Commit 2aa0102c ("scsi: ibmvfc: Use correlation token to tag commands")
sets the vfcFrame correlation token to the pointer handle of the associated
ibmvfc_event. However, that commit failed to cast the pointer to an
appropriate type which in this case is a u64. As such sparse warnings are
generated for both correlation token assignments.

 ibmvfc.c:2375:36: sparse: incorrect type in argument 1 (different base types)
 ibmvfc.c:2375:36: sparse: expected unsigned long long [usertype] val
 ibmvfc.c:2375:36: sparse: got struct ibmvfc_event *[assigned] evt

Add the appropriate u64 casts when assigning an ibmvfc_event as a
correlation token.

Link: https://lore.kernel.org/r/20210106203721.1054693-1-tyreld@linux.ibm.com
Fixes: 2aa0102c ("scsi: ibmvfc: Use correlation token to tag commands")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Building ufshcd-pltfrm.c on arch/s390/ has a linker error since S390 does
not support IOMEM, so add a dependency on HAS_IOMEM.

s390-linux-ld: drivers/scsi/ufs/ufshcd-pltfrm.o: in function `ufshcd_pltfrm_init':
ufshcd-pltfrm.c:(.text+0x38e): undefined reference to `devm_platform_ioremap_resource'

where that devm_ function is inside an #ifdef CONFIG_HAS_IOMEM/#endif
block.

Link: lore.kernel.org/r/202101031125.ZEFCUiKi-lkp@intel.com
Link: https://lore.kernel.org/r/20210106040822.933-1-rdunlap@infradead.org
Fixes: 03b1781a ("[SCSI] ufs: Add Platform glue driver for ufshcd")
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Alim Akhtar <alim.akhtar@samsung.com>
Cc: Avri Altman <avri.altman@wdc.com>
Cc: linux-scsi@vger.kernel.org
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Phil Oester reported that a fix for a possible buffer overrun that I sent
caused a regression that manifests in this output:

 Event Message: A PCI parity error was detected on a component at bus 0 device 5 function 0.
 Severity: Critical
 Message ID: PCI1308

The original code tried to handle the sense data pointer differently when
using 32-bit 64-bit DMA addressing, which would lead to a 32-bit dma_addr_t
value of 0x11223344 to get stored

32-bit kernel:       44 33 22 11 ?? ?? ?? ??
64-bit LE kernel:    44 33 22 11 00 00 00 00
64-bit BE kernel:    00 00 00 00 44 33 22 11

or a 64-bit dma_addr_t value of 0x1122334455667788 to get stored as

32-bit kernel:       88 77 66 55 ?? ?? ?? ??
64-bit kernel:       88 77 66 55 44 33 22 11

In my patch, I tried to ensure that the same value is used on both 32-bit
and 64-bit kernels, and picked what seemed to be the most sensible
combination, storing 32-bit addresses in the first four bytes (as 32-bit
kernels already did), and 64-bit addresses in eight consecutive bytes (as
64-bit kernels already did), but evidently this was incorrect.

Always storing the dma_addr_t pointer as 64-bit little-endian,
i.e. initializing the second four bytes to zero in case of 32-bit
addressing, apparently solved the problem for Phil, and is consistent with
what all 64-bit little-endian machines did before.

I also checked in the history that in previous versions of the code, the
pointer was always in the first four bytes without padding, and that
previous attempts to fix 64-bit user space, big-endian architectures and
64-bit DMA were clearly flawed and seem to have introduced made this worse.

Link: https://lore.kernel.org/r/20210104234137.438275-1-arnd@kernel.org
Fixes: 381d34e3 ("scsi: megaraid_sas: Check user-provided offsets")
Fixes: 107a60dd ("scsi: megaraid_sas: Add support for 64bit consistent DMA")
Fixes: 94cd65dd ("[SCSI] megaraid_sas: addded support for big endian architecture")
Fixes: 7b2519af ("[SCSI] megaraid_sas: fix 64 bit sense pointer truncation")
Reported-by: Phil Oester <kernel@linuxace.com>
Tested-by: Phil Oester <kernel@linuxace.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Update sysfs documentation for addition of DeepSleep power mode.

Link: https://lore.kernel.org/r/20210104155026.16417-1-adrian.hunter@intel.com
Fixes: fe1d4c2e ("scsi: ufs: Add DeepSleep feature")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Commit 996e509b ("sd: use __register_blkdev to avoid a modprobe for an
unregistered dev_t") removed blk_register_region(devt, ...) in sd_remove()
and since then, devt is unused in sd_remove().

Hence, make W=1 warns:

  drivers/scsi/sd.c:3516:8:
      warning: variable 'devt' set but not used [-Wunused-but-set-variable]

Simply remove this obsolete variable.

[mkp: fixed commit sha]

Link: https://lore.kernel.org/r/20201214095424.12479-1-lukas.bulwahn@gmail.comReviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

The block layer code will split a large zeroout request into multiple bios
and if WRITE SAME is disabled because the storage device reports that it
does not support it (or support the length used), we can get an error
message from the block layer despite the setting of RQF_QUIET on the first
request.  This is because more than one request may have already been
submitted.

Fix this by setting RQF_QUIET when BLK_STS_TARGET is returned to fail the
request early, we don't need to log a message because we did not actually
submit the command to the device, and the block layer code will handle the
error by submitting individual write bios.

Link: https://lore.kernel.org/r/20201207221021.28243-1-emilne@redhat.comReviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

When sdeb_zbc_model does not match BLK_ZONED_NONE, BLK_ZONED_HA or
BLK_ZONED_HM, we should free sdebug_q_arr to prevent memleak. Also there is
no need to execute sdebug_erase_store() on failure of sdeb_zbc_model_str().

Link: https://lore.kernel.org/r/20201226061503.20050-1-dinghao.liu@zju.edu.cnAcked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

There is a spelling mistake in the Kconfig help text. Fix it.

Link: https://lore.kernel.org/r/20201217172019.57768-1-colin.king@canonical.comSigned-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

The CHAP secret displayed garbage characters causing iSCSI login
authentication failure. Correct the CHAP password max length.

Link: https://lore.kernel.org/r/20201217105144.8055-1-njavali@marvell.comReviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Users can initiate resets to specific SCSI device/target/host through
IOCTL. When this happens, the SCSI cmd passed to eh_device/target/host
_reset_handler() callbacks is initialized with a request whose tag is -1.
In this case it is not right for eh_device_reset_handler() callback to
count on the LUN get from hba->lrb[-1]. Fix it by getting LUN from the SCSI
device associated with the SCSI cmd.

Link: https://lore.kernel.org/r/1609157080-26283-1-git-send-email-cang@codeaurora.orgReviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

The current flush location does not guarantee disabling BKOPS for the case
of requesting device power off.

 1) The exceptional event handler is queued

 2) ufs suspend starts with a request of device power off

 3) BKOPS is disabled in ufs suspend

 4) The queued work for the handler is done and BKOPS is re-enabled

Relocate the flush statement to ensure BKOPS remain disabled.

Link: https://lore.kernel.org/r/1608360039-16390-1-git-send-email-kwmad.kim@samsung.comReviewed-by: Can Guo <cang@codeaurora.org>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Kiwoong Kim <kwmad.kim@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

UFSHCI_QUIRK_SKIP_MANUAL_WB_FLUSH_CTRL is intended to skip enabling
fWriteBoosterBufferFlushEn while WriteBooster is initializing.  Therefore
it is better to apply the checking during WriteBooster initialization only.

Link: https://lore.kernel.org/r/20201222072905.32221-3-stanley.chu@mediatek.comReviewed-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Currently if device needs to do flush or BKOP operations, the device VCC
power is kept during runtime-suspend period.

However, if system suspend is happening while device is runtime-suspended,
such power may not be disabled successfully.

The reasons may be,

1. If current PM level is the same as SPM level, device will keep
   runtime-suspended by ufshcd_system_suspend().

2. Flush recheck work may not be scheduled successfully during system
   suspend period. If it can wake up the system, this is also not the
   intention of the recheck work.

To fix this issue, simply runtime-resume the device if the flush is allowed
during runtime suspend period. Flush capability will be disabled while
leaving runtime suspend, and also not be allowed in system suspend period.

Link: https://lore.kernel.org/r/20201222072905.32221-2-stanley.chu@mediatek.com
Fixes: 51dd905b ("scsi: ufs: Fix WriteBooster flush during runtime suspend")
Reviewed-by: Chaotian Jing <chaotian.jing@mediatek.com>
Reviewed-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Merge two commits that had dependencies on other 5.11 trees (the block
and the irq trees respectively).

 - We reverted a megaraid_sas change in 5.10 due to missing block
   layer plumbing. Now that this is in place, reinstate the change.

 - The hisi_sas driver had a dependency on a driver core irq change
   that went in through Thomas' tree.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

Pull s390 cleanups from Vasily Gorbik:
 "Update defconfigs and sort config select list"

* tag 's390-5.11-3' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390/Kconfig: sort config S390 select list once again
  s390: update defconfigs

Pull power management fixes from Rafael Wysocki:
 "These fix a crash in intel_pstate during resume from suspend-to-RAM
  that may occur after recent changes and two resource leaks in error
  paths in the operating performance points (OPP) framework, add a new
  C-states table to intel_idle and update the cpuidle MAINTAINERS entry
  to cover the governors too.

  Specifics:

   - Fix recently introduced crash in the intel_pstate driver that
     occurs if scale-invariance is disabled during resume from
     suspend-to-RAM due to inconsistent changes of APERF or MPERF MSR
     values made by the platform firmware (Rafael Wysocki).

   - Fix a memory leak and add a missing clk_put() in error paths in the
     OPP framework (Quanyang Wang, Viresh Kumar).

   - Add new C-states table for SnowRidge processors to the intel_idle
     driver (Artem Bityutskiy).

   - Update the MAINTAINERS entry for cpuidle to make it clear that the
     governors are covered by it too (Lukas Bulwahn)"

* tag 'pm-5.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  intel_idle: add SnowRidge C-state table
  cpufreq: intel_pstate: Fix fast-switch fallback path
  opp: Call the missing clk_put() on error
  opp: fix memory leak in _allocate_opp_table
  MAINTAINERS: include governors into CPU IDLE TIME MANAGEMENT FRAMEWORK

* pm-cpufreq:
  cpufreq: intel_pstate: Fix fast-switch fallback path

* pm-cpuidle:
  intel_idle: add SnowRidge C-state table
  MAINTAINERS: include governors into CPU IDLE TIME MANAGEMENT FRAMEWORK

Pull SCSI fixes from James Bottomley:
 "This is a load of driver fixes (12 ufs, 1 mpt3sas, 1 cxgbi).

  The big core two fixes are for power management ("block: Do not accept
  any requests while suspended" and "block: Fix a race in the runtime
  power management code") which finally sorts out the resume problems
  we've occasionally been having.

  To make the resume fix, there are seven necessary precursors which
  effectively renames REQ_PREEMPT to REQ_PM, so every "special" request
  in block is automatically a power management exempt one.

  All of the non-PM preempt cases are removed except for the one in the
  SCSI Parallel Interface (spi) domain validation which is a genuine
  case where we have to run requests at high priority to validate the
  bus so this becomes an autopm get/put protected request"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (22 commits)
  scsi: cxgb4i: Fix TLS dependency
  scsi: ufs: Un-inline ufshcd_vops_device_reset function
  scsi: ufs: Re-enable WriteBooster after device reset
  scsi: ufs-mediatek: Use correct path to fix compile error
  scsi: mpt3sas: Signedness bug in _base_get_diag_triggers()
  scsi: block: Do not accept any requests while suspended
  scsi: block: Remove RQF_PREEMPT and BLK_MQ_REQ_PREEMPT
  scsi: core: Only process PM requests if rpm_status != RPM_ACTIVE
  scsi: scsi_transport_spi: Set RQF_PM for domain validation commands
  scsi: ide: Mark power management requests with RQF_PM instead of RQF_PREEMPT
  scsi: ide: Do not set the RQF_PREEMPT flag for sense requests
  scsi: block: Introduce BLK_MQ_REQ_PM
  scsi: block: Fix a race in the runtime power management code
  scsi: ufs-pci: Enable UFSHCD_CAP_RPM_AUTOSUSPEND for Intel controllers
  scsi: ufs-pci: Fix recovery from hibernate exit errors for Intel controllers
  scsi: ufs-pci: Ensure UFS device is in PowerDown mode for suspend-to-disk ->poweroff()
  scsi: ufs-pci: Fix restore from S4 for Intel controllers
  scsi: ufs-mediatek: Keep VCC always-on for specific devices
  scsi: ufs: Allow regulators being always-on
  scsi: ufs: Clear UAC for RPMB after ufshcd resets
  ...

Pull block fixes from Jens Axboe:
 "Two minor block fixes from this last week that should go into 5.11:

   - Add missing NOWAIT debugfs definition (Andres)

   - Fix kerneldoc warning introduced this merge window (Randy)"

* tag 'block-5.11-2021-01-01' of git://git.kernel.dk/linux-block:
  block: add debugfs stanza for QUEUE_FLAG_NOWAIT
  fs: block_dev.c: fix kernel-doc warnings from struct block_device changes

Pull io_uring fixes from Jens Axboe:
 "A few fixes that should go into 5.11, all marked for stable as well:

   - Fix issue around identity COW'ing and users that share a ring
     across processes

   - Fix a hang associated with unregistering fixed files (Pavel)

   - Move the 'process is exiting' cancelation a bit earlier, so
     task_works aren't affected by it (Pavel)"

* tag 'io_uring-5.11-2021-01-01' of git://git.kernel.dk/linux-block:
  kernel/io_uring: cancel io_uring before task works
  io_uring: fix io_sqe_files_unregister() hangs
  io_uring: add a helper for setting a ref node
  io_uring: don't assume mm is constant across submits

Commit 436e980e ("kbuild: don't hardcode depmod path") stopped
hard-coding the path of depmod, but in the process caused trouble for
distributions that had that /sbin location, but didn't have it in the
PATH (generally because /sbin is limited to the super-user path).

Work around it for now by just adding /sbin to the end of PATH in the
depmod.sh script.
Reported-and-tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

For cancelling io_uring requests it needs either to be able to run
currently enqueued task_works or having it shut down by that moment.
Otherwise io_uring_cancel_files() may be waiting for requests that won't
ever complete.

Go with the first way and do cancellations before setting PF_EXITING and
so before putting the task_work infrastructure into a transition state
where task_work_run() would better not be called.

Cc: stable@vger.kernel.org # 5.5+
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

io_sqe_files_unregister() uninterruptibly waits for enqueued ref nodes,
however requests keeping them may never complete, e.g. because of some
userspace dependency. Make sure it's interruptible otherwise it would
hang forever.

Cc: stable@vger.kernel.org # 5.6+
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Setting a new reference node to a file data is not trivial, don't repeat
it, add and use a helper.

Cc: stable@vger.kernel.org # 5.6+
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Pull ceph fixes from Ilya Dryomov:
 "A fix for an edge case in MClientRequest encoding and a couple of
  trivial fixups for the new msgr2 support"

* tag 'ceph-for-5.11-rc2' of git://github.com/ceph/ceph-client:
  libceph: add __maybe_unused to DEFINE_MSGR2_FEATURE
  libceph: align session_key and con_secret to 16 bytes
  libceph: fix auth_signature buffer allocation in secure mode
  ceph: reencode gid_list when reconnecting

Add C-state table for the SnowRidge SoC which is found on Intel Jacobsville
platforms.

The following has been changed.

 1. C1E latency changed from 10us to 15us. It was measured using the
    open source "wult" tool (the "nic" method, 15us is the 99.99th
    percentile).

 2. C1E power break even changed from 20us to 25us, which may result
    in less C1E residency in some workloads.

 3. C6 latency changed from 50us to 130us. Measured the same way as C1E.

The C6 C-state is supported only by some SnowRidge revisions, so add a C-state
table commentary about this.

On SnowRidge, C6 support is enumerated via the usual mechanism: "mwait" leaf of
the "cpuid" instruction. The 'intel_idle' driver does check this leaf, so even
though C6 is present in the table, the driver will only use it if the CPU does
support it.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

When sugov_update_single_perf() falls back to the "frequency"
path due to the missing scale-invariance, it will call
cpufreq_driver_fast_switch() via sugov_fast_switch()
and the driver's ->fast_switch() callback will be invoked,
so it must not be NULL.

However, after commit a365ab6b ("cpufreq: intel_pstate: Implement
the ->adjust_perf() callback") intel_pstate sets ->fast_switch() to
NULL when it is going to use intel_cpufreq_adjust_perf(), which is a
mistake, because on x86 the scale-invariance may be turned off
dynamically, so modify it to retain the original ->adjust_perf()
callback pointer.

Fixes: a365ab6b ("cpufreq: intel_pstate: Implement the ->adjust_perf() callback")
Reported-by: Kenneth R. Crudup <kenny@panix.com>
Tested-by: Kenneth R. Crudup <kenny@panix.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

Pull operating performance points (OPP) framework fixes for 5.11-rc2
from Viresh Kumar:

"This contains two patches to fix freeing of resources in error paths."

* 'opp/linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm:
  opp: Call the missing clk_put() on error
  opp: fix memory leak in _allocate_opp_table

...and add comments at the top and bottom.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>

Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>

This was missed in 021a2446. Leads to the numeric value of
QUEUE_FLAG_NOWAIT (i.e. 29) showing up in
/sys/kernel/debug/block/*/state.

Fixes: 021a2446
Cc: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andres Freund <andres@anarazel.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Fix new kernel-doc warnings in fs/block_dev.c:

../fs/block_dev.c:1066: warning: Excess function parameter 'whole' description in 'bd_abort_claiming'
../fs/block_dev.c:1837: warning: Function parameter or member 'dev' not described in 'lookup_bdev'

Fixes: 4e7b5671 ("block: remove i_bdev")
Fixes: 37c3fc9a ("block: simplify the block device claiming interface")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Christoph Hellwig <hch@lst.de>
Cc: linux-fsdevel@vger.kernel.org
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Merge misc fixes from Andrew Morton:
 "16 patches

  Subsystems affected by this patch series: mm (selftests, hugetlb,
  pagecache, mremap, kasan, and slub), kbuild, checkpatch, misc, and
  lib"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  mm: slub: call account_slab_page() after slab page initialization
  zlib: move EXPORT_SYMBOL() and MODULE_LICENSE() out of dfltcc_syms.c
  lib/zlib: fix inflating zlib streams on s390
  lib/genalloc: fix the overflow when size is too big
  kdev_t: always inline major/minor helper functions
  sizes.h: add SZ_8G/SZ_16G/SZ_32G macros
  local64.h: make <asm/local64.h> mandatory
  kasan: fix null pointer dereference in kasan_record_aux_stack
  mm: generalise COW SMC TLB flushing race comment
  mm/mremap.c: fix extent calculation
  mm: memmap defer init doesn't work as expected
  mm: add prototype for __add_to_page_cache_locked()
  checkpatch: prefer strscpy to strlcpy
  Revert "kbuild: avoid static_assert for genksyms"
  mm/hugetlb: fix deadlock in hugetlb_cow error path
  selftests/vm: fix building protection keys test

It's convenient to have page->objects initialized before calling into
account_slab_page().  In particular, this information can be used to
pre-alloc the obj_cgroup vector.

Let's call account_slab_page() a bit later, after the initialization of
page->objects.

This commit doesn't bring any functional change, but is required for
further optimizations.

[akpm@linux-foundation.org: undo changes needed by forthcoming mm-memcg-slab-pre-allocate-obj_cgroups-for-slab-caches-with-slab_account.patch]

Link: https://lkml.kernel.org/r/20201110195753.530157-1-guro@fb.comSigned-off-by: Roman Gushchin <guro@fb.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Reviewed-by: Shakeel Butt <shakeelb@google.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Christoph Lameter <cl@linux.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

In commit 11fb479f ("zlib: export S390 symbols for zlib modules"), I
added EXPORT_SYMBOL()s to dfltcc_inflate.c but then Mikhail said that
these should probably be in dfltcc_syms.c with the other
EXPORT_SYMBOL()s.

However, that is contrary to the current kernel style, which places
EXPORT_SYMBOL() immediately after the function that it applies to, so
move all EXPORT_SYMBOL()s to their respective function locations and
drop the dfltcc_syms.c file.  Also move MODULE_LICENSE() from the
deleted file to dfltcc.c.

[rdunlap@infradead.org: remove dfltcc_syms.o from Makefile]
  Link: https://lkml.kernel.org/r/20201227171837.15492-1-rdunlap@infradead.org

Link: https://lkml.kernel.org/r/20201219052530.28461-1-rdunlap@infradead.org
Fixes: 11fb479f ("zlib: export S390 symbols for zlib modules")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Acked-by: Ilya Leoshkevich <iii@linux.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Zaslonko Mikhail <zaslonko@linux.ibm.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Decompressing zlib streams on s390 fails with "incorrect data check"
error.

Userspace zlib checks inflate_state.flags in order to byteswap checksums
only for zlib streams, and s390 hardware inflate code, which was ported
from there, tries to match this behavior.  At the same time, kernel zlib
does not use inflate_state.flags, so it contains essentially random
values.  For many use cases either zlib stream is zeroed out or checksum
is not used, so this problem is masked, but at least SquashFS is still
affected.

Fix by always passing a checksum to and from the hardware as is, which
matches zlib_inflate()'s expectations.

Link: https://lkml.kernel.org/r/20201215155551.894884-1-iii@linux.ibm.com
Fixes: 12619610 ("lib/zlib: add s390 hardware support for kernel zlib_inflate")
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Tested-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Mikhail Zaslonko <zaslonko@linux.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Mikhail Zaslonko <zaslonko@linux.ibm.com>
Cc: <stable@vger.kernel.org>	[5.6+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Some graphic card has very big memory on chip, such as 32G bytes.

In the following case, it will cause overflow:

    pool = gen_pool_create(PAGE_SHIFT, NUMA_NO_NODE);
    ret = gen_pool_add(pool, 0x1000000, SZ_32G, NUMA_NO_NODE);

    va = gen_pool_alloc(pool, SZ_4G);

The overflow occurs in gen_pool_alloc_algo_owner():

		....
		size = nbits << order;
		....

The @nbits is "int" type, so it will overflow.
Then the gen_pool_avail() will return the wrong value.

This patch converts some "int" to "unsigned long", and
changes the compare code in while.

Link: https://lkml.kernel.org/r/20201229060657.3389-1-sjhuang@iluvatar.aiSigned-off-by: Huang Shijie <sjhuang@iluvatar.ai>
Reported-by: Shi Jiasheng <jiasheng.shi@iluvatar.ai>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Silly GCC doesn't always inline these trivial functions.

Fixes the following warning:

  arch/x86/kernel/sys_ia32.o: warning: objtool: cp_stat64()+0xd8: call to new_encode_dev() with UACCESS enabled

Link: https://lkml.kernel.org/r/984353b44a4484d86ba9f73884b7306232e25e30.1608737428.git.jpoimboe@redhat.comSigned-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org>	[build-tested]
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Add these macros, since we can use them in drivers.

Link: https://lkml.kernel.org/r/20201229072819.11183-1-sjhuang@iluvatar.aiSigned-off-by: Huang Shijie <sjhuang@iluvatar.ai>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>