Command Queuing was enabled completely for J721e controllers which lead
to partial enablement even for Am65x. Complete CQ implementation for
AM65x by adding the irq callback.

Fixes: f545702b ("mmc: sdhci_am654: Add Support for Command Queuing Engine to J721E")
Cc: stable@vger.kernel.org
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200108143301.1929-4-faiz_abbas@ti.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The tuning data is leftover in the buffer after tuning. This can cause
issues in future data commands, especially with CQHCI. Reset the command
and data lines after tuning to continue from a clean state.

Fixes: 41fd4cae ("mmc: sdhci_am654: Add Initial Support for AM654 SDHCI driver")
Cc: stable@vger.kernel.org
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200108143301.1929-3-faiz_abbas@ti.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The MMC/SD controllers on am65x and j721e don't in fact detect the write
protect line as inverted. No issues were detected because of this
because the sdwp line is not connected on any of the evms. Fix this by
removing the flag.

Fixes: 1accbced ("mmc: sdhci_am654: Add Support for 4 bit IP on J721E")
Cc: stable@vger.kernel.org
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200108143301.1929-2-faiz_abbas@ti.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

This patch is to fix clock setting code for different controller
versions. Two of HW changes after vendor version 2.2 are removing
PEREN/HCKEN/IPGEN bits in system control register, and adding SD
clock stable bit in present state register. This patch cleans up
related code too.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Link: https://lore.kernel.org/r/20200108040713.38888-2-yangbo.lu@nxp.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

This patch is to fix operating in esdhc_reset() for different
controller versions, and to add bus-width restoring after data
reset for eSDHC (verdor version <= 2.2).

Also add annotation for understanding.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20200108040713.38888-1-yangbo.lu@nxp.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

There is an official update for eSDHC tuning erratum A-008171.
This patch is to implement the changes,
- Affect all revisions of SoC.
- Changes for tuning window checking.
- Hardware hits a new condition that tuning succeeds although
  the eSDHC might not have tuned properly for type2 SoCs
  (soc_tuning_erratum_type2[] array in driver). So check
  tuning window after tuning succeeds.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20191212075219.48625-2-yangbo.lu@nxp.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Convert to use a new function esdhc_tuning_window_ptr() to
get tuning window start point and end point.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20191212075219.48625-1-yangbo.lu@nxp.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.

By using dma_request_chan() directly the driver can support deferred
probing against DMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/20191217122254.7103-1-peter.ujfalusi@ti.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.

By using dma_request_chan() directly the driver can support deferred
probing against DMA if needed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191217113114.32085-1-peter.ujfalusi@ti.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.

By using dma_request_chan() directly the driver can support deferred
probing against DMA if needed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191217113031.31847-1-peter.ujfalusi@ti.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.

By using dma_request_chan() directly the driver can support deferred
probing against DMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191217113004.31688-1-peter.ujfalusi@ti.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.

By using dma_request_chan() directly the driver can support deferred
probing against DMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191217112934.31535-1-peter.ujfalusi@ti.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.

By using dma_request_chan() directly the driver can support deferred
probing against DMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191217112847.31351-1-peter.ujfalusi@ti.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.

By using dma_request_chan() directly the driver can support deferred
probing against DMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191217112803.31161-1-peter.ujfalusi@ti.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.

By using dma_request_chan() directly the driver can support deferred
probing against DMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191217112737.31024-1-peter.ujfalusi@ti.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

dma_request_slave_channel() is a wrapper on top of dma_request_chan()
eating up the error code.

By using dma_request_chan() directly the driver can support deferred
probing against DMA.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20191217112656.30860-1-peter.ujfalusi@ti.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The erratum A-009204 workaround patch was reverted because of
incorrect implementation.

8b6dc6b2 mmc: sdhci-of-esdhc: Revert "mmc: sdhci-of-esdhc: add
        erratum A-009204 support"

This patch is to re-implement the workaround (add a 5 ms delay
before setting SYSCTL[RSTD] to make sure all the DMA transfers
are finished).
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Link: https://lore.kernel.org/r/20191219032335.26528-1-yangbo.lu@nxp.com
Fixes: 5dd19552 ("mmc: sdhci-of-esdhc: add erratum A-009204 support")
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

For the ux500v2 variant of the PL18x block, any block sizes
are supported. This is necessary to support some SDIO
transfers. This also affects the QCOM MMCI variant and the
ST micro variant.

For Ux500 an additional quirk only allowing DMA on blocks
that are a power of two is needed. This might be a bug in
the DMA engine (DMA40) or the MMCI or in the interconnect,
but the most likely is the MMCI, as transfers of these
sizes work fine for other devices using the same DMA
engine. DMA works fine also with SDIO as long as the
blocksize is a power of 2.

This patch has proven necessary for enabling SDIO for WLAN on
PostmarketOS-based Ux500 platforms.

What we managed to test in practice is Broadcom WiFi over
SDIO on the Ux500 based Samsung GT-I8190 and GT-S7710.
This WiFi chip, BCM4334 works fine after the patch.

Before this patch:

brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac4334-sdio
	  for chip BCM4334/3
mmci-pl18x 80118000.sdi1_per2: unsupported block size (60 bytes)
brcmfmac: brcmf_sdiod_ramrw: membytes transfer failed
brcmfmac: brcmf_sdio_download_code_file: error -22 on writing
	  434236 membytes at 0x00000000
brcmfmac: brcmf_sdio_download_firmware: dongle image file download
	  failed

After this patch:

brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM4334/3 wl0:
	  Nov 21 2012 00:21:28 version 6.10.58.813 (B2) FWID 01-0

Bringing up networks, discovering networks with "iw dev wlan0 scan"
and connecting works fine from this point.

This patch is inspired by Ulf Hansson's patch
http://www.spinics.net/lists/linux-mmc/msg12160.html

As the DMA engines on these platforms may now get block sizes
they were not used to before, make sure to also respect if
the DMA engine says "no" to a transfer.

Make a drive-by fix for datactrl_blocksz, misspelled.

Cc: Ludovic Barre <ludovic.barre@st.com>
Cc: Brian Masney <masneyb@onstation.org>
Cc: Stephan Gerhold <stephan@gerhold.net>
Cc: Niklas Cassel <niklas.cassel@linaro.org>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20191217143952.2885-1-linus.walleij@linaro.org

platform_get_resource(pdev, IORESOURCE_IRQ) is not recommended for
requesting IRQ's resources, as they can be not ready yet. Using
platform_get_irq() instead is preferred for getting IRQ even if it
was not retrieved earlier.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Link: https://lore.kernel.org/r/20191215175120.3290-13-tiny.windzz@gmail.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Use devm_platform_ioremap_resource() to simplify code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Link: https://lore.kernel.org/r/20191215175120.3290-12-tiny.windzz@gmail.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Use devm_platform_ioremap_resource() to simplify code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Link: https://lore.kernel.org/r/20191215175120.3290-11-tiny.windzz@gmail.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Use devm_platform_ioremap_resource() to simplify code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20191215175120.3290-10-tiny.windzz@gmail.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Use devm_platform_ioremap_resource() to simplify code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Link: https://lore.kernel.org/r/20191215175120.3290-9-tiny.windzz@gmail.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Use devm_platform_ioremap_resource() to simplify code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Link: https://lore.kernel.org/r/20191215175120.3290-8-tiny.windzz@gmail.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Use devm_platform_ioremap_resource() to simplify code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Link: https://lore.kernel.org/r/20191215175120.3290-7-tiny.windzz@gmail.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Use devm_platform_ioremap_resource() to simplify code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20191215175120.3290-6-tiny.windzz@gmail.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Use devm_platform_ioremap_resource() to simplify code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Link: https://lore.kernel.org/r/20191215175120.3290-5-tiny.windzz@gmail.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Use devm_platform_ioremap_resource() to simplify code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Link: https://lore.kernel.org/r/20191215175120.3290-4-tiny.windzz@gmail.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Use devm_platform_ioremap_resource() to simplify code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Link: https://lore.kernel.org/r/20191215175120.3290-3-tiny.windzz@gmail.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Use devm_platform_ioremap_resource() to simplify code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20191215175120.3290-2-tiny.windzz@gmail.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Use devm_platform_ioremap_resource() to simplify code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20191215175120.3290-1-tiny.windzz@gmail.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Command queuing has been reported broken on some systems based on Intel
GLK. A separate patch disables command queuing in some cases.

This patch adds a quirk for broken command queuing, which enables users
with problems to disable command queuing using sdhci module parameters for
quirks.

Fixes: 8ee82bda ("mmc: sdhci-pci: Add CQHCI support for Intel GLK")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191217095349.14592-2-adrian.hunter@intel.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Command queuing has been reported broken on some Lenovo systems based on
Intel GLK. This is likely a BIOS issue, so disable command queuing for
Intel GLK if the BIOS vendor string is "LENOVO".

Fixes: 8ee82bda ("mmc: sdhci-pci: Add CQHCI support for Intel GLK")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191217095349.14592-1-adrian.hunter@intel.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The eSDHC on LS1088A platform uses 1/2 peripheral clock as base
clock.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Link: https://lore.kernel.org/r/20191216091911.14840-1-yangbo.lu@nxp.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Two previous patches introduced below quirks for P2020 platforms.
- SDHCI_QUIRK_RESET_AFTER_REQUEST
- SDHCI_QUIRK_BROKEN_TIMEOUT_VAL

The patches made a mistake to add them in quirks2 of sdhci_host
structure, while they were defined for quirks.
	host->quirks2 |= SDHCI_QUIRK_RESET_AFTER_REQUEST;
	host->quirks2 |= SDHCI_QUIRK_BROKEN_TIMEOUT_VAL;

This patch is to fix them.
	host->quirks |= SDHCI_QUIRK_RESET_AFTER_REQUEST;
	host->quirks |= SDHCI_QUIRK_BROKEN_TIMEOUT_VAL;

Fixes: 05cb6b2a ("mmc: sdhci-of-esdhc: add erratum eSDHC-A001 and A-008358 support")
Fixes: a46e4271 ("mmc: sdhci-of-esdhc: add erratum eSDHC5 support")
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191216031842.40068-1-yangbo.lu@nxp.comSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The stm32_sdmmc variant has build-in support for datatimeout for R1B
requests. If a corresponding IRQ is raised, this triggers the DPSM to stay
busy and remains in a non-functional state. Only a reset can bring it back
to a functional state.

Because a reset must be issued from non-atomic context, let's defer this to
be managed from a threaded IRQ handler. Besides the reset, the threaded
handler also calls mmc_request_done(), to finally complete the request.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Link: https://lore.kernel.org/r/20191211133934.16932-1-ludovic.Barre@st.com
[Ulf: A few minor updates to the changelog/comments]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Now that invert_gpio arguments are unused, let's remove them.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Link: https://lore.kernel.org/r/64d766d1f8af2e22bce32f4ffa453f7234207ad6.1576031637.git.mirq-linux@rere.qmqm.plSigned-off-by: Ulf Hansson <ulf.hansson@linaro.org>