- 17 May, 2021 40 commits
-
-
Oleksij Rempel authored
Basically the TI TSC2046 touchscreen controller is 8 channel ADC optimized for the touchscreen use case. By implementing it as an IIO ADC device, we can make use of resistive-adc-touch and iio-hwmon drivers. Polled readings are currently not implemented to keep this patch small, so iio-hwmon will not work out of the box for now. So far, this driver was tested with a custom version of resistive-adc-touch driver, since it needs to be extended to make use of Z1 and Z2 channels. The X/Y are working without additional changes. Signed-off-by:
Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by:
Andy Shevchenko <andy.shevchenko@gmail.com> Link: https://lore.kernel.org/r/20210428073208.19570-4-o.rempel@pengutronix.deSigned-off-by:
Jonathan Cameron <Jonathan.Cameron@huawei.com>
-
Oleksij Rempel authored
Add a binding documentation for the TI TSC2046 touchscreen controllers ADC functionality. Signed-off-by:
Rob Herring <robh@kernel.org> Link: https://lore.kernel.org/r/20210428073208.19570-3-o.rempel@pengutronix.deSigned-off-by:
-
Oleksij Rempel authored
Settling time and over sampling is a typical challenge for different IIO ADC devices. So, introduce channel specific settling-time-us and oversampling-ratio properties to cover this use case. Signed-off-by:
-
Mauro Carvalho Chehab authored
Commit 63cd35f3 ("iio: Documentation: update definitions for bufferY and scan_elements") updated iio documentation in order to point to the newly per-buffer API, as it is now possible to support multi buffers. While the previous ABI will be kept forever, the best is for applications to use the 5.11+ ABI. So, move the legacy one ABI/obsolete. This fixes an issue with scripts/get_abi.pl, that doesn't accept two different Kernel version support for the same API set. Fixes: 63cd35f3 ("iio: Documentation: update definitions for bufferY and scan_elements") Signed-off-by:
Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Link: https://lore.kernel.org/r/a2c802049adee6a5710a58082cfdc1132c5e4c11.1619532170.git.mchehab+huawei@kernel.orgSigned-off-by:
-
Jonathan Cameron authored
W=1 highlights these two cases that are obviously not in kernel-doc format. Signed-off-by:
Fabrice Gasnier <fabrice.gasnier@foss.st.com>
-
Tomasz Duszynski authored
sps30 has gained support for serial communication so add example to the binding file. While at it remove reg property from list of required properties because it's no-op in case of serial communication. Signed-off-by:
Tomasz Duszynski <tomasz.duszynski@octakon.com> Signed-off-by:
-
Tomasz Duszynski authored
Sensor has support for both i2c and serial communication interfaces. Both offer very similar set of features. Minor differences don't impact overall functionality like doing measurements, etc. Support for i2c have already been added, this patch adds support for the latter ie. serial interface. Signed-off-by:
-
Tomasz Duszynski authored
Move code responsible for handling i2c communication to a separate file. Rationale for this change is preparation for adding support for serial communication. Signed-off-by:
-
Jonathan Cameron authored
The adf4371 has channels that are very closely coupled, so additional documentation is needed to express these constraints. Unfortunately having the same sysfs filename in multiple documentation does not work well when generating automated documentation. To avoid this issue, we add a new device specific description to the main docs and remove the one in the device specific file. Fixes $ scripts/get_abi.pl validate Warning: /sys/bus/iio/devices/iio:deviceX/out_altvoltageY_frequency is defined 2 times: ./Documentation/ABI/testing/sysfs-bus-iio-frequency-adf4371:0 ./Documentation/ABI/testing/sysfs-bus-iio:599 Cc: Alexandru Ardelean <alexandru.ardelean@analog.com> Reported-by:
-
Jonathan Cameron authored
This one is challenging as both the places this appears in specific drivers are making 'unusual' uses of what looks like a simple output current channel. As a side note, this was particular bit of ABI occurs in other drivers where the use is much more straight forward e.g. dac/ad5421 This patch attempts to make a best effort of adding it to the main docs but retaining enough information. Both of these drivers probably need specific documents being written to describe their unusual interfaces, but those should be in the main documentation, not under Documentation/ABI. That is a non trivial job so left for another time. Fixes $ scripts/get_abi.pl validate Warning: /sys/bus/iio/devices/iio:deviceX/out_currentY_raw is defined 2 times: ./Documentation/ABI/testing/sysfs-bus-iio-light-lm3533-als:43 ./Documentation/ABI/testing/sysfs-bus-iio-health-afe440x:38 Reported-by:
-
Jonathan Cameron authored
The interface is standard and the extra info provided on exactly what is being powered down is not of interest to most users. Hence this doesn't need it's own documentation and can rely on the docs in sysfs-bus-iio Fixes $ scripts/get_abi.pl validate Warning: /sys/bus/iio/devices/iio:deviceX/out_altvoltageY_powerdown is defined 2 times: ./Documentation/ABI/testing/sysfs-bus-iio-frequency-adf4371:36 ./Documentation/ABI/testing/sysfs-bus-iio:588 Cc: Alexandru Ardelean <alexandru.ardelean@analog.com> Reported-by:
-
Jonathan Cameron authored
This device has the unusual characteristic that the calibbias values have well defined units (more commonly they are tweaks to a DAC) Unfortunately the previous approach of having more specific documentation in sysfs-bus-iio-icm42600 results in warnings during the documentation build and random ordering in the resulting documentation. To avoid this, add a note to the main documentation on this special characteristic for the icm42600. The _available for calibbias was missing from the main sysfs-bus-iio docs so also add that, allowing us to drop the icm42600 specific file. Fixes $ scripts/get_abi.pl validate warning: Warning: /sys/bus/iio/devices/iio:deviceX/in_accel_x_calibbias is defined 2 times: ./Documentation/ABI/testing/sysfs-bus-iio-icm42600:0 ./Documentation/ABI/testing/sysfs-bus-iio:394 Warning: /sys/bus/iio/devices/iio:deviceX/in_accel_y_calibbias is defined 2 times: ./Documentation/ABI/testing/sysfs-bus-iio-icm42600:1 ./Documentation/ABI/testing/sysfs-bus-iio:395 Warning: /sys/bus/iio/devices/iio:deviceX/in_accel_z_calibbias is defined 2 times: ./Documentation/ABI/testing/sysfs-bus-iio-icm42600:2 ./Documentation/ABI/testing/sysfs-bus-iio:396 Warning: /sys/bus/iio/devices/iio:deviceX/in_anglvel_x_calibbias is defined 2 times: ./Documentation/ABI/testing/sysfs-bus-iio-icm42600:3 ./Documentation/ABI/testing/sysfs-bus-iio:397 Warning: /sys/bus/iio/devices/iio:deviceX/in_anglvel_y_calibbias is defined 2 times: ./Documentation/ABI/testing/sysfs-bus-iio-icm42600:4 ./Documentation/ABI/testing/sysfs-bus-iio:398 Warning: /sys/bus/iio/devices/iio:deviceX/in_anglvel_z_calibbias is defined 2 times: ./Documentation/ABI/testing/sysfs-bus-iio-icm42600:5 ./Documentation/ABI/testing/sysfs-bus-iio:399 Cc: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com> Reported-by:
-
Nuno Sa authored
With commit 3ba10e37371d ("iio: adis: add burst_max_speed_hz variable"), we just need to define 'burst_max_speed_hz' and the adis core will take care of setting up the spi transfers for burst mode. Hence, we fix a potential race with the spi core where we could be left witn an invalid 'max_speed_hz'. Reviewed-by:Alexandru Ardelean <ardeleanalex@gmail.com> Fixes: 5eda3550 ("staging:iio:adis16400: Preallocate transfer message") Signed-off-by:
Nuno Sa <nuno.sa@analog.com> Link: https://lore.kernel.org/r/20210427085454.30616-7-nuno.sa@analog.comSigned-off-by:
-
Nuno Sa authored
With commit 3ba10e37371d ("iio: adis: add burst_max_speed_hz variable"), we just need to define 'burst_max_speed_hz' and the adis core will take care of setting up the spi transfers for burst mode. Hence, we fix a potential race with the spi core where we could be left with an invalid 'max_speed_hz'. Reviewed-by: -
Nuno Sa authored
Typically, in burst mode, the device cannot operate at it's full spi speed. Hence, the spi transfers for burst mode have to take this into account. With this change we avoid a potential race with the spi core as drivers were 'hacking' the device 'max_speed_hz' directly in the trigger handler. Reviewed-by:
-
Nuno Sa authored
There's no point in pushing data to IIO buffers in case 'spi_sync()' fails. Reviewed-by:
-
Nuno Sa authored
It makes more sense to update the device page as soon as we we successfully changed it. Moreover, a follow up patch will handle 'spi_sync' error path which would leave 'current_page' in a inconsistent state. Signed-off-by:
-
Nuno Sa authored
On an IRQ handler we should not return normal error codes as 'irqreturn_t' is expected. This is done by jumping to the 'check_burst32' label where we return 'IRQ_HANDLED'. Note that it is fine to do the burst32 check in this error path. If we have proper settings to apply burst32, we might just do the setup now so that the next sample already uses it. Fixes: fff7352b ("iio: imu: Add support for adis16475") Reviewed-by:
-
Tomas Melin authored
Add initial support for Murata SCA3300 3-axis industrial accelerometer with digital SPI interface. This device also provides a temperature measurement. Datasheet: https://www.murata.com/en-global/products/sensor/accel/sca3300Signed-off-by:
Tomas Melin <tomas.melin@vaisala.com> Reviewed-by:
-
Tomas Melin authored
initial DT bindings for Murata SCA3300 Accelerometer. Signed-off-by:
-
Jonathan Cameron authored
This binding covers class of simple SPI ADCs which only provide data output - they don't have MOSI pin. The only real variation between them is over how many supplies they use and which one is used for the reference. Michael listed as maintainer for this one as it is his driver and falls under the catch all MAINTAINERS entry for ADI devices. Signed-off-by:
-
Jonathan Cameron authored
Not all of the parts supported by this driver use single supply. Hence we add chip_info fields to say what additional supplies exist and in the case of vref, ensure that is used for the reference voltage rather than vcc. One corner case is the ad7091r which has an internal reference that can be over-driven by an external reference connected on the vref pin. To handle that force_ext_vref is introduced and set if an optional vref regulator is present. Tested using really simple QEMU model and some fixed regulators. The devm_add_action_or_reset() callback is changed to take the regulator as it's parameter so we can use one callback for all the different regulators without having to store pointers to them in the iio_priv() structure. Signed-off-by:
kernel test robot <lkp@intel.com> Reviewed-by:
Lars-Peter Clausen <lars@metafoo.de> Link: https://lore.kernel.org/r/20210425163154.73209-2-jic23@kernel.org
-
Jonathan Cameron authored
Fairly simple conversion with the exception of the XOR between spi-cpha and spi-cpol. Signed-off-by:
-
Jonathan Cameron authored
These are never upper case. Chances are that all users of this driver were using the ACPI binding but just in case keep the uppercase version but mark it deprecated. Whilst here tidy up some spacing. Signed-off-by:
-
Jonathan Cameron authored
The device has a tsens-busy pin, but it's both fiddly and currently ignored by the Linux driver. Given it's not clear whether the binding should be an interrupt, or a GPIO I have left that out for now. Signed-off-by:
-
Jonathan Cameron authored
Two simple devices. The stk8ba50 datasheet could be found via google, but I only have the driver for the 8312. Given they both seem to be 3 axis devices with a single interrupt line, add them to trivial-devices.yaml Signed-off-by:
-
Jonathan Cameron authored
Simple devices with I2C interface and single interrupt line so entries in trivial devices are sufficient. Signed-off-by:
-
Jonathan Cameron authored
Binding documentation for this driver was missing. Note that the binding and some in tree dts files specifiy interrupts etc but the driver is fairly simple and does not yet make use of them. Listed both Joachim and myself as maintainers for this binding on basis it's Joachim's driver but I don't want to volunteer Joachim too strongly to look after this doc. Signed-off-by:
-
Jonathan Cameron authored
Linux driver currently relies on the driver.name to match to the compatible, but that doesn't mean it isn't a good idea to document it. Only real complexity is the 3 separate power supplies. Signed-off-by:
-
Jonathan Cameron authored
These two devices have different internal characteristics, but their external connectivity and as a result device tree descriptions are identical. Note that neither driver in Linux currently has an of_match_table but instead rely on matching via name alone. Signed-off-by:
-
Yicong Yang authored
Use devm_add_action_or_reset() instead of devres_alloc() and devres_add(), which works the same. This will simplify the code. There is no functional changes. Signed-off-by:
Yicong Yang <yangyicong@hisilicon.com> Reviewed-by:
-
Yicong Yang authored
Use devm_add_action_or_reset() instead of devres_alloc() and devres_add(), which works the same. This will simplify the code. There is no functional changes. Signed-off-by:
-
Yicong Yang authored
Use devm_add_action_or_reset() instead of devres_alloc() and devres_add(), which works the same. This will simplify the code. There is no functional changes. Signed-off-by:
-
Yicong Yang authored
Use devm_add_action_or_reset() instead of devres_alloc() and devres_add(), which works the same. This will simplify the code. There is no functional changes. Signed-off-by:
-
Yicong Yang authored
Use devm_add_action_or_reset() instead of devres_alloc() and devres_add(), which works the same. This will simplify the code. There is no functional changes. Signed-off-by:
-
Yicong Yang authored
Use devm_add_action_or_reset() instead of devres_alloc() and devres_add(), which works the same. This will simplify the code. There is no functional changes. Signed-off-by:
-
Yicong Yang authored
Use devm_add_action_or_reset() instead of devres_alloc() and devres_add(), which works the same. This will simplify the code. There is no functional changes. Signed-off-by:
-
Joe Sandom authored
Device tree binding for AMS/TAOS tsl2591 ambient light sensor. This driver supports configuration via device tree and sysfs. Supported channels for raw infrared light intensity, raw combined light intensity and illuminance in lux. The driver additionally supports iio events on lower and upper thresholds. This is a very-high sensitivity light-to-digital converter that transforms light intensity into a digital signal. Signed-off-by:
Joe Sandom <joe.g.sandom@gmail.com> Reviewed-by:
-
Joe Sandom authored
Driver implementation for AMS/TAOS tsl2591 ambient light sensor. This driver supports configuration via device tree and sysfs. Supported channels for raw infrared light intensity, raw combined light intensity and illuminance in lux. The driver additionally supports iio events on lower and upper thresholds. This is a very-high sensitivity light-to-digital converter that transforms light intensity into a digital signal. Datasheet: https://ams.com/tsl25911#tab/documentsSigned-off-by:
-
Nuno Sa authored
On the trigger handler, we might need to change the device page. Hence, we should check the return value from 'spi_write()' and act accordingly. Signed-off-by:
-
