pport's. - get_host_speed (speed) - get_host_port_state (port_state) - get_host_port_type (port_type) - get_fc_host_stats Also, added PORT_SPEED_8GB case in the speed attribute for 8Gb HBAs. Signed-Off-by: Seokmann Ju <seokmann.ju@qlogic.com> Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-
Seokmann Ju authored
While running IO simultaneously through physical port and virtual port, if user changes Data Rate (from scli utility), IO through virtual port fails. It failed because the vport had not received the ISP_ABORT_NEEDED notification. Signed-Off-by: Seokmann Ju <seokmann.ju@qlogic.com> Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-
Andrew Vasquez authored
There's no functional change involved with this update, instead it simply migrates the "set cleared interrupt state" codes to a more approprate method, qla2x00_request_irqs(), and cleans-up the driver's probe() logic. Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-
Andrew Vasquez authored
Collapse duplicate codes called during probe() and RISC-reset into qla2x00_setup_chip(). Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-
Andrew Vasquez authored
- Drop loop-till-allocated structure of code within qla2x00_mem_alloc(). - Properly unwind deallcations of memory during failures. - Drop qla2x00_allocate_sp_pool() and qla2x00_free_sp_pool() functions as their implementations can easily be collapsed into the callers. - Defer DMA pool allocation of SFP data until requested. Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-
Andrew Vasquez authored
To insure that there is no stale data present during EFT re-registration. Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-
Andrew Vasquez authored
Refactor SRB-failure completion codes in the process. Also, signal the DPC routine to complete sooner as backend processing at shutdown-time is superflous. [jejb: resolve conflicts with pci_enable_device_bars removal] Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-
Andrew Vasquez authored
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-
Andrew Vasquez authored
Hmm, it looks like the conversion to resource_size_t usage (3776541d) requires some additional fixups to cleanup the structure-pointer castings used during IO mapped accesses to the chip. There's only a small number of locations, where the driver uses IO mapped accesses to the hardware, the patch below should take care of it without introducing to many structural changes to code flow. Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-
Mike Christie authored
Set iscsi version to 2.0-868 Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-
Mike Christie authored
The session age mask is only 4 bits, but session->age is 32. When it gets larger then 15 and we try to or the bits some bits get dropped and the check for session age in iscsi_verify_itt is useless. The ISCSI_CID_MASK related bits are also useless since cid is always one. Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-
Mike Christie authored
Some iscsi class messages have the dev_printk prefix and some libiscsi and iscsi_tcp messages have "iscsi" or the module name as a prefix which is normally pretty useless when trying to figure out which session or connection the message is attached to. This patch adds iscsi lib and class dev_printks so all messages have a common prefix that can be used to figure out which object printed it. Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-
Mike Christie authored
There are 13 iscsi conn attrs, but since the IF/OF markers were not being used we did not notice that we forgot to increment the ISCSI_CONN_ATTRS counter. Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-
Mike Christie authored
If we rollover then we could get a next_timeout of zero, so we need to set the new timer to that value. Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-
Mike Christie authored
qla4xxx has the old school startup/probe where it finds presetup sessions in its flash and then attempts to log into them before returning from the probe. This however, makes it very simple to add a iscsi class scan finished helper which the driver can use. In future patches Dave or I will rip apart the driver to make it more like qla2xxx, but for now this is a very simple two line patch which fixes the problem of trying to figure out when the initial sessions are done being scanned. Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Cc: David Somayajulu <david.somayajulu@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-
Mike Christie authored
In qla4xxx's probe it will call the iscsi session setup functions for session that got setup on the initial start. This then makes it easy for the iscsi class to export a helper which indicates when those scans are done. Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-
Mike Christie authored
If qla4xxx is resetting up a session and the recovery timer fires we do not want to just set it to dead, because the dpc thread could have just set it to online and is in the middle of resetting it up. Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Cc: David Somayajulu <david.somayajulu@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-
Mike Christie authored
This just adds iscsi session scanning which works like fc rport scanning. The future patches will hook the drivers into Mathew Wilcox's async scanning infrastructure, so userspace does not have to special case iscsi and so userspace does not have to make a extra special case for hardware iscsi root scanning. Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-
Mike Christie authored
This has qla4xxx use the iscsi class's check ready function in the queue command function, so all iscsi drivers return the same error value for common problems. Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Cc: David Somayajulu <david.somayajulu@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-
Mike Christie authored
Qla4xxx can just call the iscsi recovery functions directly. There is no need for userspace to do this for qla4xxx, because we do not use the mutex to iterate over devices anymore and iscsi_block /unblock_session can be called from interrupt context or the dpc thread. And having userspace do this just creates uneeded headaches for qla4xxx root situations where the session may experience problems. For example during the kernel shutdown the scsi layer wants to send sync caches, but at this time userspace is not up (iscsid is not running), so we cannot recover from the problem. Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Cc: David Somayajulu <david.somayajulu@qlogic.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-
Mike Christie authored
This adds a iscsi session state file which exports the session state for both software and hardware iscsi. It also hooks libiscsi in. Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-
Boaz Harrosh authored
- convert to accessors and !use_sg cleanup Signed-off-by: Boaz Harrosh <bharrosh@panasas.com> Tested-by: Russell King <rmk@arm.linux.org.uk> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-
James Bottomley authored
This driver depends on the deprecated NCR53C9X core and needs to be converted to the esp_scsi core. Acked-by: Boaz Harrosh <bharrosh@panasas.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-
Tony Battersby authored
This patch fixes the calculation of the data transfer residual for the case of a command that is supposed to transfer an odd number of bytes on a wide bus but transfers nothing instead. Signed-off-by: Tony Battersby <tonyb@cybernetics.com> Cc: Matthew Wilcox <matthew@wil.cx> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-
Aegis Lin authored
It should be desired that 64 KiB is available for ATAPI transferrring. (Historically) in SCSI/block layer sector size is defined as 512 during sector-byte calculation. Originally in ps3rom.c CD_FRAMESIZE (2048) was used, which limited /sys/block/sr0/queue/max_sectors_kb to 16 KiB (32 sectors). Signed-off-by: Aegis Lin <aegislin@gmail.com> Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-
Thomas Bogendoerfer authored
Converted sun3x_esp driver to use esp_scsi.c Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-
Adrian Bunk authored
__iscsi_complete_pdu() can now become static. Signed-off-by: Adrian Bunk <bunk@kernel.org> Acked-by: Mike Christie <michaelc@cs.wisc.edu> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-
Salyzyn, Mark authored
The first patch (a119ee8e) was a bit too aggressive and nested the locks (!) unit testing was in error. This patch was reverted by 203a512f. This new patch should fix the locks correctly. Signed-off-by: Mark Salyzyn <aacraid@adaptec.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
-
- 07 Feb, 2008 8 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/shaggy/jfs-2.6Linus Torvalds authored
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/shaggy/jfs-2.6: BKL-removal: Implement a compat_ioctl handler for JFS BKL-removal: Use unlocked_ioctl for jfs
-
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/inputLinus Torvalds authored
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (34 commits) Input: i8042 - non-x86 build fix Input: pxa27x_keypad - also enable on PXA3xx Input: pxa27x_keypad - add debounce_interval to the keypad platform data Input: pxa27x_keypad - use device resources for I/O memory mapping and IRQ Input: pxa27x_keypad - enable rotary encoders and direct keys Input: pxa27x_keypad - introduce pxa27x_keypad_config() Input: pxa27x_keypad - introduce driver structure and use KEY() to define matrix keys Input: pxa27x_keypad - remove pin configuration from the driver Input: pxa27x_keypad - rename the driver (was pxa27x_keyboard) Input: constify function pointer tables (seq_operations) Input: i8042 - add Fujitsu-Siemens Amilo Pro 2010 to nomux list Input: i8042 - enable DMI quirks on x86-64 Input: i8042 - add Dritek quirk for Acer Aspire 9110 Input: add input event to APM event bridge Input: mousedev - use BIT_MASK instead of BIT Input: remove duplicate includes Input: remove cdev from input_dev structure Input: remove duplicated headers in drivers/char/keyboard.c Input: i8042 - add Dritek keyboard extension quirk Input: add Tosa keyboard driver ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2Linus Torvalds authored
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2: ocfs2: Negotiate locking protocol versions.
-
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-2.6Linus Torvalds authored
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-2.6: sysfs: remove BUG_ON() from sysfs_remove_group() Driver core: Revert "Fix Firmware class name collision" Block: Fix whole_disk attribute bug
-
Andi Kleen authored
The ioctls were already compatible except for the actual values so this was fairly easy to do. Signed-off-by: Andi Kleen <ak@suse.de> Signed-off-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com>
-
Jesse Barnes authored
Make sure we have enough room for all the GR registers or we'll end up clobbering the AR index register (which should actually be harmless unless the BIOS is making an assumption about it). Noticed-by: Jens Axboe <jens.axboe@oracle.com> Signed-off-by: Jesse Barnes <jesse.barnes@intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Andi Kleen authored
Convert jfs_ioctl over to not use the BKL. The only potential race I could see was with two ioctls in parallel changing the flags and losing the updates. Use the i_mutex to protect against this. Signed-off-by: Andi Kleen <ak@suse.de> Signed-off-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com>
-
Greg Kroah-Hartman authored
It's possible that the caller of sysfs_remove_group messed up and passed in an attribute group that was not really registered to this kobject. But don't panic for such a foolish error, spit out a warning about what happened, and continue on our way safely. Cc: Roland Dreier <rdreier@cisco.com> Cc: Tejun Heo <htejun@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-