- 30 Mar, 2015 26 commits
-
-
Marek Vasut authored
Add new ID for ASUS N10 WiFi dongle. Signed-off-by:
Marek Vasut <marex@denx.de> Tested-by:
Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org>
-
Larry Finger authored
USB ID 2001:330d is used for a D-Link DWA-131. Signed-off-by:
-
Zhaoyang Liu authored
This patch adds recovery mechanism for SDIO RX during SKB allocation failures. For allocation failures during multiport aggregation, we skip and drop RX packets. For single port read case, we will use preallocated card->mpa_rx.buf to complete cmd53 read. Now we terminate SDIO operations only upon cmd53 failures. CC: James Cameron <quozl@laptop.org> Signed-off-by:
Zhaoyang Liu <liuzy@marvell.com> Signed-off-by:
Avinash Patil <patila@marvell.com> Signed-off-by:
-
Avinash Patil authored
Cancel all pending commands including scan commands and stop CAC during cfg80211 suspend handler. Signed-off-by:
-
Dan Carpenter authored
"adapter->sleep_cfm" is always non-NULL at this point. Static checkers complain that we already dereference it at the start of the function when we do: skb_put(adapter->sleep_cfm, sizeof(struct mwifiex_opt_sleep_confirm)); Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Acked-by:
Amitkumar Karwar <akarwar@marvell.com> Signed-off-by:
-
Maithili Hinge authored
SDIO reset was not happening properly on mwifiex as cancel_work_sync in mwifiex_sdio_remove used to kill the calling work function itself. Due to this, the interface was not getting removed and card was not getting added again. Reset work function has been made independent of adapter variable and cancel_work_sync has been moved to cleanup function. Signed-off-by:
Maithili Hinge <maithili@marvell.com> Signed-off-by:
-
Oleksij Rempel authored
Signed-off-by:
Oleksij Rempel <linux@rempel-privat.de> Signed-off-by:
-
Oleksij Rempel authored
replace REG_WRITE to REG_RMW and place every thing in one RMW buffer. Signed-off-by:
-
Oleksij Rempel authored
it is possible to reduce time needed for this function by rplacing REG_WRITE with REG_RMW (plus dummy 0) and putt all commands in same buffer. Signed-off-by:
-
Oleksij Rempel authored
it will reduce exution time from 14ms to 2ms on ar9271 Signed-off-by:
-
Oleksij Rempel authored
use REG_RMW in ath9k_hw_analog_shift_rmw. It will double execution speed on usb bus. Signed-off-by:
-
Oleksij Rempel authored
Signed-off-by:
-
Oleksij Rempel authored
Signed-off-by:
-
Oleksij Rempel authored
Signed-off-by:
-
Oleksij Rempel authored
Signed-off-by:
-
Oleksij Rempel authored
Signed-off-by:
-
Oleksij Rempel authored
this will reduce some overhead on usb bus. Signed-off-by:
-
Oleksij Rempel authored
insted of reading each register separatly and waste 4ms on each operation, we can use one shot read. Signed-off-by:
-
Oleksij Rempel authored
REG_READ generate most overhead on usb bus. It send and read micro packages and reduce usb bandwidth. To reduce this overhead we should read in batches. Signed-off-by:
-
Oleksij Rempel authored
Signed-off-by:
-
Oleksij Rempel authored
Signed-off-by:
-
Oleksij Rempel authored
Signed-off-by:
-
Oleksij Rempel authored
This function uses mixed styles for register names/numbers which is make harder reading and optimisation. Signed-off-by:
-
Oleksij Rempel authored
Since usb bus add extra delay on each request, a command with read + write requests is too expensive. We can dramtically reduce usb load by moving this command to firmware. In my tests, this patch will reduce channel scan time for about 5-10 seconds. Signed-off-by:
-
Taehee Yoo authored
I changed REG_CR+2 and (MSR) to MSR because MSR is defined as (REG_CR + 2). Signed-off-by:
Taehee Yoo <ap420073@gmail.com> Acked-by:
-
Stanislaw Gruszka authored
Seems H/W report correctly firmware Autorun value only at initialization stage. When we close interface and open it again, Autorun value is 0 and we try to load firmware what kills the device. To fix clear REQUIRE_FIRMWARE firmware flag, to do not load firmware again, once we discover Autorun mode. Reported-and-tested-by:
Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by:
Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by:
-
- 21 Mar, 2015 1 commit
-
-
Sujith Manoharan authored
AIC needs to be registered only when BTCOEX is enabled. This fixes the error reported by kbuild: >> ERROR: "ar9003_hw_attach_aic_ops" [drivers/net/wireless/ath/ath9k/ath9k_hw.ko] undefined! Signed-off-by:
Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by:
-
- 20 Mar, 2015 13 commits
-
-
Rafał Miłecki authored
Some BCM47XX SoC routers have LEDs connected to extra PCIe bcma buses. Handling them in arch code requires predictable GPIO numbers. Signed-off-by:
Rafał Miłecki <zajec5@gmail.com> Signed-off-by:
-
Avinash Patil authored
With patch '960d6d08 "mwifiex: delay skb allocation for RX until cmd53 over"' we no more pass skb parameter to MP aggregation setup helper function. We instead pass length to be aggregated. This patch fixes an issue where we were passing length parameter of NULL skb to aggregation routine resulting into crash. We should instead pass rx_len received from mp_regs. Signed-off-by:
-
Arend van Spriel authored
There are no known BCM4354 PCIe devices released so removing support from the driver until proven otherwise. Reviewed-by:
Hante Meuleman <meuleman@broadcom.com> Reviewed-by:
Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by:
Arend van Spriel <arend@broadcom.com> Signed-off-by:
-
Arend van Spriel authored
Recently support was added for the BCM4345 SDIO chipset by commit 9c510265 ("brcmfmac: Add support for BCM4345 SDIO chipset") however this was verified using a BCM43455 device, which is a more recent revision of the chip. This patch assure that older revisions are not probed as they would fail. Reviewed-by:
Syed Asifful Dayyan <syedd@broadcom.com> Reviewed-by:
-
Arend van Spriel authored
This patch added support for the BCM43430 802.11n SDIO chipset. Reviewed-by:
Daniel (Deognyoun) Kim <dekim@broadcom.com> Reviewed-by:
Franky (Zhenhui) Lin <frankyl@broadcom.com> Reviewed-by:
-
Arend van Spriel authored
The BCM4356 PCIe wireless device was added recently but overlooked the fact that the MODULE_FIRMWARE() macros were missing for the firmwares needed by this device. Reviewed-by:
-
Hante Meuleman authored
Reviewed-by:
-
Hante Meuleman authored
Reviewed-by:
-
Hante Meuleman authored
SDIO uses a thread to handle all communication with the device, for this data is exchanged between threads. This data needs proper memory barriers to make sure that data "exchange" is going correct. Reviewed-by:
-
Arend van Spriel authored
Several host controllers supporting runtime-pm are causing issues with our sdio wireless cards because they disable the sdio interrupt upon going into runtime suspend. This patch avoids that by doing a pm_runtime_forbid() call during the probe. Tested with Sony Vaio Duo 13 which uses sdhci-acpi host controller. Reviewed-by:
-
Dan Carpenter authored
It's clear from the indenting that curly braces were intended here. Fixes: e35000ea ('mwifiex: preprocess packets from TX queue') Signed-off-by:
-
Scott Branden authored
Add the USB Id to link the D-Link DWA 130 USB Wifi adapter to the rt2830 driver. Signed-off-by:
Scott Branden <sbranden@broadcom.com> Signed-off-by:
Pieter Truter <ptruter@broadcom.com> Signed-off-by:
-
Vladimir Kondratiev authored
Multicast is not yet properly supported for all connection types; actually, only non-secure AP is supported. For all other cases, fall back to old "pseudo-DMS" approach. Namely, for: - PBSS - secure connection When re-routing MCAST Rx->Tx on the AP, do not Tx back to the origin of the frame Signed-off-by:
Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> Signed-off-by:
-
