- 31 Dec, 2015 7 commits
-
-
Stefan Bader authored
Added a safeguard in the shutdown case. At least while not being attached it is also possible to trigger a kernel bug by writing into writeback_running. This change adds the same check before trying to wake up the thread for that case. Signed-off-by:
Stefan Bader <stefan.bader@canonical.com> Cc: Kent Overstreet <kent.overstreet@gmail.com> Cc: stable@vger.kernel.org Signed-off-by:
Jens Axboe <axboe@fb.com>
-
Gabriel de Perthuis authored
Allows to use register, not register_quiet in udev to avoid "device_busy" error. The initial patch proposed at https://lkml.org/lkml/2013/8/26/549 by Gabriel de Perthuis <g2p.code@gmail.com> does not unlock the mutex and hangs the kernel. See http://thread.gmane.org/gmane.linux.kernel.bcache.devel/2594 for the discussion. Cc: Denis Bychkov <manover@gmail.com> Cc: Kent Overstreet <kent.overstreet@gmail.com> Cc: Eric Wheeler <bcache@linux.ewheeler.net> Cc: Gabriel de Perthuis <g2p.code@gmail.com> Cc: stable@vger.kernel.org Signed-off-by:
-
Zheng Liu authored
In bcache_init() function it forgot to unregister reboot notifier if bcache fails to unregister a block device. This commit fixes this. Signed-off-by:
Zheng Liu <wenqing.lz@taobao.com> Tested-by:
Joshua Schmid <jschmid@suse.com> Tested-by:
Eric Wheeler <bcache@linux.ewheeler.net> Cc: Kent Overstreet <kmo@daterainc.com> Cc: stable@vger.kernel.org Signed-off-by:
-
Al Viro authored
Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> Tested-by:
-
Zheng Liu authored
This bug can be reproduced by the following script: #!/bin/bash bcache_sysfs="/sys/fs/bcache" function clear_cache() { if [ ! -e $bcache_sysfs ]; then echo "no bcache sysfs" exit fi cset_uuid=$(ls -l $bcache_sysfs|head -n 2|tail -n 1|awk '{print $9}') sudo sh -c "echo $cset_uuid > /sys/block/sdb/sdb1/bcache/detach" sleep 5 sudo sh -c "echo $cset_uuid > /sys/block/sdb/sdb1/bcache/attach" } for ((i=0;i<10;i++)); do clear_cache done The warning messages look like below: [ 275.948611] ------------[ cut here ]------------ [ 275.963840] WARNING: at fs/sysfs/dir.c:512 sysfs_add_one+0xb8/0xd0() (Tainted: P W --------------- ) [ 275.979253] Hardware name: Tecal RH2285 [ 275.994106] sysfs: cannot create duplicate filename '/devices/pci0000:00/0000:00:09.0/0000:08:00.0/host4/target4:2:1/4:2:1:0/block/sdb/sdb1/bcache/cache' [ 276.024105] Modules linked in: bcache tcp_diag inet_diag ipmi_devintf ipmi_si ipmi_msghandler bonding 8021q garp stp llc ipv6 ext3 jbd loop sg iomemory_vsl(P) bnx2 microcode serio_raw i2c_i801 i2c_core iTCO_wdt iTCO_vendor_support i7core_edac edac_core shpchp ext4 jbd2 mbcache megaraid_sas pata_acpi ata_generic ata_piix dm_mod [last unloaded: scsi_wait_scan] [ 276.072643] Pid: 2765, comm: sh Tainted: P W --------------- 2.6.32 #1 [ 276.089315] Call Trace: [ 276.105801] [<ffffffff81070fe7>] ? warn_slowpath_common+0x87/0xc0 [ 276.122650] [<ffffffff810710d6>] ? warn_slowpath_fmt+0x46/0x50 [ 276.139361] [<ffffffff81205c08>] ? sysfs_add_one+0xb8/0xd0 [ 276.156012] [<ffffffff8120609b>] ? sysfs_do_create_link+0x12b/0x170 [ 276.172682] [<ffffffff81206113>] ? sysfs_create_link+0x13/0x20 [ 276.189282] [<ffffffffa03bda21>] ? bcache_device_link+0xc1/0x110 [bcache] [ 276.205993] [<ffffffffa03bfa08>] ? bch_cached_dev_attach+0x478/0x4f0 [bcache] [ 276.222794] [<ffffffffa03c4a17>] ? bch_cached_dev_store+0x627/0x780 [bcache] [ 276.239680] [<ffffffff8116783a>] ? alloc_pages_current+0xaa/0x110 [ 276.256594] [<ffffffff81203b15>] ? sysfs_write_file+0xe5/0x170 [ 276.273364] [<ffffffff811887b8>] ? vfs_write+0xb8/0x1a0 [ 276.290133] [<ffffffff811890b1>] ? sys_write+0x51/0x90 [ 276.306368] [<ffffffff8100c072>] ? system_call_fastpath+0x16/0x1b [ 276.322301] ---[ end trace 9f5d4fcdd0c3edfb ]--- [ 276.338241] ------------[ cut here ]------------ [ 276.354109] WARNING: at /home/wenqing.lz/bcache/bcache/super.c:720 bcache_device_link+0xdf/0x110 [bcache]() (Tainted: P W --------------- ) [ 276.386017] Hardware name: Tecal RH2285 [ 276.401430] Couldn't create device <-> cache set symlinks [ 276.401759] Modules linked in: bcache tcp_diag inet_diag ipmi_devintf ipmi_si ipmi_msghandler bonding 8021q garp stp llc ipv6 ext3 jbd loop sg iomemory_vsl(P) bnx2 microcode serio_raw i2c_i801 i2c_core iTCO_wdt iTCO_vendor_support i7core_edac edac_core shpchp ext4 jbd2 mbcache megaraid_sas pata_acpi ata_generic ata_piix dm_mod [last unloaded: scsi_wait_scan] [ 276.465477] Pid: 2765, comm: sh Tainted: P W --------------- 2.6.32 #1 [ 276.482169] Call Trace: [ 276.498610] [<ffffffff81070fe7>] ? warn_slowpath_common+0x87/0xc0 [ 276.515405] [<ffffffff810710d6>] ? warn_slowpath_fmt+0x46/0x50 [ 276.532059] [<ffffffffa03bda3f>] ? bcache_device_link+0xdf/0x110 [bcache] [ 276.548808] [<ffffffffa03bfa08>] ? bch_cached_dev_attach+0x478/0x4f0 [bcache] [ 276.565569] [<ffffffffa03c4a17>] ? bch_cached_dev_store+0x627/0x780 [bcache] [ 276.582418] [<ffffffff8116783a>] ? alloc_pages_current+0xaa/0x110 [ 276.599341] [<ffffffff81203b15>] ? sysfs_write_file+0xe5/0x170 [ 276.616142] [<ffffffff811887b8>] ? vfs_write+0xb8/0x1a0 [ 276.632607] [<ffffffff811890b1>] ? sys_write+0x51/0x90 [ 276.648671] [<ffffffff8100c072>] ? system_call_fastpath+0x16/0x1b [ 276.664756] ---[ end trace 9f5d4fcdd0c3edfc ]--- We forget to clear BCACHE_DEV_UNLINK_DONE flag in bcache_device_attach() function when we attach a backing device first time. After detaching this backing device, this flag will be true and sysfs_remove_link() isn't called in bcache_device_unlink(). Then when we attach this backing device again, sysfs_create_link() will return EEXIST error in bcache_device_link(). So the fix is trival and we clear this flag in bcache_device_link(). Signed-off-by: -
Kent Overstreet authored
Signed-off-by:
Takashi Iwai <tiwai@suse.de> Tested-by:
-
Zheng Liu authored
Subject : [PATCH v2] bcache: fix a livelock in btree lock Date : Wed, 25 Feb 2015 20:32:09 +0800 (02/25/2015 04:32:09 AM) This commit tries to fix a livelock in bcache. This livelock might happen when we causes a huge number of cache misses simultaneously. When we get a cache miss, bcache will execute the following path. ->cached_dev_make_request() ->cached_dev_read() ->cached_lookup() ->bch->btree_map_keys() ->btree_root() <------------------------ ->bch_btree_map_keys_recurse() | ->cache_lookup_fn() | ->cached_dev_cache_miss() | ->bch_btree_insert_check_key() -| [If btree->seq is not equal to seq + 1, we should return EINTR and traverse btree again.] In bch_btree_insert_check_key() function we first need to check upgrade flag (op->lock == -1), and when this flag is true we need to release read btree->lock and try to take write btree->lock. During taking and releasing this write lock, btree->seq will be monotone increased in order to prevent other threads modify this in cache miss (see btree.h:74). But if there are some cache misses caused by some requested, we could meet a livelock because btree->seq is always changed by others. Thus no one can make progress. This commit will try to take write btree->lock if it encounters a race when we traverse btree. Although it sacrifice the scalability but we can ensure that only one can modify the btree. Signed-off-by:
-
- 23 Dec, 2015 1 commit
-
-
Jens Axboe authored
Commit 8182503d used monotonic time, but if the adapter is using the seconds for logging entries, then we'll get duplicate entries if the system is rebooted. Use real time instead. Reported-by:
Arnd Bergmann <arnd@arndb.de> Fixes: 8182503d ("block: sx8.c: Replace timeval with ktime_t") Signed-off-by:
-
- 22 Dec, 2015 1 commit
-
-
Shraddha Barke authored
32-bit systems using 'struct timeval' will break in the year 2038, in order to avoid that replace the code with more appropriate types. This patch replaces timeval with 64 bit ktime_t which is y2038 safe. Since st->timestamp is only interested in seconds, directly using time64_t here. Function ktime_get_seconds is used since it uses monotonic instead of real time and thus will not cause overflow. Signed-off-by:
Shraddha Barke <shraddha.6596@gmail.com> Signed-off-by:
-
- 25 Nov, 2015 31 commits
-
-
Lars Ellenberg authored
In case the lower level device size changed, but some other internal details of the resize did not work out, drbd_determine_dev_size() would try to restore the previous settings, trusting drbd_md_set_sector_offsets() to "do the right thing", but overlooked that this internally may set the meta data base offset based on device size. This could end up with incomplete on-disk meta data layout change, and ultimately lead to data corruption (if the failure was not noticed or ignored by the operator, and other things go wrong as well). Just remember all meta data related offsets/sizes, and on error restore them all. Signed-off-by:
Philipp Reisner <philipp.reisner@linbit.com> Signed-off-by:
Lars Ellenberg <lars.ellenberg@linbit.com> Signed-off-by:
-
Lars Ellenberg authored
During handshake communication, we also reconsider our device size, using drbd_determine_dev_size(). Just in case we need to change the offsets or layout of our on-disk metadata, we lock out application and other meta data IO, and wait for the activity log to be "idle" (no more referenced extents). If this handshake happens just after a connection loss, with a fencing policy of "resource-and-stonith", we have frozen IO. If, additionally, the activity log was "starving" (too many incoming random writes at that point in time), it won't become idle, ever, because of the frozen IO, and this would be a lockup of the receiver thread, and consquentially of DRBD. Previous logic (re-)initialized with a special "empty" transaction block, which required the activity log to fully drain first. Instead, write out some standard activity log transactions. Using lc_try_lock_for_transaction() instead of lc_try_lock() does not care about pending activity log references, avoiding the potential deadlock. Signed-off-by:
-
Lars Ellenberg authored
To be able to "force out" an activity log transaction, even if there are no pending updates. This will be used to relocate the on-disk activity log, if the on-disk offsets have to be changed, without the need to empty the activity log first. While at it, move the definition, so we can drop the forward declaration of a static helper. Signed-off-by:
-
Philipp Reisner authored
Avoid to prematurely resume application IO: don't set/clear a single bit, but inc/dec an atomic counter. Signed-off-by:
-
Lars Ellenberg authored
Don't remember a DRBD request as ack_pending, if it is not. In protocol A, we usually clear RQ_NET_PENDING at the same time we set RQ_NET_SENT, so when deciding to remember it as ack_pending, mod_rq_state needs to look at the current request state, not at the previous state before the current modification was applied. This should prevent advance_conn_req_ack_pending() from walking the full transfer log just to find NULL in protocol A, which would cause serious performance degradation with many "in-flight" requests, e.g. when working via DRBD-proxy, or with a huge bandwidth-delay product. Signed-off-by:
-
Oleg Drokin authored
new_disk_conf could be leaked if the follow on checks fail, so make sure to free it on error if it was not assigned yet. Found with smatch. Signed-off-by:
Oleg Drokin <green@linuxhacker.ru> Signed-off-by:
-
Lars Ellenberg authored
Disconnect should wait for pending bitmap IO. But if that bitmap IO is not happening, because it is waiting for pending application IO, and there is no progress, because the fencing policy suspended application IO because of the disconnect, then we deadlock. The bitmap writeout in this case does not care for concurrent application IO, so there is no point waiting for it. Signed-off-by:
-
Roland Kammerer authored
Fix the semantic of lc_seq_printf. Currently, it always returns 0 and the return value is unused, therefore, convert the return type to void. Signed-off-by:
-
Lars Ellenberg authored
lsblk should be able to pick up stacking device driver relations involving DRBD conveniently. Even though upstream kernel since 2011 says "DON'T USE THIS UNLESS YOU'RE ALREADY USING IT." a new user has been added since (bcache), which sets the precedences for us to use it as well. Signed-off-by:
-
Lars Ellenberg authored
We cannot possibly support SECDISCARD, even if all backend devices would support it: if our peer is currently unreachable, some instance of the data may obviously still be recoverable. We did not set discard_granularity at all. We don't really care (yet), we only pass them on, so for now, set our granularity to one sector. blkdev_stack_limits() takes care of the rest. If we decide we cannot support discards, not only clear the (not user visible) QUEUE_FLAG_DISCARD, but set both (user visible) discard_granularity and max_discard_sectors to zero, to avoid confusion with e.g. lsblk -D. Signed-off-by:
-
Lars Ellenberg authored
When accessing out meta data area on disk, we double check the plausibility of the requested sector offsets, and are very noisy about it if they look suspicious. During initial read of our "superblock", for "external" meta data, this triggered because the range estimate returned by drbd_md_last_sector() was still wrong. Signed-off-by:
-
Lars Ellenberg authored
Suggested by Akinobu Mita <akinobu.mita@gmail.com> Signed-off-by:
-
Lars Ellenberg authored
Apparently we now implicitly get definitions for BITS_PER_PAGE and BITS_PER_PAGE_MASK from the pid_namespace.h Instead of renaming our defines, I chose to define only if not yet defined, but to double check the value if already defined. Signed-off-by:
-
Lars Ellenberg authored
Since kernel 3.3, we can use snprintf-style arguments to create a workqueue. Signed-off-by:
-
Lars Ellenberg authored
The effective data generation ID may be interesting for debugging purposes of scenarios involving diskless states. Signed-off-by:
-
Lars Ellenberg authored
In a multiple error scenario, we may end up with a "frozen" Primary, that has no access to any data (no local disk, no replication link). If we then resume-io, we try to generate a new data generation id, which will fail if there is no longer a local disk. Double check for available local data, which prevents the NULL pointer deref. If we are diskless, turn the resume-io in this situation into the first stage of a "force down", by bumping the "effective" data gen id, which will prevent later attach or connect to the former data set without first being demoted (deconfigured). Signed-off-by:
-
Philipp Reisner authored
The intention is to reduce CPU utilization. Recent measurements unveiled that the current performance bottleneck is CPU utilization on the receiving node. The asender thread became CPU limited. One of the main points is to eliminate the idr_for_each_entry() loop from the sending acks code path. One exception in that is sending back ping_acks. These stay in the ack-receiver thread. Otherwise the logic becomes too complicated for no added value. Signed-off-by:
-
Philipp Reisner authored
This prepares the next patch where the sending on the meta (or control) socket is moved to a dedicated workqueue. Signed-off-by:
-
Lars Ellenberg authored
A D_FAILED disk transitions as quickly as possible to D_DISKLESS. But in the "unresponsive local disk" case, there remains a time window where a administrative detach command could find the disk already failed, but some internal meta data IO against the unresponsive local disk still pending. In that case, drbd_md_get_buffer() will return NULL. Don't unconditionally call drbd_md_put_buffer(), or it will cause refcount imbalance, and prevent any further re-attach on this volume (until it is deleted and re-created). Signed-off-by:
-
Lars Ellenberg authored
The recent (not yet released) backport of the extended state broadcasts to support the "events2" subcommand of drbdsetup had some glitches. remember_old_state() would first count all connections with a net_conf != NULL, then allocate a suitable array, then populate that array with all connections found to have net_conf != NULL. This races with the state change to C_STANDALONE, and the NULL assignment there. remember_new_state() then iterates over said connection array, assuming that it would be fully populated. But rcu_lock() just makes sure the thing some pointer points to, if any, won't go away. It does not make the pointer itself immutable. In fact there is no need to "filter" connections based on whether or not they have a currently valid configuration. Just record them always, if they don't have a config, that's fine, there will be no change then. Signed-off-by:
-
Lars Ellenberg authored
Don't blame the peer for being unresponsive, if we did not even ask the question yet. Signed-off-by:
-
Lars Ellenberg authored
The only way to make DRBD intentionally call panic is to set a disk timeout, have that trigger, "abort" some request and complete to upper layers, then have the backend IO subsystem later complete these requests successfully regardless. As the attached IO pages have been recycled for other purposes meanwhile, this will cause unexpected random memory changes. To prevent corruption, we rather panic in that case. Make it obvious from stack traces that this was the case by introducing drbd_panic_after_delayed_completion_of_aborted_request(). Signed-off-by:
-
Lars Ellenberg authored
Even though we really want to get the state information about our bad disk to the peer as soon as possible, it is useful to first call the local-io-error handler. People may chose to hard-reset the box from there. If that looks and behaves exactly like a "regular node crash", without bumping the data generation UUIDs on the peer in between, it makes it easier to deal with. If you intend to return from the local-io-error handler, then better return as quickly as possible to avoid triggering other timeouts. Signed-off-by:
-
Lars Ellenberg authored
If for some reason the primary lost its disk *and* the replication link before it is able to communicate the disk loss, probably blocked IO, then later is able to re-establish the connection, the peer needs to bump its UUIDs just like it does when peer only loses the disk and is able to communicate this in time. Otherwise, a later re-attach of the disk on the primary may start a resync in the "wrong" direction. Signed-off-by:
-
Lars Ellenberg authored
When detaching, we make sure no application IO is in-flight by internally suspending IO, then trigger the state change, wait for the result, and finally internally resume IO again. Once we triggered the stat change to "Failed", we expect it to change from Failed to Diskless. (To avoid races, we actually wait for it to leave "Failed"). On an unresponsive local IO backend, this may not happen, ever. Don't have a "hung" detach block IO "forever", but resume IO before waiting for the state change to Diskless. We may well be able to continue IO to and from a healthy peer. Signed-off-by:
-
Lars Ellenberg authored
Signed-off-by:
-
Lars Ellenberg authored
(You should not use disk-timeout anyways, see the man page for why...) We add incoming requests to the tail of some ring list. On local completion, requests are removed from that list. The timer looks only at the head of that ring list, so is supposed to only see the oldest request. All protected by a spinlock. The request object is created with timestamps zeroed out. The timestamp was only filled in just before the actual submit. But to actually submit the request, we need to give up the spinlock. If you are unlucky, there is no older still pending request, the timer looks at a new request with timestamp still zero (before it even was submitted), and 0 + timeout is most likely older than "now". Better assign the timestamp right when we put the request object on said ring list. Signed-off-by:
-
Philipp Reisner authored
GFP_NOWAIT has a value of 0. I.e. functionality not changed. Signed-off-by:
-
Markus Elfring authored
The lc_destroy() function tests whether its argument is NULL and then returns immediately. Thus the test around the call is not needed. This issue was detected by using the Coccinelle software. Signed-off-by:
Markus Elfring <elfring@users.sourceforge.net> Signed-off-by:
Roland Kammerer <roland.kammerer@linbit.com> Signed-off-by:
-
Andreas Gruenbacher authored
The status command originates the drbd9 code base. While for now we keep the status information in /proc/drbd available, this commit allows the user base to gracefully migrate their monitoring infrastructure to the new status reporting interface. In drbd9 no status information is exposed through /proc/drbd. Signed-off-by:
-
Andreas Gruenbacher authored
The events2 command originates from drbd-9 development. It features more information but requires a incompatible change in output format. Therefore the previous events command continues to exist, the new improved events2 command becomes available now. This prepares the user-base for a later switch to the complete drbd9 code base. Signed-off-by:
-
