Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Sameeh Jubran <sameehj@amazon.com>
Acked-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Let netdev_stats_to_stats64() do the copy work for us.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Clearing opts2 belongs to preparing the descriptor for DMA engine use.
Therefore move it into rtl8169_mark_to_asic().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
100GbE Intel Wired LAN Driver Updates 2020-03-10

This series contains updates to ice and iavf drivers.

Cleaned up unnecessary parenthesis, which was pointed out by Sergei
Shtylyov.

Mitch updates the iavf and ice drivers to expand the limitation on the
number of queues that the driver can support to account for the newer
800-series capabilities.

Brett cleans up the error messages for both SR-IOV and non SR-IOV use
cases.  Fixed the logic when the ice driver is removed and a bare-metal
VF is passing traffic, which was causing a transmit hang on the VF.
Updated the ice driver to display "Link detected" field via ethtool,
when the driver is in safe mode.  Updated ice driver to properly set
VLAN pruning when transmit anti-spoof is off.

Avinash fixed a corner case in DCB, when switching from IEEE to CEE
mode, the DCBX mode does not get properly updated.

Dave updates the logic when switching from software DCB to firmware DCB
to renegotiate DCBX to ensure the firmware agent has up to date
information about the DCB settings of the link partner.

Lukasz increases the PF's mailbox receive queue size to the maximum to
prevent potential bottleneck or slow down occurring from the PF's
mailbox receive queue being full.

Bruce updates the ice driver to use strscpy() instead of strlcpy().
Cleaned up variable names that were not very descriptive with names that
had more meaning.

Anirudh replaces the use of ENOTSUPP with EOPNOTSUPP in the ice driver.

Jake fixed up a function header comment to properly reflect the variable
size and use.

v2: Dropped patch 5 of the original series, where Tony added tunnel
    offload support.  Based on community feedback, the patch needed
    changes, so giving Tony additional time to work on those changes and
    not hold up the remaining changes in the series.
====================
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The inner pair of parentheses should be around the variable x

Fixes: 37feab60 ("net: dsa: mt7530: add support for port mirroring")
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Simplify ksz_common.c by using delayed_work instead of a combination of
timer and work.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jiri Pirko says:

====================
flow_offload: follow-ups to HW stats type patchset

This patchset includes couple of patches in reaction to the discussions
to the original HW stats patchset. The first patch is a fix,
the other two patches are basically cosmetics.
====================
Acked-by: Edward Cree <ecree@solarflare.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The intention of this helper was to allow driver to specify one type
that it supports, so not only "any" value would pass. So make the API
more strict and allow driver to pass only 1 bit that is going
to be checked.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

Put the values into enum and add an enum to define the bits.
Suggested-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

Change the check to see if the passed allowed type bit is enabled.

Fixes: 319a1d19 ("flow_offload: check for basic action hw stats type")
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

Claudiu Manoil says:

====================
enetc: Support extended BD rings at runtime

First two patches are just misc code cleanup.
The 3rd patch prepares the Rx BD processing code to be extended
to processing both normal and extended BDs.
The last one adds extended Rx BD support for timestamping
without the need of a static config. Finally, the config option
FSL_ENETC_HW_TIMESTAMPING can be dropped.
Care was taken not to impact non-timestamping usecases.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Hardware timestamping support (PTP) on Rx requires extended
buffer descriptors, double the size of normal Rx descriptors.
On the current controller revision only the timestamping offload
requires extended Rx descriptors.
Since Rx timestamping can be turned on/off at runtime, make Rx ring
allocation configurable at runtime too. As a result, the static
config option FSL_ENETC_HW_TIMESTAMPING can be dropped and the
extended descriptors can be used only when Rx timestamping gets
activated.
The extension has the same size as the base descriptor, making
the descriptor iterators easy to update for the extended case.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Improve maintainability of the code iterating the Rx buffer
descriptors to prepare it to support iterating extended Rx BD
descriptors as well.
Don't increment by one the h/w descriptor pointers explicitly,
provide an iterator that takes care of the h/w details.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Refactor the stats len computation code to make it easier
to add new stats counters.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The existence of the DT port node is the first thing checked
at probe time, and probing won't reach this point if the node
is missing.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When pktgen is used to measure the performance of dev_queue_xmit()
packet handling in the core, it is preferable to not hand down
packets to a low-level Ethernet driver as it would distort the
measurements.

Allow using pktgen on the loopback device, thus constraining
measurements to core code.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Instead of manually iterating over entries, use flow_action_for_each
helper. Move the helper and wrap it to fit to 80 cols on the way.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The function comment for ice_get_nvm_version indicated that the ver_hi
and ver_lo values were 16 bits. In fact, they are only uint8_t values,
meaning that they have a maximum size of 8 bits. Fix the comment to
match the correct size.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The variable name 'type' is not very descriptive. Replace instances of
those with a variable name that is more descriptive or replace it if not
needed.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Using ENOTSUPP almost always results in some bizarre error message to
be printed in userspace. This is likely because ENOTSUPP was defined for
the NFS protocol (as per a comment in include/linux/errno.h). Use
EOPNOTSUPP instead.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Commit ed5a3f66 ("ice: Removing hung_queue variable to use txqueue
function parameter") began utilizing the txqueue variable over the
hung_queue variable. hung_queue was an int where txqueue is an unsigned
int. Update the format specifiers to reflect the new type.

Fixes: ed5a3f66 ("ice: Removing hung_queue variable to use txqueue function parameter")
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

checkpatch complains "CHECK:DEPRECATED_API: Deprecated use of 'strlcpy',
prefer 'stracpy or strscpy' instead"; use strscpy.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently the PF's mailbox receive queue is only 512 entries. This fine,
but considering that all VF's mailbox send queues funnel into the PF's
single mailbox receive queue, let's increase it to the maximum size. This
will help prevent any possible bottleneck/slowdown occurring from the PF's
mailbox receive queue being full.
Signed-off-by: Lukasz Czapnik <lukasz.czapnik@intel.com>
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

VLAN pruning is not always being set correctly due to a previous change
that set Tx antispoof off. ice_vsi_is_vlan_pruning_ena() currently checks
for both Tx antispoof and Rx pruning. The expectation for this function is
to only check Rx pruning so fix the check.

Fixes: cd6d6b83 ("ice: Fix VF spoofchk")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

When switching from SW DCB to FW DCB it is necessary
to renegotiate DCBx so that the FW agent can have up
to date information about the DCB settings of the link
partner.

Perform an autoneg restart on the link when activating
FW DCB.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

While testing DCB for a corner case in which mode is switched from IEEE to
CEE and pfc_ena bitmask unchanged then DCBX mode doesn't get updated.

This is happening because the function ice_dcb_get_mode() is called
in a "no change detected block" instead of "change detected block".
Signed-off-by: Avinash JD <avinash.dayanand@intel.com>
Signed-off-by: Scott Register <scottx.register@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently the "Link detected" field is not shown when the device goes
into safe mode. This is because the safe mode Ethtool ops does not set the
get_link function. Fix this by setting the safe mode Ethtool op get_link
function.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently, if there are bare-metal VFs passing traffic and the ice
driver is removed, there is a possibility of VFs triggering a Tx timeout
right before iavf_remove(). This is causing iavf_close() to not be
called because there is a check in the beginning of iavf_remove() that
bails out early if (adapter->state < IAVF_DOWN_PENDING). This makes it
so some resources do not get cleaned up. Specifically, free_irq()
is never called for data interrupts, which results in the following line
of code to trigger:

pci_disable_msix()
	free_msi_irqs()
		...
		BUG_ON(irq_has_action(entry->irq + i));
		...

To prevent the Tx timeout from occurring on the VF during driver unload
for ice and the iavf there are a few changes that are needed.

[1] Don't disable all active VF Tx/Rx queues prior to calling
pci_disable_sriov.

[2] Call ice_free_vfs() before disabling the service task.

[3] Disable VF resets when the ice driver is being unloaded by setting
the pf->state flag __ICE_VF_RESETS_DISABLED.

Changing [1] and [2] allow each VF driver's remove flow to successfully
send VIRTCHNL requests, which includes queue disable. This prevents
unexpected Tx timeouts because the PF driver is no longer forcefully
disabling queues.

Due to [1] and [2] there is a possibility that the PF driver will get a
VFLR or reset request over VIRTCHNL from a VF during PF driver unload.
Prevent that by doing [3].
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently when the device runs out of MSI-X interrupts a cryptic and
unhelpful message is printed. This will cause confusion when hitting this
case. Fix this by clearing up the error message for both SR-IOV and non
SR-IOV use cases.

Also, make a few minor changes to increase clarity of variables.
1. Change per VF MSI-X and queue pair variables in the PF structure.
2. Use ICE_NONQ_VECS_VF when determining pf->num_msix_per_vf instead of
the magic number "1". This vector is reserved for the OICR.

All of the resource tracking functions were moved to avoid adding
any forward declaration function prototypes.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Unlike the XL710 series, 800-series hardware can allocate more than 4
MSI-X vectors per VF. This patch enables that functionality. We
dynamically allocate vectors and queues depending on how many VFs are
enabled. Allocating the maximum number of VFs replicates XL710
behavior with 4 queues and 4 vectors. But allocating a smaller number
of VFs will give you 16 queues and 16 vectors.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Previous devices could only allocate 4 MSI-X vectors per VF so there was a
limitation of 4 queues. 800-series hardware can allocate more than 4 MSI-X
vectors, so expand the limitation on the number of queues that the driver
can support to account for these capabilities.

Fix ethtool channel operations to accommodate this change and adjust the
reporting of max number of queues to what is given to us by the PF. Since
we're not requesting queues above this value, just trigger reset to
activate the queues, which we already own.

Finally, fix a test condition that would display an incorrect error
message.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Sergei Shtylyov pointed out that two instances of parenthesis are not
needed, so remove them.
Suggested-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>

Jose Abreu says:

====================
net: Add support for Synopsys DesignWare XPCS

This adds support for Synopsys DesignWare XPCS in net subsystem and
integrates it into stmmac.

At 1/8, we start by removing the limitation of stmmac selftests that needed
a PHY to pass all the tests.

Then at 2/8 we use some helpers in stmmac so that some code can be
simplified.

At 3/8, we fallback to dev_fwnode() so that PCI based setups wich may
not have CONFIG_OF can still use FW node.

At 4/8, we adapt stmmac to the new PHYLINK changes as suggested by Russell
King.

We proceed by doing changes in PHYLINK in order to support XPCS: At 5/8 we
add some missing speeds that USXGMII supports and at 6/8 we check if
Autoneg is supported after initial parameters are validated.

Support for XPCS is finally introduced at 7/8, along with the usage of it
in stmmac driver at 8/8.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Adds all the necessary logic so that stmmac can be used with Synopsys
DesignWare XPCS.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Synopsys DesignWare XPCS is an MMD that can manage link status,
auto-negotiation, link training, ...

In this commit we add basic support for XPCS using USXGMII interface and
Clause 73 Auto-negotiation.

This is highly tied with PHYLINK and can't be used without it. A given
ethernet driver can use the provided callbacks to add the support for
XPCS.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We may have cases where MAC or PCS do not support Autoneg. Check if it
is supported after validate callback is called.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

USXGMII also supports these missing backplane speeds.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Convert the stmmac ethernet driver to use the finalised link parameters
in mac_link_up() rather than the parameters in mac_config().
Suggested-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When CONFIG_OF is not enabled, of_fwnode_handle() will return NULL, even
though we can have a FW handle from a given device.

Fallback to dev_fwnode() helper if needed.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use the linkmode_and()/linkmode_andnot() helpers to simplify the code.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>