Meraki MR26 is an EOL wireless access point featuring a
PoE ethernet port and two dual-band 3x3 MIMO 802.11n
radios and 1x1 dual-band WIFI dedicated to scanning.

Thank you Amir for the unit and PSU.

Hardware info:
SOC   : Broadcom BCM53015A1KFEBG (dual-core Cortex-A9 CPU at 800 MHz)
RAM   : SK Hynix Inc. H5TQ1G63EFR, 1 GBit DDR3 SDRAM = 128 MiB
NAND  : Spansion S34ML01G100TF100, 1 GBit SLC NAND Flash = 128 MiB
ETH   : 1 GBit Ethernet Port - PoE (TPS23754 PoE Interface)
WIFI0 : Broadcom BCM43431KMLG, BCM43431 802.11 abgn (3x3:3)
WIFI1 : Broadcom BCM43431KMLG, BCM43431 802.11 abgn (3x3:3)
WIFI2 : Broadcom BCM43428 "Air Marshal" 802.11 abgn (1x1:1)
BUTTON: One reset key behind a small hole next to the Ethernet Port
LEDS  : One amber (fault), one white (indicator) LED, separate RGB-LED
MISC  : Atmel AT24C64 8KiB EEPROM i2c
      : Ti INA219 26V, 12-bit, i2c output current/voltage/power monitor

SERIAL:
      WARNING: The serial port needs a TTL/RS-232 3V3 level converter!
      The Serial setting is 115200-8-N-1. The board has a populated
      right angle 1x4 0.1" pinheader.
      The pinout is: VCC (next to J3, has the pin 1 indicator), RX, TX, GND.

Odd stuff:

- uboot does not support lzma compression, but gzip'd uImage/DTB work.
- uboot claims to support FIT, but fails to pass the DTB to the kernel.
  Appending the dtb after the kernel image works.
- RGB-controller is supported through an external userspace program.
- The ubi partition contains a "board-config" volume. It stores the
  MAC Address (0x66 in binary) and Serial No. (0x7c alpha-numerical).
- SoC's temperature sensor always reports that it is on fire.
  This causes the system to immediately shutdown! Looking at reported
  "418 degree Celsius" suggests that this sensor is not working.

WIFI:
b43 is able to initialize all three WIFIs @ 802.11bg.
| b43-phy0: Broadcom 43431 WLAN found (core revision 29)
| bcma-pci-bridge 0000:01:00.0: bus1: Switched to core: 0x812
| b43-phy0: Found PHY: Analog 9, Type 7 (HT), Revision 1
| b43-phy0: Found Radio: Manuf 0x17F, ID 0x2059, Revision 0, Version 1
| b43-phy0 warning: 5 GHz band is unsupported on this PHY
| b43-phy1: Broadcom 43431 WLAN found (core revision 29)
| bcma-pci-bridge 0001:01:00.0: bus2: Switched to core: 0x812
| b43-phy1: Found PHY: Analog 9, Type 7 (HT), Revision 1
| b43-phy1: Found Radio: Manuf 0x17F, ID 0x2059, Revision 0, Version 1
| b43-phy1 warning: 5 GHz band is unsupported on this PHY
| b43-phy2: Broadcom 43228 WLAN found (core revision 30)
| bcma-pci-bridge 0002:01:00.0: bus3: Switched to core: 0x812
| b43-phy2: Found PHY: Analog 9, Type 4 (N), Revision 16
| b43-phy2: Found Radio: Manuf 0x17F, ID 0x2057, Revision 9, Version 1
| Broadcom 43xx driver loaded [ Features: NL ]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

mark the Meraki MR26 and its SoC (BCM53015) as supported
in the bindings documentation file.

<https://jp.broadcom.com/products/embedded-and-networking-processors/communications/bcm5301x>

"BCM53011 and BCM53015 with dual-core Cortex-A9 CPU at 800 MHz,
256KB L2 cache, 16-bit DDR2 interface, USB3, integrated switch,
GPHYs and packet accelerator"
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Add BCM6813 SoC device tree description to bcmbca binding document.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Add DTS for ARMv7 based broadband SoC BCM63148. bcm63148.dtsi is the SoC
description DTS header and bcm963148.dts is a simple DTS file for
Broadcom BCM963148 Reference board that only enable the UART port.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Add BCM63148 SoC device tree description to bcmbca binding document.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Add BCM6856 SoC device tree description to bcmbca binding document.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Add BCM63146 SoC device tree description to bcmbca binding document.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

gpio-keys children do not use unit addresses.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

The node names should be generic and DT schema expects certain pattern
(e.g. with key/button/switch).
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Add DTS for ARMv7 based broadband SoC BCM6756. bcm6756.dtsi is the SoC
description DTS header and bcm96756.dts is a simple DTS file for
Broadcom BCM96756 Reference board that only enable the UART port.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Add BCM6756 SoC device tree description to bcmbca binding document.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Add DTS for ARMv7 based broadband SoC BCM6855. bcm6855.dtsi is the SoC
description DTS header and bcm96855.dts is a simple DTS file for
Broadcom BCM96855 Reference board that only enable the UART port.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Add BCM6855 SoC device tree description to bcmbca binding document.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

This adds the entry for V3D for bcm2711 (used in the Raspberry Pi 4)
and the associated firmware clock entry.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Fix a few issue in bcm47622.dtsi file:
- Remove unnecessary cpu_on and cpu_off properties from psci node
- Add the missing gic registers and interrupts property to gic node
- Cosmetic changes
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Add DTS for ARMv7 based broadband SoC BCM6846. bcm6846.dtsi is the
SoC description DTS header and bcm96846.dts is a simple DTS file for
Broadcom BCM96846 Reference board that only enable the UART port.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Add BCM6846 SoC device tree description to bcmbca binding document.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Fix whitespace coding style: use single space instead of tabs or
multiple spaces around '=' sign in property assignment.  No functional
changes (same DTB).
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Add dts for ARMv7 based broadband SoC BCM6878. bcm6878.dtsi is the
SoC description dts header and bcm96878.dts is a simple dts file for
Broadcom BCM96878 Reference board that only enable the UART port.
Signed-off-by: Anand Gore <anand.gore@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Add BCM6878 SOC device tree description to bcmbca binding document.
Signed-off-by: Anand Gore <anand.gore@broadcom.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Add BCM6858 SOC device tree description to bcmbca binding document.
Signed-off-by: Anand Gore <anand.gore@broadcom.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Add BCM4912 SoC device tree description to bcmbca binding document.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Add BCM63158 SoC device tree description to bcmbca binding document.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Add dts for ARMv7 based broadband SoC BCM63178. bcm63178.dtsi is the
SoC description dts header and bcm963178.dts is a simple dts file for
Broadcom BCM963178 Reference board that only enable the UART port.
Signed-off-by: Anand Gore <anand.gore@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Add BCM63178 SOC device tree description to bcmbca binding document.
Signed-off-by: Anand Gore <anand.gore@broadcom.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Since commit 09453600 ("dt-bindings: display: Convert
VC4 bindings to schemas") it has been defined that the properties
'#address-cells' and '#size-cells' are not necessary for the dpi
node. This results in a warning during dtbs_check:

  dpi@7e208000: '#address-cells', '#size-cells' do not match any
  of the regexes: 'pinctrl-[0-9]+'

Since we don't need a reg property to differentiate between
multiple ports, drop them from the dtsi file.
Suggested-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Pull file descriptor fix from Al Viro:
 "Fix for breakage in #work.fd this window"

* tag 'pull-work.fd-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  fix the breakage in close_fd_get_file() calling conventions change

Pull mm hotfixes from Andrew Morton:
 "Fixups for various recently-added and longer-term issues and a few
  minor tweaks:

   - fixes for material merged during this merge window

   - cc:stable fixes for more longstanding issues

   - minor mailmap and MAINTAINERS updates"

* tag 'mm-hotfixes-stable-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
  mm/oom_kill.c: fix vm_oom_kill_table[] ifdeffery
  x86/kexec: fix memory leak of elf header buffer
  mm/memremap: fix missing call to untrack_pfn() in pagemap_range()
  mm: page_isolation: use compound_nr() correctly in isolate_single_pageblock()
  mm: hugetlb_vmemmap: fix CONFIG_HUGETLB_PAGE_FREE_VMEMMAP_DEFAULT_ON
  MAINTAINERS: add maintainer information for z3fold
  mailmap: update Josh Poimboeuf's email

Pull delay-accounting update from Andrew Morton:
 "A single featurette for delay accounting.

  Delayed a bit because, unusually, it had dependencies on both the
  mm-stable and mm-nonmm-stable queues"

* tag 'mm-nonmm-stable-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
  delayacct: track delays from write-protect copy

The bluetooth code uses our bitmap infrastructure for the two bits (!)
of connection setup flags, and in the process causes odd problems when
it converts between a bitmap and just the regular values of said bits.

It's completely pointless to do things like bitmap_to_arr32() to convert
a bitmap into a u32.  It shoudln't have been a bitmap in the first
place.  The reason to use bitmaps is if you have arbitrary number of
bits you want to manage (not two!), or if you rely on the atomicity
guarantees of the bitmap setting and clearing.

The code could use an "atomic_t" and use "atomic_or/andnot()" to set and
clear the bit values, but considering that it then copies the bitmaps
around with "bitmap_to_arr32()" and friends, there clearly cannot be a
lot of atomicity requirements.

So just use a regular integer.

In the process, this avoids the warnings about erroneous use of
bitmap_from_u64() which were triggered on 32-bit architectures when
conversion from a u64 would access two words (and, surprise, surprise,
only one word is needed - and indeed overkill - for a 2-bit bitmap).

That was always problematic, but the compiler seems to notice it and
warn about the invalid pattern only after commit 0a97953f ("lib: add
bitmap_{from,to}_arr64") changed the exact implementation details of
'bitmap_from_u64()', as reported by Sudip Mukherjee and Stephen Rothwell.

Fixes: fe92ee64 ("Bluetooth: hci_core: Rework hci_conn_params flags")
Link: https://lore.kernel.org/all/YpyJ9qTNHJzz0FHY@debian/
Link: https://lore.kernel.org/all/20220606080631.0c3014f2@canb.auug.org.au/
Link: https://lore.kernel.org/all/20220605162537.1604762-1-yury.norov@gmail.com/Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reported-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Reviewed-by: Yury Norov <yury.norov@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

It used to grab an extra reference to struct file rather than
just transferring to caller the one it had removed from descriptor
table.  New variant doesn't, and callers need to be adjusted.

Reported-and-tested-by: syzbot+47dd250f527cb7bebf24@syzkaller.appspotmail.com
Fixes: 6319194e ("Unify the primitives for file descriptor closing")
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Pull x86 SGX fix from Thomas Gleixner:
 "A single fix for x86/SGX to prevent that memory which is allocated for
  an SGX enclave is accounted to the wrong memory control group"

* tag 'x86-urgent-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/sgx: Set active memcg prior to shmem allocation

Pull x86 mm cleanup from Thomas Gleixner:
 "Use PAGE_ALIGNED() instead of open coding it in the x86/mm code"

* tag 'x86-mm-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/mm: Use PAGE_ALIGNED(x) instead of IS_ALIGNED(x, PAGE_SIZE)

Pull x86 microcode updates from Thomas Gleixner:

 - Disable late microcode loading by default. Unless the HW people get
   their act together and provide a required minimum version in the
   microcode header for making a halfways informed decision its just
   lottery and broken.

 - Warn and taint the kernel when microcode is loaded late

 - Remove the old unused microcode loader interface

 - Remove a redundant perf callback from the microcode loader

* tag 'x86-microcode-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/microcode: Remove unnecessary perf callback
  x86/microcode: Taint and warn on late loading
  x86/microcode: Default-disable late loading
  x86/microcode: Rip out the OLD_INTERFACE

Pull x86 cleanups from Thomas Gleixner:
 "A set of small x86 cleanups:

   - Remove unused headers in the IDT code

   - Kconfig indendation and comment fixes

   - Fix all 'the the' typos in one go instead of waiting for bots to
     fix one at a time"

* tag 'x86-cleanups-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86: Fix all occurences of the "the the" typo
  x86/idt: Remove unused headers
  x86/Kconfig: Fix indentation of arch/x86/Kconfig.debug
  x86/Kconfig: Fix indentation and add endif comments to arch/x86/Kconfig

Pull x86 boot update from Thomas Gleixner:
 "Use strlcpy() instead of strscpy() in arch_setup()"

* tag 'x86-boot-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/setup: Use strscpy() to replace deprecated strlcpy()

Pull clockevent/clocksource updates from Thomas Gleixner:

 - Device tree bindings for MT8186

 - Tell the kernel that the RISC-V SBI timer stops in deeper power
   states

 - Make device tree parsing in sp804 more robust

 - Dead code removal and tiny fixes here and there

 - Add the missing SPDX identifiers

* tag 'timers-core-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  clocksource/drivers/oxnas-rps: Fix irq_of_parse_and_map() return value
  clocksource/drivers/timer-ti-dm: Remove unnecessary NULL check
  clocksource/drivers/timer-sun5i: Convert to SPDX identifier
  clocksource/drivers/timer-sun4i: Convert to SPDX identifier
  clocksource/drivers/pistachio: Convert to SPDX identifier
  clocksource/drivers/orion: Convert to SPDX identifier
  clocksource/drivers/lpc32xx: Convert to SPDX identifier
  clocksource/drivers/digicolor: Convert to SPDX identifier
  clocksource/drivers/armada-370-xp: Convert to SPDX identifier
  clocksource/drivers/mips-gic-timer: Convert to SPDX identifier
  clocksource/drivers/jcore: Convert to SPDX identifier
  clocksource/drivers/bcm_kona: Convert to SPDX identifier
  clocksource/drivers/sp804: Avoid error on multiple instances
  clocksource/drivers/riscv: Events are stopped during CPU suspend
  clocksource/drivers/ixp4xx: Drop boardfile probe path
  dt-bindings: timer: Add compatible for Mediatek MT8186

Pull scheduler fix from Thomas Gleixner:
 "Fix the fallout of sysctl code move which placed the init function
  wrong"

* tag 'sched-urgent-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/autogroup: Fix sysctl move

Pull perf fixes from Thomas Gleixner:

  - Make the ICL event constraints match reality

  - Remove a unused local variable

* tag 'perf-urgent-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/core: Remove unused local variable
  perf/x86/intel: Fix event constraints for ICL