Don't sometimes use the address operator and sometimes not. Drop it and
make the code look uniform.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

According to the datasheet of the IP101A/G there is no revision field
and MII_PHYSID2 always reads as 0x0c54. Use PHY_ID_MATCH_EXACT() then.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Simpify the initializations of the structures. There is no functional
change.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

George McCollister says:

====================
add HSR offloading support for DSA switches

Add support for offloading HSR/PRP (IEC 62439-3) tag insertion, tag
removal, forwarding and duplication on DSA switches.
This series adds offloading to the xrs700x DSA driver.

Changes since RFC:
 * Split hsr and dsa patches. (Florian Fainelli)

Changes since v1:
 * Fixed some typos/wording. (Vladimir Oltean)
 * eliminate IFF_HSR and use is_hsr_master instead. (Vladimir Oltean)
 * Make hsr_handle_sup_frame handle skb_std as well (required when offloading)
 * Don't add hsr tag for HSR v0 supervisory frames.
 * Fixed tag insertion offloading for PRP.

Changes since v2:
 * Return -EOPNOTSUPP instead of 0 in dsa_switch_hsr_join and
   dsa_switch_hsr_leave. (Vladimir Oltean)
 * Only allow ports 1 and 2 to be HSR/PRP redundant ports. (Tobias Waldekranz)
 * Set and remove HSR features for both redundant ports. (Vladimir Oltean)
 * Change port_hsr_leave() to return int instead of void.
 * Remove hsr_init_skb() proto argument. (Vladimir Oltean)
===================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add offloading for HSR/PRP (IEC 62439-3) tag insertion, tag removal
forwarding and duplication supported by the xrs7000 series switches.

Only HSR v1 and PRP v1 are supported by the xrs7000 series switches (HSR
v0 is not).
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for offloading of HSR/PRP (IEC 62439-3) tag insertion
tag removal, duplicate generation and forwarding on DSA switches.

Add DSA_NOTIFIER_HSR_JOIN and DSA_NOTIFIER_HSR_LEAVE which trigger calls
to .port_hsr_join and .port_hsr_leave in the DSA driver for the switch.

The DSA switch driver should then set netdev feature flags for the
HSR/PRP operation that it offloads.
    NETIF_F_HW_HSR_TAG_INS
    NETIF_F_HW_HSR_TAG_RM
    NETIF_F_HW_HSR_FWD
    NETIF_F_HW_HSR_DUP
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for offloading of HSR/PRP (IEC 62439-3) tag insertion
tag removal, duplicate generation and forwarding.

For HSR, insertion involves the switch adding a 6 byte HSR header after
the 14 byte Ethernet header. For PRP it adds a 6 byte trailer.

Tag removal involves automatically stripping the HSR/PRP header/trailer
in the switch. This is possible when the switch also performs auto
deduplication using the HSR/PRP header/trailer (making it no longer
required).

Forwarding involves automatically forwarding between redundant ports in
an HSR. This is crucial because delay is accumulated as a frame passes
through each node in the ring.

Duplication involves the switch automatically sending a single frame
from the CPU port to both redundant ports. This is required because the
inserted HSR/PRP header/trailer must contain the same sequence number
on the frames sent out both redundant ports.

Export is_hsr_master so DSA can tell them apart from other devices in
dsa_slave_changeupper.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For a switch to offload insertion of HSR/PRP tags, frames must not be
sent to the CPU facing switch port with a tag. Generate supervision frames
(eth type ETH_P_PRP) without HSR v1 (ETH_P_HSR)/PRP tag and rely on
create_tagged_frame which inserts it later. This will allow skipping the
tag insertion for all outgoing frames in the future which is required for
HSR v1/PRP tag insertions to be offloaded.

HSR v0 supervision frames always contain tag information so insertion of
the tag can't be offloaded. IEC 62439-3 Ed.2.0 (HSR v1) specifically
notes that this was changed since v0 to allow offloading.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use of_match_ptr() on xrs700x_mdio_dt_ids so that NULL is substituted
when CONFIG_OF isn't defined. This will prevent unnecessary use of
xrs700x_mdio_dt_ids when CONFIG_OF isn't defined.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix unused variable warning that occurs when CONFIG_OF isn't defined by
adding __maybe_unused.

>> drivers/net/dsa/xrs700x/xrs700x_i2c.c:127:34: warning: unused
variable 'xrs700x_i2c_dt_ids' [-Wunused-const-variable]
   static const struct of_device_id xrs700x_i2c_dt_ids[] = {
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Eric Dumazet says:

====================
tcp: RFC 6056 induced changes

This is based on a report from David Dworken.

First patch implements RFC 6056 3.3.4 proposal.

Second patch is adding a little bit of noise to make
attacker life a bit harder.
===================
Signed-off-by: David S. Miller <davem@davemloft.net>

Even when implementing RFC 6056 3.3.4 (Algorithm 4: Double-Hash
Port Selection Algorithm), a patient attacker could still be able
to collect enough state from an otherwise idle host.

Idea of this patch is to inject some noise, in the
cases __inet_hash_connect() found a candidate in the first
attempt.

This noise should not significantly reduce the collision
avoidance, and should be zero if connection table
is already well used.

Note that this is not implementing RFC 6056 3.3.5
because we think Algorithm 5 could hurt typical
workloads.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: David Dworken <ddworken@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

RFC 6056 (Recommendations for Transport-Protocol Port Randomization)
provides good summary of why source selection needs extra care.

David Dworken reminded us that linux implements Algorithm 3
as described in RFC 6056 3.3.3

Quoting David :
   In the context of the web, this creates an interesting info leak where
   websites can count how many TCP connections a user's computer is
   establishing over time. For example, this allows a website to count
   exactly how many subresources a third party website loaded.
   This also allows:
   - Distinguishing between different users behind a VPN based on
       distinct source port ranges.
   - Tracking users over time across multiple networks.
   - Covert communication channels between different browsers/browser
       profiles running on the same computer
   - Tracking what applications are running on a computer based on
       the pattern of how fast source ports are getting incremented.

Section 3.3.4 describes an enhancement, that reduces
attackers ability to use the basic information currently
stored into the shared 'u32 hint'.

This change also decreases collision rate when
multiple applications need to connect() to
different destinations.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: David Dworken <ddworken@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In commit c9dca822 ("net-loopback: set lo dev initial state to UP"),
linux started automatically bringing up the loopback device of a newly
created namespace. However, an existing user script might reasonably have
the following stanza when creating a new namespace -- and in fact at least
tools/testing/selftests/net/fib_nexthops.sh in Linux's very own testsuite
does:

 # set -e
 # ip netns add foo
 # ip -netns foo addr add 127.0.0.1/8 dev lo
 # ip -netns foo link set lo up
 # set +e

This will now fail, because the kernel reasonably rejects "ip addr add" of
a duplicate address. The described change of behavior therefore constitutes
a breakage. Revert it.

Fixes: c9dca822 ("net-loopback: set lo dev initial state to UP")
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

At the moment, PORT_MII is reported in the ethtool ops. This is odd
because it is an interface between the MAC and the PHY and no external
port. Some network card drivers will overwrite the port to twisted pair
or fiber, though. Even worse, the MDI/MDIX setting is only used by
ethtool if the port is twisted pair.

Set the port to PORT_TP by default because most PHY drivers are copper
ones. If there is fibre support and it is enabled, the PHY driver will
set it to PORT_FIBRE.

This will change reporting PORT_MII to either PORT_TP or PORT_FIBRE;
except for the genphy fallback driver.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

%s/dest_mac_filter/dmac_filter/g

Fixes: e78ab164 ("devlink: Add DMAC filter generic packet trap")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reported-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Lijun Pan says:

====================
ibmvnic: a set of fixes of coding style

This series address several coding style problems.

v2: rebased on top of tree. Add the Reviewed-by tag from v1 reviews.
    patch 8/8 is new.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix this warning:
WARNING: Prefer strscpy over strlcpy - see: https://lore.kernel.org/r/CAHk-=wgfRnXz0W3D37d01q3JFkr_i_uTL=V6A6G1oUZcprmknw@mail.gmail.com/Signed-off-by: Lijun Pan <lijunp213@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

stats_lock is no longer used. So remove it.
Signed-off-by: Lijun Pan <lijunp213@gmail.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There are several spinlock_t definitions without comments.
Add them.
Signed-off-by: Lijun Pan <lijunp213@gmail.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix the following checkpatch checks:
CHECK: Macro argument 'off' may be better as '(off)' to
avoid precedence issues
CHECK: Alignment should match open parenthesis
CHECK: multiple assignments should be avoided
CHECK: Blank lines aren't necessary before a close brace '}'
CHECK: Please use a blank line after function/struct/union/enum
declarations
CHECK: Unnecessary parentheses around 'rc != H_FUNCTION'
Signed-off-by: Lijun Pan <lijunp213@gmail.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix the following checkpatch warning:
WARNING: Avoid multiple line dereference
Signed-off-by: Lijun Pan <lijunp213@gmail.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix the following checkpatch warning:
WARNING: braces {} are not necessary for single statement blocks
Signed-off-by: Lijun Pan <lijunp213@gmail.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix the following checkpatch warning:
WARNING: networking block comments don't use an empty /* line, use /* Comment...
Signed-off-by: Lijun Pan <lijunp213@gmail.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix the following checkpatch warnings:
WARNING: Prefer 'unsigned long' over 'unsigned long int' as the int is unnecessary
WARNING: Prefer 'long' over 'long int' as the int is unnecessary
Signed-off-by: Lijun Pan <lijunp213@gmail.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Tony Nguyen says:

====================
40GbE Intel Wired LAN Driver Updates 2021-02-10

This series contains updates to i40e driver only.

Arkadiusz adds support for software controlled DCB. Upon disabling of the
firmware LLDP agent, the driver configures DCB with default values
(only one Traffic Class). At the same time, it allows a software based
LLDP agent - userspace application i.e. lldpad) to receive DCB TLVs
and set desired DCB configuration through DCB related netlink callbacks.

Aleksandr implements get and set ethtool ops for Energy Efficient
Ethernet.

Przemyslaw extends support for ntuple filters allowing for Flow Director
IPv6 and VLAN filters.

Kaixu Xia removes an unneeded assignment.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This entry used when skipping the parser needed,
for example, the custom header pretended to ethernet header.
Suggested-by: Liron Himi <liron@marvell.com>
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The changes to make rxrpc create the udp socket missed a bit to add the
Kconfig dependency on the udp tunnel code to do this.

Fix this by adding making AF_RXRPC select NET_UDP_TUNNEL.

Fixes: 1a9b86c9 ("rxrpc: use udp tunnel APIs instead of open code in rxrpc_open_socket")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Vadim Fedorenko <vfedorenko@novek.ru>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
cc: alaa@dev.mellanox.co.il
cc: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Hariprasad Kelam says:

====================
ethtool support for fec and link configuration

This series of patches add support for forward error correction(fec) and
physical link configuration. Patches 1&2 adds necessary mbox handlers for fec
mode configuration request and to fetch stats. Patch 3 registers driver
callbacks for fec mode configuration and display. Patch 4&5 adds support of mbox
handlers for configuring link parameters like speed/duplex and autoneg etc.
Patche 6&7 registers driver callbacks for physical link configuration.

Change-log:
v2:
	- Fixed review comments
	- Corrected indentation issues
        - Return -ENOMEM incase of mbox allocation failure
	- added validation for input fecparams bitmask values
        - added more comments

V3:
	- Removed inline functions
        - Make use of ethtool helpers APIs to display supported
          advertised modes
        - corrected indentation issues
        - code changes such that return early in case of failure
          to aid branch prediction
v4:
	- Corrected indentation issues
	- Use FEC_OFF if user requests for FEC_AUTO mode
	- Do not clear fec stats in case of user changes
	  fec mode
	- dont hide fec stats depending on interface mode
	  selection
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Register set_link_ksetting callback with driver such that
link configurations parameters like advertised mode,speed, duplex
and autoneg can be configured.

below command
ethtool -s eth0 advertise 0x1 speed 10 duplex full autoneg on
Signed-off-by: Christina Jacob <cjacob@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Register get_link_ksettings callback to get link status information
from the driver. As virtual function (vf) shares same physical link
same API is used for both the drivers and for loop back drivers
simply returns the fixed values as its does not have physical link.

ethtool eth3
Settings for eth3:
        Supported ports: [ ]
        Supported link modes:   10baseT/Half 10baseT/Full
                                100baseT/Half 100baseT/Full
                                1000baseT/Half 1000baseT/Full
                                10000baseKR/Full
                                1000baseX/Full
        Supports auto-negotiation: No
        Supported FEC modes: BaseR RS
        Advertised link modes:  Not reported
        Advertised pause frame use: No
        Advertised auto-negotiation: No
        Advertised FEC modes: None

ethtool lbk0
Settings for lbk0:
	Speed: 100000Mb/s
        Duplex: Full
Signed-off-by: Christina Jacob <cjacob@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

CGX supports setting advertised link modes on physical link.
This patch adds support to derive cgx mode from ethtool
link mode and pass it to firmware to configure the same.
Signed-off-by: Christina Jacob <cjacob@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

CGX LMAC, the physical interface support link configuration parameters
like speed, auto negotiation, duplex  etc. Firmware saves these into
memory region shared between firmware and this driver.

This patch adds mailbox handler set_link_mode, fw_data_get to
configure and read these parameters.
Signed-off-by: Christina Jacob <cjacob@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add ethtool support to configure fec modes baser/rs and
support to fecth FEC stats from CGX as well PHY.

Configure fec mode
	- ethtool --set-fec eth0 encoding rs/baser/off/auto
Query fec mode
	- ethtool --show-fec eth0
Signed-off-by: Christina Jacob <cjacob@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds support to fetch fec stats from PHY. The stats are
put in the shared data struct fwdata.  A PHY driver indicates
that it has FEC stats by setting the flag fwdata.phy.misc.has_fec_stats

Besides CGX_CMD_GET_PHY_FEC_STATS, also add CGX_CMD_PRBS and
CGX_CMD_DISPLAY_EYE to enum cgx_cmd_id so that Linux's enum list is in sync
with firmware's enum list.
Signed-off-by: Felix Manlunas <fmanlunas@marvell.com>
Signed-off-by: Christina Jacob <cjacob@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

CGX block supports forward error correction modes baseR
and RS. This patch adds support to set encoding mode
and to read corrected/uncorrected block counters

Adds new mailbox handlers set_fec to configure encoding modes
and fec_stats to read counters and also increase mbox timeout
to accomdate firmware command response timeout.

Along with new CGX_CMD_SET_FEC command add other commands to
sync with kernel enum list with firmware.
Signed-off-by: Christina Jacob <cjacob@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pavel pointed that the return of dma_addr_t in
otx2_alloc_rbuf/__otx2_alloc_rbuf() seem suspicious because a negative
error code may be returned in some cases. For a dma_addr_t, the error
code such as -ENOMEM does seem a valid value, so we can't judge if the
buffer allocation fail or not based on that value. Add a parameter for
otx2_alloc_rbuf/__otx2_alloc_rbuf() to store the dma address and make
the return value to indicate if the buffer allocation really fail or
not.
Reported-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Tested-by: Subbaraya Sundeep <sbhatta@marvell.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: David S. Miller <davem@davemloft.net>

MBIM has initially been specified by USB-IF for transporting data (IP)
between a modem and a host over USB. However some modern modems also
support MBIM over PCIe (via MHI). In the same way as QMAP(rmnet), it
allows to aggregate IP packets and to perform context multiplexing.

This change adds minimal MBIM data transport support to MHI, allowing
to support MBIM only modems. MBIM being based on USB NCM, it reuses
and copy some helpers/functions from the USB stack (cdc-ncm, cdc-mbim).

Note that is a subset of the CDC-MBIM specification, supporting only
transport of network data (IP), there is no support for DSS. Moreover
the multi-session (for multi-pdn) is not supported in this initial
version, but will be added latter, and aligned with the cdc-mbim
solution (VLAN tags).

This code has been inspired from the mhi_mbim downstream implementation
(Carl Yin <carl.yin@quectel.com>).
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This can be used by proto when packet len is incorrect.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>