The jr instruction opcode has changed in R6 so make sure
the correct ISA level is set prior using that instruction.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>

Add the MIPS R6 related preprocessor definitions for FPU signal
related functions. MIPS R6 only has FR=1 so avoid checking that
bit on the C0/Status register.
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>

Add the MIPS R6 related preprocessor definitions for save/restore
FPU related functions. We also set the appropriate ISA level
so the final return instruction "jr ra" will produce the correct
opcode on R6.
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>

Add MIPS R6 support to cache and ftlb exceptions, as well as
to the hwrena and ebase register configuration.
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>

Print 'mips64r6' and/or 'mips32r6' if the kernel is running on
a MIPS R6 core.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>

The instruction hazard barrier in the form of:

jr.hb	ra
nop

is valid on MIPS R6 as well.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>

Add MIPS R6 support when decoding the config0 c0 register.
Also add MIPS R6 support when examining the ebase c0 register
to get the core number and when getting the shadow set number
from the srsctl c0 register.
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>

Just like MIPS R2, in MIPS R6 it is possible to determine if a
timer interrupt has happened or not.
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>

The current HW bugs checked in cpu-bugs64, do not apply to R6 cores
and they cause compilation problems due to removed <R6 instructions,
so do not check for them for the time being.
Reviewed-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>

MIPS R6 changed the opcodes for LL/SC instructions so we need to set
the appropriate ISA level.

Cc: Matthew Fortune <Matthew.Fortune@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>

"sub $reg, imm" is not a real MIPS instruction. The assembler can
replace that with "addi $reg, -imm". However, addi has been removed
from R6, so we replace the "sub" instruction with the "addiu" one.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>

MIPS R6 changed the opcodes for LL/SC instructions so we need to set
the appropriate ISA level.

Cc: Matthew Fortune <Matthew.Fortune@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>

MIPS R6 changed the opcodes for LL/SC instructions so we need to set
the correct ISA level.

Cc: Matthew Fortune <Matthew.Fortune@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>

MIPS R6 changed the opcodes for LL/SC instructions so we need to
set the correct ISA level.

Cc: Matthew Fortune <Matthew.Fortune@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>

MIPS R6 changed the opcodes for LL/SC instructions so we need to set
the correct ISA.

Cc: Matthew Fortune <Matthew.Fortune@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>

GCC versions supporting MIPS R6 use the ZC constraint to enforce a
9-bit offset for MIPS R6. We will use that for all MIPS R6 LL/SC
instructions.

Cc: Matthew Fortune <Matthew.Fortune@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>

The GCC_OFF12_ASM macro is used for 12-bit immediate constrains
but we will also use it for 9-bit constrains on MIPS R6 so we
rename it to something more appropriate.

Cc: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>

MIPS R6, just like MIPS R2, have scratch pad storage, so add a new
symbol which is selected by MIPS R2 and R6.

Link: http://www.linux-mips.org/archives/linux-mips/2015-01/msg00389.html
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>

MIPS R6 changed the 'cache' instruction opcode and reduced the
offset field to 8 bits. This means we now have to adjust the
base register every 256 bytes and as a result of which we can
no longer use the previous cache functions.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>

Add the MIPS R6 related definitions to the IRQ related macros
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>

Add the MIPSR6 related definitions to MIPS hazards
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>

Add MIPS R6 to the ISA definitions
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>

The following instructions have been removed from MIPS R6

ulw, ulh, swl, lwr, lwl, swr.

However, all of them are used in the MIPS specific checksum implementation.
As a result of which, we will use the generic checksum on MIPS R6
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>

The "add" instruction is actually a macro in binutils and depending on
the size of the immediate it can expand to an "addi" instruction.
However, the "addi" instruction traps on overflows which is not
something we want on address calculation.

Link: http://www.linux-mips.org/archives/linux-mips/2015-01/msg00121.html
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: <stable@vger.kernel.org> # v3.15+
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>

EI/DI instructions are available in MIPS R6 so add the needed
definitions.
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>

The HI/LO registers have been removed from MIPS R6. Instructions
such as MULT and DIV have been replaced with a new pair of
instructions for the HI/LO operations for example:

MULT -> MUL, MUH
DIV -> DIV, MOD

So we avoid preserving the pre-R6 HI/LO registers in MIPS R6
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>

Define the MODULE_PROC_FAMILY for the MIPS R6 ISA.
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>

There are certain places where the code uses .set mips32 or .set mips64
or .set arch=r4000. In preparation of MIPS R6 support, and in order to
use as less #ifdefs as possible, we define new macros to set similar
annotations for MIPS R6.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>

MIPS R6 defines new opcodes for ll, sc, cache and pref instructions
so we need to take these into consideration in the micro-assembler.
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>

MIPS R6 redefines several instructions and reduces the immediate
field to 9-bits so add related macros for the microassembler.
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>

Add build support for the latest revision (R6) of the MIPS ISA.
microMIPS is not yet supported.

Link: http://www.linux-mips.org/archives/linux-mips/2015-01/msg00386.html
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>

Add a case in cpu_probe_mips for the MIPS generic QEMU processor ID.
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>

Add a CPU_QEMU_GENERIC case to various switch statements.
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>

Latest versions of QEMU added support for mips32r6-generic and
mips64r6-generic cpu types so add related definitions in preparation
of MIPS R6 support. This is also used for QEMU R2 generic cpus.
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>

We need to check the ASEs support against the core's CFLAGS instead
of depending to the default -march option from the toolchain.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9180/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

activate_mm() and switch_mm() call get_new_mmu_context() which in turn
can enable the HTW before the entryhi is changed with the new ASID.
Since the latter will enable the HTW in local_flush_tlb_all(),
then there is a small timing window where the HTW is running with the
new ASID but with an old pgd since the TLBMISS_HANDLER_SETUP_PGD
hasn't assigned a new one yet. In order to prevent that, we introduce a
simple htw counter to avoid starting HTW accidentally due to nested
htw_{start,stop}() sequences. Moreover, since various IPI calls can
enforce TLB flushing operations on a different core, such an operation
may interrupt another htw_{stop,start} in progress leading inconsistent
updates of the htw_seq variable. In order to avoid that, we disable the
interrupts whenever we update that variable.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: <stable@vger.kernel.org> # 3.17+
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9118/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Whenever we modify a page table entry, we need to ensure that the HTW
will not fetch a stable entry. And for that to happen we need to ensure
that HTW is stopped before we modify the said entry otherwise the HTW
may already be in the process of reading that entry and fetching the
old information. As a result of which, we replace the htw_reset() calls
with htw_{stop,start} in more appropriate places. This also removes the
remaining users of htw_reset() and as a result we drop that macro
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: <stable@vger.kernel.org> # 3.17+
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9116/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

When we use htw_{start,stop}() outside of htw_reset(), we need
to ensure that c0 changes have been propagated properly before
we attempt to continue with subsequence memory operations.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: <stable@vger.kernel.org> # 3.17+
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9114/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Commit 41c594ab ("[MIPS] MT: Improved multithreading support.")
removed useful debug information for userland segmentation faults.
This patch bring this back along with the ability to determine the
name of the object file where the EPC and RA registers point at.
Furthermore, we select the SYSCTL_EXCEPTION_TRACE symbol for MIPS
which is the de facto solution to turn userland exception logging
on and off via the /proc/sys/debug/exception-trace file.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9089/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

Userland code may be built using an ABI which permits linking to objects
that have more restrictive floating point requirements. For example,
userland code may be built to target the O32 FPXX ABI. Such code may be
linked with other FPXX code, or code built for either one of the more
restrictive FP32 or FP64. When linking with more restrictive code, the
overall requirement of the process becomes that of the more restrictive
code. The kernel has no way to know in advance which mode the process
will need to be executed in, and indeed it may need to change during
execution. The dynamic loader is the only code which will know the
overall required mode, and so it needs to have a means to instruct the
kernel to switch the FP mode of the process.

This patch introduces 2 new options to the prctl syscall which provide
such a capability. The FP mode of the process is represented as a
simple bitmask combining a number of mode bits mirroring those present
in the hardware. Userland can either retrieve the current FP mode of
the process:

  mode = prctl(PR_GET_FP_MODE);

or modify the current FP mode of the process:

  err = prctl(PR_SET_FP_MODE, new_mode);
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Matthew Fortune <matthew.fortune@imgtec.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8899/Signed-off-by: Ralf Baechle <ralf@linux-mips.org>