struct timeval uses a 32-bit seconds representation which will
overflow in the year 2038 and beyond. This patch replaces
the usage of struct timeval with ktime_t which is a 64-bit
timestamp and is year 2038 safe.
This patch is part of a larger attempt to remove all instances
of 32-bit timekeeping variables (timeval, timespec, time_t)
which are not year 2038 safe, from the kernel.

[mchehab@osg.samsung.com: add a missing parenthesis, breaking compilation]
Suggested-by: Arnd Bergmann <arndb@arndb.de>
Signed-off-by: Tina Ruchandani <ruchandani.tina@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

The flexcop bridge chip has two banks of hardware pid filters -
an initial 6, and on some chip revisions an additional bank of 32.

A bug is present on the initial 6 - when changing transponders
one of two PAT packets from the old transponder would be included
in the initial packets from the new transponder. This usually
transpired with userspace programs complaining about services
missing, because they are seeing a PAT that they would not be
expecting. Running in full TS mode does not exhibit this problem,
neither does using just the additional 32.

This patch adds in an option to not use the inital 6 and solely use
just the additional 32, and enables this option for the SkystarS2
card. Other cards can be added as required if they also have
this bug.
Signed-off-by: Jemma Denson <jdenson@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

My static checker detected that free_irq() is called even after
request_irq() failed in ddb_probe(). In this case, the kernel may try to
free dev->pdev->irq although the IRQ is not assigned. This event rarely
occurs, but always introduces a warning if it happens.

"goto fail1" always results in disabling enabled MSI and releasing a
requested IRQ. It seems like the former handling is necessary. So I added
a conditional branch before the free_irq() (stat == 0 means request_irq()
succeeds).
Signed-off-by: Takeshi Yoshimura <yos@sslab.ics.keio.ac.jp>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

This reformats lines that were previously above 80 characters long,
improving readability and making checkpatch.pl happier.
Signed-off-by: Piotr S. Staszewski <p.staszewski@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

'struct timeval last_tv' is used to get the time of last signal change
and 'struct timeval last_intr_tv' is used to get the time of last UART
interrupt.
32-bit systems using 'struct timeval' will break in the year 2038, so we
have to replace that code with more appropriate types.
Here struct timeval is replaced with ktime_t.
Signed-off-by: Ksenija Stanojevic <ksenija.stanojevic@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

The card lists at Documentation/video4linux are missing some
boards. Add them.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Add AverMedia AverTV/505 card to saa7134 driver. It is a card bearing
SAA7130HL chip and FQ1216ME/IH-3 tuner.

Working: Composite, TV and IR remote control.
Untested: S-Video.

[mchehab@osg.samsung.com: fix CodingStyle]
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Compilation warning issued by kbuild test robot:
>> drivers/media/common/b2c2/flexcop-fe-tuner.c:31:12: warning: 'flexcop_fe_request_firmware' defined but not used [-Wunused-function]
    static int flexcop_fe_request_firmware(struct dvb_frontend *fe,

This patch fixes a mismatch in Kconfig define checks. One had a
check for just CX24120, the other is checking for both CX24120
and ISL6421.
Signed-off-by: Jemma Denson <jdenson@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Add support for the Terratec Grabby with USB ID 0ccd:00a6.
Signed-off-by: Tommi Rantala <tt.rantala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

The coda tracing code causes lots of warnings like

In file included from /git/arm-soc/include/trace/define_trace.h:90:0,
                 from /git/arm-soc/drivers/media/platform/coda/trace.h:203,
                 from /git/arm-soc/drivers/media/platform/coda/coda-bit.c:34:
/git/arm-soc/include/trace/ftrace.h:28:0: warning: "TRACE_SYSTEM_STRING" redefined
 #define TRACE_SYSTEM_STRING __app(TRACE_SYSTEM_VAR,__trace_system_name)
 ^
In file included from /git/arm-soc/include/trace/define_trace.h:83:0,
                 from /git/arm-soc/drivers/media/platform/coda/trace.h:203,
                 from /git/arm-soc/drivers/media/platform/coda/coda-bit.c:34:
/git/arm-soc/drivers/media/platform/coda/./trace.h:12:0: note: this is the location of the previous definition
 #define TRACE_SYSTEM_STRING __stringify(TRACE_SYSTEM)

>From what I can tell, this is just the result of a bogus TRACE_SYSTEM_STRING
definition, and removing that one makes the warnings go away.

Fixes: 9a1a8f99 ("[media] coda: Add tracing support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Some USB drivers have a logic at the VB buffer handling like:
	if (in_interrupt())
		BUG();
Use, instead:
	BUG_ON(in_interrupt());

Btw, this logic looks weird on my eyes. We should convert them
to use VB2, in order to avoid those crappy things.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

The subdev API is optional. No driver should depend on it.

Avoid compilation breakages if subdev API is not selected:

drivers/media/i2c/ov2659.c: In function ‘ov2659_get_fmt’:
drivers/media/i2c/ov2659.c:1054:3: error: implicit declaration of function ‘v4l2_subdev_get_try_format’ [-Werror=implicit-function-declaration]
   mf = v4l2_subdev_get_try_format(sd, cfg, 0);
   ^
drivers/media/i2c/ov2659.c:1054:6: warning: assignment makes pointer from integer without a cast
   mf = v4l2_subdev_get_try_format(sd, cfg, 0);
      ^
drivers/media/i2c/ov2659.c: In function ‘ov2659_set_fmt’:
drivers/media/i2c/ov2659.c:1129:6: warning: assignment makes pointer from integer without a cast
   mf = v4l2_subdev_get_try_format(sd, cfg, fmt->pad);
      ^
drivers/media/i2c/ov2659.c: In function ‘ov2659_open’:
drivers/media/i2c/ov2659.c:1264:38: error: ‘struct v4l2_subdev_fh’ has no member named ‘pad’
     v4l2_subdev_get_try_format(sd, fh->pad, 0);
                                      ^
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Tested-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>

Add entry for the bdisp driver to the MAINTAINERS file.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Creates 5 debugfs entries to dump the last HW request, the last HW node
(=command), the HW registers and the recent HW performance (time & fps)
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

This v4l2 mem2mem driver is a 2D blitter for STMicroelectronics SoC.
It uses the v4l2 mem2mem framework.

The following features are supported and tested:
- Color format conversion (RGB32, RGB24, RGB16, NV12, YUV420P)
- Copy
- Scale
- Flip
- Deinterlace
- Wide (4K) picture support
- Crop
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
[hans.verkuil@cisco.com: added missing slab.h include to bdisp-v4l2.c]
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

This adds DT binding documentation for STMicroelectronics bdisp driver.
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Use a table for the Demux output. No new information added
here. They were all merged inside the table.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

There are several anonymous enums here, used via a typedef.

Well, we don't like typedefs on Kernel, so let's de-anonimize
those enums. Then, latter, we may be able to get rid of the
typedefs, at least from Kernelspace.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Let be clear, at the header, about what got deprecated.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

The comment for struct dvb_frontend_parameters is weird, as it
mixes delivery system name (ATSC) with modulation names
(QPSK, QAM, OFDM).

Use delivery system names there on the frequency comment, as this
is clearer, specially after 2GEN delivery systems.

While here, add comments at the union, to make live easier for ones
that may try to understand the convention used by the legacy API.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

The description of struct dtv_stats has a spmall typo:
	FE_SCALE_DECIBELS instead of FE_SCALE_DECIBEL
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

The comments may affect enum value parsing. Use cpp to remove
them.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Just userspace need those typedefs. So, put it in the compat part
of the header.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

In order to better organize the header file, move the legacy
API (DVBv3) support to the end, just before the ioctl definitions.

This way, we can use just one #if for all of them.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

The DVB API was originally defined using typedefs. This is against
Kernel CodingStyle, and there's no good usage here. While we can't
remove its usage on userspace, we can avoid its usage in Kernelspace.

So, let's do it.

This patch was generated by this shell script:

	for j in $(grep typedef include/uapi/linux/dvb/frontend.h |cut -d' ' -f 3); do for i in $(find drivers/media -name '*.[ch]' -type f) $(find drivers/staging/media -name '*.[ch]' -type f); do sed "s,${j}_t,enum $j," <$i >a && mv a $i; done; done

While here, make CodingStyle fixes on the affected lines.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Stefan Richter <stefanr@s5r6.in-berlin.de> # for drivers/media/firewire/*

The only enum that was missing xrefs at frontend.h is fe_type.
Add xrefs for them.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Use a table for the delivery systems. The table is organized
by the type (cable, satellite, terrestrial) and shows what
standards are not fully implemented.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Instead of using a program listing, use a table and make clearer
what each define means.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

The table were documented at the legacy ioctl call. Move it
to the DVBv5 ioctl, and add a cross ref link on the legacy
section.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Putting it into a table allows to comment each possible
values, with makes more clear what field means.

Also, it allows to do cross-references with the frontend.h.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

Those data were retrieved by looking at A/153: ATSC Mobile DTV
Standard and guessing what makes more sense to each field.

Cc: Michael Ira Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

The ATSC M/H specific properties are not properly documented.
This became crearer when converting the existing data into
tables and adding cross references.

For now, just add placeholders, as a further investigation
about the meaning of each parameter is required.

Cc: Michael Ira Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

By cut-and-paste mistake, TRANSMISSION_MODE_AUTO were documented
twice, one at the wrong place.

Remove the wrong one.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

enum fe_bandwidth is documented at the frontend legacy xml
file.

Add xrefs for each entry there. This makes the hyperlinks at
frontend.h to go directly to the right documentation.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

The DTMB time interleaving was not properly documented. Add
a documentation for it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

There are lots of enums that are defined at dvbproperty.

Add xrefs for each entry there. This makes the hyperlinks at
frontend.h to go directly to the right documentation.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

enum fe_sec_voltage is documented together with FE_SET_VOLTAGE.

Add xrefs for each entry there. This makes the hyperlinks at
frontend.h to go directly to the right documentation.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

enum fe_sec_tone_mode is documented together with FE_SET_TONE.

Add xrefs for each entry there. This makes the hyperlinks at
frontend.h to go directly to the right documentation.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

enum fe_status is documented together with FE_READ_STATUS.

Add xrefs for each entry there. This makes the hyperlinks at
frontend.h to go directly to the right documentation.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>

enum fe_sec_mini_cmd is documented together with
FE_DISEQC_SEND_BURST.

Add xrefs for each entry there. This makes the hyperlinks at
frontend.h to go directly to the right documentation.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>