- 02 Oct, 2018 40 commits
-
-
Marek Szyprowski authored
BugLink: https://bugs.launchpad.net/bugs/1792377 [ Upstream commit ab337fc2 ] Set per-plane global alpha to maximum value to get proper blending of XRGB and ARGB planes. This fixes the strange order of overlapping planes. Signed-off-by:
Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by:
Inki Dae <inki.dae@samsung.com> Signed-off-by:
Sasha Levin <alexander.levin@microsoft.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
Stefan Bader <stefan.bader@canonical.com> Signed-off-by:
Kleber Sacilotto de Souza <kleber.souza@canonical.com>
-
Marek Szyprowski authored
BugLink: https://bugs.launchpad.net/bugs/1792377 [ Upstream commit dd209ef8 ] Fix following issues related to planar YUV pixel format configuration: - NV16/61 modes were incorrectly programmed as NV12/21, - YVU420 was programmed as YUV420 on source, - YVU420 and YUV422 were programmed as YUV420 on output. Signed-off-by:
-
BingJing Chang authored
BugLink: https://bugs.launchpad.net/bugs/1792377 [ Upstream commit bda31539 ] During assemble, the spare marked for replacement is not checked. conf->fullsync cannot be updated to be 1. As a result, recovery will treat it as a clean array. All recovering sectors are skipped. Original device is replaced with the not-recovered spare. mdadm -C /dev/md0 -l10 -n4 -pn2 /dev/loop[0123] mdadm /dev/md0 -a /dev/loop4 mdadm /dev/md0 --replace /dev/loop0 mdadm -S /dev/md0 # stop array during recovery mdadm -A /dev/md0 /dev/loop[01234] After reassemble, you can see recovery go on, but it completes immediately. In fact, recovery is not actually processed. To solve this problem, we just add the missing logics for replacment spares. (In raid1.c or raid5.c, they have already been checked.) Reported-by:
Alex Chen <alexchen@synology.com> Reviewed-by:
Alex Wu <alexwu@synology.com> Reviewed-by:
Chung-Chiang Cheng <cccheng@synology.com> Signed-off-by:
BingJing Chang <bingjingc@synology.com> Signed-off-by:
Shaohua Li <shli@fb.com> Signed-off-by:
-
Dan Carpenter authored
BugLink: https://bugs.launchpad.net/bugs/1792377 [ Upstream commit c4c2b764 ] The d->chans[] array has d->dma_requests elements so the > should be >= here. Fixes: 8e6152bc ("dmaengine: Add hisilicon k3 DMA engine driver") Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
Vinod Koul <vkoul@kernel.org> Signed-off-by:
-
Keerthy authored
BugLink: https://bugs.launchpad.net/bugs/1792377 [ Upstream commit 3eb1b955 ] The intc #interrupt-cells is equal to 1. Currently gpio node has 2 cells per IRQ which is wrong. Remove the additional cell for each of the interrupts. Signed-off-by:
Keerthy <j-keerthy@ti.com> Fixes: 2e38b946 ("ARM: davinci: da850: add GPIO DT node") Signed-off-by:
Sekhar Nori <nsekhar@ti.com> Signed-off-by:
-
Andy Lutomirski authored
BugLink: https://bugs.launchpad.net/bugs/1792377 [ Upstream commit ec348020 ] When I wrote the sigreturn test, I didn't realize that AMD's busted IRET behavior was different from Intel's busted IRET behavior: On AMD CPUs, the CPU leaks the high 32 bits of the kernel stack pointer to certain userspace contexts. Gee, thanks. There's very little the kernel can do about it. Modify the test so it passes. Signed-off-by:
Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/86e7fd3564497f657de30a36da4505799eebef01.1530076529.git.luto@kernel.orgSigned-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Sandipan Das authored
BugLink: https://bugs.launchpad.net/bugs/1792377 [ Upstream commit 143c99f6 ] For some cases, the callchain provided by the kernel may be empty. So, the callchain ip filtering code will cause a crash if we do not check whether the struct ip_callchain pointer is NULL before accessing any members. This can be observed on a powerpc64le system running Fedora 27 as shown below. # perf record -b -e cycles:u ls Before: # perf report --branch-history perf: Segmentation fault -------- backtrace -------- perf[0x1027615c] linux-vdso64.so.1(__kernel_sigtramp_rt64+0x0)[0x7fff856304d8] perf(arch_skip_callchain_idx+0x44)[0x10257c58] perf[0x1017f2e4] perf(thread__resolve_callchain+0x124)[0x1017ff5c] perf(sample__resolve_callchain+0xf0)[0x10172788] ... After: # perf report --branch-history Samples: 25 of event 'cycles:u', Event count (approx.): 2306870 Overhead Source:Line Symbol Shared Object + 11.60% _init+35736 [.] _init ls + 9.84% strcoll_l.c:137 [.] __strcoll_l libc-2.26.so + 9.16% memcpy.S:175 [.] __memcpy_power7 libc-2.26.so + 9.01% gconv_charset.h:54 [.] _nl_find_locale libc-2.26.so + 8.87% dl-addr.c:52 [.] _dl_addr libc-2.26.so + 8.83% _init+236 [.] _init ls ... Reported-by:
Ravi Bangoria <ravi.bangoria@linux.ibm.com> Signed-off-by:
Sandipan Das <sandipan@linux.ibm.com> Acked-by:
Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by:
-
Thomas Richter authored
BugLink: https://bugs.launchpad.net/bugs/1792377 [ Upstream commit b930e62e ] On s390 this test case fails because the socket identifiction numbers assigned to the CPU are higher than the CPU identification numbers. F/ix this by adding the platform architecture into the perf data header flag information. This helps identifiing the test platform and handles s390 specifics in process_cpu_topology(). Before: [root@p23lp27 perf]# perf test -vvvvv -F 39 39: Session topology : --- start --- templ file: /tmp/perf-test-iUv755 socket_id number is too big.You may need to upgrade the perf tool. ---- end ---- Session topology: Skip [root@p23lp27 perf]# After: [root@p23lp27 perf]# perf test -vvvvv -F 39 39: Session topology : --- start --- templ file: /tmp/perf-test-8X8VTs CPU 0, core 0, socket 6 CPU 1, core 1, socket 3 ---- end ---- Session topology: Ok [root@p23lp27 perf]# Signed-off-by:
Thomas Richter <tmricht@linux.ibm.com> Reviewed-by:
Hendrik Brueckner <brueckner@linux.ibm.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Fixes: c84974ed ("perf test: Add entry to test cpu topology") Link: http://lkml.kernel.org/r/20180611073153.15592-2-tmricht@linux.ibm.comSigned-off-by:
-
Ajay Gupta authored
BugLink: https://bugs.launchpad.net/bugs/1792377 [ Upstream commit 305886ca ] Some controllers take almost 55ms to complete controller restore state (CRS). There is no timeout limit mentioned in xhci specification so fixing the issue by increasing the timeout limit to 100ms [reformat code comment -Mathias] Signed-off-by:
Ajay Gupta <ajaykuee@gmail.com> Signed-off-by:
Nagaraj Annaiah <naga.annaiah@gmail.com> Signed-off-by:
Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by:
-
Daniel Mack authored
BugLink: https://bugs.launchpad.net/bugs/1792377 [ Upstream commit 49a6ec5b ] The touchscreen driver no longer configures the device as wakeup source by default. A "wakeup-source" property is needed. Signed-off-by:
Daniel Mack <daniel@zonque.org> Signed-off-by:
Tony Lindgren <tony@atomide.com> Signed-off-by:
-
Michael Trimarchi authored
BugLink: https://bugs.launchpad.net/bugs/1792377 [ Upstream commit 373c83a8 ] Using built-in in kernel image without a firmware in filesystem or in the kernel image can lead to a kernel NULL pointer deference. Watchdog need to be stopped in brcmf_sdio_remove The system is going down NOW! [ 1348.110759] Unable to handle kernel NULL pointer dereference at virtual address 000002f8 Sent SIGTERM to all processes [ 1348.121412] Mem abort info: [ 1348.126962] ESR = 0x96000004 [ 1348.130023] Exception class = DABT (current EL), IL = 32 bits [ 1348.135948] SET = 0, FnV = 0 [ 1348.138997] EA = 0, S1PTW = 0 [ 1348.142154] Data abort info: [ 1348.145045] ISV = 0, ISS = 0x00000004 [ 1348.148884] CM = 0, WnR = 0 [ 1348.151861] user pgtable: 4k pages, 48-bit VAs, pgdp = (____ptrval____) [ 1348.158475] [00000000000002f8] pgd=0000000000000000 [ 1348.163364] Internal error: Oops: 96000004 [#1] PREEMPT SMP [ 1348.168927] Modules linked in: ipv6 [ 1348.172421] CPU: 3 PID: 1421 Comm: brcmf_wdog/mmc0 Not tainted 4.17.0-rc5-next-20180517 #18 [ 1348.180757] Hardware name: Amarula A64-Relic (DT) [ 1348.185455] pstate: 60000005 (nZCv daif -PAN -UAO) [ 1348.190251] pc : brcmf_sdiod_freezer_count+0x0/0x20 [ 1348.195124] lr : brcmf_sdio_watchdog_thread+0x64/0x290 [ 1348.200253] sp : ffff00000b85be30 [ 1348.203561] x29: ffff00000b85be30 x28: 0000000000000000 [ 1348.208868] x27: ffff00000b6cb918 x26: ffff80003b990638 [ 1348.214176] x25: ffff0000087b1a20 x24: ffff80003b94f800 [ 1348.219483] x23: ffff000008e620c8 x22: ffff000008f0b660 [ 1348.224790] x21: ffff000008c6a858 x20: 00000000fffffe00 [ 1348.230097] x19: ffff80003b94f800 x18: 0000000000000001 [ 1348.235404] x17: 0000ffffab2e8a74 x16: ffff0000080d7de8 [ 1348.240711] x15: 0000000000000000 x14: 0000000000000400 [ 1348.246018] x13: 0000000000000400 x12: 0000000000000001 [ 1348.251324] x11: 00000000000002c4 x10: 0000000000000a10 [ 1348.256631] x9 : ffff00000b85bc40 x8 : ffff80003be11870 [ 1348.261937] x7 : ffff80003dfc7308 x6 : 000000078ff08b55 [ 1348.267243] x5 : 00000139e1058400 x4 : 0000000000000000 [ 1348.272550] x3 : dead000000000100 x2 : 958f2788d6618100 [ 1348.277856] x1 : 00000000fffffe00 x0 : 0000000000000000 Signed-off-by:
Michael Trimarchi <michael@amarulasolutions.com> Acked-by:
Arend van Spriel <arend.vanspriel@broadcom.com> Tested-by:
Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org> Signed-off-by:
-
Ganesh Goudar authored
BugLink: https://bugs.launchpad.net/bugs/1792377 [ Upstream commit 5ce36338 ] When we are disabling DCB, store "0" in txq->dcb_prio since that's used for future TX Work Request "OVLAN_IDX" values. Setting non zero priority upon disabling DCB would halt the traffic. Reported-by:
AMG Zollner Robert <robert@cloudmedia.eu> CC: David Ahern <dsa@cumulusnetworks.com> Signed-off-by:
Casey Leedom <leedom@chelsio.com> Signed-off-by:
Ganesh Goudar <ganeshgr@chelsio.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Casey Schaufler authored
BugLink: https://bugs.launchpad.net/bugs/1792377 [ Upstream commit 7b4e8843 ] Smack: Mark inode instant in smack_task_to_inode /proc clean-up in commit 1bbc5513 resulted in smack_task_to_inode() being called before smack_d_instantiate. This resulted in the smk_inode value being ignored, even while present for files in /proc/self. Marking the inode as instant here fixes that. Signed-off-by:
Casey Schaufler <casey@schaufler-ca.com> Signed-off-by:
James Morris <james.morris@microsoft.com> Signed-off-by:
-
Hangbin Liu authored
BugLink: https://bugs.launchpad.net/bugs/1792377 [ Upstream commit 6c6da928 ] After recieving MLD querys, we update idev->mc_maxdelay with max_delay from query header. This make the later unsolicited reports have the same interval with mc_maxdelay, which means we may send unsolicited reports with long interval time instead of default configured interval time. Also as we will not call ipv6_mc_reset() after device up. This issue will be there even after leave the group and join other groups. Fixes: fc4eba58 ("ipv6: make unsolicited report intervals configurable for mld") Signed-off-by:
Hangbin Liu <liuhangbin@gmail.com> Signed-off-by:
-
Steven Rostedt (VMware) authored
BugLink: https://bugs.launchpad.net/bugs/1792377 [ Upstream commit fcc784be ] While debugging where things were going wrong with mapping enabling/disabling interrupts with the lockdep state and actual real enabling and disabling interrupts, I had to silent the IRQ disabling/enabling in debug_check_no_locks_freed() because it was always showing up as it was called before the splat was. Use raw_local_irq_save/restore() for not only debug_check_no_locks_freed() but for all internal lockdep functions, as they hide useful information about where interrupts were used incorrectly last. Signed-off-by:
Steven Rostedt (VMware) <rostedt@goodmis.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Will Deacon <will.deacon@arm.com> Link: https://lkml.kernel.org/lkml/20180404140630.3f4f4c7a@gandalf.local.homeSigned-off-by:
-
Bartosz Golaszewski authored
BugLink: https://bugs.launchpad.net/bugs/1792377 [ Upstream commit ea0820bb ] Device tree based systems without of_dev_auxdata will have the mdio device named differently than "davinci_mdio(.0)". In this case use the device's parent's compatible string for matching Signed-off-by:
Bartosz Golaszewski <bgolaszewski@baylibre.com> Signed-off-by:
-
Alexey Brodkin authored
BugLink: https://bugs.launchpad.net/bugs/1792377 [ Upstream commit 2f24ef74 ] machine_desc->init_per_cpu() hook is supposed to be per cpu initialization and would seem to apply equally to UP and/or SMP. Infact the comment in header file seems to suggest it works for UP too, which was not the case and this patch. This enables !CONFIG_SMP build for platforms such as hsdk. Signed-off-by:
Alexey Brodkin <abrodkin@synopsys.com> Signed-off-by:
Vineet Gupta <vgupta@synopsys.com> [vgupta: trimmeed changelog] Signed-off-by:
-
Li RongQing authored
BugLink: https://bugs.launchpad.net/bugs/1792377 [ Upstream commit 7892bd08 ] if dev_get_valid_name failed, propagate its return code and remove the setting err to ENODEV, it will be set to 0 again before dev_change_net_namespace exits. Signed-off-by:
Li RongQing <lirongqing@baidu.com> Signed-off-by:
-
Stefan Agner authored
BugLink: https://bugs.launchpad.net/bugs/1792377 [ Upstream commit 4e8439aa ] The array bpq_eth_addr is only used to get the size of an address, whereas the bcast_addr is used to set the broadcast address. This leads to a warning when using clang: drivers/net/hamradio/bpqether.c:94:13: warning: variable 'bpq_eth_addr' is not needed and will not be emitted [-Wunneeded-internal-declaration] static char bpq_eth_addr[6]; ^ Remove both variables and use the common eth_broadcast_addr to set the broadcast address. Signed-off-by:
Stefan Agner <stefan@agner.ch> Signed-off-by:
-
Govindarajulu Varadarajan authored
BugLink: https://bugs.launchpad.net/bugs/1792377 [ Upstream commit 3256d29f ] lockdep spotted that we are using rfs_h.lock in enic_get_rxnfc() without initializing. rfs_h.lock is initialized in enic_open(). But ethtool_ops can be called when interface is down. Move enic_rfs_flw_tbl_init to enic_probe. INFO: trying to register non-static key. the code is fine but needs lockdep annotation. turning off the locking correctness validator. CPU: 18 PID: 1189 Comm: ethtool Not tainted 4.17.0-rc7-devel+ #27 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.11.0-20171110_100015-anatol 04/01/2014 Call Trace: dump_stack+0x85/0xc0 register_lock_class+0x550/0x560 ? __handle_mm_fault+0xa8b/0x1100 __lock_acquire+0x81/0x670 lock_acquire+0xb9/0x1e0 ? enic_get_rxnfc+0x139/0x2b0 [enic] _raw_spin_lock_bh+0x38/0x80 ? enic_get_rxnfc+0x139/0x2b0 [enic] enic_get_rxnfc+0x139/0x2b0 [enic] ethtool_get_rxnfc+0x8d/0x1c0 dev_ethtool+0x16c8/0x2400 ? __mutex_lock+0x64d/0xa00 ? dev_load+0x6a/0x150 dev_ioctl+0x253/0x4b0 sock_do_ioctl+0x9a/0x130 sock_ioctl+0x1af/0x350 do_vfs_ioctl+0x8e/0x670 ? syscall_trace_enter+0x1e2/0x380 ksys_ioctl+0x60/0x90 __x64_sys_ioctl+0x16/0x20 do_syscall_64+0x5a/0x170 entry_SYSCALL_64_after_hwframe+0x49/0xbe Signed-off-by:
Govindarajulu Varadarajan <gvaradar@cisco.com> Signed-off-by:
-
Sudarsana Reddy Kalluru authored
BugLink: https://bugs.launchpad.net/bugs/1792377 [ Upstream commit 3935a709 ] Avoid calling a SIMD fastpath handler if it is NULL. The check is needed to handle an unlikely scenario where unsolicited interrupt is destined to a PF in INTa mode. Fixes: fe56b9e6 ("qed: Add module with basic common support") Signed-off-by:
Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com> Signed-off-by:
Ariel Elior <ariel.elior@cavium.com> Signed-off-by:
Michal Kalderon <Michal.Kalderon@cavium.com> Signed-off-by:
-
Zhizhou Zhang authored
BugLink: https://bugs.launchpad.net/bugs/1792377 [ Upstream commit b154886f ] We can't call function trace hook before setup percpu offset. When entering secondary_start_kernel(), percpu offset has not been initialized. So this lead hotplug malfunction. Here is the flow to reproduce this bug: echo 0 > /sys/devices/system/cpu/cpu1/online echo function > /sys/kernel/debug/tracing/current_tracer echo 1 > /sys/kernel/debug/tracing/tracing_on echo 1 > /sys/devices/system/cpu/cpu1/online Acked-by:
Mark Rutland <mark.rutland@arm.com> Tested-by:
Suzuki K Poulose <suzuki.poulose@arm.com> Signed-off-by:
Zhizhou Zhang <zhizhouzhang@asrmicro.com> Signed-off-by:
Catalin Marinas <catalin.marinas@arm.com> Signed-off-by:
-
Zhouyang Jia authored
BugLink: https://bugs.launchpad.net/bugs/1792377 [ Upstream commit 93efbd39 ] When xenbus_printf fails, the lack of error-handling code may cause unexpected results. This patch adds error-handling code after calling xenbus_printf. Signed-off-by:
Zhouyang Jia <jiazhouyang09@gmail.com> Reviewed-by:
Juergen Gross <jgross@suse.com> Signed-off-by:
-
Grigor Tovmasyan authored
BugLink: https://bugs.launchpad.net/bugs/1792377 [ Upstream commit 9bb073a0 ] Freed allocated request for ep0 to prevent memory leak in case when dwc2_driver_probe() failed. Cc: Stefan Wahren <stefan.wahren@i2se.com> Cc: Marek Szyprowski <m.szyprowski@samsung.com> Tested-by:
Stefan Wahren <stefan.wahren@i2se.com> Tested-by:
Minas Harutyunyan <hminas@synopsys.com> Signed-off-by:
Grigor Tovmasyan <tovmasya@synopsys.com> Signed-off-by:
Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by:
-
Chunfeng Yun authored
BugLink: https://bugs.launchpad.net/bugs/1792377 [ Upstream commit 980900d6 ] It happens when enable debug log, if set_alt() returns USB_GADGET_DELAYED_STATUS and usb_composite_setup_continue() is called before increasing count of @delayed_status, so fix it by using spinlock of @cdev->lock. Signed-off-by:
Chunfeng Yun <chunfeng.yun@mediatek.com> Tested-by:
Jay Hsu <shih-chieh.hsu@mediatek.com> Signed-off-by:
-
William Wu authored
BugLink: https://bugs.launchpad.net/bugs/1792377 [ Upstream commit 70c3c8cb ] If isoc split in transfer with no data (the length of DATA0 packet is zero), we can't simply return immediately. Because the DATA0 can be the first transaction or the second transaction for the isoc split in transaction. If the DATA0 packet with no data is in the first transaction, we can return immediately. But if the DATA0 packet with no data is in the second transaction of isoc split in transaction sequence, we need to increase the qtd->isoc_frame_index and giveback urb to device driver if needed, otherwise, the MDATA packet will be lost. A typical test case is that connect the dwc2 controller with an usb hs Hub (GL852G-12), and plug an usb fs audio device (Plantronics headset) into the downstream port of Hub. Then use the usb mic to record, we can find noise when playback. In the case, the isoc split in transaction sequence like this: - SSPLIT IN transaction - CSPLIT IN transaction - MDATA packet (176 bytes) - CSPLIT IN transaction - DATA0 packet (0 byte) This patch use both the length of DATA0 and qtd->isoc_split_offset to check if the DATA0 is in the second transaction. Tested-by:
Gevorg Sahakyan <sahakyan@synopsys.com> Tested-by:
Heiko Stuebner <heiko@sntech.de> Acked-by: Minas Harutyunyan hminas@synopsys.com> Signed-off-by:
William Wu <william.wu@rock-chips.com> Signed-off-by:
-
Ray Jui authored
BugLink: https://bugs.launchpad.net/bugs/1792377 [ Upstream commit 71ca3409 ] Fix I2C controller interrupt to use IRQ_TYPE_LEVEL_HIGH for Broadcom Cygnus SoC. Fixes: b51c05a3 ("ARM: dts: add I2C device nodes for Broadcom Cygnus") Signed-off-by:
Ray Jui <ray.jui@broadcom.com> Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
Fathi Boudra authored
BugLink: https://bugs.launchpad.net/bugs/1792377 [ Upstream commit d6a3e551 ] Unless the software synchronization objects (CONFIG_SW_SYNC) is enabled, the sync test will be skipped: TAP version 13 1..0 # Skipped: Sync framework not supported by kernel Add a config fragment file to be able to run "make kselftest-merge" to enable relevant configuration required in order to run the sync test. Signed-off-by:
Fathi Boudra <fathi.boudra@linaro.org> Link: https://lkml.org/lkml/2017/5/5/14Signed-off-by:
Anders Roxell <anders.roxell@linaro.org> Signed-off-by:
Shuah Khan (Samsung OSG) <shuah@kernel.org> Signed-off-by:
-
Shuah Khan (Samsung OSG) authored
BugLink: https://bugs.launchpad.net/bugs/1792377 [ Upstream commit 68581446 ] When zram test is skipped because of unmet dependencies and/or unsupported configuration, it exits with error which is treated as a fail by the Kselftest framework. This leads to false negative result even when the test could not be run. Change it to return kselftest skip code when a test gets skipped to clearly report that the test could not be run. Kselftest framework SKIP code is 4 and the framework prints appropriate messages to indicate that the test is skipped. Signed-off-by:
-
Shuah Khan (Samsung OSG) authored
BugLink: https://bugs.launchpad.net/bugs/1792377 [ Upstream commit d7d5311d ] When user test is skipped because of unmet dependencies and/or unsupported configuration, it exits with error which is treated as a fail by the Kselftest framework. This leads to false negative result even when the test could not be run. Change it to return kselftest skip code when a test gets skipped to clearly report that the test could not be run. Add an explicit check for module presence and return skip code if module isn't present. Kselftest framework SKIP code is 4 and the framework prints appropriate messages to indicate that the test is skipped. Signed-off-by:
-
Shuah Khan (Samsung OSG) authored
BugLink: https://bugs.launchpad.net/bugs/1792377 [ Upstream commit 87815780 ] When static_keys test is skipped because of unmet dependencies and/or unsupported configuration, it exits with error which is treated as a fail by the Kselftest framework. This leads to false negative result even when the test could not be run. Change it to return kselftest skip code when a test gets skipped to clearly report that the test could not be run. Added an explicit searches for test_static_key_base and test_static_keys modules and return skip code if they aren't found to differentiate between the failure to load the module condition and module not found condition. Kselftest framework SKIP code is 4 and the framework prints appropriate messages to indicate that the test is skipped. Signed-off-by:
-
Shuah Khan (Samsung OSG) authored
BugLink: https://bugs.launchpad.net/bugs/1792377 [ Upstream commit 856e7c4b ] When pstore_post_reboot test gets skipped because of unmet dependencies and/or unsupported configuration, it returns 0 which is treated as a pass by the Kselftest framework. This leads to false positive result even when the test could not be run. Change it to return kselftest skip code when a test gets skipped to clearly report that the test could not be run. Kselftest framework SKIP code is 4 and the framework prints appropriate messages to indicate that the test is skipped. Signed-off-by:
Kees Cook <keescook@chromium.org> Signed-off-by:
-
Eric Dumazet authored
BugLink: https://bugs.launchpad.net/bugs/1792377 [ Upstream commit 9ce7bc03 ] It is a waste of memory to use a full "struct netns_sysctl_ipv6" while only one pointer is really used, considering netns_sysctl_ipv6 keeps growing. Also, since "struct netns_frags" has cache line alignment, it is better to move the frags_hdr pointer outside, otherwise we spend a full cache line for this pointer. This saves 192 bytes of memory per netns. Fixes: c038a767 ("ipv6: add a new namespace for nf_conntrack_reasm") Signed-off-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by:
-
Alexey Brodkin authored
BugLink: https://bugs.launchpad.net/bugs/1792377 [ Upstream commit 74c11e30 ] GCC built for arc*-*-linux has "-mmedium-calls" implicitly enabled by default thus we don't see any problems during Linux kernel compilation. ----------------------------->8------------------------ arc-linux-gcc -mcpu=arc700 -Q --help=target | grep calls -mlong-calls [disabled] -mmedium-calls [enabled] ----------------------------->8------------------------ But if we try to use so-called Elf32 toolchain with GCC configured for arc*-*-elf* then we'd see the following failure: ----------------------------->8------------------------ init/do_mounts.o: In function 'init_rootfs': do_mounts.c:(.init.text+0x108): relocation truncated to fit: R_ARC_S21W_PCREL against symbol 'unregister_filesystem' defined in .text section in fs/filesystems.o arc-elf32-ld: final link failed: Symbol needs debug section which does not exist make: *** [vmlinux] Error 1 ----------------------------->8------------------------ That happens because neither "-mmedium-calls" nor "-mlong-calls" are enabled in Elf32 GCC: ----------------------------->8------------------------ arc-elf32-gcc -mcpu=arc700 -Q --help=target | grep calls -mlong-calls [disabled] -mmedium-calls [disabled] ----------------------------->8------------------------ Now to make it possible to use Elf32 toolchain for building Linux kernel we're explicitly add "-mmedium-calls" to CFLAGS. And since we add "-mmedium-calls" to the global CFLAGS there's no point in having per-file copies thus removing them. Signed-off-by:
-
Greg Kroah-Hartman authored
BugLink: https://bugs.launchpad.net/bugs/1792340Signed-off-by:
-
Kees Cook authored
BugLink: https://bugs.launchpad.net/bugs/1792340 [ Upstream commit 5e22002a ] It was possible to directly leak the kernel address where the isdn_dev structure pointer was stored. This is a kernel ASLR bypass for anyone with access to the ioctl. The code had been present since the beginning of git history, though this shouldn't ever be needed for normal operation, therefore remove it. Reported-by:
Al Viro <viro@zeniv.linux.org.uk> Cc: Karsten Keil <isdn@linux-pingi.de> Signed-off-by:
-
Sudip Mukherjee authored
BugLink: https://bugs.launchpad.net/bugs/1792340 commit 4e1a720d upstream. slub debug reported: [ 440.648642] ============================================================================= [ 440.648649] BUG kmalloc-1024 (Tainted: G BU O ): Poison overwritten [ 440.648651] ----------------------------------------------------------------------------- [ 440.648655] INFO: 0xe70f4bec-0xe70f4bec. First byte 0x6a instead of 0x6b [ 440.648665] INFO: Allocated in sk_prot_alloc+0x6b/0xc6 age=33155 cpu=1 pid=1047 [ 440.648671] ___slab_alloc.constprop.24+0x1fc/0x292 [ 440.648675] __slab_alloc.isra.18.constprop.23+0x1c/0x25 [ 440.648677] __kmalloc+0xb6/0x17f [ 440.648680] sk_prot_alloc+0x6b/0xc6 [ 440.648683] sk_alloc+0x1e/0xa1 [ 440.648700] sco_sock_alloc.constprop.6+0x26/0xaf [bluetooth] [ 440.648716] sco_connect_cfm+0x166/0x281 [bluetooth] [ 440.648731] hci_conn_request_evt.isra.53+0x258/0x281 [bluetooth] [ 440.648746] hci_event_packet+0x28b/0x2326 [bluetooth] [ 440.648759] hci_rx_work+0x161/0x291 [bluetooth] [ 440.648764] process_one_work+0x163/0x2b2 [ 440.648767] worker_thread+0x1a9/0x25c [ 440.648770] kthread+0xf8/0xfd [ 440.648774] ret_from_fork+0x2e/0x38 [ 440.648779] INFO: Freed in __sk_destruct+0xd3/0xdf age=3815 cpu=1 pid=1047 [ 440.648782] __slab_free+0x4b/0x27a [ 440.648784] kfree+0x12e/0x155 [ 440.648787] __sk_destruct+0xd3/0xdf [ 440.648790] sk_destruct+0x27/0x29 [ 440.648793] __sk_free+0x75/0x91 [ 440.648795] sk_free+0x1c/0x1e [ 440.648810] sco_sock_kill+0x5a/0x5f [bluetooth] [ 440.648825] sco_conn_del+0x8e/0xba [bluetooth] [ 440.648840] sco_disconn_cfm+0x3a/0x41 [bluetooth] [ 440.648855] hci_event_packet+0x45e/0x2326 [bluetooth] [ 440.648868] hci_rx_work+0x161/0x291 [bluetooth] [ 440.648872] process_one_work+0x163/0x2b2 [ 440.648875] worker_thread+0x1a9/0x25c [ 440.648877] kthread+0xf8/0xfd [ 440.648880] ret_from_fork+0x2e/0x38 [ 440.648884] INFO: Slab 0xf4718580 objects=27 used=27 fp=0x (null) flags=0x40008100 [ 440.648886] INFO: Object 0xe70f4b88 @offset=19336 fp=0xe70f54f8 When KASAN was enabled, it reported: [ 210.096613] ================================================================== [ 210.096634] BUG: KASAN: use-after-free in ex_handler_refcount+0x5b/0x127 [ 210.096641] Write of size 4 at addr ffff880107e17160 by task kworker/u9:1/2040 [ 210.096651] CPU: 1 PID: 2040 Comm: kworker/u9:1 Tainted: G U O 4.14.47-20180606+ #2 [ 210.096654] Hardware name: , BIOS 2017.01-00087-g43e04de 08/30/2017 [ 210.096693] Workqueue: hci0 hci_rx_work [bluetooth] [ 210.096698] Call Trace: [ 210.096711] dump_stack+0x46/0x59 [ 210.096722] print_address_description+0x6b/0x23b [ 210.096729] ? ex_handler_refcount+0x5b/0x127 [ 210.096736] kasan_report+0x220/0x246 [ 210.096744] ex_handler_refcount+0x5b/0x127 [ 210.096751] ? ex_handler_clear_fs+0x85/0x85 [ 210.096757] fixup_exception+0x8c/0x96 [ 210.096766] do_trap+0x66/0x2c1 [ 210.096773] do_error_trap+0x152/0x180 [ 210.096781] ? fixup_bug+0x78/0x78 [ 210.096817] ? hci_debugfs_create_conn+0x244/0x26a [bluetooth] [ 210.096824] ? __schedule+0x113b/0x1453 [ 210.096830] ? sysctl_net_exit+0xe/0xe [ 210.096837] ? __wake_up_common+0x343/0x343 [ 210.096843] ? insert_work+0x107/0x163 [ 210.096850] invalid_op+0x1b/0x40 [ 210.096888] RIP: 0010:hci_debugfs_create_conn+0x244/0x26a [bluetooth] [ 210.096892] RSP: 0018:ffff880094a0f970 EFLAGS: 00010296 [ 210.096898] RAX: 0000000000000000 RBX: ffff880107e170e8 RCX: ffff880107e17160 [ 210.096902] RDX: 000000000000002f RSI: ffff88013b80ed40 RDI: ffffffffa058b940 [ 210.096906] RBP: ffff88011b2b0578 R08: 00000000852f0ec9 R09: ffffffff81cfcf9b [ 210.096909] R10: 00000000d21bdad7 R11: 0000000000000001 R12: ffff8800967b0488 [ 210.096913] R13: ffff880107e17168 R14: 0000000000000068 R15: ffff8800949c0008 [ 210.096920] ? __sk_destruct+0x2c6/0x2d4 [ 210.096959] hci_event_packet+0xff5/0x7de2 [bluetooth] [ 210.096969] ? __local_bh_enable_ip+0x43/0x5b [ 210.097004] ? l2cap_sock_recv_cb+0x158/0x166 [bluetooth] [ 210.097039] ? hci_le_meta_evt+0x2bb3/0x2bb3 [bluetooth] [ 210.097075] ? l2cap_ertm_init+0x94e/0x94e [bluetooth] [ 210.097093] ? xhci_urb_enqueue+0xbd8/0xcf5 [xhci_hcd] [ 210.097102] ? __accumulate_pelt_segments+0x24/0x33 [ 210.097109] ? __accumulate_pelt_segments+0x24/0x33 [ 210.097115] ? __update_load_avg_se.isra.2+0x217/0x3a4 [ 210.097122] ? set_next_entity+0x7c3/0x12cd [ 210.097128] ? pick_next_entity+0x25e/0x26c [ 210.097135] ? pick_next_task_fair+0x2ca/0xc1a [ 210.097141] ? switch_mm_irqs_off+0x346/0xb4f [ 210.097147] ? __switch_to+0x769/0xbc4 [ 210.097153] ? compat_start_thread+0x66/0x66 [ 210.097188] ? hci_conn_check_link_mode+0x1cd/0x1cd [bluetooth] [ 210.097195] ? finish_task_switch+0x392/0x431 [ 210.097228] ? hci_rx_work+0x154/0x487 [bluetooth] [ 210.097260] hci_rx_work+0x154/0x487 [bluetooth] [ 210.097269] process_one_work+0x579/0x9e9 [ 210.097277] worker_thread+0x68f/0x804 [ 210.097285] kthread+0x31c/0x32b [ 210.097292] ? rescuer_thread+0x70c/0x70c [ 210.097299] ? kthread_create_on_node+0xa3/0xa3 [ 210.097306] ret_from_fork+0x35/0x40 [ 210.097314] Allocated by task 2040: [ 210.097323] kasan_kmalloc.part.1+0x51/0xc7 [ 210.097328] __kmalloc+0x17f/0x1b6 [ 210.097335] sk_prot_alloc+0xf2/0x1a3 [ 210.097340] sk_alloc+0x22/0x297 [ 210.097375] sco_sock_alloc.constprop.7+0x23/0x202 [bluetooth] [ 210.097410] sco_connect_cfm+0x2d0/0x566 [bluetooth] [ 210.097443] hci_conn_request_evt.isra.53+0x6d3/0x762 [bluetooth] [ 210.097476] hci_event_packet+0x85e/0x7de2 [bluetooth] [ 210.097507] hci_rx_work+0x154/0x487 [bluetooth] [ 210.097512] process_one_work+0x579/0x9e9 [ 210.097517] worker_thread+0x68f/0x804 [ 210.097523] kthread+0x31c/0x32b [ 210.097529] ret_from_fork+0x35/0x40 [ 210.097533] Freed by task 2040: [ 210.097539] kasan_slab_free+0xb3/0x15e [ 210.097544] kfree+0x103/0x1a9 [ 210.097549] __sk_destruct+0x2c6/0x2d4 [ 210.097584] sco_conn_del.isra.1+0xba/0x10e [bluetooth] [ 210.097617] hci_event_packet+0xff5/0x7de2 [bluetooth] [ 210.097648] hci_rx_work+0x154/0x487 [bluetooth] [ 210.097653] process_one_work+0x579/0x9e9 [ 210.097658] worker_thread+0x68f/0x804 [ 210.097663] kthread+0x31c/0x32b [ 210.097670] ret_from_fork+0x35/0x40 [ 210.097676] The buggy address belongs to the object at ffff880107e170e8 which belongs to the cache kmalloc-1024 of size 1024 [ 210.097681] The buggy address is located 120 bytes inside of 1024-byte region [ffff880107e170e8, ffff880107e174e8) [ 210.097683] The buggy address belongs to the page: [ 210.097689] page:ffffea00041f8400 count:1 mapcount:0 mapping: (null) index:0xffff880107e15b68 compound_mapcount: 0 [ 210.110194] flags: 0x8000000000008100(slab|head) [ 210.115441] raw: 8000000000008100 0000000000000000 ffff880107e15b68 0000000100170016 [ 210.115448] raw: ffffea0004a47620 ffffea0004b48e20 ffff88013b80ed40 0000000000000000 [ 210.115451] page dumped because: kasan: bad access detected [ 210.115454] Memory state around the buggy address: [ 210.115460] ffff880107e17000: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc [ 210.115465] ffff880107e17080: fc fc fc fc fc fc fc fc fc fc fc fc fc fb fb fb [ 210.115469] >ffff880107e17100: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb [ 210.115472] ^ [ 210.115477] ffff880107e17180: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb [ 210.115481] ffff880107e17200: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb [ 210.115483] ================================================================== And finally when BT_DBG() and ftrace was enabled it showed: <...>-14979 [001] .... 186.104191: sco_sock_kill <-sco_sock_close <...>-14979 [001] .... 186.104191: sco_sock_kill <-sco_sock_release <...>-14979 [001] .... 186.104192: sco_sock_kill: sk ef0497a0 state 9 <...>-14979 [001] .... 186.104193: bt_sock_unlink <-sco_sock_kill kworker/u9:2-792 [001] .... 186.104246: sco_sock_kill <-sco_conn_del kworker/u9:2-792 [001] .... 186.104248: sco_sock_kill: sk ef0497a0 state 9 kworker/u9:2-792 [001] .... 186.104249: bt_sock_unlink <-sco_sock_kill kworker/u9:2-792 [001] .... 186.104250: sco_sock_destruct <-__sk_destruct kworker/u9:2-792 [001] .... 186.104250: sco_sock_destruct: sk ef0497a0 kworker/u9:2-792 [001] .... 186.104860: hci_conn_del <-hci_event_packet kworker/u9:2-792 [001] .... 186.104864: hci_conn_del: hci0 hcon ef0484c0 handle 266 Only in the failed case, sco_sock_kill() gets called with the same sock pointer two times. Add a check for SOCK_DEAD to avoid continue killing a socket which has already been killed. Signed-off-by:
Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by:
Marcel Holtmann <marcel@holtmann.org> Signed-off-by:
-
Chen Hu authored
BugLink: https://bugs.launchpad.net/bugs/1792340 commit dfcab6ba upstream. dw8250_set_termios() doesn't set baud rate if the arg "old ktermios" is NULL. This happens during resume. Call Trace: ... [ 54.928108] dw8250_set_termios+0x162/0x170 [ 54.928114] serial8250_set_termios+0x17/0x20 [ 54.928117] uart_change_speed+0x64/0x160 [ 54.928119] uart_resume_port ... So the baud rate is not restored after S3 and breaks the apps who use UART, for example, console and bluetooth etc. We address this issue by setting the baud rate irrespective of arg "old", just like the drivers for other 8250 IPs. This is tested with Intel Broxton platform. Signed-off-by:
Chen Hu <hu1.chen@intel.com> Fixes: 4e26b134 ("serial: 8250_dw: clock rate handling for all ACPI platforms") Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com> Cc: stable <stable@vger.kernel.org> Reviewed-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by:
-
Willy Tarreau authored
BugLink: https://bugs.launchpad.net/bugs/1792340 commit 231f9415 upstream. Every time I tried to upgrade my laptop from 3.10.x to 4.x I faced an issue by which the fan would run at full speed upon resume. Bisecting it showed me the issue was introduced in 3.17 by commit 821d6f03 (ACPI / sleep: Do not save NVS for new machines to accelerate S3). This code only affects machines built starting as of 2012, but this Asus 1025C laptop was made in 2012 and apparently needs the NVS data to be saved, otherwise the CPU's thermal state is not properly reported on resume and the fan runs at full speed upon resume. Here's a very simple way to check if such a machine is affected : # cat /sys/class/thermal/thermal_zone0/temp 55000 ( now suspend, wait one second and resume ) # cat /sys/class/thermal/thermal_zone0/temp 0 (and after ~15 seconds the fan starts to spin) Let's apply the same quirk as commit cbc00c13 (ACPI: save NVS memory for Lenovo G50-45) and reuse the function it provides. Note that this commit was already backported to 4.9.x but not 4.4.x. Cc: 3.17+ <stable@vger.kernel.org> # 3.17+: requires cbc00c13Signed-off-by:
Willy Tarreau <w@1wt.eu> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Zhang Rui authored
BugLink: https://bugs.launchpad.net/bugs/1792340 commit cbc00c13 upstream. In commit 821d6f03 (ACPI / sleep: Do not save NVS for new machines to accelerate S3), to optimize S3 suspend/resume speed, code is introduced to ignore NVS memory saving during S3 for all the platforms later than 2012. But, Lenovo G50-45, a platform released in 2015, still needs NVS memory saving during S3. A quirk is introduced for this platform. Link: https://bugzilla.kernel.org/show_bug.cgi?id=189431Tested-by:
Przemek <soprwa@gmail.com> Signed-off-by:
Zhang Rui <rui.zhang@intel.com> [ rjw: Drop unnecessary code ] Signed-off-by:
-
