- 27 Dec, 2021 10 commits
-
-
Kai-Heng Feng authored
pci_pm_suspend_noirq() and pci_pm_resume_noirq() already handle power transition for system-wide suspend and resume, so it's not necessary to do it in the driver. Signed-off-by:
Kai-Heng Feng <kai.heng.feng@canonical.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Horatiu Vultur authored
The blamed commit changed the vlan used by the host ports to be 4095 instead of 0. Because of this change the following issues are seen: - when the port is probed first it was adding an entry in the MAC table with the wrong vlan (port->pvid which is default 0) and not HOST_PVID - when the port is removed from a bridge, it was using the wrong vlan to add entries in the MAC table. It was using the old PVID and not the HOST_PVID This patch fixes this two issues by using the HOST_PVID instead of port->pvid. Fixes: 6d2c186a ("net: lan966x: Add vlan support.") Signed-off-by:
Horatiu Vultur <horatiu.vultur@microchip.com> Signed-off-by:
-
David S. Miller authored
Michael Chan says: ==================== bnxt_en: Update for net-next This series includes some added error logging for firmware error reports, DIM interrupt sampling for the latest 5750X chips, CQE interrupt coalescing mode support, and to use RX page frag buffers for better software GRO performance. ==================== Signed-off-by: -
Jakub Kicinski authored
If NETIF_F_GRO_HW is disabled, the existing driver code uses kmalloc'ed data for RX buffers. This causes inefficient SW GRO performance because the GRO data is merged using the less efficient frag_list. Use netdev_alloc_frag() and friends instead so that GRO data can be merged into skb_shinfo(skb)->frags for better performance. [Use skb_free_frag() - Vikas Gupta] Signed-off-by:
Jakub Kicinski <kuba@kernel.org> Reviewed-by:
Pavan Chebbi <pavan.chebbi@broadcom.com> Reviewed-by:
Andy Gospodarek <gospo@broadcom.com> Signed-off-by:
Vikas Gupta <vikas.gupta@broadcom.com> Signed-off-by:
Michael Chan <michael.chan@broadcom.com> Signed-off-by:
-
Edwin Peer authored
The xdp_do_flush_map function has been replaced with the more general xdp_do_flush(). Signed-off-by:
Edwin Peer <edwin.peer@broadcom.com> Signed-off-by:
-
Michael Chan authored
Support showing and setting the CQE mode in ethtool. Reviewed-by:
-
Michael Chan authored
CQE coalescing mode is the same as the timer reset coalescing mode on Broadcom devices. Currently this mode is always enabled if it is supported by the device. Restructure the code slightly to support dynamically changing this mode. Add a flags field to struct bnxt_coal. Initially, the CQE flag will be set for the RX and TX side if the device supports it. We need to move bnxt_init_dflt_coal() to set up default coalescing until the capability is determined. Reviewed-by:
-
Andy Gospodarek authored
5750X (P5) chips handle receiving packets on the NQ rather than the main completion queue so we need to get and set stats from the correct spots for dynamic interrupt moderation. Signed-off-by:
-
Michael Chan authored
Log the unrecognized error report type value as well. Reviewed-by:
-
Somnath Kotur authored
FW has been modified to send a new async event when it detects a pause storm. Register for this new event and log it upon receipt. Reviewed-by:
Somnath Kotur <somnath.kotur@broadcom.com> Signed-off-by:
-
- 24 Dec, 2021 4 commits
-
-
Christophe JAILLET authored
Use 'bitmap_zalloc()' to simplify code, improve the semantic and reduce some open-coded arithmetic in allocator arguments. Also change the corresponding 'kfree()' into 'bitmap_free()' to keep consistency. Signed-off-by:
Christophe JAILLET <christophe.jaillet@wanadoo.fr> Link: https://lore.kernel.org/r/f9541b085ec68e573004e1be200c11c9c901181a.1640295165.git.christophe.jaillet@wanadoo.frSigned-off-by:
-
Horatiu Vultur authored
Add config_init for LAN8814. This function is required for the following reasons: - we need to make sure that the PHY is reset, - disable ANEG with QSGMII PCS Host side - swap the MDI-X A,B transmit so that there will not be any link flip-flaps when the PHY gets a link. Signed-off-by:
-
Randy Dunlap authored
Use the possessive "its" instead of the contraction of "it is" ("it's") in user messages. Signed-off-by:Randy Dunlap <rdunlap@infradead.org> Cc: Krzysztof Halasa <khc@pm.waw.pl> Cc: "David S. Miller" <davem@davemloft.net> Cc: Jakub Kicinski <kuba@kernel.org> Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netJakub Kicinski authored
include/net/sock.h commit 8f905c0e ("inet: fully convert sk->sk_rx_dst to RCU rules") commit 43f51df4 ("net: move early demux fields close to sk_refcnt") https://lore.kernel.org/all/20211222141641.0caa0ab3@canb.auug.org.au/Signed-off-by:
-
- 23 Dec, 2021 26 commits
-
-
Nobuhiro Iwamatsu authored
ETHER_CLK_SEL_FREQ_SEL_2P5M is not 0 bit of the register. This is a value, which is 0. Fix from BIT(0) to 0. Reported-by:
Yuji Ishikawa <yuji2.ishikawa@toshiba.co.jp> Fixes: b38dd98f ("net: stmmac: Add Toshiba Visconti SoCs glue driver") Signed-off-by:
Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp> Link: https://lore.kernel.org/r/20211223073633.101306-1-nobuhiro1.iwamatsu@toshiba.co.jpSigned-off-by:
-
Jakub Kicinski authored
Hayes Wang says: ==================== r8152: fix bugs Patch #1 fix the issue of force speed mode for RTL8156. Patch #2 fix the issue of unexpected ocp_base. ==================== Link: https://lore.kernel.org/r/20211223092702.23841-386-nic_swsd@realtek.comSigned-off-by:
-
Hayes Wang authored
There are some chances that the actual base of hardware is different from the value recorded by driver, so we have to reset the variable of ocp_base to sync it. Set ocp_base to -1. Then, it would be updated and the new base would be set to the hardware next time. Signed-off-by:
Hayes Wang <hayeswang@realtek.com> Signed-off-by:
-
Hayes Wang authored
It needs to set mdio force mode. Otherwise, link off always occurs when setting force speed. Fixes: 195aae32 ("r8152: support new chips") Signed-off-by:
-
Remi Pommarel authored
Commit 561d8352 ("bridge: use ndo_siocdevprivate") changed the source and destination arguments of copy_{to,from}_user in bridge's old_deviceless() from args[1] to uarg breaking SIOC{G,S}IFBR ioctls. Commit cbd7ad29 ("net: bridge: fix ioctl old_deviceless bridge argument") fixed only BRCTL_{ADD,DEL}_BRIDGES commands leaving BRCTL_GET_BRIDGES one untouched. The fixes BRCTL_GET_BRIDGES as well and has been tested with busybox's brctl. Example of broken brctl: $ brctl show bridge name bridge id STP enabled interfaces brctl: can't get bridge name for index 0: No such device or address Example of fixed brctl: $ brctl show bridge name bridge id STP enabled interfaces br0 8000.000000000000 no Fixes: 561d8352 ("bridge: use ndo_siocdevprivate") Signed-off-by:
Remi Pommarel <repk@triplefau.lt> Reviewed-by:
Arnd Bergmann <arnd@arndb.de> Acked-by:
Nikolay Aleksandrov <nikolay@nvidia.com> Link: https://lore.kernel.org/all/20211223153139.7661-2-repk@triplefau.lt/Signed-off-by:
-
Xiaoliang Yang authored
Convert the u32 variable to type u64 in a context where expression of type u64 is required to avoid potential overflow. Fixes: e9e37200 ("net: stmmac: ptp: update tas basetime after ptp adjust") Signed-off-by:
Xiaoliang Yang <xiaoliang.yang_1@nxp.com> Link: https://lore.kernel.org/r/20211223073928.37371-1-xiaoliang.yang_1@nxp.comSigned-off-by:
-
Xiaoliang Yang authored
For Ocelot switches, the CPU injected frames have an injection header where it can specify the QoS class of the packet and the DSA tag, now it uses the SKB priority to set that. If a traffic class to priority mapping is configured on the netdevice (with mqprio for example ...), it won't be considered for CPU injected headers. This patch make the QoS class aligned to the priority to traffic class mapping if it exists. Fixes: 8dce89aa ("net: dsa: ocelot: add tagger for Ocelot/Felix switches") Signed-off-by:
Marouen Ghodhbane <marouen.ghodhbane@nxp.com> Link: https://lore.kernel.org/r/20211223072211.33130-1-xiaoliang.yang_1@nxp.comSigned-off-by:
-
Paolo Abeni authored
After commit d3256efd ("veth: allow enabling NAPI even without XDP"), if GRO is enabled on a veth device and TSO is disabled on the peer device, TCP skbs will go through the NAPI callback. If there is no XDP program attached, the veth code does not perform any share check, and shared/cloned skbs could enter the GRO engine. Ignat reported a BUG triggered later-on due to the above condition: [ 53.970529][ C1] kernel BUG at net/core/skbuff.c:3574! [ 53.981755][ C1] invalid opcode: 0000 [#1] PREEMPT SMP KASAN PTI [ 53.982634][ C1] CPU: 1 PID: 19 Comm: ksoftirqd/1 Not tainted 5.16.0-rc5+ #25 [ 53.982634][ C1] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 0.0.0 02/06/2015 [ 53.982634][ C1] RIP: 0010:skb_shift+0x13ef/0x23b0 [ 53.982634][ C1] Code: ea 03 0f b6 04 02 48 89 fa 83 e2 07 38 d0 7f 08 84 c0 0f 85 41 0c 00 00 41 80 7f 02 00 4d 8d b5 d0 00 00 00 0f 85 74 f5 ff ff <0f> 0b 4d 8d 77 20 be 04 00 00 00 4c 89 44 24 78 4c 89 f7 4c 89 8c [ 53.982634][ C1] RSP: 0018:ffff8881008f7008 EFLAGS: 00010246 [ 53.982634][ C1] RAX: 0000000000000000 RBX: ffff8881180b4c80 RCX: 0000000000000000 [ 53.982634][ C1] RDX: 0000000000000002 RSI: ffff8881180b4d3c RDI: ffff88810bc9cac2 [ 53.982634][ C1] RBP: ffff8881008f70b8 R08: ffff8881180b4cf4 R09: ffff8881180b4cf0 [ 53.982634][ C1] R10: ffffed1022999e5c R11: 0000000000000002 R12: 0000000000000590 [ 53.982634][ C1] R13: ffff88810f940c80 R14: ffff88810f940d50 R15: ffff88810bc9cac0 [ 53.982634][ C1] FS: 0000000000000000(0000) GS:ffff888235880000(0000) knlGS:0000000000000000 [ 53.982634][ C1] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 53.982634][ C1] CR2: 00007ff5f9b86680 CR3: 0000000108ce8004 CR4: 0000000000170ee0 [ 53.982634][ C1] Call Trace: [ 53.982634][ C1] <TASK> [ 53.982634][ C1] tcp_sacktag_walk+0xaba/0x18e0 [ 53.982634][ C1] tcp_sacktag_write_queue+0xe7b/0x3460 [ 53.982634][ C1] tcp_ack+0x2666/0x54b0 [ 53.982634][ C1] tcp_rcv_established+0x4d9/0x20f0 [ 53.982634][ C1] tcp_v4_do_rcv+0x551/0x810 [ 53.982634][ C1] tcp_v4_rcv+0x22ed/0x2ed0 [ 53.982634][ C1] ip_protocol_deliver_rcu+0x96/0xaf0 [ 53.982634][ C1] ip_local_deliver_finish+0x1e0/0x2f0 [ 53.982634][ C1] ip_sublist_rcv_finish+0x211/0x440 [ 53.982634][ C1] ip_list_rcv_finish.constprop.0+0x424/0x660 [ 53.982634][ C1] ip_list_rcv+0x2c8/0x410 [ 53.982634][ C1] __netif_receive_skb_list_core+0x65c/0x910 [ 53.982634][ C1] netif_receive_skb_list_internal+0x5f9/0xcb0 [ 53.982634][ C1] napi_complete_done+0x188/0x6e0 [ 53.982634][ C1] gro_cell_poll+0x10c/0x1d0 [ 53.982634][ C1] __napi_poll+0xa1/0x530 [ 53.982634][ C1] net_rx_action+0x567/0x1270 [ 53.982634][ C1] __do_softirq+0x28a/0x9ba [ 53.982634][ C1] run_ksoftirqd+0x32/0x60 [ 53.982634][ C1] smpboot_thread_fn+0x559/0x8c0 [ 53.982634][ C1] kthread+0x3b9/0x490 [ 53.982634][ C1] ret_from_fork+0x22/0x30 [ 53.982634][ C1] </TASK> Address the issue by skipping the GRO stage for shared or cloned skbs. To reduce the chance of OoO, try to unclone the skbs before giving up. v1 -> v2: - use avoid skb_copy and fallback to netif_receive_skb - Eric Reported-by:
Ignat Korchagin <ignat@cloudflare.com> Fixes: d3256efd ("veth: allow enabling NAPI even without XDP") Signed-off-by:
Paolo Abeni <pabeni@redhat.com> Tested-by:
Eric Dumazet <edumazet@google.com> Link: https://lore.kernel.org/r/b5f61c5602aab01bac8d711d8d1bfab0a4817db7.1640197544.git.pabeni@redhat.comSigned-off-by:
-
Jakub Kicinski authored
Merge tag 'wireless-drivers-next-2021-12-23' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next Kalle Valo says: ==================== wireless-drivers-next patches for v5.17 Third set of patches for v5.17, and the final one if all goes well. We have Specific Absorption Rate (SAR) support for both mt76 and rtw88. Also iwlwifi should be now W=1 warning free. But otherwise nothing really special this time, business as usual. Major changes: mt76 * Specific Absorption Rate (SAR) support * mt7921: new PCI ids * mt7921: 160 MHz channel support iwlwifi * fix W=1 and sparse warnings * BNJ hardware support * add new killer device ids * support for Time-Aware-SAR (TAS) from the BIOS * Optimized Connectivity Experience (OCE) scan support rtw88 * hardware scan * Specific Absorption Rate (SAR) support ath11k * qca6390/wcn6855: report signal and tx bitrate * qca6390: rfkill support * qca6390/wcn6855: regdb.bin support ath5k * switch to rate table based lookup wilc1000 * spi: reset/enable GPIO support * tag 'wireless-drivers-next-2021-12-23' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next: (148 commits) mt76: mt7921: fix a possible race enabling/disabling runtime-pm wilc1000: Document enable-gpios and reset-gpios properties wilc1000: Add reset/enable GPIO support to SPI driver wilc1000: Convert static "chipid" variable to device-local variable rtw89: 8852a: correct bit definition of dfs_en rtw88: don't consider deep PS mode when transmitting packet ath11k: Fix unexpected return buffer manager error for QCA6390 ath11k: add support of firmware logging for WCN6855 ath11k: Fix napi related hang ath10k: replace strlcpy with strscpy rtw88: support SAR via kernel common API rtw88: 8822c: add ieee80211_ops::hw_scan iwlwifi: mei: wait before mapping the shared area iwlwifi: mei: clear the ownership when the driver goes down iwlwifi: yoyo: fix issue with new DBGI_SRAM region read. iwlwifi: fw: fix some scan kernel-doc iwlwifi: pcie: make sure prph_info is set when treating wakeup IRQ iwlwifi: mvm: remove card state notification code iwlwifi: mvm: drop too short packets silently iwlwifi: mvm: fix AUX ROC removal ... ==================== Link: https://lore.kernel.org/r/20211223141108.78808C36AE9@smtp.kernel.orgSigned-off-by:
-
David S. Miller authored
Amit Cohen says: ==================== mlxsw: Add tests for VxLAN with IPv6 underlay mlxsw driver lately added support for VxLAN with IPv6 underlay. This set adds tests for IPv6, which are dedicated for mlxsw. Patch set overview: Patches #1-#2 make vxlan.sh test more flexible and extend it for IPv6 Patches #3-#4 make vxlan_fdb_veto.sh test more flexible and extend it for IPv6 Patches #5-#6 add tests for VxLAN flooding for different ASICs Patches #7-#8 add test for VxLAN related traps and align the existing test ==================== Signed-off-by: -
Amit Cohen authored
Change the case that sends packets with "too short inner packet" to include part of ethernet header, to make the trap to be triggered due to the correct reason. According to ASIC arch, the trap is triggered if overlay packet length is less than 18B, and the minimum inner packet should include source MAC and destination MAC. Till now the case passed because one of the reserved bits in VxLAN header was used. This issue was found while adding an equivalent test for IPv6. Signed-off-by:
Amit Cohen <amcohen@nvidia.com> Reviewed-by:
Petr Machata <petrm@nvidia.com> Signed-off-by:
-
Amit Cohen authored
The test configures VxLAN with IPv6 underlay and verifies that the expected traps are triggered under the right conditions. The test is similar to the existing IPv4 test. Signed-off-by:
-
Amit Cohen authored
The device stores flood records in a singly linked list where each record stores up to X IP addresses of remote VTEPs. The number of records is changed according to ASIC type and address family. Add a test which is similar to the existing IPv4 test to check IPv6. The test is dedicated for Spectrum-2 and above, which support up to four IPv6 addresses in one record. The test verifies that packets are correctly flooded in various cases such as deletion of a record in the middle of the list. Signed-off-by:
-
Amit Cohen authored
The device stores flood records in a singly linked list where each record stores up to X IP addresses of remote VTEPs. The number of records is changed according to ASIC type and address family. Add a test which is similar to the existing IPv4 test to check IPv6. The test is dedicated for Spectrum-1 switches, which support up to five IPv6 addresses in one record. The test verifies that packets are correctly flooded in various cases such as deletion of a record in the middle of the list. Signed-off-by:
-
Amit Cohen authored
Add test to verify FDB vetos of VxLAN with IPv6 underlay. Use the existing test which checks IPv4. Signed-off-by:
-
Amit Cohen authored
vxlan_fdb_veto.sh cases are dedicated to test VxLAN with IPv4 underlay. The main changes to test IPv6 underlay are IP addresses and some flags. Add variables to define all the values which supposed to be different for IPv6 testing, set them to use the existing values by default. The next patch will define the new added variables in a separated file, so the same tests can be used for IPv6 also. Signed-off-by:
-
Amit Cohen authored
Add test to verify configuration of VxLAN with IPv6 underlay. Use the existing test which checks IPv4. Add separated test cases for learning which is not supported for IPv6 and for UDP checksum flags which are different from IPv4 flags. Signed-off-by:
-
Amit Cohen authored
vxlan.sh cases are dedicated to test VxLAN with IPv4 underlay. The main changes to test IPv6 underlay are IP addresses and some flags. Add variables to define all the values which supposed to be different for IPv6 testing, set them to use the existing values by default. The next patch will define the new added variables in a separated file, so the same tests can be used for IPv6 also. Rename some functions to include "ipv4", so the next patch will add equivalent functions for IPv6. Signed-off-by:
-
Andy Shevchenko authored
When kernel.h is used in the headers it adds a lot into dependency hell, especially when there are circular dependencies are involved. Replace kernel.h inclusion with the list of what is really being used. Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by:
Sergey Ryazanov <ryazanov.s.a@gmail.com> Signed-off-by:
-
Ong Boon Leong authored
This patch adds basic support for EtherType RX frame steering for LLDP and PTP using the hardware offload capabilities. Example steps for setting up RX frame steering for LLDP and PTP: $ IFDEVNAME=eth0 $ tc qdisc add dev $IFDEVNAME ingress $ tc qdisc add dev $IFDEVNAME root mqprio num_tc 8 \ map 0 1 2 3 4 5 6 7 0 0 0 0 0 0 0 0 \ queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 hw 0 For LLDP $ tc filter add dev $IFDEVNAME parent ffff: protocol 0x88cc \ flower hw_tc 5 OR $ tc filter add dev $IFDEVNAME parent ffff: protocol LLDP \ flower hw_tc 5 For PTP $ tc filter add dev $IFDEVNAME parent ffff: protocol 0x88f7 \ flower hw_tc 6 Show tc ingress filter $ tc filter show dev $IFDEVNAME ingress v1->v2: Thanks to Kurt's and Sebastian's suggestion. - change from __be16 to u16 etype - change ETHER_TYPE_FULL_MASK to use cpu_to_be16() macro Signed-off-by:Ong Boon Leong <boon.leong.ong@intel.com> Signed-off-by:
-
Horatiu Vultur authored
This patch series extends the current supported bridge flags with the following flags: BR_FLOOD, BR_BCAST_FLOOD and BR_LEARNING. Signed-off-by:
-
Baowen Zheng authored
Fix suspicious rcu_dereference_protected() usage when offloading tc action. We should hold tcfa_lock to offload tc action in action initiation. Without these changes, the following warning will be observed: WARNING: suspicious RCU usage 5.16.0-rc5-net-next-01504-g7d1f236dcffa-dirty #50 Tainted: G I ----------------------------- include/net/tc_act/tc_tunnel_key.h:33 suspicious rcu_dereference_protected() usage! 1 lock held by tc/12108: CPU: 4 PID: 12108 Comm: tc Tainted: G Hardware name: Dell Inc. PowerEdge R740/07WCGN, BIOS 1.6.11 11/20/2018 Call Trace: <TASK> dump_stack_lvl+0x49/0x5e dump_stack+0x10/0x12 lockdep_rcu_suspicious+0xed/0xf8 tcf_tunnel_key_offload_act_setup+0x1de/0x300 [act_tunnel_key] tcf_action_offload_add_ex+0xc0/0x1f0 tcf_action_init+0x26a/0x2f0 tcf_action_add+0xa9/0x1f0 tc_ctl_action+0xfb/0x170 rtnetlink_rcv_msg+0x169/0x510 ? sched_clock+0x9/0x10 ? rtnl_newlink+0x70/0x70 netlink_rcv_skb+0x55/0x100 rtnetlink_rcv+0x15/0x20 netlink_unicast+0x1a8/0x270 netlink_sendmsg+0x245/0x490 sock_sendmsg+0x65/0x70 ____sys_sendmsg+0x219/0x260 ? __import_iovec+0x2c/0x150 ___sys_sendmsg+0xb7/0x100 ? __lock_acquire+0x3d5/0x1f40 ? __this_cpu_preempt_check+0x13/0x20 ? lock_is_held_type+0xe4/0x140 ? sched_clock+0x9/0x10 ? ktime_get_coarse_real_ts64+0xbe/0xd0 ? __this_cpu_preempt_check+0x13/0x20 ? lockdep_hardirqs_on+0x7e/0x100 ? ktime_get_coarse_real_ts64+0xbe/0xd0 ? trace_hardirqs_on+0x2a/0xf0 __sys_sendmsg+0x5a/0xa0 ? syscall_trace_enter.constprop.0+0x1dd/0x220 __x64_sys_sendmsg+0x1f/0x30 do_syscall_64+0x3b/0x90 entry_SYSCALL_64_after_hwframe+0x44/0xae RIP: 0033:0x7f4db7bb7a60 Fixes: 8cbfe939 ("flow_offload: allow user to offload tc action to net device") Reported-by:
Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by:
Baowen Zheng <baowen.zheng@corigine.com> Signed-off-by:
Louis Peens <louis.peens@corigine.com> Signed-off-by:
-
Xin Long authored
Struct sctp_ep_common is included in both asoc and ep, but hlist_node and hashent are only needed by ep after asoc_hashtable was dropped by Commit b5eff712 ("sctp: drop the old assoc hashtable of sctp"). So it is better to move hlist_node and hashent from sctp_ep_common to sctp_endpoint, and it saves some space for each asoc. Signed-off-by:
Xin Long <lucien.xin@gmail.com> Signed-off-by:
-
Jakub Kicinski authored
Amit Cohen says: ==================== Add tests for VxLAN with IPv6 underlay mlxsw driver lately added support for VxLAN with IPv6 underlay. This set adds the relevant tests for IPv6, most of them are same to IPv4 tests with the required changes. Patch set overview: Patch #1 relaxes requirements for offloading TC filters that match on 802.1q fields. The following selftests make use of these newly-relaxed filters. Patch #2 adds preparation as part of selftests API, which will be used later. Patches #3-#4 add tests for VxLAN with bridge aware and unaware. Patche #5 cleans unused function. Patches #6-#7 add tests for VxLAN symmetric and asymmetric. Patch #8 adds test for Q-in-VNI. ==================== Link: https://lore.kernel.org/r/20211221144949.2527545-1-amcohen@nvidia.comSigned-off-by:
-
Amit Cohen authored
Add test to check Q-in-VNI traffic with IPv6 underlay and overlay. The test is similar to the existing IPv4 test. Signed-off-by:
-
Amit Cohen authored
In a similar fashion to the asymmetric test, add a test for symmetric routing. In symmetric routing both the ingress and egress VTEPs perform routing in the overlay network into / from the VxLAN tunnel. Packets in different directions use the same VNI - the L3 VNI. Different tenants (VRFs) use different L3 VNIs. Add a test which is similar to the existing IPv4 test to check IPv6. Signed-off-by:
-
