TI's opt3001 light sensor is a simple and yet powerful
little device. The device provides 99% IR rejection,
automatic full-scale, very low power consumption and
measurements from 0.01 to 83k lux.

This patch adds support for that device using the IIO
framework.

See http://www.ti.com/product/opt3001 for more information.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

This cleans up the most ugly workaround in this driver. There are no
functional changes yet in the decoding algorithm, but we improve the
following things:
 * Get rid of spurious warning messages on systems with fast HRTIMER.
 * If the clock is not fast enough for decoding to work, we give
   up immediately.
 * In that case we return EAGAIN instead of EIO, so it's easier to
   discriminate causes of failure.

Returning EAGAIN is somewhat controversial: It's technically correct
as a faster clock might become available. OTOH once all clocks are
enabled this is a permanent error. There is no ECLOCKTOOSLOW error
code.
Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

We just do the assignments in two steps.
Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Explain why the driver needs a mutex.
Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

* add spaces around binary operators in cases where it reduces readability
* align multiline statements around opening parenthesis
Reported-by: Hartmut Knaack <knaack.h@gmx.de>
	in Message-ID: <55919E72.3010807@gmx.de>
Signed-off-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

The driver currently does not take into account the minimum sample time
as per the Figure 6-8 Chapter 9.1.1 12-bit ADC electrical characteristics.
We set a static amount of cycles instead of considering the sample time
as a given value, which depends on hardware characteristics.

Determine sampling frequencies by first reading the device tree property
node and then calculating the required Long Sample Time Adder (LSTAdder)
value, based on the ADC clock frequency and sample time value obtained
from the device tree. This LSTAdder value is then used for calculating
the sampling frequencies possible.

In case the sample time property is not specified through the device
tree, a safe default value of 1000ns is assumed.
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

This adds support for Microchip's 13 bit 1 channel AD converter MCP3301
Signed-off-by: Andrea Galbusera <gizero@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Construct the scanmask using its descriptive axis names (as used in
iio_chan_spec) instead of a 'magic' value.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Signed-off-by: Jandy Gou <qingsong.gou@ck-telecom.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Signed-off-by: Jandy Gou <qingsong.gou@ck-telecom.com>
Acked-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Some macros and a function were missing the acpi_als_ prefix, so add it.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

In order to provide a channel name to in kernel consumers add the
datasheet names for every usable AD channel. Since the channel names
differ between i.MX23 and i.MX28, we need to separate the channel
specs.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

This patch reorder the header includes alphabetically.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

This patch removes the unnecessary header includes.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

This patch adds the missing include for mutex handling.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

This patch fix some spelling errors in the comments.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

At the beginning the driver supported only i.MX28 SoC, but now the
whole MXS platform. So remove any confusing comments which apply
only to i.MX28.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Remove sysfs bytes_per_datum device attribute ABI documentation
since the attribute is not present anymore.
Signed-off-by: Cristina Opriceana <cristina.opriceana@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Remove the duplicate code of dgap_remove_one() and dgap_stop().
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In a later patch we will remove the duplicate codes. But the code also
needs to execute dgap_remove_driver_sysfiles() if it is being called
from dgap_remove_one() but if being called fron the error path of the
dgap_init_module() then the sysfiles should not be removed.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Relocate the function dgap_stop() so that in a later patch we can remove
the duplicate codes between dgap_stop() and dgap_remove_one().
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The code in dgap_stop() is almost a duplicate of the code that will be
executed on pci_unregister_driver(). So the error code was stopping and
unregistering everything twice.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The variable ret was always 0. So remove the variable and always
return 0 from the function.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Stop using DBG_88E which is a custom macro for printing debugging
messages. Instead start using pr_debug and in the process define
pr_fmt.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The default value of status was _FAIL, it was only changed if kzalloc
succeeds and the check for status is immediately following kzalloc. We
can have the failure code in the else part as the failure code will be
executed only if kzalloc fails.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

By checking for the success of kzalloc we were able to remove the goto
label thus making the code more readable.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The check for pstat and pdvobjpriv is not required here as we have
already checked for them before.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The inline function rtw_set_ips_deny() was only defined but was never
used.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Now since the Big-Endian and Little-Endian based calculations are moved
into a macro we can make fb_read() and fb_write() common for both
Little-Endian and Big-Endian.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Define and use some new macros to work with different situations
based on little-endian and big-endian.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rtw_hal_write_rfreg() is never referenced, so remove it.

It used to be the only place where the write_rfreg callback was
called, so get rid of the function pointer as well.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Cc: Greg Kroah-Hartman <gregkh@linux.com>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rtw_hal_set_def_var() is never referenced, so remove it.

It used to be the only place where the SetHalDefVarHandler callback was
called, so get rid of the function pointer as well.

Also remove the callback itself, SetHalDefVar8188EUsb(), which was not
called anywhere else.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Cc: Greg Kroah-Hartman <gregkh@linux.com>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rtw_hal_enable_interrupt() and rtw_hal_disable_interrupt() are never
referenced, so remove them.

They used to be the only place where the enable_interrupt() and
disable_interrupt() callbacks were called, and the function pointer
is never set, so get rid of the function pointer as well.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Cc: Greg Kroah-Hartman <gregkh@linux.com>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

fixes "Possible unnecessary 'out of memory' message"
Signed-off-by: CHANG FU CHIAO <zector1030@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Variable obd_device_cachep is only used inside the file it is declared,
so it is better set as static
Signed-off-by: Pedro Marzo Perez <marzo.pedro@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ldlm_namespace_sysfs_unregister needs to be called ldlm_namespace_free_post
so that we don't have this dangling object there after the namespace
has disappeared.
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch simplifies uuid unparse logic by using sprintf "%pU" extension.
And eliminates the code with a coding style error:

ERROR: Macros with complex values should be enclosed in parentheses
+#define CONSUME(val, ptr) (val) = consume(sizeof(val), (ptr))
Signed-off-by: Vasiliy Korchagin <vasiliy.korchagin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The copyright statements in the drivers need to be correct and
consistent; this patch fixes the year for all of them, and makes the
statement text cover just the GPL V2.
Signed-off-by: Benjamin Romer <benjamin.romer@unisys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge tag 'iio-for-4.3a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next

Jonathan writes:

First round of new drivers, cleanups and functionality for IIO in the 4.3 cycle.

Core and tools new stuff
* Allow explicit flush of hardware fifo by using an non blocking read.
  This is needed to support some of the Android requirements for HW fifo
  devices - also makes sense generally and clarifies a corner of the ABI.
* Add some missing modifier names.  Mostly these exist for weird and
  wonderful event types, but should still be present in the name array.
* Update iio_event_monitor to cope with new channel types.
* generic_buffer gains support for single byte scan elements (no idea
  how this never got implemented before!)

New device support
* ROHM rpr0521 light and proximity sensor driver.
* bmc150 gains bmc156 support.
* ms5611 gains ms5607 temperature and pressure sensor support.

Driver functionality
* inv-mpu - add scale_available attributes to aid userspace in
  configuring these devices.
* isl29125 - add scale_available attributes.
* stk8ba50 - sampling frequency control, triggered buffer support.
* stk8312 - sampling frequency control, triggered buffer support.
* cc10001 - ensure ADC powered up at probe time if shared by non linux
  running CPUs.
* bmc150-magn - decouple the buffer and trigger allowing other triggers
  to be used to drive this device's sampling.
Documentation
* Add some previously missed *scale_available attributes to the ABI docs.

Cleanups
* Clarify some crazy naming in iio_triggered_buffer_setup that seems to
  have somehow ended up backwards (dates back a long way).  Avoid the top
  half and bottom half naming entirely given we are how dealing with a
  handler and a thread in all cases.
* Tools cleanup including coding style, variable naming improvements, also
  a new sanity check on a full event having been read.
* stk8ba50 - replace the scale table with a struct for clarity. Also suspend
  the sensor if an error occurs in init.
* hid-sensor-prox - drop uneeded line break.
* mma9551 - use size in words for word read / write avoiding accidental
  sending of an odd number of bytes.
* mma9553 - fix code alignment and document the use of a mutex.
* light/Kconfig - typo fix in commment.
* cm3323 - don't eat an error value, replace an unneeded local variable with
  a generic local variable with the same use, add some blank lines for clarity.
* pressure/Kconfig - typo in Measurement Specialties name.
* bmc150-accel - actually use a mask definition rather than repeating the
  value inline, code style cleanup.
* adc/Kconfig - general help description cleanup.
* ssp_sensors - drop redundant spi driver bus initialization (done in the
  spi core)
* tmp006 - use genmask rather than hand generated masks.
* ms5611 - drop IIO_CHAN_INFO_SCALE as this driver provides a processed
  output and as such the read only scale adds nothing useful.
* kxcjk-1013, adf4350, dummy - drop unwanted blank lines.
* Drop all owner assignments from i2c_drivers and this is done in the
  i2c core.

Fixes checkpatch.pl
WARNING: Missing a blank line after declarations
Signed-off-by: Juston Li <juston.h.li@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>