When the looked-up LTK is one generated by Secure Connections pairing
the security level it gives is BT_SECURITY_FIPS. This patch updates the
LTK request event handler to correctly set this level.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

We need a dedicated LTK type for LTK resulting from a Secure Connections
based SMP pairing. This patch adds a new define for it and ensures that
both the New LTK event as well as the Load LTKs command supports it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch updates the functions which map the SMP authentication
request to a security level and vice-versa to take into account the
Secure Connections feature.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch adds a new SMP flag for tracking whether Secure Connections
is in use and sets the flag when both remote and local side have elected
to use Secure Connections.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

If we haven't enabled SC support on our side we should use the same mask
for the authentication requirement as we were using before SC support
was added, otherwise we should use the extended mask for SC.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch adds basic SMP defines for commands, error codes and PDU
definitions for the LE Secure Connections feature.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

When we get a Link Key Notification HCI event we should already have a
hci_conn object. This should have been created either in the Connection
Request event handler, the hci_connect_acl() function or the
hci_cs_create_conn() function (if the request was not sent by the
kernel).

Since the only case that we'd end up not having a hci_conn in the Link
Key Notification event handler would be essentially broken hardware it's
safe to simply bail out from the function if this happens.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

To pave the way for future fixed channels to be added easily we should
track both the local and remote mask on a per-L2CAP connection (struct
l2cap_conn) basis. So far the code has used a global variable in a racy
way which anyway needs fixing.

This patch renames the existing conn->fixed_chan_mask that tracked
the remote mask to conn->remote_fixed_chan and adds a new variable
conn->local_fixed_chan to track the local mask. Since the HS support
info is now available in the local mask we can remove the
conn->hs_enabled variable.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The Bluetooth spec states that automatically flushable packets may not
be sent over a LE-U link.
Signed-off-by: Steven Walter <stevenrwalter@gmail.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>

Add support for Bluetooth MCI WB335 (AR9565) Wi-Fi+bt module. This
Bluetooth module requires loading patch and sysconfig by ath3k driver.

T:  Bus=01 Lev=02 Prnt=03 Port=00 Cnt=01 Dev#= 20 Spd=12   MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=13d3 ProdID=3408 Rev= 0.02
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
A:  FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Cc: stable@vger.kernel.org

Removes unnecessary if statement check for net device. Error check performed
after alloc_netdev().

	ndev = alloc_netdev(sizeof(*sdata) + local->hw.vif_data_size, name,
			    NET_NAME_UNKNOWN, ieee802154_if_setup);
        if (!ndev)
                return ERR_PTR(-ENOMEM);
	..
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Acked-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Signed-off-by: Varka Bhadram <varkab@cdac.in>
Acked-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Host sleep status flag should be reset when there is an
interrupt from device.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This can be used to have GPIO host wakeup method suitable for the
platform and configurable GAP for host sleep handshake.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Calibration data can be downloaded through device tree method. This
patch adds the documentation. Also, instead of searching device tree
node by name using of_find_node_by_name() API, let's use
for_each_compatible_node().
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch converts the hdev->link_keys list to be protected through
RCU, thereby eliminating the need to hold the hdev lock while accessing
the list.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

When a connection is requested the conn->pending_sec_level value gets
set to whatever level the user requested the connection to be. During
the pairing process there are various sanity checks to try to ensure
that the right length PIN or right IO Capability is used to satisfy the
target security level. However, when we finally get hold of the link key
that is to be used we should still set the actual final security level
from the key type.

This way when we eventually get an Encrypt Change event the correct
value gets copied to conn->sec_level.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

In __hci_cmd_sync_ev() and __hci_req_sync() if the hci_req_run() call
fails and we return from the functions we should ensure that the state
doesn't remain in TASK_INTERRUPTIBLE that we just set it to. This patch
fixes missing calls to set_current_state(TASK_RUNNING) in both places.
Reported-by: Kirill A. Shutemov <kirill@shutemov.name>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Tested-by: Kirill A. Shutemov <kirill@shutemov.name>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This variant requires the flag BTUSB_BCM_PATCHRAM to work.

Relevant details from /sys/kernel/debug/usb/devices:

T:  Bus=01 Lev=02 Prnt=02 Port=04 Cnt=01 Dev#=  3 Spd=12   MxCh= 0
D:  Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=13d3 ProdID=3404 Rev= 1.12
S:  Manufacturer=Broadcom Corp
S:  Product=BCM20702A0
S:  SerialNumber=240A646F1XXX
C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=  0mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=84(I) Atr=02(Bulk) MxPS=  32 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS=  32 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)

The firmware was extracted from a Windows 8.1 64-bit installation
and converted from 'hex' to 'hcd' for use in Linux.

Under Windows it also identifies itself as BCM20702A0,
but the firmware is named "BCM20702A1_001.002.014.1315.1356.hex"
and is located in "%SYSTEMROOT%\system32\drivers\"
(md5 67cf6bfdae61c4bb819a66da984f7913)
(sha1 5f74cc6a9a3bf19ee0f8c3d01e4be34c609b188f)

The same firmware file is also available as a download at
http://www.asrock.com/mb/Intel/Z87E-ITX/?cat=Download&os=All
marked as "Bluetooth driver ver:12.0.0.7820"

'hcd' file should be placed at "brcm/BCM20702A0-13d3-3404.hcd"
inside the firmware directory (e.g. "/lib/firmware")
Signed-off-by: Fabio K <healthkit@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Doing things like hci_conn_hash_flush() while holding the hdev lock is
risky since its synchronous pending work cancellation could cause the
L2CAP layer to try to reacquire the hdev lock. Right now there doesn't
seem to be any obvious places where this would for certain happen but
it's already enough to cause lockdep to start warning against the hdev
and the work struct locks being taken in the "wrong" order:

[  +0.000373] mgmt-tester/1603 is trying to acquire lock:
[  +0.000292]  ((&conn->pending_rx_work)){+.+.+.}, at: [<c104266d>] flush_work+0x0/0x181
[  +0.000270]
but task is already holding lock:
[  +0.000000]  (&hdev->lock){+.+.+.}, at: [<c13b9a80>] hci_dev_do_close+0x166/0x359
[  +0.000000]
which lock already depends on the new lock.

[  +0.000000]
the existing dependency chain (in reverse order) is:
[  +0.000000]
-> #1 (&hdev->lock){+.+.+.}:
[  +0.000000]        [<c105ea8f>] lock_acquire+0xe3/0x156
[  +0.000000]        [<c140c663>] mutex_lock_nested+0x54/0x375
[  +0.000000]        [<c13d644b>] l2cap_recv_frame+0x293/0x1a9c
[  +0.000000]        [<c13d7ca4>] process_pending_rx+0x50/0x5e
[  +0.000000]        [<c1041a3f>] process_one_work+0x21c/0x436
[  +0.000000]        [<c1041e3d>] worker_thread+0x1be/0x251
[  +0.000000]        [<c1045a22>] kthread+0x94/0x99
[  +0.000000]        [<c140f801>] ret_from_kernel_thread+0x21/0x30
[  +0.000000]
-> #0 ((&conn->pending_rx_work)){+.+.+.}:
[  +0.000000]        [<c105e158>] __lock_acquire+0xa07/0xc89
[  +0.000000]        [<c105ea8f>] lock_acquire+0xe3/0x156
[  +0.000000]        [<c1042696>] flush_work+0x29/0x181
[  +0.000000]        [<c1042864>] __cancel_work_timer+0x76/0x8f
[  +0.000000]        [<c104288c>] cancel_work_sync+0xf/0x11
[  +0.000000]        [<c13d4c18>] l2cap_conn_del+0x72/0x183
[  +0.000000]        [<c13d8953>] l2cap_disconn_cfm+0x49/0x55
[  +0.000000]        [<c13be37a>] hci_conn_hash_flush+0x7a/0xc3
[  +0.000000]        [<c13b9af6>] hci_dev_do_close+0x1dc/0x359
[  +0.012038]        [<c13bbe38>] hci_unregister_dev+0x6e/0x1a3
[  +0.000000]        [<c12d33c1>] vhci_release+0x28/0x47
[  +0.000000]        [<c10dd6a9>] __fput+0xd6/0x154
[  +0.000000]        [<c10dd757>] ____fput+0xd/0xf
[  +0.000000]        [<c1044bb2>] task_work_run+0x6b/0x8d
[  +0.000000]        [<c1001bd2>] do_notify_resume+0x3c/0x3f
[  +0.000000]        [<c140fa70>] work_notifysig+0x29/0x31
[  +0.000000]
other info that might help us debug this:

[  +0.000000]  Possible unsafe locking scenario:

[  +0.000000]        CPU0                    CPU1
[  +0.000000]        ----                    ----
[  +0.000000]   lock(&hdev->lock);
[  +0.000000]                                lock((&conn->pending_rx_work));
[  +0.000000]                                lock(&hdev->lock);
[  +0.000000]   lock((&conn->pending_rx_work));
[  +0.000000]
 *** DEADLOCK ***

Fully fixing this would require some quite heavy refactoring to change
how the hdev lock and hci_conn instances are handled together. A simpler
solution for now which this patch takes is to try ensure that the hdev
workqueue is empty before proceeding with the various cleanup calls,
including hci_conn_hash_flush().
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The common short form of "randomizer" is "rand" in many places
(including the Bluetooth specification). The shorter version also makes
for easier to read code with less forced line breaks. This patch renames
all occurences of "randomizer" to "rand" in the Bluetooth subsystem
code.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

For now the mgmt commands dealing with remote OOB data are strictly
BR/EDR-only. This patch fixes missing checks for the passed address type
so that any non-BR/EDR value triggers the appropriate error response.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch changes the byteorder handling for short and panid handling.
We now except to get little endian in nl802154 for these attributes.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch moves the 802.15.4 constraints WPAN_NUM_ defines into
"net/ieee802154.h" which should contain all necessary 802.15.4 related
information. Also rename these defines to a common name which is
IEEE802154_MAX_CHANNEL and IEEE802154_MAX_PAGE.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch adds support for deleting a wpan interface via nl802154.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch adds support for setting an extended address while
registration a new interface. If ieee802154_is_valid_extended_addr
getting as parameter and invalid extended address then the perm address
is fallback. This is useful to make some default handling while for
example default registration of a wpan interface while phy registration.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch adds a new nl802154 command for adding a new interface
according to a wpan phy via nl802154.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This parameter was grabbed from wireless implementation with the
identically wireless dev struct. We don't need this right now and so we
remove it. Maybe we will add it later again if we found any real reason
to have such parameter.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch replace the depracted IEEE802154_DEV to the new introduced
NL802154_IFTYPE_NODE types. There is a backwards compatibility to have
the identical types for both enum definitions. Also remove some inlcude
issue with "linux/nl802154.h", because the export nl_policy inside this
header it was always necessary to have an include of "net/rtnetlink.h"
before. The reason for this is more complicated. Nevertheless we removed
this now, because "linux/nl802154.h" is the depracted netlink interface.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

We don't and we can't name it zigbee anymore. This patch removes
deprecated information for project website.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patches removes the const keyword in variables which are non
pointers. There is no sense to declare call by value parameters as
const.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patches removes the const keyword in variables which are non
pointers. There is no sense to declare call by value parameters as
const.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patches removes the const keyword in variables which are non
pointers. There is no sense to declare call by value parameters as const.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch fix an copy&paste issue in the comment of setting symbol
duration. These comments are more correct according the at86rf212 datasheet
now.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch removes some prototypes which are not used anymore.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

When passed BDADDR_ANY the Remove Remote OOB Data comand is specified to
clear all entries. This patch adds the necessary check and calls
hci_remote_oob_data_clear() when necessary.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch adds some extra debug logs to L2CAP related code. These are
mainly to help track locking issues but will probably be useful for
debugging other types of issues as well.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Now that the SMP related key lists are converted to RCU there is nothing
in smp_cmd_sign_info() or smp_cmd_ident_addr_info() that would require
taking the hdev lock (including the smp_distribute_keys call). This
patch removes this unnecessary locking.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch set converts the hdev->identity_resolving_keys list to use
RCU to eliminate the need to use hci_dev_lock/unlock.

An additional change that must be done is to remove use of
CRYPTO_ALG_ASYNC for the hdev-specific AES crypto context. The reason is
that this context is used for matching RPAs and the loop that does the
matching is under the RCU read lock, i.e. is an atomic section which
cannot sleep.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

This patch set converts the hdev->long_term_keys list to use RCU to
eliminate the need to use hci_dev_lock/unlock.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>