- 25 May, 2023 38 commits
-
-
Krzysztof Kozlowski authored
Match unit-address to reg entry to fix dtbs W=1 warnings: Warning (simple_bus_reg): /soc@0/pinctrl@f000000: simple-bus unit address format error, expected "f100000" Fixes: ffc50b2d ("arm64: dts: qcom: Add base SM8550 dtsi") Signed-off-by:
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Reviewed-by:
Konrad Dybcio <konrad.dybcio@linaro.org> Signed-off-by:
Bjorn Andersson <andersson@kernel.org> Link: https://lore.kernel.org/r/20230419211856.79332-17-krzysztof.kozlowski@linaro.org
-
Krzysztof Kozlowski authored
Match unit-address to reg entry to fix dtbs W=1 warnings: Warning (simple_bus_reg): /soc@0/crypto@1de0000: simple-bus unit address format error, expected "1dfa000" Fixes: 433477c3 ("arm64: dts: qcom: sm8550: add QCrypto nodes") Signed-off-by:
-
Krzysztof Kozlowski authored
Match unit-address to reg entry to fix dtbs W=1 warnings: Warning (simple_bus_reg): /soc@0/phy@88e9000: simple-bus unit address format error, expected "88e8000" Fixes: 2458a305 ("arm64: dts: qcom: sm8350: switch to combo usb3/dp phy") Signed-off-by:
-
Krzysztof Kozlowski authored
Match unit-address to reg entry to fix dtbs W=1 warnings: Warning (simple_bus_reg): /soc@0/phy@1c0f000: simple-bus unit address format error, expected "1c0e000" Fixes: 6daee406 ("arm64: dts: qcom: sm8350: add PCIe devices") Signed-off-by:
-
Krzysztof Kozlowski authored
Match unit-address to reg entry to fix dtbs W=1 warnings: Warning (simple_bus_reg): /soc@0/dma-controller@900000: simple-bus unit address format error, expected "9800000" Fixes: bc08fbf4 ("arm64: dts: qcom: sm8350: Define GPI DMA engines") Signed-off-by:
-
Krzysztof Kozlowski authored
Match unit-address to reg entry to fix dtbs W=1 warnings: Warning (simple_bus_reg): /soc@0/thermal-sensor@4410000: simple-bus unit address format error, expected "4411000" Fixes: 7b74cba6 ("arm64: dts: qcom: sm6115: Add TSENS node") Signed-off-by:
-
Krzysztof Kozlowski authored
Match unit-address to reg entry to fix dtbs W=1 warnings: Warning (simple_bus_reg): /soc@0/camss@a00000: simple-bus unit address format error, expected "acb3000" Fixes: d48a6698 ("arm64: dts: qcom: sdm845: Add CAMSS ISP node") Signed-off-by:
-
Krzysztof Kozlowski authored
Match unit-address to reg entry to fix dtbs W=1 warnings: Warning (simple_bus_reg): /soc/camss@ca00000: simple-bus unit address format error, expected "ca00020" Fixes: f3d5d3cc ("arm64: dts: qcom: sdm630: Configure the camera subsystem") Signed-off-by:
AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by:
-
Krzysztof Kozlowski authored
Match unit-address to reg entry to fix dtbs W=1 warnings: Warning (simple_bus_reg): /soc/camss@a00000: simple-bus unit address format error, expected "a34000" Fixes: e0531312 ("arm64: dts: qcom: msm8996: Add CAMSS support") Signed-off-by:
-
Krzysztof Kozlowski authored
Match unit-address to reg entry to fix dtbs W=1 warnings: Warning (simple_bus_reg): /soc/spmi@fc4c0000: simple-bus unit address format error, expected "fc4cf000" Fixes: b0ad598f ("arm64: dts: qcom: msm8994: Add SPMI PMIC arbiter device") Signed-off-by:
-
Krzysztof Kozlowski authored
Match unit-address to reg entry to fix dtbs W=1 warnings: Warning (simple_bus_reg): /soc@0/mmc@7824000: simple-bus unit address format error, expected "7824900" Warning (simple_bus_reg): /soc@0/mmc@7864000: simple-bus unit address format error, expected "7864900" Warning (simple_bus_reg): /soc@0/mmc@7a24000: simple-bus unit address format error, expected "7a24900" Fixes: 0484d3ce ("arm64: dts: qcom: Add DTS for MSM8976 and MSM8956 SoCs") Signed-off-by:
Marijn Suijten <marijn.suijten@somainline.org> Reviewed-by:
-
Krzysztof Kozlowski authored
Match unit-address to reg entry to fix dtbs W=1 warnings: Warning (simple_bus_reg): /soc@0/remoteproc@a21b000: simple-bus unit address format error, expected "a204000" Fixes: b1242864 ("arm64: dts: MSM8953: Add wcnss nodes") Signed-off-by:
-
Krzysztof Kozlowski authored
Match unit-address to reg entry to fix dtbs W=1 warnings: Warning (simple_bus_reg): /soc@0/iommu@1e00000: simple-bus unit address format error, expected "1e20000" Fixes: c0b9575a ("arm64: dts: qcom: msm8953: add APPS IOMMU") Signed-off-by:
-
Krzysztof Kozlowski authored
Match unit-address to reg entry to fix dtbs W=1 warnings: Warning (simple_bus_reg): /soc@0/remoteproc@a21b000: simple-bus unit address format error, expected "a204000" Fixes: 88106096 ("ARM: dts: msm8916: Add and enable wcnss node") Signed-off-by:
-
Krzysztof Kozlowski authored
Match unit-address to reg entry to fix dtbs W=1 warnings: Warning (simple_bus_reg): /soc@0/mmc@7824000: simple-bus unit address format error, expected "7824900" Warning (simple_bus_reg): /soc@0/mmc@7864000: simple-bus unit address format error, expected "7864900" Fixes: c4da5a56 ("arm64: dts: qcom: Add msm8916 sdhci configuration nodes") Signed-off-by:
-
Krzysztof Kozlowski authored
Match unit-address to reg entry to fix dtbs W=1 warnings: Warning (simple_bus_reg): /soc@0/camss@1b00000: simple-bus unit address format error, expected "1b0ac00" Fixes: 58f479f9 ("arm64: dts: qcom: msm8916: Add CAMSS support") Signed-off-by:
-
Krzysztof Kozlowski authored
Match unit-address to reg entry to fix dtbs W=1 warnings: Warning (simple_bus_reg): /soc/qrng@e1000: simple-bus unit address format error, expected "e3000" Fixes: 5bf63562 ("arm64: dts: ipq6018: Add a few device nodes") Signed-off-by:
-
Arnaud Vrac authored
Add pinctrl and qup nodes in msm8998 device tree to support spi. Values were ported from downstream msm-4.4 kernel. Signed-off-by:
Arnaud Vrac <avrac@freebox.fr> Signed-off-by:
-
Konrad Dybcio authored
Enable the notification LED(s) wired up to the PMI8994(6) LPG. Signed-off-by:
-
Konrad Dybcio authored
Enable Venus on Edo phones. The firmware is signed, as per usual. Signed-off-by:
-
Konrad Dybcio authored
Set up and enable SDHCI2 to enable the microSD slot on Kumano devices. Signed-off-by:
-
Konrad Dybcio authored
Sony - as per usual - used a whole bunch of GPIO-gated fixed voltage regulators for camera sensors on Kumano. Describe them and the corresponding pins. Signed-off-by:
-
Konrad Dybcio authored
Sony ever so graciously provides GPIO line names in their downstream kernel (though sometimes they are not 100% accurate and you can judge that by simply looking at them and with what drivers they are used). Add these to the common DTSI to better document the hardware. The pin assignment for TLMM is identical on both devices. Great job! Signed-off-by:
-
Konrad Dybcio authored
Sony ever so graciously provides GPIO line names in their downstream kernel (though sometimes they are not 100% accurate and you can judge that by simply looking at them and with what drivers they are used). Add these to the Griffin and Bahamut device trees to better document the hardware. They are the same on both devices! Very nice! Signed-off-by:
-
Dmitry Baryshkov authored
Unlike typical GIC interrupts, first cell for SPMI interrupts is the USID rather than GIC_SPI/GIC_PPI/GIC_LPI qualifier. Fix the resin interrupt to use USID value 0x0 rather than GIC_SPI define. Fixes: f86ae6f2 ("arm64: dts: qcom: sagit: add initial device tree for sagit") Signed-off-by:
Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Reviewed-by:
-
Jagadeesh Kona authored
Add device node for video clock controller on Qualcomm SM8550 platform. Signed-off-by:
Jagadeesh Kona <quic_jkona@quicinc.com> Signed-off-by:
-
Taniya Das authored
Add device node for video clock controller on Qualcomm SM8450 platform. Signed-off-by:
Taniya Das <quic_tdas@quicinc.com> Signed-off-by:
-
Bjorn Andersson authored
Merge the SM8450 Video Clock Controller DeviceTree binding topic branch in order to get access to the clock constants defined by the binding.
-
Taniya Das authored
Add device tree bindings for the video clock controller on Qualcomm SM8450 platform. Signed-off-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
Robert Marko authored
Add node to support the QUP5 SPI controller inside of IPQ8074. Some devices use this bus in order to manage external switches. Signed-off-by:
Robert Marko <robimarko@gmail.com> Signed-off-by:
-
Andrew Halaney authored
The mtl nodes aren't evaluated unless they're under the node with the compatible. Move them so they're now evaluated in case future patchsets modify them incorrectly. An example of this can be seen in the link. Link: https://lore.kernel.org/linux-arm-msm/20230414145844.wyg6pt623pzqwh5l@halaney-x13s/Signed-off-by:
Andrew Halaney <ahalaney@redhat.com> Reviewed-by:
Brian Masney <bmasney@redhat.com> Signed-off-by:
-
Andrew Halaney authored
Using interrupts-extended already indicates what the interrupt-parent is, so drop the explicit interrupt-parent. The comment about this being the phy-intr is not helpful either, since this is the only interrupt in the phy node. Suggested-by:
-
Andrew Halaney authored
The property logically makes sense in decimal, and is the standard used elsewhere. Suggested-by:
-
Andrew Halaney authored
As stated at the below link in another review, compatible is always the first property. Follow suit here to avoid copying incorrectly in the future. Link: https://lore.kernel.org/netdev/20230331215804.783439-1-ahalaney@redhat.com/T/#ma76b4116bbb9e49ee4bcf699e40935d80965b3f3Reviewed-by:
-
Bhupesh Sharma authored
As noted by Konrad while reviewing [1], fix the EUD and DWC3 node syntax in sc7280 dtsi file. While at it also fix the errors reported by '$ make dtbs_check' for the EUD node: arch/arm64/boot/dts/qcom/sc7280-crd-r3.dtb: eud@88e0000: ports: 'oneOf' conditional failed, one must be fixed: 'port' is a required property '#address-cells' is a required property '#size-cells' is a required property From schema: Documentation/devicetree/bindings/soc/qcom/qcom,eud.yaml [1]. https://lore.kernel.org/linux-arm-msm/20221231131945.3286639-1-bhupesh.sharma@linaro.orgSigned-off-by:Bhupesh Sharma <bhupesh.sharma@linaro.org> Signed-off-by:
-
Neil Armstrong authored
Introduce sdam_2 node, which is to be used via nvmem for power on reasons during reboot. Add supported PoN reasons supported via sdam_2 node. Signed-off-by:
Neil Armstrong <neil.armstrong@linaro.org> Reviewed-by:
-
Neil Armstrong authored
Introduce sdam_2 node, which is to be used via nvmem for power on reasons during reboot. Add supported PoN reasons supported via sdam_2 node. Signed-off-by:
-
Dmitry Baryshkov authored
Now as both lt9611 and drm/msm drivers were updated to handle the 4k modes over DSI, enable "bonded" DSI mode on DB845c. This way the board utilizes both DSI links and thus can support 4k on the HDMI output. Cc: Amit Pundir <amit.pundir@linaro.org> Signed-off-by:
-
- 23 May, 2023 2 commits
-
-
Bhupesh Sharma authored
Enable the aDSP and cDSP remoteproc nodes on Qualcomm QRB4210 RB2 board. Signed-off-by:
-
Bhupesh Sharma authored
Card-Detect (CD) gpio for SDHC2 is an active GPIO line. Fix the same. This allows the uSD card to be properly detected on the board. Fixes: 8d58a8c0 ("arm64: dts: qcom: Add base qrb4210-rb2 board dts") Reviewed-by:
-
