commit 4f031fa9 upstream.

Commit 7ec7c4a9 (mac80211: port CCMP to
cryptoapi's CCM driver) introduced a regression when decrypting empty
packets (data_len == 0). This will lead to backtraces like:

(scatterwalk_start) from [<c01312f4>] (scatterwalk_map_and_copy+0x2c/0xa8)
(scatterwalk_map_and_copy) from [<c013a5a0>] (crypto_ccm_decrypt+0x7c/0x25c)
(crypto_ccm_decrypt) from [<c032886c>] (ieee80211_aes_ccm_decrypt+0x160/0x170)
(ieee80211_aes_ccm_decrypt) from [<c031c628>] (ieee80211_crypto_ccmp_decrypt+0x1ac/0x238)
(ieee80211_crypto_ccmp_decrypt) from [<c032ef28>] (ieee80211_rx_handlers+0x870/0x1d24)
(ieee80211_rx_handlers) from [<c0330c7c>] (ieee80211_prepare_and_rx_handle+0x8a0/0x91c)
(ieee80211_prepare_and_rx_handle) from [<c0331260>] (ieee80211_rx+0x568/0x730)
(ieee80211_rx) from [<c01d3054>] (__carl9170_rx+0x94c/0xa20)
(__carl9170_rx) from [<c01d3324>] (carl9170_rx_stream+0x1fc/0x320)
(carl9170_rx_stream) from [<c01cbccc>] (carl9170_usb_tasklet+0x80/0xc8)
(carl9170_usb_tasklet) from [<c00199dc>] (tasklet_hi_action+0x88/0xcc)
(tasklet_hi_action) from [<c00193c8>] (__do_softirq+0xcc/0x200)
(__do_softirq) from [<c0019734>] (irq_exit+0x80/0xe0)
(irq_exit) from [<c0009c10>] (handle_IRQ+0x64/0x80)
(handle_IRQ) from [<c000c3a0>] (__irq_svc+0x40/0x4c)
(__irq_svc) from [<c0009d44>] (arch_cpu_idle+0x2c/0x34)

Such packets can appear for example when using the carl9170 wireless driver
because hardware sometimes generates garbage when the internal FIFO overruns.

This patch adds an additional length check.

Fixes: 7ec7c4a9 ("mac80211: port CCMP to cryptoapi's CCM driver")
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Ronald Wahl <ronald.wahl@raritan.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 152d44a8 upstream.

I used some 64 bit instructions when adding the 32 bit getcpu VDSO
function. Fix it.

Fixes: 18ad51dd ("powerpc: Add VDSO version of getcpu")
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit aec653c4 upstream.

Call igb_setup_link() when the PHY is powered up.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Reported-by: Jeff Westfahl <jeff.westfahl@ni.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Vincent Donnefort <vdonnefort@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 338b522c upstream.

With -cpu host, KVM reports LBR and extra_regs support, if the host has
support.

When the guest perf driver tries to access LBR or extra_regs MSR,
it #GPs all MSR accesses,since KVM doesn't handle LBR and extra_regs support.
So check the related MSRs access right once at initialization time to avoid
the error access at runtime.

For reproducing the issue, please build the kernel with CONFIG_KVM_INTEL = y
(for host kernel).
And CONFIG_PARAVIRT = n and CONFIG_KVM_GUEST = n (for guest kernel).
Start the guest with -cpu host.
Run perf record with --branch-any or --branch-filter in guest to trigger LBR
Run perf stat offcore events (E.g. LLC-loads/LLC-load-misses ...) in guest to
trigger offcore_rsp #GP
Signed-off-by: Kan Liang <kan.liang@intel.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Maria Dimakopoulou <maria.n.dimakopoulou@gmail.com>
Cc: Mark Davies <junk@eslaf.co.uk>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Yan, Zheng <zheng.z.yan@intel.com>
Link: http://lkml.kernel.org/r/1405365957-20202-1-git-send-email-kan.liang@intel.comSigned-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Dongsu Park <dongsu.park@profitbricks.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 9772b54c ]

To accomodate for enough headroom for tunnels, use MAX_HEADER instead
of LL_MAX_HEADER. Robert reported that he has hit after roughly 40hrs
of trinity an skb_under_panic() via SCTP output path (see reference).
I couldn't reproduce it from here, but not using MAX_HEADER as elsewhere
in other protocols might be one possible cause for this.

In any case, it looks like accounting on chunks themself seems to look
good as the skb already passed the SCTP output path and did not hit
any skb_over_panic(). Given tunneling was enabled in his .config, the
headroom would have been expanded by MAX_HEADER in this case.
Reported-by: Robert Święcki <robert@swiecki.net>
Reference: https://lkml.org/lkml/2014/12/1/507
Fixes: 594ccc14 ("[SCTP] Replace incorrect use of dev_alloc_skb with alloc_skb in sctp_packet_transmit().")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 5f478b41 ]

mvneta_tx() dereferences skb to get skb->len too late,
as hardware might have completed the transmit and TX completion
could have freed the skb from another cpu.

Fixes: 71f6d1b3 ("net: mvneta: replace Tx timer with a real interrupt")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit aebea2ba ]

The mvneta driver sets the amount of Tx coalesce packets to 16 by
default. Normally that does not cause any trouble since the driver
uses a much larger Tx ring size (532 packets). But some sockets
might run with very small buffers, much smaller than the equivalent
of 16 packets. This is what ping is doing for example, by setting
SNDBUF to 324 bytes rounded up to 2kB by the kernel.

The problem is that there is no documented method to force a specific
packet to emit an interrupt (eg: the last of the ring) nor is it
possible to make the NIC emit an interrupt after a given delay.

In this case, it causes trouble, because when ping sends packets over
its raw socket, the few first packets leave the system, and the first
15 packets will be emitted without an IRQ being generated, so without
the skbs being freed. And since the socket's buffer is small, there's
no way to reach that amount of packets, and the ping ends up with
"send: no buffer available" after sending 6 packets. Running with 3
instances of ping in parallel is enough to hide the problem, because
with 6 packets per instance, that's 18 packets total, which is enough
to grant a Tx interrupt before all are sent.

The original driver in the LSP kernel worked around this design flaw
by using a software timer to clean up the Tx descriptors. This timer
was slow and caused terrible network performance on some Tx-bound
workloads (such as routing) but was enough to make tools like ping
work correctly.

Instead here, we simply set the packet counts before interrupt to 1.
This ensures that each packet sent will produce an interrupt. NAPI
takes care of coalescing interrupts since the interrupt is disabled
once generated.

No measurable performance impact nor CPU usage were observed on small
nor large packets, including when saturating the link on Tx, and this
fixes tools like ping which rely on too small a send buffer. If one
wants to increase this value for certain workloads where it is safe
to do so, "ethtool -C $dev tx-frames" will override this default
setting.

This fix needs to be applied to stable kernels starting with 3.10.
Tested-By: Maggie Mae Roxas <maggie.mae.roxas@gmail.com>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 6fb2a756 ]

Set the inner mac header to point to the GRE payload when
doing GRO. This is needed if we proceed to send the packet
through GRE GSO which now uses the inner mac header instead
of inner network header to determine the length of encapsulation
headers.

Fixes: 14051f04 ("gre: Use inner mac length when computing tunnel length")
Reported-by: Wolfgang Walter <linux@stwm.de>
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit e0ebde0e ]

rtnl_link_get_net() holds a reference on the 'struct net', we need to release
it in case of error.

CC: Eric W. Biederman <ebiederm@xmission.com>
Fixes: b51642f6 ("net: Enable a userns root rtnl calls that are safe for unprivilged users")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reviewed-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 2d5c57d7 ]

Some VF drivers use the upper byte of "param1" (the qp count field)
in mlx4_qp_reserve_range() to pass flags which are used to optimize
the range allocation.

Under the current code, if any of these flags are set, the 32-bit
count field yields a count greater than 2^24, which is out of range,
and this VF fails.

As these flags represent a "best-effort" allocation hint anyway, they may
safely be ignored. Therefore, the PF driver may simply mask out the bits.

Fixes: c82e9aa0 "mlx4_core: resource tracking for HCA resources used by guests"
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit a620a6bc ]

If TX channels are set to 4 and RX channels are set to less than 4,
using ethtool -L, the driver will try to initialize more RX channels
than it has allocated, causing an oops.

This fix only initializes the RX ring if it has been allocated.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 00c83b01 ]

Currently, when trying to reuse a socket, vxlan_sock_add will grab
vn->sock_lock, locate a reusable socket, inc refcount and release
vn->sock_lock.

But vxlan_sock_release() will first decrement refcount, and then grab
that lock. refcnt operations are atomic but as currently we have
deferred works which hold vs->refcnt each, this might happen, leading to
a use after free (specially after vxlan_igmp_leave):

  CPU 1                            CPU 2

deferred work                    vxlan_sock_add
  ...                              ...
                                   spin_lock(&vn->sock_lock)
                                   vs = vxlan_find_sock();
  vxlan_sock_release
    dec vs->refcnt, reaches 0
    spin_lock(&vn->sock_lock)
                                   vxlan_sock_hold(vs), refcnt=1
                                   spin_unlock(&vn->sock_lock)
    hlist_del_rcu(&vs->hlist);
    vxlan_notify_del_rx_port(vs)
    spin_unlock(&vn->sock_lock)

So when we look for a reusable socket, we check if it wasn't freed
already before reusing it.
Signed-off-by: Marcelo Ricardo Leitner <mleitner@redhat.com>
Fixes: 7c47cedf ("vxlan: move IGMP join/leave to work queue")
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit be6572fd ]

When using GRE redirection in WCCP, it sets the wrong skb->protocol,
that is, ETH_P_IP instead of ETH_P_IPV6 for the encapuslated traffic.

Fixes: c12b395a ("gre: Support GRE over IPv6")
Cc: Dmitry Kozlov <xeb@mail.ru>
Signed-off-by: Yuri Chislov <yuri.chislov@gmail.com>
Tested-by: Yuri Chislov <yuri.chislov@gmail.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 20ea60ca ]

Now the vti_link_ops do not point the .dellink, for fb tunnel device
(ip_vti0), the net_device will be removed as the default .dellink is
unregister_netdevice_queue,but the tunnel still in the tunnel list,
then if we add a new vti tunnel, in ip_tunnel_find():

        hlist_for_each_entry_rcu(t, head, hash_node) {
                if (local == t->parms.iph.saddr &&
                    remote == t->parms.iph.daddr &&
                    link == t->parms.link &&
==>                 type == t->dev->type &&
                    ip_tunnel_key_match(&t->parms, flags, key))
                        break;
        }

the panic will happen, cause dev of ip_tunnel *t is null:
[ 3835.072977] IP: [<ffffffffa04103fd>] ip_tunnel_find+0x9d/0xc0 [ip_tunnel]
[ 3835.073008] PGD b2c21067 PUD b7277067 PMD 0
[ 3835.073008] Oops: 0000 [#1] SMP
.....
[ 3835.073008] Stack:
[ 3835.073008]  ffff8800b72d77f0 ffffffffa0411924 ffff8800bb956000 ffff8800b72d78e0
[ 3835.073008]  ffff8800b72d78a0 0000000000000000 ffffffffa040d100 ffff8800b72d7858
[ 3835.073008]  ffffffffa040b2e3 0000000000000000 0000000000000000 0000000000000000
[ 3835.073008] Call Trace:
[ 3835.073008]  [<ffffffffa0411924>] ip_tunnel_newlink+0x64/0x160 [ip_tunnel]
[ 3835.073008]  [<ffffffffa040b2e3>] vti_newlink+0x43/0x70 [ip_vti]
[ 3835.073008]  [<ffffffff8150d4da>] rtnl_newlink+0x4fa/0x5f0
[ 3835.073008]  [<ffffffff812f68bb>] ? nla_strlcpy+0x5b/0x70
[ 3835.073008]  [<ffffffff81508fb0>] ? rtnl_link_ops_get+0x40/0x60
[ 3835.073008]  [<ffffffff8150d11f>] ? rtnl_newlink+0x13f/0x5f0
[ 3835.073008]  [<ffffffff81509cf4>] rtnetlink_rcv_msg+0xa4/0x270
[ 3835.073008]  [<ffffffff8126adf5>] ? sock_has_perm+0x75/0x90
[ 3835.073008]  [<ffffffff81509c50>] ? rtnetlink_rcv+0x30/0x30
[ 3835.073008]  [<ffffffff81529e39>] netlink_rcv_skb+0xa9/0xc0
[ 3835.073008]  [<ffffffff81509c48>] rtnetlink_rcv+0x28/0x30
....

modprobe ip_vti
ip link del ip_vti0 type vti
ip link add ip_vti0 type vti
rmmod ip_vti

do that one or more times, kernel will panic.

fix it by assigning ip_tunnel_dellink to vti_link_ops' dellink, in
which we skip the unregister of fb tunnel device. do the same on ip6_vti.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit aad0b624 upstream.

irq_of_parse_and_map() returns 0 on error (the result is unsigned int),
so testing for negative result never works.
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 2b21ef0a upstream.

Just like 0x1600 which got blacklisted by 66a7cbc3 ("ahci: disable
MSI instead of NCQ on Samsung pci-e SSDs on macbooks"), 0xa800 chokes
on NCQ commands if MSI is enabled.  Disable MSI.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Dominik Mierzejewski <dominik@greysector.net>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=89171Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 249cd0a1 upstream.

This patch adds DeviceIDs for Sunrise Point-LP.
Signed-off-by: Devin Ryles <devin.ryles@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 8e71a322 upstream.

If a device is halted and reuturns a STALL, then the halted endpoint
needs to be cleared both on the host and device side. The host
side halt is cleared by issueing a xhci reset endpoint command. The device side
is cleared with a ClearFeature(ENDPOINT_HALT) request, which should
be issued by the device driver if a URB reruen -EPIPE.

Previously we cleared the host side halt after the device side was cleared.
To make sure the host side halt is cleared in time we want to issue the
reset endpoint command immedialtely when a STALL status is encountered.

Otherwise we end up not following the specs and not returning -EPIPE
several times in a row when trying to transfer data to a halted endpoint.

Fixes: bcef3fd5 (USB: xhci: Handle errors that cause endpoint halts.)
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit b31eb901 upstream.

Setting a non-settable selection target caused BUG() to be called. The check
for valid selections only takes the selection target into account, but does
not tell whether it may be set, or only get. Fix the issue by simply
returning an error to the user.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit e2e68ae6 upstream.

commit e6023367 'x86, kaslr: Prevent .bss from overlaping initrd'
broke the cross compile of x86. It added a objdump invocation, which
invokes the host native objdump and ignores an active cross tool
chain.

Use $(OBJDUMP) instead which takes the CROSS_COMPILE prefix into
account.

[ tglx: Massage changelog and use $(OBJDUMP) ]

Fixes: e6023367 'x86, kaslr: Prevent .bss from overlaping initrd'
Signed-off-by: Chris Clayton <chris2553@googlemail.com>
Acked-by: Kees Cook <keescook@chromium.org>
Acked-by: Borislav Petkov <bp@suse.de>
Cc: Junjie Mao <eternal.n08@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: H. Peter Anvin <hpa@linux.intel.com>
Link: http://lkml.kernel.org/r/54705C8E.1080400@googlemail.comSigned-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit b0616c53 upstream.

Otherwise we'll have backtraces in assert_panel_unlocked because the
BIOS locks the register. In the reporter's case this regression was
introduced in

commit c31407a3
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date:   Thu Oct 18 21:07:01 2012 +0100

    drm/i915: Add no-lvds quirk for Supermicro X7SPA-H
Reported-by: Alexey Orishko <alexey.orishko@gmail.com>
Cc: Alexey Orishko <alexey.orishko@gmail.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Francois Tigeot <ftigeot@wolfpond.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Tested-by: Alexey Orishko <alexey.orishko@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit b6836227 upstream.

Apparently PCH fifo underruns are tricky, we have plenty reports that
we see the occasional underrun (especially at boot-up).

So for a change let's see what happens when we don't re-enable pch
fifo underrun reporting when the pipe is disabled. This means that the
kernel can't catch pch fifo underruns when they happen (except when
all pipes are on on the pch). But we'll still catch underruns when
disabling the pipe again. So not a terrible reduction in test
coverage.

Since the DRM_ERROR is new and hence a regression plan B would be to
revert it back to a debug output. Which would be a lot worse than this
hack for underrun test coverage in the wild. See the referenced
discussions for more.

References: http://mid.gmane.org/CA+gsUGRfGe3t4NcjdeA=qXysrhLY3r4CEu7z4bjTwxi1uOfy+g@mail.gmail.com
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=85898
References: https://bugs.freedesktop.org/show_bug.cgi?id=85898
References: https://bugs.freedesktop.org/show_bug.cgi?id=86233
References: https://bugs.freedesktop.org/show_bug.cgi?id=86478Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Tested-by: lu hua <huax.lu@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit f5475cc4 upstream.

I was unable too boot 3.18.0-rc6 because of the following kernel
panic in drm_calc_vbltimestamp_from_scanoutpos():

    [drm] Initialized drm 1.1.0 20060810
    [drm] radeon kernel modesetting enabled.
    [drm] initializing kernel modesetting (RV100 0x1002:0x515E 0x15D9:0x8080).
    [drm] register mmio base: 0xC8400000
    [drm] register mmio size: 65536
    radeon 0000:0b:01.0: VRAM: 128M 0x00000000D0000000 - 0x00000000D7FFFFFF (16M used)
    radeon 0000:0b:01.0: GTT: 512M 0x00000000B0000000 - 0x00000000CFFFFFFF
    [drm] Detected VRAM RAM=128M, BAR=128M
    [drm] RAM width 16bits DDR
    [TTM] Zone  kernel: Available graphics memory: 3829346 kiB
    [TTM] Zone   dma32: Available graphics memory: 2097152 kiB
    [TTM] Initializing pool allocator
    [TTM] Initializing DMA pool allocator
    [drm] radeon: 16M of VRAM memory ready
    [drm] radeon: 512M of GTT memory ready.
    [drm] GART: num cpu pages 131072, num gpu pages 131072
    [drm] PCI GART of 512M enabled (table at 0x0000000037880000).
    radeon 0000:0b:01.0: WB disabled
    radeon 0000:0b:01.0: fence driver on ring 0 use gpu addr 0x00000000b0000000 and cpu addr 0xffff8800bbbfa000
    [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
    [drm] Driver supports precise vblank timestamp query.
    [drm] radeon: irq initialized.
    [drm] Loading R100 Microcode
    radeon 0000:0b:01.0: Direct firmware load for radeon/R100_cp.bin failed with error -2
    radeon_cp: Failed to load firmware "radeon/R100_cp.bin"
    [drm:r100_cp_init] *ERROR* Failed to load firmware!
    radeon 0000:0b:01.0: failed initializing CP (-2).
    radeon 0000:0b:01.0: Disabling GPU acceleration
    [drm] radeon: cp finalized
    BUG: unable to handle kernel NULL pointer dereference at 000000000000025c
    IP: [<ffffffff8150423b>] drm_calc_vbltimestamp_from_scanoutpos+0x4b/0x320
    PGD 0
    Oops: 0000 [#1] SMP
    Modules linked in:
    CPU: 1 PID: 1 Comm: swapper/0 Not tainted 3.18.0-rc6-4-default #2649
    Hardware name: Supermicro X7DB8/X7DB8, BIOS 6.00 07/26/2006
    task: ffff880234da2010 ti: ffff880234da4000 task.ti: ffff880234da4000
    RIP: 0010:[<ffffffff8150423b>]  [<ffffffff8150423b>] drm_calc_vbltimestamp_from_scanoutpos+0x4b/0x320
    RSP: 0000:ffff880234da7918  EFLAGS: 00010086
    RAX: ffffffff81557890 RBX: 0000000000000000 RCX: ffff880234da7a48
    RDX: ffff880234da79f4 RSI: 0000000000000000 RDI: ffff880232e15000
    RBP: ffff880234da79b8 R08: 0000000000000000 R09: 0000000000000000
    R10: 000000000000000a R11: 0000000000000001 R12: ffff880232dda1c0
    R13: ffff880232e1518c R14: 0000000000000292 R15: ffff880232e15000
    FS:  0000000000000000(0000) GS:ffff88023fc40000(0000) knlGS:0000000000000000
    CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
    CR2: 000000000000025c CR3: 0000000002014000 CR4: 00000000000007e0
    Stack:
     ffff880234da79d8 0000000000000286 ffff880232dcbc00 0000000000002480
     ffff880234da7958 0000000000000296 ffff880234da7998 ffffffff8151b51d
     ffff880234da7a48 0000000032dcbeb0 ffff880232dcbc00 ffff880232dcbc58
    Call Trace:
     [<ffffffff8151b51d>] ? drm_vma_offset_remove+0x1d/0x110
     [<ffffffff8152dc98>] radeon_get_vblank_timestamp_kms+0x38/0x60
     [<ffffffff8152076a>] ? ttm_bo_release_list+0xba/0x180
     [<ffffffff81503751>] drm_get_last_vbltimestamp+0x41/0x70
     [<ffffffff81503933>] vblank_disable_and_save+0x73/0x1d0
     [<ffffffff81106b2f>] ? try_to_del_timer_sync+0x4f/0x70
     [<ffffffff81505245>] drm_vblank_cleanup+0x65/0xa0
     [<ffffffff815604fa>] radeon_irq_kms_fini+0x1a/0x70
     [<ffffffff8156c07e>] r100_init+0x26e/0x410
     [<ffffffff8152ae3e>] radeon_device_init+0x7ae/0xb50
     [<ffffffff8152d57f>] radeon_driver_load_kms+0x8f/0x210
     [<ffffffff81506965>] drm_dev_register+0xb5/0x110
     [<ffffffff8150998f>] drm_get_pci_dev+0x8f/0x200
     [<ffffffff815291cd>] radeon_pci_probe+0xad/0xe0
     [<ffffffff8141a365>] local_pci_probe+0x45/0xa0
     [<ffffffff8141b741>] pci_device_probe+0xd1/0x130
     [<ffffffff81633dad>] driver_probe_device+0x12d/0x3e0
     [<ffffffff8163413b>] __driver_attach+0x9b/0xa0
     [<ffffffff816340a0>] ? __device_attach+0x40/0x40
     [<ffffffff81631cd3>] bus_for_each_dev+0x63/0xa0
     [<ffffffff8163378e>] driver_attach+0x1e/0x20
     [<ffffffff81633390>] bus_add_driver+0x180/0x240
     [<ffffffff81634914>] driver_register+0x64/0xf0
     [<ffffffff81419cac>] __pci_register_driver+0x4c/0x50
     [<ffffffff81509bf5>] drm_pci_init+0xf5/0x120
     [<ffffffff821dc871>] ? ttm_init+0x6a/0x6a
     [<ffffffff821dc908>] radeon_init+0x97/0xb5
     [<ffffffff810002fc>] do_one_initcall+0xbc/0x1f0
     [<ffffffff810e3278>] ? __wake_up+0x48/0x60
     [<ffffffff8218e256>] kernel_init_freeable+0x18a/0x215
     [<ffffffff8218d983>] ? initcall_blacklist+0xc0/0xc0
     [<ffffffff818a78f0>] ? rest_init+0x80/0x80
     [<ffffffff818a78fe>] kernel_init+0xe/0xf0
     [<ffffffff818c0c3c>] ret_from_fork+0x7c/0xb0
     [<ffffffff818a78f0>] ? rest_init+0x80/0x80
    Code: 45 ac 0f 88 a8 01 00 00 3b b7 d0 01 00 00 49 89 ff 0f 83 99 01 00 00 48 8b 47 20 48 8b 80 88 00 00 00 48 85 c0 0f 84 cd 01 00 00 <41> 8b b1 5c 02 00 00 41 8b 89 58 02 00 00 89 75 98 41 8b b1 60
    RIP  [<ffffffff8150423b>] drm_calc_vbltimestamp_from_scanoutpos+0x4b/0x320
     RSP <ffff880234da7918>
    CR2: 000000000000025c
    ---[ end trace ad2c0aadf48e2032 ]---
    Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000009

It has helped me to add a NULL pointer check that was suggested at
http://lists.freedesktop.org/archives/dri-devel/2014-October/070663.html

I am not familiar with the code. But the change looks sane
and we need something fast at this stage of 3.18 development.
Suggested-by: Helge Deller <deller@gmx.de>
Signed-off-by: Petr Mladek <pmladek@suse.cz>
Tested-by: Petr Mladek <pmladek@suse.cz>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 9ea359f7 upstream.

According to I2C specification the NACK should be handled as follows:
"When SDA remains HIGH during this ninth clock pulse, this is defined as the Not
Acknowledge signal. The master can then generate either a STOP condition to
abort the transfer, or a repeated START condition to start a new transfer."
[I2C spec Rev. 6, 3.1.6: http://www.nxp.com/documents/user_manual/UM10204.pdf]

Currently the Davinci i2c driver interrupts the transfer on receipt of a
NACK but fails to send a STOP in some situations and so makes the bus
stuck until next I2C IP reset (idle/enable).

For example, the issue will happen during SMBus read transfer which
consists from two i2c messages write command/address and read data:

S Slave Address Wr A Command Code A Sr Slave Address Rd A D1..Dn A P
<--- write -----------------------> <--- read --------------------->

The I2C client device will send NACK if it can't recognize "Command Code"
and it's expected from I2C master to generate STP in this case.
But now, Davinci i2C driver will just exit with -EREMOTEIO and STP will
not be generated.

Hence, fix it by generating Stop condition (STP) always when NACK is received.

This patch fixes Davinci I2C in the same way it was done for OMAP I2C
commit cda2109a ("i2c: omap: query STP always when NACK is received").
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reported-by: Hein Tibosch <hein_tibosch@yahoo.es>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit ccfc8663 upstream.

commit 6d9939f6 (i2c: omap: split out [XR]DR
and [XR]RDY) changed the way how errata i207 (I2C: RDR Flag May Be Incorrectly
Set) get handled. 6d9939f6 code doesn't correspond to workaround provided by
errata.

According to errata ISR must filter out spurious RDR before data read not after.
ISR must read RXSTAT to get number of bytes available to read. Because RDR
could be set while there could no data in the receive FIFO.

Restored pre 6d9939f6 way of handling errata.

Found by code review. Real impact haven't seen.
Tested on Beagleboard XM C.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Fixes: 6d9939f6 i2c: omap: split out [XR]DR and [XR]RDY
Tested-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 27caca9d upstream.

commit 1d7afc95 (i2c: omap: ack IRQ in parts)
changed the interrupt handler to complete transfers without clearing
XRDY (AL case) and ARDY (NACK case) flags. XRDY or ARDY interrupts will be
fired again. As a result, ISR keep processing transfer after it was already
complete (from the driver code point of view).

A didn't see real impacts of the 1d7afc95, but it is really bad idea to
have ISR running on user data after transfer was complete.

It looks, what 1d7afc95 violate TI specs in what how AL and NACK should be
handled (see Note 1, sprugn4r, Figure 17-31 and Figure 17-32).

According to specs (if I understood correctly), in case of NACK and AL driver
must reset NACK, AL, ARDY, RDR, and RRDY (Master Receive Mode), and
NACK, AL, ARDY, and XDR (Master Transmitter Mode).

All that is done down the code under the if condition:
if (stat & (OMAP_I2C_STAT_ARDY | OMAP_I2C_STAT_NACK | OMAP_I2C_STAT_AL)) ...

The patch restore pre 1d7afc95 logic of handling NACK and AL interrupts, so
no interrupts is fired after ISR informs the rest of driver what transfer
complete.

Note: instead of removing break under NACK case, we could just replace 'break'
with 'continue' and allow NACK transfer to finish using ARDY event. I found
that NACK and ARDY bits usually set together. That case confirm TI wiki:
http://processors.wiki.ti.com/index.php/I2C_Tips#Detecting_and_handling_NACK

In order if someone interested in the event traces for NACK and AL cases,
I sent them to mailing list.

Tested on Beagleboard XM C.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Fixes: 1d7afc95 i2c: omap: ack IRQ in parts
Acked-by: Felipe Balbi <balbi@ti.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 8d609725 upstream.

These BUGs can be erroneously triggered by frags which refer to
tail pages within a compound page. The data in these pages may
overrun the hardware page while still being contained within the
compound page, but since compound_order() evaluates to 0 for tail
pages the assertion fails. The code already iterates through
subsequent pages correctly in this scenario, so the BUGs are
unnecessary and can be removed.

Fixes: f36c3747 ("xen/netfront: handle compound page fragments on transmit")
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Reviewed-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit c4ea95d7 upstream.

Andrew Morton noticed that the error return from anon_vma_clone() was
being dropped and replaced with -ENOMEM (which is not itself a bug
because the only error return value from anon_vma_clone() is -ENOMEM).

I did an audit of callers of anon_vma_clone() and discovered an actual
bug where the error return was being lost.  In __split_vma(), between
Linux 3.11 and 3.12 the code was changed so the err variable is used
before the call to anon_vma_clone() and the default initial value of
-ENOMEM is overwritten.  So a failure of anon_vma_clone() will return
success since err at this point is now zero.

Below is a patch which fixes this bug and also propagates the error
return value from anon_vma_clone() in all cases.

Fixes: ef0855d3 ("mm: mempolicy: turn vma_set_policy() into vma_dup_policy()")
Signed-off-by: Daniel Forrest <dan.forrest@ssec.wisc.edu>
Reviewed-by: Michal Hocko <mhocko@suse.cz>
Cc: Konstantin Khlebnikov <koct9i@gmail.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Tim Hartrick <tim@edgecast.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Michel Lespinasse <walken@google.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 2022b4d1 upstream.

I've been seeing swapoff hangs in recent testing: it's cycling around
trying unsuccessfully to find an mm for some remaining pages of swap.

I have been exercising swap and page migration more heavily recently,
and now notice a long-standing error in copy_one_pte(): it's trying to
add dst_mm to swapoff's mmlist when it finds a swap entry, but is doing
so even when it's a migration entry or an hwpoison entry.

Which wouldn't matter much, except it adds dst_mm next to src_mm,
assuming src_mm is already on the mmlist: which may not be so.  Then if
pages are later swapped out from dst_mm, swapoff won't be able to find
where to replace them.

There's already a !non_swap_entry() test for stats: move that up before
the swap_duplicate() and the addition to mmlist.
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: Kelley Nielsen <kelleynnn@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 91b57191 upstream.

In some android devices, there will be a "divide by zero" exception.
vmpr->scanned could be zero before spin_lock(&vmpr->sr_lock).

Addresses https://bugzilla.kernel.org/show_bug.cgi?id=88051

[akpm@linux-foundation.org: neaten]
Reported-by: ji_ang <ji_ang@163.com>
Cc: Anton Vorontsov <anton.vorontsov@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit fb993fa1 upstream.

If a frontswap dup-store failed, it should invalidate the expired page
in the backend, or it could trigger some data corruption issue.
Such as:
 1. use zswap as the frontswap backend with writeback feature
 2. store a swap page(version_1) to entry A, success
 3. dup-store a newer page(version_2) to the same entry A, fail
 4. use __swap_writepage() write version_2 page to swapfile, success
 5. zswap do shrink, writeback version_1 page to swapfile
 6. version_2 page is overwrited by version_1, data corrupt.

This patch fixes this issue by invalidating expired data immediately
when meet a dup-store failure.
Signed-off-by: Weijie Yang <weijie.yang@samsung.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Seth Jennings <sjennings@variantweb.net>
Cc: Dan Streetman <ddstreet@ieee.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Bob Liu <bob.liu@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 92a56555 upstream.

If a SIGKILL is sent to a task waiting in __nfs_iocounter_wait,
it will busy-wait or soft lockup in its while loop.
nfs_wait_bit_killable won't sleep, and the loop won't exit on
the error return.

Stop the busy-wait by breaking out of the loop when
nfs_wait_bit_killable returns an error.
Signed-off-by: David Jeffery <djeffery@redhat.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
[ kamal: backport to 3.13-stable: context ]
Cc: Moritz Mühlenhoff <muehlenhoff@univention.de>
Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit c1118b36 upstream.

On x86_64, kernel text mappings are mapped read-only with CONFIG_DEBUG_RODATA.
In that case, KVM will fail to patch VMCALL instructions to VMMCALL
as required on AMD processors.

The failure mode is currently a divide-by-zero exception, which obviously
is a KVM bug that has to be fixed.  However, picking the right instruction
between VMCALL and VMMCALL will be faster and will help if you cannot upgrade
the hypervisor.
Reported-by: Chris Webb <chris@arachsys.com>
Tested-by: Chris Webb <chris@arachsys.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: x86@kernel.org
Acked-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Chris J Arges <chris.j.arges@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit b6ed5498 upstream.

batman tries to search dev->iflink to check if it's a batman interface,
but ->iflink could be 0, which is not a valid ifindex. It should just
avoid iflink == 0 case.
Reported-by: Jet Chen <jet.chen@intel.com>
Tested-by: Jet Chen <jet.chen@intel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: Antonio Quartulli <antonio@open-mesh.com>
Cc: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 36074381 upstream.

Instead of the arch specific quirk which we are deprecating
and that drivers don't understand.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 8c3cac5e upstream.

A leftover lock on the list is surely a sign of a problem of some sort,
but it's not necessarily a reason to panic the box. Instead, just log a
warning with some info about the lock, and then delete it like we would
any other lock.

In the event that the filesystem declares a ->lock f_op, we may end up
leaking something, but that's generally preferable to an immediate
panic.
Acked-by: J. Bruce Fields <bfields@fieldses.org>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Cc: Markus Blank-Burian <burian@muenster.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 00b4d9a1 upstream.

On some 32 bits architectures, including x86, GENMASK(31, 0) returns 0
instead of the expected ~0UL.

This is the same on some 64 bits architectures with GENMASK_ULL(63, 0).

This is due to an overflow in the shift operand, 1 << 32 for GENMASK,
1 << 64 for GENMASK_ULL.
Reported-by: Eric Paire <eric.paire@st.com>
Suggested-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: linux@rasmusvillemoes.dk
Cc: gong.chen@linux.intel.com
Cc: John Sullivan <jsrhbz@kanargh.force9.co.uk>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Fixes: 10ef6b0d ("bitops: Introduce a more generic BITMASK macro")
Link: http://lkml.kernel.org/r/1415267659-10563-1-git-send-email-maxime.coquelin@st.comSigned-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 91ed6fd2 upstream.

Some radeon ASICs don't support all 64 address bits of MSIs despite
advertising support for 64-bit MSIs in their configuration space.

This breaks on systems such as IBM POWER7/8, where 64-bit MSIs can
be assigned with some of the high address bits set.

This makes use of the newly introduced "no_64bit_msi" flag in structure
pci_dev to allow the MSI allocation code to fallback to 32-bit MSIs
on those adapters.

Adding Alex's review tag. Patch to the driver is identical to the
reviewed one, I dropped the arch/powerpc hunk rewrote the subject
and cset comment.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 28731d58 upstream.

Value needs to be swapped on BE.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>