- 23 Jul, 2021 4 commits
-
-
Jedrzej Jagielski authored
In SW DCB mode the packets sent receive incorrect UP tags. They are constructed correctly and put into tx_ring, but UP is later remapped by HW on the basis of TCTUPR register contents according to Tx queue selected, and BW used is consistent with the new UP values. This is caused by Tx queue selection in kernel not taking into account DCB configuration. This patch fixes the issue by implementing the ndo_select_queue NDO callback. Fixes: fd0a05ce ("i40e: transmit, receive, and NAPI") Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com> Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com> Tested-by: Imam Hassan Reza Biswas <imam.hassan.reza.biswas@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
-
Lukasz Cieplicki authored
In case of PHY type error occurs, the message was too generic. Add additional info to PHY type error indicating that it can be wrong cable connected. Fixes: 124ed15b ("i40e: Add dual speed module support") Signed-off-by: Lukasz Cieplicki <lukaszx.cieplicki@intel.com> Signed-off-by: Michal Maloszewski <michal.maloszewski@intel.com> Tested-by: Tony Brelinski <tonyx.brelinski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
-
Arkadiusz Kubalewski authored
Make warning meaningful for the user. Previously the trace: "Starting FW LLDP agent failed: error: I40E_ERR_ADMIN_QUEUE_ERROR, I40E_AQ_RC_EAGAIN" was produced when user tried to start Firmware LLDP agent, just after it was stopped with sequence: ethtool --set-priv-flags <dev> disable-fw-lldp on ethtool --set-priv-flags <dev> disable-fw-lldp off (without any delay between the commands) At that point the firmware is still processing stop command, the behavior is expected. Fixes: c1041d07 ("i40e: Missing response checks in driver when starting/stopping FW LLDP") Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com> Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com> Tested-by: Imam Hassan Reza Biswas <imam.hassan.reza.biswas@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
-
Arkadiusz Kubalewski authored
Correct the message flow between driver and firmware when disabling queues. Previously in case of PF reset (due to required reinit after reconfig), the error like: "VSI seid 397 Tx ring 60 disable timeout" could show up occasionally. The error was not a real issue of hardware or firmware, it was caused by wrong sequence of messages invoked by the driver. Fixes: 41c445ff ("i40e: main driver core") Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com> Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com> Tested-by: Tony Brelinski <tonyx.brelinski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
-
- 22 Jul, 2021 14 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linuxLinus Torvalds authored
Pull arm64 fixes from Will Deacon: "A pair of arm64 fixes for -rc3. The straightforward one is a fix to our firmware calling stub, which accidentally started corrupting the link register on machines with SVE. Since these machines don't really exist yet, it wasn't spotted in -next. The other fix is a revert-and-a-bit of a patch originally intended to allow PTE-level huge mappings for the VMAP area on 32-bit PPC 8xx. A side-effect of this change was that our pXd_set_huge() implementations could be replaced with generic dummy functions depending on the levels of page-table being used, which in turn broke the boot if we fail to create the linear mapping as a result of using these functions to operate on the pgd. Huge thanks to Michael Ellerman for modifying the revert so as not to regress PPC 8xx in terms of functionality. Anyway, that's the background and it's also available in the commit message along with Link tags pointing at all of the fun. Summary: - Fix hang when issuing SMC on SVE-capable system due to clobbered LR - Fix boot failure due to missing block mappings with folded page-table" * tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: Revert "mm/pgtable: add stubs for {pmd/pub}_{set/clear}_huge" arm64: smccc: Save lr before calling __arm_smccc_sve_check()
-
Linus Torvalds authored
Merge tag 'hyperv-fixes-signed-20210722' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux Pull hyperv fixes from Wei Liu: - bug fix from Haiyang for vmbus CPU assignment - revert of a bogus patch that went into 5.14-rc1 * tag 'hyperv-fixes-signed-20210722' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux: Revert "x86/hyperv: fix logical processor creation" Drivers: hv: vmbus: Fix duplicate CPU assignments within a device
-
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netLinus Torvalds authored
Pull networking fixes from David Miller: 1) Fix type of bind option flag in af_xdp, from Baruch Siach. 2) Fix use after free in bpf_xdp_link_release(), from Xuan Zhao. 3) PM refcnt imbakance in r8152, from Takashi Iwai. 4) Sign extension ug in liquidio, from Colin Ian King. 5) Mising range check in s390 bpf jit, from Colin Ian King. 6) Uninit value in caif_seqpkt_sendmsg(), from Ziyong Xuan. 7) Fix skb page recycling race, from Ilias Apalodimas. 8) Fix memory leak in tcindex_partial_destroy_work, from Pave Skripkin. 9) netrom timer sk refcnt issues, from Nguyen Dinh Phi. 10) Fix data races aroun tcp's tfo_active_disable_stamp, from Eric Dumazet. 11) act_skbmod should only operate on ethernet packets, from Peilin Ye. 12) Fix slab out-of-bpunds in fib6_nh_flush_exceptions(),, from Psolo Abeni. 13) Fix sparx5 dependencies, from Yajun Deng. * git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (74 commits) dpaa2-switch: seed the buffer pool after allocating the swp net: sched: cls_api: Fix the the wrong parameter net: sparx5: fix unmet dependencies warning net: dsa: tag_ksz: dont let the hardware process the layer 4 checksum net: dsa: ensure linearized SKBs in case of tail taggers ravb: Remove extra TAB ravb: Fix a typo in comment net: dsa: sja1105: make VID 4095 a bridge VLAN too tcp: disable TFO blackhole logic by default sctp: do not update transport pathmtu if SPP_PMTUD_ENABLE is not set net: ixp46x: fix ptp build failure ibmvnic: Remove the proper scrq flush selftests: net: add ESP-in-UDP PMTU test udp: check encap socket in __udp_lib_err sctp: update active_key for asoc when old key is being replaced r8169: Avoid duplicate sysfs entry creation error ixgbe: Fix packet corruption due to missing DMA sync Revert "qed: fix possible unpaired spin_{un}lock_bh in _qed_mcp_cmd_and_union()" ipv6: fix another slab-out-of-bounds in fib6_nh_flush_exceptions fsl/fman: Add fibre support ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmcLinus Torvalds authored
Pull MMC fixes from Ulf Hansson: - Use kref to fix KASAN splats triggered during card removal - Don't allocate IDA for OF aliases * tag 'mmc-v5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: mmc: core: Don't allocate IDA for OF aliases mmc: core: Use kref in place of struct mmc_blk_data::usage
-
Ioana Ciornei authored
Any interraction with the buffer pool (seeding a buffer, acquire one) is made through a software portal (SWP, a DPIO object). There are circumstances where the dpaa2-switch driver probes on a DPSW before any DPIO devices have been probed. In this case, seeding of the buffer pool will lead to a panic since no SWPs are initialized. To fix this, seed the buffer pool after making sure that the software portals have been probed and are ready to be used. Fixes: 0b1b7137 ("staging: dpaa2-switch: handle Rx path on control interface") Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Yajun Deng authored
The 4th parameter in tc_chain_notify() should be flags rather than seq. Let's change it back correctly. Fixes: 32a4f5ec ("net: sched: introduce chain object to uapi") Signed-off-by: Yajun Deng <yajun.deng@linux.dev> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Randy Dunlap authored
WARNING: unmet direct dependencies detected for PHY_SPARX5_SERDES Depends on [n]: (ARCH_SPARX5 || COMPILE_TEST [=n]) && OF [=y] && HAS_IOMEM [=y] Selected by [y]: - SPARX5_SWITCH [=y] && NETDEVICES [=y] && ETHERNET [=y] && NET_VENDOR_MICROCHIP [=y] && NET_SWITCHDEV [=y] && HAS_IOMEM [=y] && OF [=y] Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: Lars Povlsen <lars.povlsen@microchip.com> Cc: Steen Hegelund <Steen.Hegelund@microchip.com> Cc: UNGLinuxDriver@microchip.com Cc: "David S. Miller" <davem@davemloft.net> Cc: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Lino Sanfilippo says: ==================== Fixes for KSZ DSA switch These patches fix issues I encountered while using a KSZ9897 as a DSA switch with a broadcom GENET network device as the DSA master device. PATCH 1 fixes an invalid access to an SKB in case it is scattered. PATCH 2 fixes incorrect hardware checksum calculation caused by the DSA tag. Changes in v2: - instead of linearizing the SKBs only for KSZ switches ensure linearized SKBs for all tail taggers by clearing the feature flags NETIF_F_HW_SG and NETIF_F_FRAGLIST (suggested by Vladimir Oltean) The patches have been tested with a KSZ9897 and apply against net-next. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Lino Sanfilippo authored
If the checksum calculation is offloaded to the network device (e.g due to NETIF_F_HW_CSUM inherited from the DSA master device), the calculated layer 4 checksum is incorrect. This is since the DSA tag which is placed after the layer 4 data is considered as being part of the daa and thus errorneously included into the checksum calculation. To avoid this, always calculate the layer 4 checksum in software. Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Lino Sanfilippo authored
The function skb_put() that is used by tail taggers to make room for the DSA tag must only be called for linearized SKBS. However in case that the slave device inherited features like NETIF_F_HW_SG or NETIF_F_FRAGLIST the SKB passed to the slaves transmit function may not be linearized. Avoid those SKBs by clearing the NETIF_F_HW_SG and NETIF_F_FRAGLIST flags for tail taggers. Furthermore since the tagging protocol can be changed at runtime move the code for setting up the slaves features into dsa_slave_setup_tagger(). Suggested-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Biju Das authored
Align the member description comments for struct ravb_desc by removing the extra TAB. Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com> Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Biju Das authored
Fix the typo RX->TX in comment, as the code following the comment process TX and not RX. Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com> Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Vladimir Oltean authored
This simple series of commands: ip link add br0 type bridge vlan_filtering 1 ip link set swp0 master br0 fails on sja1105 with the following error: [ 33.439103] sja1105 spi0.1: vlan-lookup-table needs to have at least the default untagged VLAN [ 33.447710] sja1105 spi0.1: Invalid config, cannot upload Warning: sja1105: Failed to change VLAN Ethertype. For context, sja1105 has 3 operating modes: - SJA1105_VLAN_UNAWARE: the dsa_8021q_vlans are committed to hardware - SJA1105_VLAN_FILTERING_FULL: the bridge_vlans are committed to hardware - SJA1105_VLAN_FILTERING_BEST_EFFORT: both the dsa_8021q_vlans and the bridge_vlans are committed to hardware Swapping out a VLAN list and another in happens in sja1105_build_vlan_table(), which performs a delta update procedure. That function is called from a few places, notably from sja1105_vlan_filtering() which is called from the SWITCHDEV_ATTR_ID_BRIDGE_VLAN_FILTERING handler. The above set of 2 commands fails when run on a kernel pre-commit 8841f6e6 ("net: dsa: sja1105: make devlink property best_effort_vlan_filtering true by default"). So the priv->vlan_state transition that takes place is between VLAN-unaware and full VLAN filtering. So the dsa_8021q_vlans are swapped out and the bridge_vlans are swapped in. So why does it fail? Well, the bridge driver, through nbp_vlan_init(), first sets up the SWITCHDEV_ATTR_ID_BRIDGE_VLAN_FILTERING attribute, and only then proceeds to call nbp_vlan_add for the default_pvid. So when we swap out the dsa_8021q_vlans and swap in the bridge_vlans in the SWITCHDEV_ATTR_ID_BRIDGE_VLAN_FILTERING handler, there are no bridge VLANs (yet). So we have wiped the VLAN table clean, and the low-level static config checker complains of an invalid configuration. We _will_ add the bridge VLANs using the dynamic config interface, albeit later, when nbp_vlan_add() calls us. So it is natural that it fails. So why did it ever work? Surprisingly, it looks like I only tested this configuration with 2 things set up in a particular way: - a network manager that brings all ports up - a kernel with CONFIG_VLAN_8021Q=y It is widely known that commit ad1afb00 ("vlan_dev: VLAN 0 should be treated as "no vlan tag" (802.1p packet)") installs VID 0 to every net device that comes up. DSA treats these VLANs as bridge VLANs, and therefore, in my testing, the list of bridge_vlans was never empty. However, if CONFIG_VLAN_8021Q is not enabled, or the port is not up when it joins a VLAN-aware bridge, the bridge_vlans list will be temporarily empty, and the sja1105_static_config_reload() call from sja1105_vlan_filtering() will fail. To fix this, the simplest thing is to keep VID 4095, the one used for CPU-injected control packets since commit ed040abc ("net: dsa: sja1105: use 4095 as the private VLAN for untagged traffic"), in the list of bridge VLANs too, not just the list of tag_8021q VLANs. This ensures that the list of bridge VLANs will never be empty. Fixes: ec5ae610 ("net: dsa: sja1105: save/restore VLANs using a delta commit method") Reported-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Wei Wang authored
Multiple complaints have been raised from the TFO users on the internet stating that the TFO blackhole logic is too aggressive and gets falsely triggered too often. (e.g. https://blog.apnic.net/2021/07/05/tcp-fast-open-not-so-fast/) Considering that most middleboxes no longer drop TFO packets, we decide to disable the blackhole logic by setting /proc/sys/net/ipv4/tcp_fastopen_blackhole_timeout_set to 0 by default. Fixes: cf1ef3f0 ("net/tcp_fastopen: Disable active side TFO in certain scenarios") Signed-off-by: Wei Wang <weiwan@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Acked-by: Yuchung Cheng <ycheng@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
- 21 Jul, 2021 19 commits
-
-
Xin Long authored
Currently, in sctp_packet_config(), sctp_transport_pmtu_check() is called to update transport pathmtu with dst's mtu when dst's mtu has been changed by non sctp stack like xfrm. However, this should only happen when SPP_PMTUD_ENABLE is set, no matter where dst's mtu changed. This patch is to fix by checking SPP_PMTUD_ENABLE flag before calling sctp_transport_pmtu_check(). Thanks Jacek for reporting and looking into this issue. v1->v2: - add the missing "{" to fix the build error. Fixes: 69fec325 ('Revert "sctp: remove sctp_transport_pmtu_check"') Reported-by: Jacek Szafraniec <jacek.szafraniec@nokia.com> Tested-by: Jacek Szafraniec <jacek.szafraniec@nokia.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linuxLinus Torvalds authored
Pull s390 updates from Heiko Carstens: - fix / add expoline usage in "DMA" code - fix compat vdso Makefile to avoid permanent rebuild - fix ftrace_update_ftrace_func to avoid NULL pointer dereference - update defconfigs - trivial coding style fix * tag 's390-5.14-3' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: s390: update defconfigs s390/cpumf: fix semicolon.cocci warnings s390/boot: fix use of expolines in the DMA code s390/ftrace: fix ftrace_update_ftrace_func implementation s390/defconfig: allow early device mapper disks s390/vdso32: add vdso32.lds to targets
-
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spiLinus Torvalds authored
Pull spi fixes from Mark Brown: "A collection of driver specific fixes, there was a bit of a kerfuffle with some last minute review on hte spi-cadence-quadspi division by zero change but otherwise nothing terribly remarkable here - important fixes if you have the hardware but nothing with too wide an impact" * tag 'spi-fix-v5.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: spi: spi-bcm2835: Fix deadlock spi: cadence: Correct initialisation of runtime PM again spi: cadence-quadspi: Disable Auto-HW polling spi: spi-cadence-quadspi: Fix division by zero warning spi: spi-cadence-quadspi: Revert "Fix division by zero warning" spi: spi-cadence-quadspi: Fix division by zero warning spi: mediatek: move devm_spi_register_master position spi: mediatek: fix fifo rx mode spi: atmel: Fix CS and initialization bug spi: stm32: fixes pm_runtime calls in probe/remove spi: imx: mx51-ecspi: Reinstate low-speed CONFIGREG delay spi: stm32h7: fix full duplex irq handler handling
-
Linus Torvalds authored
Merge tag 'regulator-fix-v5.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator Pull regulator fixes from Mark Brown: "A few driver specific fixes that came in since the merge window, plus a change to mark the regulator-fixed-domain DT binding as deprecated in order to try to to discourage any new users while a better solution is put in place" * tag 'regulator-fix-v5.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: regulator: hi6421: Fix getting wrong drvdata regulator: mtk-dvfsrc: Fix wrong dev pointer for devm_regulator_register regulator: fixed: Mark regulator-fixed-domain as deprecated regulator: bd9576: Fix testing wrong flag in check_temp_flag_mismatch regulator: hi6421v600: Fix getting wrong drvdata that causes boot failure regulator: rt5033: Fix n_voltages settings for BUCK and LDO regulator: rtmv20: Fix wrong mask for strobe-polarity-high
-
git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fsLinus Torvalds authored
Pull AFS fixes from David Howells: - Fix a tracepoint that causes one of the tracing subsystem query files to crash if the module is loaded - Fix afs_writepages() to take account of whether the storage rpc actually succeeded when updating the cyclic writeback counter - Fix some error code propagation/handling - Fix place where afs_writepages() was setting writeback_index to a file position rather than a page index * tag 'afs-fixes-20210721' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs: afs: Remove redundant assignment to ret afs: Fix setting of writeback_index afs: check function return afs: Fix tracepoint string placement with built-in AFS
-
Arnd Bergmann authored
The rework of the ixp46x cpu detection left the network driver in a half broken state: drivers/net/ethernet/xscale/ptp_ixp46x.c: In function 'ptp_ixp_init': drivers/net/ethernet/xscale/ptp_ixp46x.c:290:51: error: 'IXP4XX_TIMESYNC_BASE_VIRT' undeclared (first use in this function) 290 | (struct ixp46x_ts_regs __iomem *) IXP4XX_TIMESYNC_BASE_VIRT; | ^~~~~~~~~~~~~~~~~~~~~~~~~ drivers/net/ethernet/xscale/ptp_ixp46x.c:290:51: note: each undeclared identifier is reported only once for each function it appears in drivers/net/ethernet/xscale/ptp_ixp46x.c: At top level: drivers/net/ethernet/xscale/ptp_ixp46x.c:323:1: error: data definition has no type or storage class [-Werror] 323 | module_init(ptp_ixp_init); I have patches to complete the transition for a future release, but for the moment, add the missing include statements to get it to build again. Fixes: 09aa9aab ("soc: ixp4xx: move cpu detection to linux/soc/ixp4xx/cpu.h") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Sukadev Bhattiprolu authored
Commit 65d6470d ("ibmvnic: clean pending indirect buffs during reset") intended to remove the call to ibmvnic_tx_scrq_flush() when the ->resetting flag is true and was tested that way. But during the final rebase to net-next, the hunk got applied to a block few lines below (which happened to have the same diff context) and the wrong call to ibmvnic_tx_scrq_flush() got removed. Fix that by removing the correct ibmvnic_tx_scrq_flush() and restoring the one that was incorrectly removed. Fixes: 65d6470d ("ibmvnic: clean pending indirect buffs during reset") Reported-by: Dany Madden <drt@linux.ibm.com> Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Wei Liu authored
This reverts commit 450605c2. Signed-off-by: Wei Liu <wei.liu@kernel.org>
-
David S. Miller authored
Vadim Fedorenko ays: ==================== Fix PMTU for ESP-in-UDP encapsulation Bug 213669 uncovered regression in PMTU discovery for UDP-encapsulated routes and some incorrect usage in udp tunnel fields. This series fixes problems and also adds such case for selftests v3: - update checking logic to account SCTP use case v2: - remove refactor code that was in first patch - move checking logic to __udp{4,6}_lib_err_encap - add more tests, especially routed configuration ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
-
Vadim Fedorenko authored
The case of ESP in UDP encapsulation was not covered before. Add cases of local changes of MTU and difference on routed path. Signed-off-by: Vadim Fedorenko <vfedorenko@novek.ru> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Vadim Fedorenko authored
Commit d26796ae ("udp: check udp sock encap_type in __udp_lib_err") added checks for encapsulated sockets but it broke cases when there is no implementation of encap_err_lookup for encapsulation, i.e. ESP in UDP encapsulation. Fix it by calling encap_err_lookup only if socket implements this method otherwise treat it as legal socket. Fixes: d26796ae ("udp: check udp sock encap_type in __udp_lib_err") Signed-off-by: Vadim Fedorenko <vfedorenko@novek.ru> Reviewed-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Xin Long authored
syzbot reported a call trace: BUG: KASAN: use-after-free in sctp_auth_shkey_hold+0x22/0xa0 net/sctp/auth.c:112 Call Trace: sctp_auth_shkey_hold+0x22/0xa0 net/sctp/auth.c:112 sctp_set_owner_w net/sctp/socket.c:131 [inline] sctp_sendmsg_to_asoc+0x152e/0x2180 net/sctp/socket.c:1865 sctp_sendmsg+0x103b/0x1d30 net/sctp/socket.c:2027 inet_sendmsg+0x99/0xe0 net/ipv4/af_inet.c:821 sock_sendmsg_nosec net/socket.c:703 [inline] sock_sendmsg+0xcf/0x120 net/socket.c:723 This is an use-after-free issue caused by not updating asoc->shkey after it was replaced in the key list asoc->endpoint_shared_keys, and the old key was freed. This patch is to fix by also updating active_key for asoc when old key is being replaced with a new one. Note that this issue doesn't exist in sctp_auth_del_key_id(), as it's not allowed to delete the active_key from the asoc. Fixes: 1b1e0bc9 ("sctp: add refcnt support for sh_key") Reported-by: syzbot+b774577370208727d12b@syzkaller.appspotmail.com Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Sayanta Pattanayak authored
When registering the MDIO bus for a r8169 device, we use the PCI bus/device specifier as a (seemingly) unique device identifier. However the very same BDF number can be used on another PCI segment, which makes the driver fail probing: [ 27.544136] r8169 0002:07:00.0: enabling device (0000 -> 0003) [ 27.559734] sysfs: cannot create duplicate filename '/class/mdio_bus/r8169-700' .... [ 27.684858] libphy: mii_bus r8169-700 failed to register [ 27.695602] r8169: probe of 0002:07:00.0 failed with error -22 Add the segment number to the device name to make it more unique. This fixes operation on ARM N1SDP boards, with two boards connected together to form an SMP system, and all on-board devices showing up twice, just on different PCI segments. A similar issue would occur on large systems with many PCI slots and multiple RTL8169 NICs. Fixes: f1e911d5 ("r8169: add basic phylib support") Signed-off-by: Sayanta Pattanayak <sayanta.pattanayak@arm.com> [Andre: expand commit message, use pci_domain_nr()] Signed-off-by: Andre Przywara <andre.przywara@arm.com> Acked-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Jiapeng Chong authored
Variable ret is set to -ENOENT and -ENOMEM but this value is never read as it is overwritten or not used later on, hence it is a redundant assignment and can be removed. Cleans up the following clang-analyzer warning: fs/afs/dir.c:2014:4: warning: Value stored to 'ret' is never read [clang-analyzer-deadcode.DeadStores]. fs/afs/dir.c:659:2: warning: Value stored to 'ret' is never read [clang-analyzer-deadcode.DeadStores]. [DH made the following modifications: - In afs_rename(), -ENOMEM should be placed in op->error instead of ret, rather than the assignment being removed entirely. afs_put_operation() will pick it up from there and return it. - If afs_sillyrename() fails, its error code should be placed in op->error rather than in ret also. ] Fixes: e49c7b2f ("afs: Build an abstraction around an "operation" concept") Reported-by: Abaci Robot <abaci@linux.alibaba.com> Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com> Signed-off-by: David Howells <dhowells@redhat.com> Reviewed-by: Marc Dionne <marc.dionne@auristor.com> cc: linux-afs@lists.infradead.org Link: https://lore.kernel.org/r/1619691492-83866-1-git-send-email-jiapeng.chong@linux.alibaba.com Link: https://lore.kernel.org/r/162609465444.3133237.7562832521724298900.stgit@warthog.procyon.org.uk/ # v1 Link: https://lore.kernel.org/r/162610729052.3408253.17364333638838151299.stgit@warthog.procyon.org.uk/ # v2
-
David Howells authored
Fix afs_writepages() to always set mapping->writeback_index to a page index and not a byte position[1]. Fixes: 31143d5d ("AFS: implement basic file write support") Reported-by: Marc Dionne <marc.dionne@auristor.com> Signed-off-by: David Howells <dhowells@redhat.com> Reviewed-by: Marc Dionne <marc.dionne@auristor.com> cc: linux-afs@lists.infradead.org Link: https://lore.kernel.org/r/CAB9dFdvHsLsw7CMnB+4cgciWDSqVjuij4mH3TaXnHQB8sz5rHw@mail.gmail.com/ [1] Link: https://lore.kernel.org/r/162610728339.3408253.4604750166391496546.stgit@warthog.procyon.org.uk/ # v2 (no v1)
-
Tom Rix authored
Static analysis reports this problem write.c:773:29: warning: Assigned value is garbage or undefined mapping->writeback_index = next; ^ ~~~~ The call to afs_writepages_region() can return without setting next. So check the function return before using next. Changes: ver #2: - Need to fix the range_cyclic case also[1]. Fixes: e87b03f5 ("afs: Prepare for use of THPs") Signed-off-by: Tom Rix <trix@redhat.com> Signed-off-by: David Howells <dhowells@redhat.com> Reviewed-by: Marc Dionne <marc.dionne@auristor.com> cc: linux-afs@lists.infradead.org Link: https://lore.kernel.org/r/20210430155031.3287870-1-trix@redhat.com Link: https://lore.kernel.org/r/CAB9dFdvHsLsw7CMnB+4cgciWDSqVjuij4mH3TaXnHQB8sz5rHw@mail.gmail.com/ [1] Link: https://lore.kernel.org/r/162609464716.3133237.10354897554363093252.stgit@warthog.procyon.org.uk/ # v1 Link: https://lore.kernel.org/r/162610727640.3408253.8687445613469681311.stgit@warthog.procyon.org.uk/ # v2
-
David Howells authored
To quote Alexey[1]: I was adding custom tracepoint to the kernel, grabbed full F34 kernel .config, disabled modules and booted whole shebang as VM kernel. Then did perf record -a -e ... It crashed: general protection fault, probably for non-canonical address 0x435f5346592e4243: 0000 [#1] SMP PTI CPU: 1 PID: 842 Comm: cat Not tainted 5.12.6+ #26 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.14.0-1.fc33 04/01/2014 RIP: 0010:t_show+0x22/0xd0 Then reproducer was narrowed to # cat /sys/kernel/tracing/printk_formats Original F34 kernel with modules didn't crash. So I started to disable options and after disabling AFS everything started working again. The root cause is that AFS was placing char arrays content into a section full of _pointers_ to strings with predictable consequences. Non canonical address 435f5346592e4243 is "CB.YFS_" which came from CM_NAME macro. Steps to reproduce: CONFIG_AFS=y CONFIG_TRACING=y # cat /sys/kernel/tracing/printk_formats Fix this by the following means: (1) Add enum->string translation tables in the event header with the AFS and YFS cache/callback manager operations listed by RPC operation ID. (2) Modify the afs_cb_call tracepoint to print the string from the translation table rather than using the string at the afs_call name pointer. (3) Switch translation table depending on the service we're being accessed as (AFS or YFS) in the tracepoint print clause. Will this cause problems to userspace utilities? Note that the symbolic representation of the YFS service ID isn't available to this header, so I've put it in as a number. I'm not sure if this is the best way to do this. (4) Remove the name wrangling (CM_NAME) macro and put the names directly into the afs_call_type structs in cmservice.c. Fixes: 8e8d7f13 ("afs: Add some tracepoints") Reported-by: Alexey Dobriyan (SK hynix) <adobriyan@gmail.com> Signed-off-by: David Howells <dhowells@redhat.com> Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Reviewed-by: Marc Dionne <marc.dionne@auristor.com> cc: Andrew Morton <akpm@linux-foundation.org> cc: linux-afs@lists.infradead.org Link: https://lore.kernel.org/r/YLAXfvZ+rObEOdc%2F@localhost.localdomain/ [1] Link: https://lore.kernel.org/r/643721.1623754699@warthog.procyon.org.uk/ Link: https://lore.kernel.org/r/162430903582.2896199.6098150063997983353.stgit@warthog.procyon.org.uk/ # v1 Link: https://lore.kernel.org/r/162609463957.3133237.15916579353149746363.stgit@warthog.procyon.org.uk/ # v1 (repost) Link: https://lore.kernel.org/r/162610726860.3408253.445207609466288531.stgit@warthog.procyon.org.uk/ # v2
-
Jonathan Marek authored
This reverts commit c742199a. c742199a ("mm/pgtable: add stubs for {pmd/pub}_{set/clear}_huge") breaks arm64 in at least two ways for configurations where PUD or PMD folding occur: 1. We no longer install huge-vmap mappings and silently fall back to page-granular entries, despite being able to install block entries at what is effectively the PGD level. 2. If the linear map is backed with block mappings, these will now silently fail to be created in alloc_init_pud(), causing a panic early during boot. The pgtable selftests caught this, although a fix has not been forthcoming and Christophe is AWOL at the moment, so just revert the change for now to get a working -rc3 on which we can queue patches for 5.15. A simple revert breaks the build for 32-bit PowerPC 8xx machines, which rely on the default function definitions when the corresponding page-table levels are folded, since commit a6a8f7c4 ("powerpc/8xx: add support for huge pages on VMAP and VMALLOC"), eg: powerpc64-linux-ld: mm/vmalloc.o: in function `vunmap_pud_range': linux/mm/vmalloc.c:362: undefined reference to `pud_clear_huge' To avoid that, add stubs for pud_clear_huge() and pmd_clear_huge() in arch/powerpc/mm/nohash/8xx.c as suggested by Christophe. Cc: Christophe Leroy <christophe.leroy@csgroup.eu> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Nicholas Piggin <npiggin@gmail.com> Cc: Mike Rapoport <rppt@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Fixes: c742199a ("mm/pgtable: add stubs for {pmd/pub}_{set/clear}_huge") Signed-off-by: Jonathan Marek <jonathan@marek.ca> Reviewed-by: Ard Biesheuvel <ardb@kernel.org> Acked-by: Marc Zyngier <maz@kernel.org> [mpe: Fold in 8xx.c changes from Christophe and mention in change log] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/linux-arm-kernel/CAMuHMdXShORDox-xxaeUfDW3wx2PeggFSqhVSHVZNKCGK-y_vQ@mail.gmail.com/ Link: https://lore.kernel.org/r/20210717160118.9855-1-jonathan@marek.ca Link: https://lore.kernel.org/r/87r1fs1762.fsf@mpe.ellerman.id.auSigned-off-by: Will Deacon <will@kernel.org>
-
Jean-Philippe Brucker authored
Commit cfa7ff95 ("arm64: smccc: Support SMCCC v1.3 SVE register saving hint") added a call to __arm_smccc_sve_check() which clobbers the lr (register x30), causing __arm_smccc_hvc() to return to itself and crash. Save lr on the stack before calling __arm_smccc_sve_check(). Save the frame pointer (x29) to complete the frame record, and adjust the offsets used to access stack parameters. Acked-by: Ard Biesheuvel <ardb@kernel.org> Acked-by: Mark Brown <broonie@kernel.org> Fixes: cfa7ff95 ("arm64: smccc: Support SMCCC v1.3 SVE register saving hint") Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org> Link: https://lore.kernel.org/r/20210721071834.69130-1-jean-philippe@linaro.orgSigned-off-by: Will Deacon <will@kernel.org>
-
- 20 Jul, 2021 3 commits
-
-
Markus Boehme authored
When receiving a packet with multiple fragments, hardware may still touch the first fragment until the entire packet has been received. The driver therefore keeps the first fragment mapped for DMA until end of packet has been asserted, and delays its dma_sync call until then. The driver tries to fit multiple receive buffers on one page. When using 3K receive buffers (e.g. using Jumbo frames and legacy-rx is turned off/build_skb is being used) on an architecture with 4K pages, the driver allocates an order 1 compound page and uses one page per receive buffer. To determine the correct offset for a delayed DMA sync of the first fragment of a multi-fragment packet, the driver then cannot just use PAGE_MASK on the DMA address but has to construct a mask based on the actual size of the backing page. Using PAGE_MASK in the 3K RX buffer/4K page architecture configuration will always sync the first page of a compound page. With the SWIOTLB enabled this can lead to corrupted packets (zeroed out first fragment, re-used garbage from another packet) and various consequences, such as slow/stalling data transfers and connection resets. For example, testing on a link with MTU exceeding 3058 bytes on a host with SWIOTLB enabled (e.g. "iommu=soft swiotlb=262144,force") TCP transfers quickly fizzle out without this patch. Cc: stable@vger.kernel.org Fixes: 0c5661ec ("ixgbe: fix crash in build_skb Rx code path") Signed-off-by: Markus Boehme <markubo@amazon.com> Tested-by: Tony Brelinski <tonyx.brelinski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Heiko Carstens authored
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
-
kernel test robot authored
arch/s390/kernel/perf_cpum_cf.c:748:2-3: Unneeded semicolon Remove unneeded semicolon. Generated by: scripts/coccinelle/misc/semicolon.cocci Fixes: a029a4ea ("s390/cpumf: Allow concurrent access for CPU Measurement Counter Facility") CC: Thomas Richter <tmricht@linux.ibm.com> Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: kernel test robot <lkp@intel.com> Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
-