PD 3.0 spec defines a new mechanism for power role swap called
Fast role swap. This change enables TCPM to support FRS when
acting as sink.

Once the explicit contract is negotiated, sink port is
expected to query the source port for sink caps to
determine whether the source is FRS capable.
Bits 23 & 24 of fixed pdo of the sink caps from the source, when
set, indicates the current needed by the source when fast role
swap is in progress(Implicit contract phasae). 0 indicates that
the source does not support Fast Role Swap.

Upon receiving the FRS signal from the source,
TCPC(TCPM_FRS_EVENT) informs TCPM to start the Fast role swap sequence.

1. TCPM sends FRS PD message: FR_SWAP_SEND
2. If response is not received within the expiry of
   SenderResponseTimer, Error recovery is triggered.:
   FR_SWAP_SEND_TIMEOUT
3. Upon receipt of the accept message, TCPM waits for
   PSSourceOffTimer for PS_READY message from the partner:
   FR_SWAP_SNK_SRC_NEW_SINK_READY.

TCPC is expected to autonomously turn on vbus once the FRS
signal is received and vbus voltage falls below vsafe5v within
tSrcFrSwap. This is different from traditional power role swap
where the vbus sourcing is turned on by TCPM.

4. By this time, TCPC most likely would have started to
   source vbus, TCPM waits for tSrcFrSwap to see  if the
   lower level TCPC driver signals TCPM_SOURCING_VBUS event:
   FR_SWAP_SNK_SRC_SOURCE_VBUS_APPLIED.
5. When TCPC signals sourcing vbus, TCPM sends PS_READY msg and
   changes the CC pin from Rd to Rp. This is the end of fast
   role swap sequence and TCPM initiates the sequnce to negotiate
   explicit contract by transitioning into SRC_STARTUP after
   SwapSrcStart.

The code is written based on the sequence described in "Figure 8-107:
Dual-role Port in Sink to Source Fast Role Swap State Diagram" of
USB Power Delivery Specification Revision 3.0, Version 1.2.
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20201008061556.1402293-7-badhri@google.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Chip level TCPC driver for Maxim's TCPCI implementation.
This TCPC implementation does not support the following
commands: COMMAND.SinkVbus, COMMAND.SourceVbusDefaultVoltage,
COMMAND.SourceVbusHighVoltage. Instead the sinking and sourcing
from vbus is supported by writes to custom registers.
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20201008061556.1402293-5-badhri@google.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

set_vbus callback allows TCPC which are TCPCI based, however,
does not support turning on sink and source mode through
Command.SinkVbus and Command.SourceVbusDefaultVoltage.
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20201008061556.1402293-3-badhri@google.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Allow chip level drivers to retrieve reference to tcpm_port.
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20201008061556.1402293-2-badhri@google.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

kcov testing uncovered call to usb_hcd_giveback_urb() without disabling
interrupts.

Link: https://lore.kernel.org/linux-usb/CAAeHK+wb4k-LGTjK9F5YbJNviF_+yU+wE_=Vpo9Rn7KFN8vG6Q@mail.gmail.com/

usb_hcd_giveback_urb() is called from vhci's urb_enqueue, when it
determines it doesn't need to xmit the urb and can give it back.
This path runs in task context.

Disable irqs around usb_hcd_giveback_urb() call.
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/20201006223914.39257-1-skhan@linuxfoundation.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The ES58X devices has a CDC ACM interface (used for debug
purpose). During probing, the device is thus recognized as USB Modem
(CDC ACM), preventing the etas-es58x module to load:
  usbcore: registered new interface driver etas_es58x
  usb 1-1.1: new full-speed USB device number 14 using xhci_hcd
  usb 1-1.1: New USB device found, idVendor=108c, idProduct=0159, bcdDevice= 1.00
  usb 1-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
  usb 1-1.1: Product: ES581.4
  usb 1-1.1: Manufacturer: ETAS GmbH
  usb 1-1.1: SerialNumber: 2204355
  cdc_acm 1-1.1:1.0: No union descriptor, testing for castrated device
  cdc_acm 1-1.1:1.0: ttyACM0: USB ACM device

Thus, these have been added to the ignore list in
drivers/usb/class/cdc-acm.c

N.B. Future firmware release of the ES58X will remove the CDC-ACM
interface.

`lsusb -v` of the three devices variant (ES581.4, ES582.1 and
ES584.1):

  Bus 001 Device 011: ID 108c:0159 Robert Bosch GmbH ES581.4
  Device Descriptor:
    bLength                18
    bDescriptorType         1
    bcdUSB               1.10
    bDeviceClass            2 Communications
    bDeviceSubClass         0
    bDeviceProtocol         0
    bMaxPacketSize0        64
    idVendor           0x108c Robert Bosch GmbH
    idProduct          0x0159
    bcdDevice            1.00
    iManufacturer           1 ETAS GmbH
    iProduct                2 ES581.4
    iSerial                 3 2204355
    bNumConfigurations      1
    Configuration Descriptor:
      bLength                 9
      bDescriptorType         2
      wTotalLength       0x0035
      bNumInterfaces          1
      bConfigurationValue     1
      iConfiguration          5 Bus Powered Configuration
      bmAttributes         0x80
        (Bus Powered)
      MaxPower              100mA
      Interface Descriptor:
        bLength                 9
        bDescriptorType         4
        bInterfaceNumber        0
        bAlternateSetting       0
        bNumEndpoints           3
        bInterfaceClass         2 Communications
        bInterfaceSubClass      2 Abstract (modem)
        bInterfaceProtocol      0
        iInterface              4 ACM Control Interface
        CDC Header:
          bcdCDC               1.10
        CDC Call Management:
          bmCapabilities       0x01
            call management
          bDataInterface          0
        CDC ACM:
          bmCapabilities       0x06
            sends break
            line coding and serial state
        Endpoint Descriptor:
          bLength                 7
          bDescriptorType         5
          bEndpointAddress     0x81  EP 1 IN
          bmAttributes            3
            Transfer Type            Interrupt
            Synch Type               None
            Usage Type               Data
          wMaxPacketSize     0x0010  1x 16 bytes
          bInterval              10
        Endpoint Descriptor:
          bLength                 7
          bDescriptorType         5
          bEndpointAddress     0x82  EP 2 IN
          bmAttributes            2
            Transfer Type            Bulk
            Synch Type               None
            Usage Type               Data
          wMaxPacketSize     0x0040  1x 64 bytes
          bInterval               0
        Endpoint Descriptor:
          bLength                 7
          bDescriptorType         5
          bEndpointAddress     0x03  EP 3 OUT
          bmAttributes            2
            Transfer Type            Bulk
            Synch Type               None
            Usage Type               Data
          wMaxPacketSize     0x0040  1x 64 bytes
          bInterval               0
  Device Status:     0x0000
    (Bus Powered)

  Bus 001 Device 012: ID 108c:0168 Robert Bosch GmbH ES582
  Device Descriptor:
    bLength                18
    bDescriptorType         1
    bcdUSB               2.00
    bDeviceClass            2 Communications
    bDeviceSubClass         0
    bDeviceProtocol         0
    bMaxPacketSize0        64
    idVendor           0x108c Robert Bosch GmbH
    idProduct          0x0168
    bcdDevice            1.00
    iManufacturer           1 ETAS GmbH
    iProduct                2 ES582
    iSerial                 3 0108933
    bNumConfigurations      1
    Configuration Descriptor:
      bLength                 9
      bDescriptorType         2
      wTotalLength       0x0043
      bNumInterfaces          2
      bConfigurationValue     1
      iConfiguration          0
      bmAttributes         0x80
        (Bus Powered)
      MaxPower              500mA
      Interface Descriptor:
        bLength                 9
        bDescriptorType         4
        bInterfaceNumber        0
        bAlternateSetting       0
        bNumEndpoints           1
        bInterfaceClass         2 Communications
        bInterfaceSubClass      2 Abstract (modem)
        bInterfaceProtocol      1 AT-commands (v.25ter)
        iInterface              0
        CDC Header:
          bcdCDC               1.10
        CDC ACM:
          bmCapabilities       0x02
            line coding and serial state
        CDC Union:
          bMasterInterface        0
          bSlaveInterface         1
        CDC Call Management:
          bmCapabilities       0x03
            call management
            use DataInterface
          bDataInterface          1
        Endpoint Descriptor:
          bLength                 7
          bDescriptorType         5
          bEndpointAddress     0x83  EP 3 IN
          bmAttributes            3
            Transfer Type            Interrupt
            Synch Type               None
            Usage Type               Data
          wMaxPacketSize     0x0040  1x 64 bytes
          bInterval              16
      Interface Descriptor:
        bLength                 9
        bDescriptorType         4
        bInterfaceNumber        1
        bAlternateSetting       0
        bNumEndpoints           2
        bInterfaceClass        10 CDC Data
        bInterfaceSubClass      0
        bInterfaceProtocol      0
        iInterface              0
        Endpoint Descriptor:
          bLength                 7
          bDescriptorType         5
          bEndpointAddress     0x81  EP 1 IN
          bmAttributes            2
            Transfer Type            Bulk
            Synch Type               None
            Usage Type               Data
          wMaxPacketSize     0x0200  1x 512 bytes
          bInterval               0
        Endpoint Descriptor:
          bLength                 7
          bDescriptorType         5
          bEndpointAddress     0x02  EP 2 OUT
          bmAttributes            2
            Transfer Type            Bulk
            Synch Type               None
            Usage Type               Data
          wMaxPacketSize     0x0200  1x 512 bytes
          bInterval               0
  Device Qualifier (for other device speed):
    bLength                10
    bDescriptorType         6
    bcdUSB               2.00
    bDeviceClass            2 Communications
    bDeviceSubClass         0
    bDeviceProtocol         0
    bMaxPacketSize0        64
    bNumConfigurations      1
  Device Status:     0x0000
    (Bus Powered)

  Bus 001 Device 013: ID 108c:0169 Robert Bosch GmbH ES584.1
  Device Descriptor:
    bLength                18
    bDescriptorType         1
    bcdUSB               2.00
    bDeviceClass            2 Communications
    bDeviceSubClass         0
    bDeviceProtocol         0
    bMaxPacketSize0        64
    idVendor           0x108c Robert Bosch GmbH
    idProduct          0x0169
    bcdDevice            1.00
    iManufacturer           1 ETAS GmbH
    iProduct                2 ES584.1
    iSerial                 3 0100320
    bNumConfigurations      1
    Configuration Descriptor:
      bLength                 9
      bDescriptorType         2
      wTotalLength       0x0043
      bNumInterfaces          2
      bConfigurationValue     1
      iConfiguration          0
      bmAttributes         0x80
        (Bus Powered)
      MaxPower              500mA
      Interface Descriptor:
        bLength                 9
        bDescriptorType         4
        bInterfaceNumber        0
        bAlternateSetting       0
        bNumEndpoints           1
        bInterfaceClass         2 Communications
        bInterfaceSubClass      2 Abstract (modem)
        bInterfaceProtocol      1 AT-commands (v.25ter)
        iInterface              0
        CDC Header:
          bcdCDC               1.10
        CDC ACM:
          bmCapabilities       0x02
            line coding and serial state
        CDC Union:
          bMasterInterface        0
          bSlaveInterface         1
        CDC Call Management:
          bmCapabilities       0x03
            call management
            use DataInterface
          bDataInterface          1
        Endpoint Descriptor:
          bLength                 7
          bDescriptorType         5
          bEndpointAddress     0x83  EP 3 IN
          bmAttributes            3
            Transfer Type            Interrupt
            Synch Type               None
            Usage Type               Data
          wMaxPacketSize     0x0040  1x 64 bytes
          bInterval              16
      Interface Descriptor:
        bLength                 9
        bDescriptorType         4
        bInterfaceNumber        1
        bAlternateSetting       0
        bNumEndpoints           2
        bInterfaceClass        10 CDC Data
        bInterfaceSubClass      0
        bInterfaceProtocol      0
        iInterface              0
        Endpoint Descriptor:
          bLength                 7
          bDescriptorType         5
          bEndpointAddress     0x81  EP 1 IN
          bmAttributes            2
            Transfer Type            Bulk
            Synch Type               None
            Usage Type               Data
          wMaxPacketSize     0x0200  1x 512 bytes
          bInterval               0
        Endpoint Descriptor:
          bLength                 7
          bDescriptorType         5
          bEndpointAddress     0x02  EP 2 OUT
          bmAttributes            2
            Transfer Type            Bulk
            Synch Type               None
            Usage Type               Data
          wMaxPacketSize     0x0200  1x 512 bytes
          bInterval               0
  Device Qualifier (for other device speed):
    bLength                10
    bDescriptorType         6
    bcdUSB               2.00
    bDeviceClass            2 Communications
    bDeviceSubClass         0
    bDeviceProtocol         0
    bMaxPacketSize0        64
    bNumConfigurations      1
  Device Status:     0x0000
    (Bus Powered)
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201002154219.4887-8-mailhol.vincent@wanadoo.frSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

We need the USB fixes in here as well for testing.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull kvm fixes from Paolo Bonzini:
 "Two bugfixes"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: VMX: update PFEC_MASK/PFEC_MATCH together with PF intercept
  KVM: arm64: Restore missing ISB on nVHE __tlb_switch_to_guest

Pull xen fix from Juergen Gross:
 "Fix a regression introduced in 5.9-rc3 which caused a system running
  as fully virtualized guest under Xen to crash when using legacy
  devices like a floppy"

* tag 'for-linus-5.9b-rc8-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  xen/events: don't use chip_data for legacy IRQs

Pull USB/PHY fixes from Greg KH:
 "Here are some small USB and PHY driver fixes for 5.9-rc8

  The PHY driver fix resolves an issue found by Dan Carpenter for a
  memory leak.

  The USB fixes fall into two groups:

   - usb gadget fix from Bryan that is a fix for a previous security fix
     that showed up in in-the-wild testing

   - usb core driver matching bugfixes. This fixes a bug that has
     plagued the both the usbip driver and syzbot testing tools this -rc
     release cycle. All is now working properly so usbip connections
     will work, and syzbot can get back to fuzzing USB drivers properly.

  All have been in linux-next for a while with no reported issues"

* tag 'usb-5.9-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  usbcore/driver: Accommodate usbip
  usbcore/driver: Fix incorrect downcast
  usbcore/driver: Fix specific driver selection
  Revert "usbip: Implement a match function to fix usbip"
  USB: gadget: f_ncm: Fix NDP16 datagram validation
  phy: ti: am654: Fix a leak in serdes_am654_probe()

Pull i2c fixes from Wolfram Sang:
 "Some more driver fixes for i2c"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: npcm7xx: Clear LAST bit after a failed transaction.
  i2c: cpm: Fix i2c_ram structure
  i2c: i801: Exclude device from suspend direct complete optimization

Pull input fixes from Dmitry Torokhov:
 "A couple more driver quirks, now enabling newer trackpoints from
  Synaptics for real"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: i8042 - add nopnp quirk for Acer Aspire 5 A515
  Input: trackpoint - enable Synaptics trackpoints

One of the entries has three fields "mistake||correction||correction"
rather than the expected two fields "mistake||correction".  Fix it.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Link: https://lkml.kernel.org/r/20200930234359.255295-1-ebiggers@kernel.orgSigned-off-by: Linus Torvalds <torvalds@linux-foundation.org>

memalloc_nocma_{save/restore} APIs can be used to skip page allocation
on CMA area, but, there is a missing case and the page on CMA area could
be allocated even if APIs are used.  This patch handles this case to fix
the potential issue.

For now, these APIs are used to prevent long-term pinning on the CMA
page.  When the long-term pinning is requested on the CMA page, it is
migrated to the non-CMA page before pinning.  This non-CMA page is
allocated by using memalloc_nocma_{save/restore} APIs.  If APIs doesn't
work as intended, the CMA page is allocated and it is pinned for a long
time.  This long-term pin for the CMA page causes cma_alloc() failure
and it could result in wrong behaviour on the device driver who uses the
cma_alloc().

Missing case is an allocation from the pcplist.  MIGRATE_MOVABLE pcplist
could have the pages on CMA area so we need to skip it if ALLOC_CMA
isn't specified.

Fixes: 8510e69c (mm/page_alloc: fix memalloc_nocma_{save/restore} APIs)
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: "Aneesh Kumar K . V" <aneesh.kumar@linux.ibm.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Link: https://lkml.kernel.org/r/1601429472-12599-1-git-send-email-iamjoonsoo.kim@lge.comSigned-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The routine that applies debug flags to the kmem_cache slabs
inadvertantly prevents non-debug flags from being applied to those
same objects.  That is, if slub_debug=<flag>,<slab> is specified,
non-debugged slabs will end up having flags of zero, and the slabs
may be unusable.

Fix this by including the input flags for non-matching slabs with the
contents of slub_debug, so that the caches are created as expected
alongside any debugging options that may be requested.  With this, we
can remove the check for a NULL slub_debug_string, since it's covered
by the loop itself.

Fixes: e17f1dfb ("mm, slub: extend slub_debug syntax for multiple blocks")
Signed-off-by: Eric Farman <farman@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Kees Cook <keescook@chromium.org>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Link: https://lkml.kernel.org/r/20200930161931.28575-1-farman@linux.ibm.comSigned-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Felipe writes:

USB: changes for v5.10 merge window

Most of changes are on dwc3 (38.8%) with cdns3 falling close
behind (24.1%).

The biggest changes here are a series of non-critical fixes to corner
cases on dwc3, produced by Thinh N, and a series of major improvements
to cdns3 produced by Peter C.

We also have the traditional set of new device support (Intel Keem
Bay, Hikey 970) on dwc3. A series of sparse/coccinelle and checkpatch
fixes on dwc3 by yours truly and a set of minor changes all over the
stack.

* tag 'usb-for-v5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb: (117 commits)
  usb: dwc2: Fix INTR OUT transfers in DDMA mode.
  usb: dwc2: don't use ID/Vbus detection if usb-role-switch on STM32MP15 SoCs
  usb: dwc2: override PHY input signals with usb role switch support
  dt-bindings: usb: dwc2: add optional usb-role-switch property
  usb: dwc3: of-simple: Add compatible string for Intel Keem Bay platform
  dt-bindings: usb: Add Intel Keem Bay USB controller bindings
  usb: dwc3: gadget: Support up to max stream id
  usb: dwc3: gadget: Return early if no TRB update
  usb: dwc3: gadget: Keep TRBs in request order
  usb: dwc3: gadget: Revise setting IOC when no TRB left
  usb: dwc3: gadget: Look ahead when setting IOC
  usb: dwc3: gadget: Allow restarting a transfer
  usb: bdc: remove duplicated error message
  usb: dwc3: Stop active transfers before halting the controller
  usb: cdns3: gadget: enlarge the TRB ring length
  usb: cdns3: gadget: sg_support is only for DEV_VER_V2 or above
  usb: cdns3: gadget: need to handle sg case for workaround 2 case
  usb: cdns3: gadget: handle sg list use case at completion correctly
  usb: cdns3: gadget: add CHAIN and ISP bit for sg list use case
  usb: cdns3: gadget: improve the dump TRB operation at cdns3_ep_run_transfer
  ...

Merge tag 'kvmarm-fixes-5.9-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into kvm-master

KVM/arm64 fixes for 5.9, take #3

- Fix synchronization of VTTBR update on TLB invalidation for nVHE systems

The PFEC_MASK and PFEC_MATCH fields in the VMCS reverse the meaning of
the #PF intercept bit in the exception bitmap when they do not match.
This means that, if PFEC_MASK and/or PFEC_MATCH are set, the
hypervisor can get a vmexit for #PF exceptions even when the
corresponding bit is clear in the exception bitmap.

This is unexpected and is promptly detected by a WARN_ON_ONCE.
To fix it, reset PFEC_MASK and PFEC_MATCH when the #PF intercept
is disabled (as is common with enable_ept && !allow_smaller_maxphyaddr).
Reported-by: Qian Cai <cai@redhat.com&gt;>
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Tested-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

Pull pin control fixes from Linus Walleij:
 "Some pin control fixes here. All of them are driver fixes, the Intel
  Cherryview being the most interesting one.

   - Fix a mux problem for I2C in the MVEBU driver.

   - Fix a really hairy inversion problem in the Intel Cherryview
     driver.

   - Fix the register for the sdc2_clk in the Qualcomm SM8250 driver.

   - Check the virtual GPIO boot failur in the Mediatek driver"

* tag 'pinctrl-v5.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
  pinctrl: mediatek: check mtk_is_virt_gpio input parameter
  pinctrl: qcom: sm8250: correct sdc2_clk
  pinctrl: cherryview: Preserve CHV_PADCTRL1_INVRXTX_TXDATA flag on GPIOs
  pinctrl: mvebu: Fix i2c sda definition for 98DX3236

Pull PCI fixes from Bjorn Helgaas:

 - Fix rockchip regression in rockchip_pcie_valid_device() (Lorenzo
   Pieralisi)

 - Add Pali Rohár as aardvark PCI maintainer (Pali Rohár)

* tag 'pci-v5.9-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  MAINTAINERS: Add Pali Rohár as aardvark PCI maintainer
  PCI: rockchip: Fix bus checks in rockchip_pcie_valid_device()

Pull SCSI fixes from James Bottomley:
 "Two patches in driver frameworks. The iscsi one corrects a bug induced
  by a BPF change to network locking and the other is a regression we
  introduced"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: iscsi: iscsi_tcp: Avoid holding spinlock while calling getpeername()
  scsi: target: Fix lun lookup for TARGET_SCF_LOOKUP_LUN_FROM_TAG case

Pull io_uring fixes from Jens Axboe:

 - fix for async buffered reads if read-ahead is fully disabled (Hao)

 - double poll match fix

 - ->show_fdinfo() potential ABBA deadlock complaint fix

* tag 'io_uring-5.9-2020-10-02' of git://git.kernel.dk/linux-block:
  io_uring: fix async buffered reads when readahead is disabled
  io_uring: fix potential ABBA deadlock in ->show_fdinfo()
  io_uring: always delete double poll wait entry on match

Pull block fix from Jens Axboe:
 "Single fix for a ->commit_rqs failure case"

* tag 'block-5.9-2020-10-02' of git://git.kernel.dk/linux-block:
  blk-mq: call commit_rqs while list empty but error happen

Pull epoll fixes from Al Viro:
 "Several race fixes in epoll"

* 'work.epoll' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  ep_create_wakeup_source(): dentry name can change under you...
  epoll: EPOLL_CTL_ADD: close the race in decision to take fast path
  epoll: replace ->visited/visited_list with generation count
  epoll: do not insert into poll queues until all sanity checks are done

Pull RISC-V fixes from Palmer Dabbelt:
 "Two fixes for this week:

   - The addition of a symbol export for clint_time_val, which has been
     inlined into some timex functions and can be used by drivers.

   - A fix to avoid calling get_cycles() before the timers have been
     probed.

  These both only effect !MMU systems"

* tag 'riscv-for-linus-5.9-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
  RISC-V: Check clint_time_val before use
  clocksource: clint: Export clint_time_val for modules

Pull btrfs fixes from David Sterba:
 "Two more fixes.

  One is for a lockdep warning/lockup (also caught by syzbot), that one
  has been seen in practice. Regarding the other syzbot reports
  mentioned last time, they don't seem to be urgent and reliably
  reproducible so they'll be fixed later.

  The second fix is for a potential corruption when device replace
  finishes and the in-memory state of trim is not copied to the new
  device"

* tag 'for-5.9-rc7-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
  btrfs: fix filesystem corruption after a device replace
  btrfs: move btrfs_rm_dev_replace_free_srcdev outside of all locks
  btrfs: move btrfs_scratch_superblocks into btrfs_dev_replace_finishing

Pull power management fixes from Rafael Wysocki:
 "These fix one more issue related to the recent RCU-lockdep changes, a
  typo in documentation and add a missing return statement to
  intel_pstate.

  Specifics:

   - Fix up RCU usage for cpuidle on the ARM imx6q platform (Ulf
     Hansson)

   - Fix typo in the PM documentation (Yoann Congal)

   - Add return statement that is missing after recent changes in the
     intel_pstate driver (Zhang Rui)"

* tag 'pm-5.9-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ARM: imx6q: Fixup RCU usage for cpuidle
  Documentation: PM: Fix a reStructuredText syntax error
  cpufreq: intel_pstate: Fix missing return statement

Pull IIO fixes from Greg KH:
 "Here are two small IIO driver fixes for 5.9-rc8 that resolve some
  reported issues:

   - driver name fixed in one driver

   - device name typo fixed

  Both have been in linux-next for a while with no reported problems"

* tag 'staging-5.9-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  iio: adc: qcom-spmi-adc5: fix driver name
  iio: adc: ad7124: Fix typo in device name

Pull GPIO fixes from Linus Walleij:
 "Some late GPIO fixes for the v5.9 series:

   - Fix compiler warnings on the OMAP when PM is disabled

   - Clear the interrupt when setting edge sensitivity on the Spreadtrum
     driver.

   - Fix up spurious interrupts on the TC35894.

   - Support threaded interrupts on the Siox controller.

   - Fix resource leaks on the mockup driver.

   - Fix line event handling in syscall compatible mode for the
     character device.

   - Fix an unitialized variable in the PCA953A driver.

   - Fix access to all GPIO IRQs on the Aspeed AST2600.

   - Fix line direction on the AMD FCH driver.

   - Use the bitmap API instead of compiler intrinsics for bit
     manipulation in the PCA953x driver"

* tag 'gpio-v5.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
  gpio: pca953x: Correctly initialize registers 6 and 7 for PCA957x
  gpio: pca953x: Use bitmap API over implicit GCC extension
  gpio: amd-fch: correct logic of GPIO_LINE_DIRECTION
  gpio: aspeed: fix ast2600 bank properties
  gpio/aspeed-sgpio: don't enable all interrupts by default
  gpio/aspeed-sgpio: enable access to all 80 input & output sgpios
  gpio: pca953x: Fix uninitialized pending variable
  gpiolib: Fix line event handling in syscall compatible mode
  gpio: mockup: fix resource leak in error path
  gpio: siox: explicitly support only threaded irqs
  gpio: tc35894: fix up tc35894 interrupt configuration
  gpio: sprd: Clear interrupt when setting the type as edge
  gpio: omap: Fix warnings if PM is disabled

Pull MMC fixes from Ulf Hansson:

 - Fix deadlock when removing MEMSTICK host

 - Workaround broken CMDQ on Intel GLK based IRBIS models

* tag 'mmc-v5.9-rc4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
  mmc: sdhci: Workaround broken command queuing on Intel GLK based IRBIS models
  memstick: Skip allocating card when removing host

Commit f227e3ec ("random32: update the net random state on interrupt
and activity") broke compilation and was temporarily fixed by Linus in
83bdc727 ("random32: remove net_rand_state from the latent entropy
gcc plugin") by entirely moving net_rand_state out of the things handled
by the latent_entropy GCC plugin.

From what I understand when reading the plugin code, using the
__latent_entropy attribute on a declaration was the wrong part and
simply keeping the __latent_entropy attribute on the variable definition
was the correct fix.

Fixes: 83bdc727 ("random32: remove net_rand_state from the latent entropy gcc plugin")
Acked-by: Willy Tarreau <w@1wt.eu>
Cc: Emese Revfy <re.emese@gmail.com>
Signed-off-by: Thibaut Sautereau <thibaut.sautereau@ssi.gouv.fr>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* pm-cpufreq:
  cpufreq: intel_pstate: Fix missing return statement

Since commit ea426c2a ("mm: memcg: prepare for byte-sized vmstat
items") the write side of slab counters accepts a value in bytes and
converts it to pages.  It happens in __mod_node_page_state().

However a non-SMP version of __mod_node_page_state() doesn't perform
this conversion.  It leads to incorrect (unrealistically high) slab
counters values.  Fix this by adding a similar conversion to the non-SMP
version of __mod_node_page_state().
Signed-off-by: Roman Gushchin <guro@fb.com>
Reported-and-tested-by: Bastian Bittorf <bb@npl.de>
Fixes: ea426c2a ("mm: memcg: prepare for byte-sized vmstat items")
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The latest reference to usbfs_conn_disc_event() removed in
commit fb28d58b ("USB: remove CONFIG_USB_DEVICEFS")
in 2012 and now a user poll() waits infinitely for content changes.
Signed-off-by: Sergey Korolev <s.korolev@ndmsystems.com>
Link: https://lore.kernel.org/r/20200809161233.13135-1-s.korolev@ndmsystems.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

STMicroelectronics USB Type-C port controllers use I2C interface to
configure, control and read the operation status of the device. All ST USB
Type-C port controllers are based on the same I2C register map. That's why
this driver can be used with all ST USB Type-C ICs.
Some ST USB Type-C port controllers are Dual Role Port (DRP), only Sink or
Source, some supports USB Power Delivery. This can be configured through
connector device tree bindings.

This driver is a basic Type-C port controller driver, with no power
delivery support. It allows to configure ST USB Type-C port controller.
Interrupt is supported and enables CC connection events, to detect
attach and detach and update Type-C subsystem accordingly as well as usb
role switch.

ST USB Type-C port controller can be supplied in three different ways
depending on the target application:
- through VDD pin only (so VDD is the main supply)
- through VSYS pin only (so VSYS is the main supply)
- through VDD and VSYS pins.
When both VDD and VSYS power supplies are present, the low power supply
VSYS is selected as main supply when VSYS voltage is above 3.1V, else
VDD is selected as main supply.

In case of Source or Dual port type, if VDD supply is present, it has to be
enabled in case of Source power role to provide Vbus. When interrupt
support is available, VDD supply is dynamically managed upon attach/detach
interrupt. When there is no interrupt support, VDD supply is enabled by
default.
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Link: https://lore.kernel.org/r/20200924090049.9041-5-amelie.delaunay@st.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch adds a function that converts power operation mode string into
power operation mode value.

It is useful to configure power operation mode through device tree
property, as power capabilities may be linked to hardware design.
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Link: https://lore.kernel.org/r/20200924090049.9041-3-amelie.delaunay@st.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Some platforms have only super speed data bus connected to this device
and high speed data bus directly connected to the SoC. In such platforms
modelling connector as a child of this device is making it non compliant
with usb connector bindings. By modelling connector node as standalone
device node along with this device and the SoC data bus will make it
compliant with usb connector bindings.
Update the driver to handle this model by using OF graph API to get the
connector fwnode and usb role switch class API to get role switch handle.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200920134905.4370-5-biju.das.jz@bp.renesas.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Document HS and SS data bus for the "usb-role-switch" enabled case.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200920134905.4370-4-biju.das.jz@bp.renesas.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Convert ti,hd3ss3220.txt to YAML. Updated the binding documentation
as graph bindings of this device model Super Speed (SS) data bus to
the Super Speed (SS) capable connector.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20200920134905.4370-3-biju.das.jz@bp.renesas.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>