- 10 Aug, 2016 33 commits
-
-
Alexander Shiyan authored
commit ba562d5e upstream. Some PINs do not have a MUX register, it is not an error. It is necessary to allow the continuation of the PINs configuration, otherwise the whole PIN-group will be configured incorrectly. Signed-off-by:
Alexander Shiyan <shc_work@mail.ru> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Tony Lindgren authored
commit 0ac3c0a4 upstream. With many repeated suspend resume cycles, the pin specific wakeirq may not always work on omaps. This is because the write to enable the pin interrupt may not have reached the device over the interconnect before suspend happens. Let's fix the issue with a flush of posted write with a readback. Reported-by:
Nishanth Menon <nm@ti.com> Signed-off-by:
Tony Lindgren <tony@atomide.com> Signed-off-by:
-
Minfei Huang authored
commit 749d088b upstream. Protocol for the "version" fields is: hypervisor raises it (making it uneven) before it starts updating the fields and raises it again (making it even) when it is done. Thus the guest can make sure the time values it got are consistent by checking the version before and after reading them. Add CPU barries after getting version value just like what function vread_pvclock does, because all of callees in this function is inline. Fixes: 502dfeffSigned-off-by:
Minfei Huang <mnghuan@gmail.com> Signed-off-by:
Paolo Bonzini <pbonzini@redhat.com> Signed-off-by:
-
Michael Welling authored
commit e9003c9c upstream. Passes input_id struct to the common probe function for the tsc200x drivers instead of just the bustype. This allows for the use of the product variable to set the input_dev->name variable according to the type of touchscreen used. Note that when we introduced support for TSC2004 we started calling everything TSC200X, so let's keep this quirk. Signed-off-by:
Michael Welling <mwelling@ieee.org> Acked-by:
Pavel Machek <pavel@ucw.cz> Acked-by:
Pali Rohár <pali.rohar@gmail.com> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
-
Cameron Gutman authored
commit caca925f upstream. This prevents a malicious USB device from causing an oops. Signed-off-by:
Cameron Gutman <aicommander@gmail.com> Signed-off-by:
-
Ping Cheng authored
commit 12afb344 upstream. Somehow the patch that added two-finger touch support forgot to update W8001_MAX_LENGTH from 11 to 13. Signed-off-by:
Ping Cheng <pingc@wacom.com> Reviewed-by:
Peter Hutterer <peter.hutterer@who-t.net> Signed-off-by:
-
Cameron Gutman authored
commit c7f14293 upstream. Xbox One controllers have multiple interfaces which all have the same class, subclass, and protocol. One of the these interfaces has only a single endpoint. When Xpad attempts to bind to this interface, it causes an oops when trying initialize the output URB by trying to access the second endpoint's descriptor. This situation was avoided for known Xbox One devices by checking the XTYPE constant associated with the VID and PID tuple. However, this breaks when new or previously unknown Xbox One controllers are attached to the system. This change addresses the problem by deriving the XTYPE for Xbox One controllers based on the interface protocol before checking the interface number. Fixes: 1a48ff81 ("Input: xpad - add support for Xbox One controllers") Signed-off-by:
-
Dmitry Torokhov authored
commit 226ba707 upstream. The touchpad in HP Pavilion 14-ab057ca reports it's version as 12 and according to Elan both 11 and 12 are valid IC types and should be identified as hw_version 4. Reported-by:
Patrick Lessard <Patrick.Lessard@cogeco.com> Tested-by:
-
Sinclair Yeh authored
commit 60842ef8 upstream. The VMWare EFI BIOS will expose port 0x5658 as an ACPI resource. This causes the port to be reserved by the APCI module as the system comes up, making it unavailable to be reserved again by other drivers, thus preserving this VMWare port for special use in a VMWare guest. This port is designed to be shared among multiple VMWare services, such as the VMMOUSE. Because of this, VMMOUSE should not try to reserve this port on its own. The VMWare non-EFI BIOS does not do this to preserve compatibility with existing/legacy VMs. It is known that there is small chance a VM may be configured such that these ports get reserved by other non-VMWare devices, and if this ever happens, the result is undefined. Signed-off-by:
Sinclair Yeh <syeh@vmware.com> Reviewed-by:
Thomas Hellstrom <thellstrom@vmware.com> Signed-off-by:
-
Kangjie Lu authored
commit e4ec8cc8 upstream. The stack object “r1” has a total size of 32 bytes. Its field “event” and “val” both contain 4 bytes padding. These 8 bytes padding bytes are sent to user without being initialized. Signed-off-by:
Kangjie Lu <kjlu@gatech.edu> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Kangjie Lu authored
commit 9a47e9cf upstream. The stack object “r1” has a total size of 32 bytes. Its field “event” and “val” both contain 4 bytes padding. These 8 bytes padding bytes are sent to user without being initialized. Signed-off-by:
-
Kangjie Lu authored
commit cec8f96e upstream. The stack object “tread” has a total size of 32 bytes. Its field “event” and “val” both contain 4 bytes padding. These 8 bytes padding bytes are sent to user without being initialized. Signed-off-by:
-
Jan Beulich authored
commit 7469be95 upstream. xenbus_dev_request_and_reply() needs to track whether a transaction is open. For XS_TRANSACTION_START messages it calls transaction_start() and for XS_TRANSACTION_END messages it calls transaction_end(). If sending an XS_TRANSACTION_START message fails or responds with an an error, the transaction is not open and transaction_end() must be called. If sending an XS_TRANSACTION_END message fails, the transaction is still open, but if an error response is returned the transaction is closed. Commit 027bd7e8 ("xen/xenbus: Avoid synchronous wait on XenBus stalling shutdown/restart") introduced a regression where failed XS_TRANSACTION_START messages were leaving the transaction open. This can cause problems with suspend (and migration) as all transactions must be closed before suspending. It appears that the problematic change was added accidentally, so just remove it. Signed-off-by:
Jan Beulich <jbeulich@suse.com> Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by:
David Vrabel <david.vrabel@citrix.com> Signed-off-by:
-
Jan Beulich authored
commit 0beef634 upstream. Inability to locate a user mode specified transaction ID should not lead to a kernel crash. For other than XS_TRANSACTION_START also don't issue anything to xenbus if the specified ID doesn't match that of any active transaction. Signed-off-by:
-
Andrey Grodzovsky authored
commit 02ef871e upstream. Current overlap check is evaluating to false a case where a filter field is fully contained (proper subset) of a r/w request. This change applies classical overlap check instead to include all the scenarios. More specifically, for (Hilscher GmbH CIFX 50E-DP(M/S)) device driver the logic is such that the entire confspace is read and written in 4 byte chunks. In this case as an example, CACHE_LINE_SIZE, LATENCY_TIMER and PCI_BIST are arriving together in one call to xen_pcibk_config_write() with offset == 0xc and size == 4. With the exsisting overlap check the LATENCY_TIMER field (offset == 0xd, length == 1) is fully contained in the write request and hence is excluded from write, which is incorrect. Signed-off-by:
Andrey Grodzovsky <andrey2805@gmail.com> Reviewed-by:
Boris Ostrovsky <boris.ostrovsky@oracle.com> Reviewed-by:
-
Vineet Gupta authored
commit f52e126c upstream. With recent binutils update to support dwarf CFI pseudo-ops in gas, we now get .eh_frame vs. .debug_frame. Although the call frame info is exactly the same in both, the CIE differs, which the current kernel unwinder can't cope with. This broke both the kernel unwinder as well as loadable modules (latter because of a new unhandled relo R_ARC_32_PCREL from .rela.eh_frame in the module loader) The ideal solution would be to switch unwinder to .eh_frame. For now however we can make do by just ensureing .debug_frame is generated by removing -fasynchronous-unwind-tables .eh_frame generated with -gdwarf-2 -fasynchronous-unwind-tables .debug_frame generated with -gdwarf-2 Fixes STAR 9001058196 Signed-off-by:
Vineet Gupta <vgupta@synopsys.com> Signed-off-by:
-
Alexey Brodkin authored
commit 9bd54517 upstream. If CONFIG_ARC_DW2_UNWIND is disabled every time arc_unwind_core() gets called following message gets printed in debug console: ----------------->8--------------- CONFIG_ARC_DW2_UNWIND needs to be enabled ----------------->8--------------- That message makes sense if user indeed wants to see a backtrace or get nice function call-graphs in perf but what if user disabled unwinder for the purpose? Why pollute his debug console? So instead we'll warn user about possibly missing feature once and let him decide if that was what he or she really wanted. Signed-off-by:
Alexey Brodkin <abrodkin@synopsys.com> Signed-off-by:
-
Andrey Ryabinin authored
commit 57675cb9 upstream. Lengthy output of sysrq-w may take a lot of time on slow serial console. Currently we reset NMI-watchdog on the current CPU to avoid spurious lockup messages. Sometimes this doesn't work since softlockup watchdog might trigger on another CPU which is waiting for an IPI to proceed. We reset softlockup watchdogs on all CPUs, but we do this only after listing all tasks, and this may be too late on a busy system. So, reset watchdogs CPUs earlier, in for_each_process_thread() loop. Signed-off-by:
Andrey Ryabinin <aryabinin@virtuozzo.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/1465474805-14641-1-git-send-email-aryabinin@virtuozzo.comSigned-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Jiri Slaby authored
commit 368301f2 upstream. With this command sequence: modprobe plip modprobe pps_parport rmmod pps_parport the partport_pps modules causes this crash: BUG: unable to handle kernel NULL pointer dereference at (null) IP: parport_detach+0x1d/0x60 [pps_parport] Oops: 0000 [#1] SMP ... Call Trace: parport_unregister_driver+0x65/0xc0 [parport] SyS_delete_module+0x187/0x210 The sequence that builds up to this is: 1) plip is loaded and takes the parport device for exclusive use: plip0: Parallel port at 0x378, using IRQ 7. 2) pps_parport then fails to grab the device: pps_parport: parallel port PPS client parport0: cannot grant exclusive access for device pps_parport pps_parport: couldn't register with parport0 3) rmmod of pps_parport is then killed because it tries to access pardev->name, but pardev (taken from port->cad) is NULL. So add a check for NULL in the test there too. Link: http://lkml.kernel.org/r/20160714115245.12651-1-jslaby@suse.czSigned-off-by:
Jiri Slaby <jslaby@suse.cz> Acked-by:
Rodolfo Giometti <giometti@enneenne.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Dmitry Vyukov authored
commit e41f501d upstream. If CONFIG_KASAN is enabled and gcc is configured with --disable-initfini-array and/or gold linker is used, gcc emits .ctors/.dtors and .text.startup/.text.exit sections instead of .init_array/.fini_array. .dtors section is not explicitly accounted in the linker script and messes vvar/percpu layout. We want: ffffffff822bfd80 D _edata ffffffff822c0000 D __vvar_beginning_hack ffffffff822c0000 A __vvar_page ffffffff822c0080 0000000000000098 D vsyscall_gtod_data ffffffff822c1000 A __init_begin ffffffff822c1000 D init_per_cpu__irq_stack_union ffffffff822c1000 A __per_cpu_load ffffffff822d3000 D init_per_cpu__gdt_page We got: ffffffff8279a600 D _edata ffffffff8279b000 A __vvar_page ffffffff8279c000 A __init_begin ffffffff8279c000 D init_per_cpu__irq_stack_union ffffffff8279c000 A __per_cpu_load ffffffff8279e000 D __vvar_beginning_hack ffffffff8279e080 0000000000000098 D vsyscall_gtod_data ffffffff827ae000 D init_per_cpu__gdt_page This happens because __vvar_page and .vvar get different addresses in arch/x86/kernel/vmlinux.lds.S: . = ALIGN(PAGE_SIZE); __vvar_page = .; .vvar : AT(ADDR(.vvar) - LOAD_OFFSET) { /* work around gold bug 13023 */ __vvar_beginning_hack = .; Discard .dtors/.fini_array/.text.exit, since we don't call dtors. Merge .text.startup into init text. Link: http://lkml.kernel.org/r/1467386363-120030-1-git-send-email-dvyukov@google.comSigned-off-by:
Dmitry Vyukov <dvyukov@google.com> Reviewed-by:
-
Mel Gorman authored
commit ef70b6f4 upstream. early_page_uninitialised looks up an arbitrary PFN. While a machine without node 0 will boot with "mm, page_alloc: Always return a valid node from early_pfn_to_nid", it works because it assumes that nodes are always in PFN order. This is not guaranteed so this patch adds robustness by always checking if the node being checked is online. Link: http://lkml.kernel.org/r/1468008031-3848-4-git-send-email-mgorman@techsingularity.netSigned-off-by:
Mel Gorman <mgorman@techsingularity.net> Acked-by:
David Rientjes <rientjes@google.com> Signed-off-by:
-
Mel Gorman authored
commit e4568d38 upstream. early_pfn_to_nid can return node 0 if a PFN is invalid on machines that has no node 0. A machine with only node 1 was observed to crash with the following message: BUG: unable to handle kernel paging request at 000000000002a3c8 PGD 0 Modules linked in: Hardware name: Supermicro H8DSP-8/H8DSP-8, BIOS 080011 06/30/2006 task: ffffffff81c0d500 ti: ffffffff81c00000 task.ti: ffffffff81c00000 RIP: reserve_bootmem_region+0x6a/0xef CR2: 000000000002a3c8 CR3: 0000000001c06000 CR4: 00000000000006b0 Call Trace: free_all_bootmem+0x4b/0x12a mem_init+0x70/0xa3 start_kernel+0x25b/0x49b The problem is that early_page_uninitialised uses the early_pfn_to_nid helper which returns node 0 for invalid PFNs. No caller of early_pfn_to_nid cares except early_page_uninitialised. This patch has early_pfn_to_nid always return a valid node. Link: http://lkml.kernel.org/r/1468008031-3848-3-git-send-email-mgorman@techsingularity.netSigned-off-by:
-
David Rientjes authored
commit a46cbf3b upstream. It's possible to isolate some freepages in a pageblock and then fail split_free_page() due to the low watermark check. In this case, we hit VM_BUG_ON() because the freeing scanner terminated early without a contended lock or enough freepages. This should never have been a VM_BUG_ON() since it's not a fatal condition. It should have been a VM_WARN_ON() at best, or even handled gracefully. Regardless, we need to terminate anytime the full pageblock scan was not done. The logic belongs in isolate_freepages_block(), so handle its state gracefully by terminating the pageblock loop and making a note to restart at the same pageblock next time since it was not possible to complete the scan this time. [rientjes@google.com: don't rescan pages in a pageblock] Link: http://lkml.kernel.org/r/alpine.DEB.2.10.1607111244150.83138@chino.kir.corp.google.com Link: http://lkml.kernel.org/r/alpine.DEB.2.10.1606291436300.145590@chino.kir.corp.google.comSigned-off-by:
Minchan Kim <minchan@kernel.org> Tested-by:
-
Torsten Hilbrich authored
commit 63d2f95d upstream. The value `bytes' comes from the filesystem which is about to be mounted. We cannot trust that the value is always in the range we expect it to be. Check its value before using it to calculate the length for the crc32_le call. It value must be larger (or equal) sumoff + 4. This fixes a kernel bug when accidentially mounting an image file which had the nilfs2 magic value 0x3434 at the right offset 0x406 by chance. The bytes 0x01 0x00 were stored at 0x408 and were interpreted as a s_bytes value of 1. This caused an underflow when substracting sumoff + 4 (20) in the call to crc32_le. BUG: unable to handle kernel paging request at ffff88021e600000 IP: crc32_le+0x36/0x100 ... Call Trace: nilfs_valid_sb.part.5+0x52/0x60 [nilfs2] nilfs_load_super_block+0x142/0x300 [nilfs2] init_nilfs+0x60/0x390 [nilfs2] nilfs_mount+0x302/0x520 [nilfs2] mount_fs+0x38/0x160 vfs_kern_mount+0x67/0x110 do_mount+0x269/0xe00 SyS_mount+0x9f/0x100 entry_SYSCALL_64_fastpath+0x16/0x71 Link: http://lkml.kernel.org/r/1466778587-5184-2-git-send-email-konishi.ryusuke@lab.ntt.co.jpSigned-off-by:
Torsten Hilbrich <torsten.hilbrich@secunet.com> Tested-by:
Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp> Signed-off-by:
-
David Rientjes authored
commit a4f04f2c upstream. If the memory compaction free scanner cannot successfully split a free page (only possible due to per-zone low watermark), terminate the free scanner rather than continuing to scan memory needlessly. If the watermark is insufficient for a free page of order <= cc->order, then terminate the scanner since all future splits will also likely fail. This prevents the compaction freeing scanner from scanning all memory on very large zones (very noticeable for zones > 128GB, for instance) when all splits will likely fail while holding zone->lock. compaction_alloc() iterating a 128GB zone has been benchmarked to take over 400ms on some systems whereas any free page isolated and ready to be split ends up failing in split_free_page() because of the low watermark check and thus the iteration continues. The next time compaction occurs, the freeing scanner will likely start at the end of the zone again since no success was made previously and we get the same lengthy iteration until the zone is brought above the low watermark. All thp page faults can take >400ms in such a state without this fix. Link: http://lkml.kernel.org/r/alpine.DEB.2.10.1606211820350.97086@chino.kir.corp.google.comSigned-off-by:
Vlastimil Babka <vbabka@suse.cz> Cc: Minchan Kim <minchan@kernel.org> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Mel Gorman <mgorman@techsingularity.net> Cc: Hugh Dickins <hughd@google.com> Signed-off-by:
-
Mel Gorman authored
commit e838a45f upstream. Commit d0164adc ("mm, page_alloc: distinguish between being unable to sleep, unwilling to sleep and avoiding waking kswapd") modified __GFP_WAIT to explicitly identify the difference between atomic callers and those that were unwilling to sleep. Later the definition was removed entirely. The GFP_RECLAIM_MASK is the set of flags that affect watermark checking and reclaim behaviour but __GFP_ATOMIC was never added. Without it, atomic users of the slab allocator strip the __GFP_ATOMIC flag and cannot access the page allocator atomic reserves. This patch addresses the problem. The user-visible impact depends on the workload but potentially atomic allocations unnecessarily fail without this path. Link: http://lkml.kernel.org/r/20160610093832.GK2527@techsingularity.netSigned-off-by:
Marcin Wojtas <mw@semihalf.com> Acked-by:
Michal Hocko <mhocko@suse.com> Signed-off-by:
-
Ludovic Desroches authored
commit 9295c41d upstream. Due to the way CUBC register is updated, a double flush is needed to compute an accurate residue. First flush aim is to get data from the DMA FIFO and second one ensures that we won't report data which are not in memory. Signed-off-by:
Ludovic Desroches <ludovic.desroches@atmel.com> Fixes: e1f7c9ee ("dmaengine: at_xdmac: creation of the atmel eXtended DMA Controller driver") Reviewed-by:
Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by:
Vinod Koul <vinod.koul@intel.com> Signed-off-by:
-
Ludovic Desroches authored
commit 53398f48 upstream. An unexpected value of CUBC can lead to a corrupted residue. A more complex sequence is needed to detect an inaccurate value for NCA or CUBC. Signed-off-by:
-
Ludovic Desroches authored
commit 4a9723e8 upstream. Having descriptors aligned on 64 bits allows update CNDA and CUBC in an atomic way. Signed-off-by:
-
Lukas Wunner authored
commit abb2bafd upstream. The EFI firmware on Macs contains a full-fledged network stack for downloading OS X images from osrecovery.apple.com. Unfortunately on Macs introduced 2011 and 2012, EFI brings up the Broadcom 4331 wireless card on every boot and leaves it enabled even after ExitBootServices has been called. The card continues to assert its IRQ line, causing spurious interrupts if the IRQ is shared. It also corrupts memory by DMAing received packets, allowing for remote code execution over the air. This only stops when a driver is loaded for the wireless card, which may be never if the driver is not installed or blacklisted. The issue seems to be constrained to the Broadcom 4331. Chris Milsted has verified that the newer Broadcom 4360 built into the MacBookPro11,3 (2013/2014) does not exhibit this behaviour. The chances that Apple will ever supply a firmware fix for the older machines appear to be zero. The solution is to reset the card on boot by writing to a reset bit in its mmio space. This must be done as an early quirk and not as a plain vanilla PCI quirk to successfully combat memory corruption by DMAed packets: Matthew Garrett found out in 2012 that the packets are written to EfiBootServicesData memory (http://mjg59.dreamwidth.org/11235.html). This type of memory is made available to the page allocator by efi_free_boot_services(). Plain vanilla PCI quirks run much later, in subsys initcall level. In-between a time window would be open for memory corruption. Random crashes occurring in this time window and attributed to DMAed packets have indeed been observed in the wild by Chris Bainbridge. When Matthew Garrett analyzed the memory corruption issue in 2012, he sought to fix it with a grub quirk which transitions the card to D3hot: http://git.savannah.gnu.org/cgit/grub.git/commit/?id=9d34bb85da56 This approach does not help users with other bootloaders and while it may prevent DMAed packets, it does not cure the spurious interrupts emanating from the card. Unfortunately the card's mmio space is inaccessible in D3hot, so to reset it, we have to undo the effect of Matthew's grub patch and transition the card back to D0. Note that the quirk takes a few shortcuts to reduce the amount of code: The size of BAR 0 and the location of the PM capability is identical on all affected machines and therefore hardcoded. Only the address of BAR 0 differs between models. Also, it is assumed that the BCMA core currently mapped is the 802.11 core. The EFI driver seems to always take care of this. Michael Büsch, Bjorn Helgaas and Matt Fleming contributed feedback towards finding the best solution to this problem. The following should be a comprehensive list of affected models: iMac13,1 2012 21.5" [Root Port 00:1c.3 = 8086:1e16] iMac13,2 2012 27" [Root Port 00:1c.3 = 8086:1e16] Macmini5,1 2011 i5 2.3 GHz [Root Port 00:1c.1 = 8086:1c12] Macmini5,2 2011 i5 2.5 GHz [Root Port 00:1c.1 = 8086:1c12] Macmini5,3 2011 i7 2.0 GHz [Root Port 00:1c.1 = 8086:1c12] Macmini6,1 2012 i5 2.5 GHz [Root Port 00:1c.1 = 8086:1e12] Macmini6,2 2012 i7 2.3 GHz [Root Port 00:1c.1 = 8086:1e12] MacBookPro8,1 2011 13" [Root Port 00:1c.1 = 8086:1c12] MacBookPro8,2 2011 15" [Root Port 00:1c.1 = 8086:1c12] MacBookPro8,3 2011 17" [Root Port 00:1c.1 = 8086:1c12] MacBookPro9,1 2012 15" [Root Port 00:1c.1 = 8086:1e12] MacBookPro9,2 2012 13" [Root Port 00:1c.1 = 8086:1e12] MacBookPro10,1 2012 15" [Root Port 00:1c.1 = 8086:1e12] MacBookPro10,2 2012 13" [Root Port 00:1c.1 = 8086:1e12] For posterity, spurious interrupts caused by the Broadcom 4331 wireless card resulted in splats like this (stacktrace omitted): irq 17: nobody cared (try booting with the "irqpoll" option) handlers: [<ffffffff81374370>] pcie_isr [<ffffffffc0704550>] sdhci_irq [sdhci] threaded [<ffffffffc07013c0>] sdhci_thread_irq [sdhci] [<ffffffffc0a0b960>] azx_interrupt [snd_hda_codec] Disabling IRQ #17 Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=79301 Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=111781 Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=728916 Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=895951#c16 Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1009819 Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1098621 Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1149632#c5 Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1279130 Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1332732 Tested-by: Konstantin Simanov <k.simanov@stlk.ru> # [MacBookPro8,1] Tested-by: Lukas Wunner <lukas@wunner.de> # [MacBookPro9,1] Tested-by: Bryan Paradis <bryan.paradis@gmail.com> # [MacBookPro9,2] Tested-by: Andrew Worsley <amworsley@gmail.com> # [MacBookPro10,1] Tested-by: Chris Bainbridge <chris.bainbridge@gmail.com> # [MacBookPro10,2] Signed-off-by:
Lukas Wunner <lukas@wunner.de> Acked-by:
Rafał Miłecki <zajec5@gmail.com> Acked-by:
Matt Fleming <matt@codeblueprint.co.uk> Cc: Andy Lutomirski <luto@kernel.org> Cc: Bjorn Helgaas <bhelgaas@google.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Chris Milsted <cmilsted@redhat.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Matthew Garrett <mjg59@srcf.ucam.org> Cc: Michael Buesch <m@bues.ch> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Yinghai Lu <yinghai@kernel.org> Cc: b43-dev@lists.infradead.org Cc: linux-pci@vger.kernel.org Cc: linux-wireless@vger.kernel.org Link: http://lkml.kernel.org/r/48d0972ac82a53d460e5fce77a07b2560db95203.1465690253.git.lukas@wunner.de [ Did minor readability edits. ] Signed-off-by:
-
Lukas Wunner authored
commit 850c3210 upstream. We used to scan secondary buses until the following commit that was applied in 2009: 8659c406 ("x86: only scan the root bus in early PCI quirks") which commit constrained early quirks to the root bus only. Its motivation was to prevent application of the nvidia_bugs quirk on secondary buses. We're about to add a quirk to reset the Broadcom 4331 wireless card on 2011/2012 Macs, which is located on a secondary bus behind a PCIe root port. To facilitate that, reintroduce scanning of secondary buses. The commit message of 8659c406 notes that scanning only the root bus "saves quite some unnecessary scanning work". The algorithm used prior to 8659c406 was particularly time consuming because it scanned buses 0 to 31 brute force. To avoid lengthening boot time, employ a recursive strategy which only scans buses that are actually reachable from the root bus. Yinghai Lu pointed out that the secondary bus number read from a bridge's config space may be invalid, in particular a value of 0 would cause an infinite loop. The PCI core goes beyond that and recurses to a child bus only if its bus number is greater than the parent bus number (see pci_scan_bridge()). Since the root bus is numbered 0, this implies that secondary buses may not be 0. Do the same on early scanning. If this algorithm is found to significantly impact boot time or cause infinite loops on broken hardware, it would be possible to limit its recursion depth: The Broadcom 4331 quirk applies at depth 1, all others at depth 0, so the bus need not be scanned deeper than that for now. An alternative approach would be to revert to scanning only the root bus, and apply the Broadcom 4331 quirk to the root ports 8086:1c12, 8086:1e12 and 8086:1e16. Apple always positioned the card behind either of these three ports. The quirk would then check presence of the card in slot 0 below the root port and do its deed. Signed-off-by:
-
Lukas Wunner authored
commit 447d29d1 upstream. Since the following commit: 8659c406 ("x86: only scan the root bus in early PCI quirks") ... early quirks are only applied to devices on the root bus. The motivation was to prevent application of the nvidia_bugs quirk on secondary buses. We're about to reintroduce scanning of secondary buses for a quirk to reset the Broadcom 4331 wireless card on 2011/2012 Macs. To prevent regressions, open code the requirement to apply nvidia_bugs only on the root bus. Signed-off-by:
-
Michał Pecio authored
commit c66f59ee upstream. Since ed_schedule begins with marking the ED as "operational", the ED may be left in such state even if scheduling actually fails. This allows future submission attempts to smuggle this ED to the hardware behind the scheduler's back and without linking it to the ohci->eds_in_use list. The former causes bandwidth saturation and data loss on isoc endpoints, the latter crashes the kernel when attempt is made to unlink such ED from this list. Fix ed_schedule to update ED state only on successful return. Signed-off-by:
Michal Pecio <michal.pecio@gmail.com> Acked-by:
Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
-
- 27 Jul, 2016 7 commits
-
-
Greg Kroah-Hartman authored
-
Miklos Szeredi authored
commit 11f37104 upstream. Unlink and rename in overlayfs checked the upper dentry for staleness by verifying upper->d_parent against upperdir. However the dentry can go stale also by being unhashed, for example. Expand the verification to actually look up the name again (under parent lock) and check if it matches the upper dentry. This matches what the VFS does before passing the dentry to filesytem's unlink/rename methods, which excludes any inconsistency caused by overlayfs. Signed-off-by:
Miklos Szeredi <mszeredi@redhat.com> Signed-off-by:
-
Mika Kahola authored
commit 34511dce upstream. It has been found out that in some HW combination the DisplayPort fast link training feature caused screen flickering. Let's revert this feature for now until we can ensure that the feature works for all platforms. This is a manual revert of commits 5fa836a9 ("drm/i915: DP link training optimization") and 4e96c977 ("drm/i915: eDP link training optimization"). Fixes: 5fa836a9 ("drm/i915: DP link training optimization") Fixes: 4e96c977 ("drm/i915: eDP link training optimization") Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91393Reviewed-by:
Jani Nikula <jani.nikula@intel.com> Signed-off-by:
Mika Kahola <mika.kahola@intel.com> Signed-off-by:
Joakim Tjernlund <joakim.tjernlund@infinera.com> Signed-off-by:
-
Hugh Dickins authored
commit 7f556567 upstream. The well-spotted fallocate undo fix is good in most cases, but not when fallocate failed on the very first page. index 0 then passes lend -1 to shmem_undo_range(), and that has two bad effects: (a) that it will undo every fallocation throughout the file, unrestricted by the current range; but more importantly (b) it can cause the undo to hang, because lend -1 is treated as truncation, which makes it keep on retrying until every page has gone, but those already fully instantiated will never go away. Big thank you to xfstests generic/269 which demonstrates this. Fixes: b9b4bb26 ("tmpfs: don't undo fallocate past its last page") Signed-off-by:
Hugh Dickins <hughd@google.com> Signed-off-by:
-
Anthony Romano authored
commit b9b4bb26 upstream. When fallocate is interrupted it will undo a range that extends one byte past its range of allocated pages. This can corrupt an in-use page by zeroing out its first byte. Instead, undo using the inclusive byte range. Fixes: 1635f6a7 ("tmpfs: undo fallocation on failure") Link: http://lkml.kernel.org/r/1462713387-16724-1-git-send-email-anthony.romano@coreos.comSigned-off-by:
Anthony Romano <anthony.romano@coreos.com> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: Hugh Dickins <hughd@google.com> Cc: Brandon Philips <brandon@ifup.co> Signed-off-by:
-
Jan Stancek authored
commit 81dc0365 upstream. Parallel build can sporadically fail because asn1 headers may not be built yet by the time qat_asym_algs.o is compiled: drivers/crypto/qat/qat_common/qat_asym_algs.c:55:32: fatal error: qat_rsapubkey-asn1.h: No such file or directory #include "qat_rsapubkey-asn1.h" Signed-off-by:
Jan Stancek <jstancek@redhat.com> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Jan Beulich authored
commit 6f2d9d99 upstream. As of Xen 4.7 PV CPUID doesn't expose either of CPUID[1].ECX[7] and CPUID[0x80000007].EDX[7] anymore, causing the driver to fail to load on both Intel and AMD systems. Doing any kind of hardware capability checks in the driver as a prerequisite was wrong anyway: With the hypervisor being in charge, all such checking should be done by it. If ACPI data gets uploaded despite some missing capability, the hypervisor is free to ignore part or all of that data. Ditch the entire check_prereq() function, and do the only valid check (xen_initial_domain()) in the caller in its place. Signed-off-by:
-
