Saeed Mahameed says:

====================
Mellanox, mlx5 fixes 2019-08-08

This series introduces some fixes to mlx5 driver.

Highlights:
1) From Tariq, Critical mlx5 kTLS fixes to better align with hw specs.
2) From Aya, Fixes to mlx5 tx devlink health reporter.
3) From Maxim, aRFs parsing to use flow dissector to avoid relying on
invalid skb fields.

Please pull and let me know if there is any problem.

For -stable v4.3
 ('net/mlx5e: Only support tx/rx pause setting for port owner')
For -stable v4.9
 ('net/mlx5e: Use flow keys dissector to parse packets for ARFS')
For -stable v5.1
 ('net/mlx5e: Fix false negative indication on tx reporter CQE recovery')
 ('net/mlx5e: Remove redundant check in CQE recovery flow of tx reporter')
 ('net/mlx5e: ethtool, Avoid setting speed to 56GBASE when autoneg off')

Note: when merged with net-next this minor conflict will pop up:
++<<<<<<< (net-next)
 +      if (is_eswitch_flow) {
 +              flow->esw_attr->match_level = match_level;
 +              flow->esw_attr->tunnel_match_level = tunnel_match_level;
++=======
+       if (flow->flags & MLX5E_TC_FLOW_ESWITCH) {
+               flow->esw_attr->inner_match_level = inner_match_level;
+               flow->esw_attr->outer_match_level = outer_match_level;
++>>>>>>> (net)

To resolve, use hunks from net (2nd) and replace:
if (flow->flags & MLX5E_TC_FLOW_ESWITCH)
with
if (is_eswitch_flow)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

ixgbe_service_task() calls unregister_netdev() under rtnl_lock().
But unregister_netdev() internally calls rtnl_lock().
So deadlock would occur.

Fixes: 59dd45d5 ("ixgbe: firmware recovery mode")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Daniel Borkmann says:

====================
Fix collisions in socket cookie generation

This change makes the socket cookie generator as a global counter
instead of per netns in order to fix cookie collisions for BPF use
cases we ran into. See main patch #1 for more details.

Given the change is small/trivial and fixes an issue we're seeing
my preference would be net tree (though it cleanly applies to
net-next as well). Went for net tree instead of bpf tree here given
the main change is in net/core/sock_diag.c, but either way would be
fine with me.

v1 -> v2:
  - Fix up commit description in patch #1, thanks Eric!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull in updates in BPF helper function description.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Generating and retrieving socket cookies are a useful feature that is
exposed to BPF for various program types through bpf_get_socket_cookie()
helper.

The fact that the cookie counter is per netns is quite a limitation
for BPF in practice in particular for programs in host namespace that
use socket cookies as part of a map lookup key since they will be
causing socket cookie collisions e.g. when attached to BPF cgroup hooks
or cls_bpf on tc egress in host namespace handling container traffic
from veth or ipvlan devices with peer in different netns. Change the
counter to be global instead.

Socket cookie consumers must assume the value as opqaue in any case.
Not every socket must have a cookie generated and knowledge of the
counter value itself does not provide much value either way hence
conversion to global is fine.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Martynas Pumputis <m@lambda.lt>
Signed-off-by: David S. Miller <davem@davemloft.net>

David Howells says:

====================
Here's a couple of fixes for rxrpc:

 (1) Fix refcounting of the local endpoint.

 (2) Don't calculate or report packet skew information.  This has been
     obsolete since AFS 3.1 and so is a waste of resources.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Don't bother generating maxSkew in the ACK packet as it has been obsolete
since AFS 3.1.
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Jeffrey Altman <jaltman@auristor.com>

The object lifetime management on the rxrpc_local struct is broken in that
the rxrpc_local_processor() function is expected to clean up and remove an
object - but it may get requeued by packets coming in on the backing UDP
socket once it starts running.

This may result in the assertion in rxrpc_local_rcu() firing because the
memory has been scheduled for RCU destruction whilst still queued:

	rxrpc: Assertion failed
	------------[ cut here ]------------
	kernel BUG at net/rxrpc/local_object.c:468!

Note that if the processor comes around before the RCU free function, it
will just do nothing because ->dead is true.

Fix this by adding a separate refcount to count active users of the
endpoint that causes the endpoint to be destroyed when it reaches 0.

The original refcount can then be used to refcount objects through the work
processor and cause the memory to be rcu freed when that reaches 0.

Fixes: 4f95dd78 ("rxrpc: Rework local endpoint management")
Reported-by: syzbot+1e0edc4b8b7494c28450@syzkaller.appspotmail.com
Signed-off-by: David Howells <dhowells@redhat.com>

As spin_unlock_irq will enable interrupts.
Function tsi108_stat_carry is called from interrupt handler tsi108_irq.
Interrupts are enabled in interrupt handler.
Use spin_lock_irqsave/spin_unlock_irqrestore instead of spin_(un)lock_irq
in IRQ context to avoid this.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We should also enable team's vlan tx offload in hw_enc_features,
pass the vlan packets to the slave devices with vlan tci, let the
slave handle vlan tunneling offload implementation.

Fixes: 3268e5cb ("team: Advertise tunneling offload features")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sk_validate_xmit_skb() and drivers depend on the sk member of
struct sk_buff to identify segments requiring encryption.
Any operation which removes or does not preserve the original TLS
socket such as skb_orphan() or skb_clone() will cause clear text
leaks.

Make the TCP socket underlying an offloaded TLS connection
mark all skbs as decrypted, if TLS TX is in offload mode.
Then in sk_validate_xmit_skb() catch skbs which have no socket
(or a socket with no validation) and decrypted flag set.

Note that CONFIG_SOCK_VALIDATE_XMIT, CONFIG_TLS_DEVICE and
sk->sk_validate_xmit_skb are slightly interchangeable right now,
they all imply TLS offload. The new checks are guarded by
CONFIG_TLS_DEVICE because that's the option guarding the
sk_buff->decrypted member.

Second, smaller issue with orphaning is that it breaks
the guarantee that packets will be delivered to device
queues in-order. All TLS offload drivers depend on that
scheduling property. This means skb_orphan_partial()'s
trick of preserving partial socket references will cause
issues in the drivers. We need a full orphan, and as a
result netem delay/throttling will cause all TLS offload
skbs to be dropped.

Reusing the sk_buff->decrypted flag also protects from
leaking clear text when incoming, decrypted skb is redirected
(e.g. by TC).

See commit 0608c69c ("bpf: sk_msg, sock{map|hash} redirect
through ULP") for justification why the internal flag is safe.
The only location which could leak the flag in is tcp_bpf_sendmsg(),
which is taken care of by clearing the previously unused bit.

v2:
 - remove superfluous decrypted mark copy (Willem);
 - remove the stale doc entry (Boris);
 - rely entirely on EOR marking to prevent coalescing (Boris);
 - use an internal sendpages flag instead of marking the socket
   (Boris).
v3 (Willem):
 - reorganize the can_skb_orphan_partial() condition;
 - fix the flag leak-in through tcp_bpf_sendmsg.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Roman Mashak says:

====================
Fix batched event generation for skbedit action

When adding or deleting a batch of entries, the kernel sends up to
TCA_ACT_MAX_PRIO (defined to 32 in kernel) entries in an event to user
space. However it does not consider that the action sizes may vary and
require different skb sizes.

For example, consider the following script adding 32 entries with all
supported skbedit parameters and cookie (in order to maximize netlink
messages size):

% cat tc-batch.sh
TC="sudo /mnt/iproute2.git/tc/tc"

$TC actions flush action skbedit
for i in `seq 1 $1`;
do
   cmd="action skbedit queue_mapping 2 priority 10 mark 7/0xaabbccdd \
               ptype host inheritdsfield \
               index $i cookie aabbccddeeff112233445566778800a1 "
   args=$args$cmd
done
$TC actions add $args
%
% ./tc-batch.sh 32
Error: Failed to fill netlink attributes while adding TC action.
We have an error talking to the kernel
%

patch 1 adds callback in tc_action_ops of skbedit action, which calculates
the action size, and passes size to tcf_add_notify()/tcf_del_notify().

patch 2 updates the TDC test suite with relevant skbedit test cases.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Update TDC tests with cases varifying ability of TC to install or delete
batches of skbedit actions.
Signed-off-by: Roman Mashak <mrv@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add get_fill_size() routine used to calculate the action size
when building a batch of events.

Fixes: ca9b0e27 ("pkt_action: add new action skbedit")
Signed-off-by: Roman Mashak <mrv@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/net/dsa/sja1105/sja1105_main.c: In function sja1105_fdb_dump:
drivers/net/dsa/sja1105/sja1105_main.c:1226:14: warning:
 variable tx_vid set but not used [-Wunused-but-set-variable]
drivers/net/dsa/sja1105/sja1105_main.c:1226:6: warning:
 variable rx_vid set but not used [-Wunused-but-set-variable]

They are not used since commit 6d7c7d94 ("net: dsa:
sja1105: Fix broken learning with vlan_filtering disabled")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As commit 30d8177e ("bonding: Always enable vlan tx offload")
said, we should always enable bonding's vlan tx offload, pass the
vlan packets to the slave devices with vlan tci, let them to handle
vlan implementation.

Now if encapsulation protocols like VXLAN is used, skb->encapsulation
may be set, then the packet is passed to vlan device which based on
bonding device. However in netif_skb_features(), the check of
hw_enc_features:

	 if (skb->encapsulation)
                 features &= dev->hw_enc_features;

clears NETIF_F_HW_VLAN_CTAG_TX/NETIF_F_HW_VLAN_STAG_TX. This results
in same issue in commit 30d8177e like this:

vlan_dev_hard_start_xmit
  -->dev_queue_xmit
    -->validate_xmit_skb
      -->netif_skb_features //NETIF_F_HW_VLAN_CTAG_TX is cleared
      -->validate_xmit_vlan
        -->__vlan_hwaccel_push_inside //skb->tci is cleared
...
 --> bond_start_xmit
   --> bond_xmit_hash //BOND_XMIT_POLICY_ENCAP34
     --> __skb_flow_dissect // nhoff point to IP header
        -->  case htons(ETH_P_8021Q)
             // skb_vlan_tag_present is false, so
             vlan = __skb_header_pointer(skb, nhoff, sizeof(_vlan),
             //vlan point to ip header wrongly

Fixes: b2a103e6 ("bonding: convert to ndo_fix_features")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In error case, all entries should be freed from the sched list
before deleting it. For simplicity use rcu way.

Fixes: 5a781ccb ("tc: Add support for configuring the taprio scheduler")
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

IPX is no longer supported, but the example in the documentation
might useful. Replace it with IPv6.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Both IPX and TR have not been supported for a while now.
Remove them from the /proc/sys/net documentation.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

At this point nr_frags has been incremented but the frag does not yet
have a page assigned so freeing the skb results in a crash. Reset
nr_frags before freeing the skb to prevent this.
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Before commit d4289fcc ("net: IP6 defrag: use rbtrees for IPv6
defrag"), a netperf UDP_STREAM test[0] using big IPv6 datagrams (thus
generating many fragments) and running over an IPsec tunnel, reported
more than 6Gbps throughput. After that patch, the same test gets only
9Mbps when receiving on a be2net nic (driver can make a big difference
here, for example, ixgbe doesn't seem to be affected).

By reusing the IPv4 defragmentation code, IPv6 lost fragment coalescing
(IPv4 fragment coalescing was dropped by commit 14fe22e3 ("Revert
"ipv4: use skb coalescing in defragmentation"")).

Without fragment coalescing, be2net runs out of Rx ring entries and
starts to drop frames (ethtool reports rx_drops_no_frags errors). Since
the netperf traffic is only composed of UDP fragments, any lost packet
prevents reassembly of the full datagram. Therefore, fragments which
have no possibility to ever get reassembled pile up in the reassembly
queue, until the memory accounting exeeds the threshold. At that point
no fragment is accepted anymore, which effectively discards all
netperf traffic.

When reassembly timeout expires, some stale fragments are removed from
the reassembly queue, so a few packets can be received, reassembled
and delivered to the netperf receiver. But the nic still drops frames
and soon the reassembly queue gets filled again with stale fragments.
These long time frames where no datagram can be received explain why
the performance drop is so significant.

Re-introducing fragment coalescing is enough to get the initial
performances again (6.6Gbps with be2net): driver doesn't drop frames
anymore (no more rx_drops_no_frags errors) and the reassembly engine
works at full speed.

This patch is quite conservative and only coalesces skbs for local
IPv4 and IPv6 delivery (in order to avoid changing skb geometry when
forwarding). Coalescing could be extended in the future if need be, as
more scenarios would probably benefit from it.

[0]: Test configuration
Sender:
ip xfrm policy flush
ip xfrm state flush
ip xfrm state add src fc00:1::1 dst fc00:2::1 proto esp spi 0x1000 aead 'rfc4106(gcm(aes))' 0x0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b 96 mode transport sel src fc00:1::1 dst fc00:2::1
ip xfrm policy add src fc00:1::1 dst fc00:2::1 dir in tmpl src fc00:1::1 dst fc00:2::1 proto esp mode transport action allow
ip xfrm state add src fc00:2::1 dst fc00:1::1 proto esp spi 0x1001 aead 'rfc4106(gcm(aes))' 0x0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b 96 mode transport sel src fc00:2::1 dst fc00:1::1
ip xfrm policy add src fc00:2::1 dst fc00:1::1 dir out tmpl src fc00:2::1 dst fc00:1::1 proto esp mode transport action allow
netserver -D -L fc00:2::1

Receiver:
ip xfrm policy flush
ip xfrm state flush
ip xfrm state add src fc00:2::1 dst fc00:1::1 proto esp spi 0x1001 aead 'rfc4106(gcm(aes))' 0x0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b 96 mode transport sel src fc00:2::1 dst fc00:1::1
ip xfrm policy add src fc00:2::1 dst fc00:1::1 dir in tmpl src fc00:2::1 dst fc00:1::1 proto esp mode transport action allow
ip xfrm state add src fc00:1::1 dst fc00:2::1 proto esp spi 0x1000 aead 'rfc4106(gcm(aes))' 0x0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b 96 mode transport sel src fc00:1::1 dst fc00:2::1
ip xfrm policy add src fc00:1::1 dst fc00:2::1 dir out tmpl src fc00:1::1 dst fc00:2::1 proto esp mode transport action allow
netperf -H fc00:2::1 -f k -P 0 -L fc00:1::1 -l 60 -t UDP_STREAM -I 99,5 -i 5,5 -T5,5 -6
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove check of recovery bit, in the beginning of the CQE recovery
function. This test is already performed right before the reporter
is invoked, when CQE error is detected.

Fixes: de8650a8 ("net/mlx5e: Add tx reporter support")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

CQE recovery function begins with test and set of recovery bit. Add an
error flow which ensures clearing of this bit when leaving the recovery
function, to allow further recoveries to take place. This allows removal
of clearing recovery bit on sq activate.

Fixes: de8650a8 ("net/mlx5e: Add tx reporter support")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Remove wrong error return value when SQ is not in error state.
CQE recovery on TX reporter queries the sq state. If the sq is not in
error state, the sq is either in ready or reset state. Ready state is
good state which doesn't require recovery and reset state is a temporal
state which ends in ready state. With this patch, CQE recovery in this
scenario is successful.

Fixes: de8650a8 ("net/mlx5e: Add tx reporter support")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Shift the tisn field in the WQE control segment, per the
HW specification.

Fixes: d2ead1f3 ("net/mlx5e: Add kTLS TX HW offload support")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Use the proper tisn field name from the union in struct mlx5_wqe_ctrl_seg.

Fixes: d2ead1f3 ("net/mlx5e: Add kTLS TX HW offload support")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

The TLS progress params context WQE should not include an
Eth segment, drop it.
In addition, align the tls_progress_params layout with the
HW specification document:
- fix the tisn field name.
- remove the valid bit.

Fixes: a12ff35e ("net/mlx5: Introduce TLS TX offload hardware bits and structures")
Fixes: d2ead1f3 ("net/mlx5e: Add kTLS TX HW offload support")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Fix the used constants for TLS TIS opmods, per the HW specification.

Fixes: a12ff35e ("net/mlx5: Introduce TLS TX offload hardware bits and structures")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Fix the 128b key offset in key encryption key creation command,
per the HW specification.

Fixes: 45d3b55d ("net/mlx5: Add crypto library to support create/destroy encryption key")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Setting speed to 56GBASE is allowed only with auto-negotiation enabled.

This patch prevent setting speed to 56GBASE when auto-negotiation disabled.

Fixes: f62b8bb8 ("net/mlx5: Extend mlx5_core to support ConnectX-4 Ethernet functionality")
Signed-off-by: Mohamad Heib <mohamadh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Only support changing tx/rx pause frame setting if the net device
is the vport group manager.

Fixes: 3c2d18ef ("net/mlx5e: Support ethtool get/set_pauseparam")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

We have an issue that OVS application creates an offloaded drop rule
that drops VXLAN traffic with both inner and outer header match
criteria. mlx5_core driver detects correctly the inner and outer
header match criteria but does not enable the inner header match criteria
due to an incorrect assumption in mlx5_eswitch_add_offloaded_rule that
only decap rule needs inner header criteria.

Solution:
Remove mlx5_esw_flow_attr's match_level and tunnel_match_level and add
two new members: inner_match_level and outer_match_level.
inner/outer_match_level is set to NONE if the inner/outer match criteria
is not specified in the tc rule creation request. The decap assumption is
removed and the code just needs to check for inner/outer_match_level to
enable the corresponding bit in firmware's match_criteria_enable value.

Fixes: 6363651d ("net/mlx5e: Properly set steering match levels for offloaded TC decap rules")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

The current ARFS code relies on certain fields to be set in the SKB
(e.g. transport_header) and extracts IP addresses and ports by custom
code that parses the packet. The necessary SKB fields, however, are not
always set at that point, which leads to an out-of-bounds access. Use
skb_flow_dissect_flow_keys() to get the necessary information reliably,
fix the out-of-bounds access and reuse the code.

Fixes: 18c908e4 ("net/mlx5e: Add accelerated RFS support")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Simon Wunderlich says:

====================
Here are some batman-adv bugfixes:

 - Fix netlink dumping of all mcast_flags buckets, by Sven Eckelmann

 - Fix deletion of RTR(4|6) mcast list entries, by Sven Eckelmann
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull networking fixes from David Miller:
 "Yeah I should have sent a pull request last week, so there is a lot
  more here than usual:

   1) Fix memory leak in ebtables compat code, from Wenwen Wang.

   2) Several kTLS bug fixes from Jakub Kicinski (circular close on
      disconnect etc.)

   3) Force slave speed check on link state recovery in bonding 802.3ad
      mode, from Thomas Falcon.

   4) Clear RX descriptor bits before assigning buffers to them in
      stmmac, from Jose Abreu.

   5) Several missing of_node_put() calls, mostly wrt. for_each_*() OF
      loops, from Nishka Dasgupta.

   6) Double kfree_skb() in peak_usb can driver, from Stephane Grosjean.

   7) Need to hold sock across skb->destructor invocation, from Cong
      Wang.

   8) IP header length needs to be validated in ipip tunnel xmit, from
      Haishuang Yan.

   9) Use after free in ip6 tunnel driver, also from Haishuang Yan.

  10) Do not use MSI interrupts on r8169 chips before RTL8168d, from
      Heiner Kallweit.

  11) Upon bridge device init failure, we need to delete the local fdb.
      From Nikolay Aleksandrov.

  12) Handle erros from of_get_mac_address() properly in stmmac, from
      Martin Blumenstingl.

  13) Handle concurrent rename vs. dump in netfilter ipset, from Jozsef
      Kadlecsik.

  14) Setting NETIF_F_LLTX on mac80211 causes complete breakage with
      some devices, so revert. From Johannes Berg.

  15) Fix deadlock in rxrpc, from David Howells.

  16) Fix Kconfig deps of enetc driver, we must have PHYLIB. From Yue
      Haibing.

  17) Fix mvpp2 crash on module removal, from Matteo Croce.

  18) Fix race in genphy_update_link, from Heiner Kallweit.

  19) bpf_xdp_adjust_head() stopped working with generic XDP when we
      fixes generic XDP to support stacked devices properly, fix from
      Jesper Dangaard Brouer.

  20) Unbalanced RCU locking in rt6_update_exception_stamp_rt(), from
      David Ahern.

  21) Several memory leaks in new sja1105 driver, from Vladimir Oltean"

* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (214 commits)
  net: dsa: sja1105: Fix memory leak on meta state machine error path
  net: dsa: sja1105: Fix memory leak on meta state machine normal path
  net: dsa: sja1105: Really fix panic on unregistering PTP clock
  net: dsa: sja1105: Use the LOCKEDS bit for SJA1105 E/T as well
  net: dsa: sja1105: Fix broken learning with vlan_filtering disabled
  net: dsa: qca8k: Add of_node_put() in qca8k_setup_mdio_bus()
  net: sched: sample: allow accessing psample_group with rtnl
  net: sched: police: allow accessing police->params with rtnl
  net: hisilicon: Fix dma_map_single failed on arm64
  net: hisilicon: fix hip04-xmit never return TX_BUSY
  net: hisilicon: make hip04_tx_reclaim non-reentrant
  tc-testing: updated vlan action tests with batch create/delete
  net sched: update vlan action for batched events operations
  net: stmmac: tc: Do not return a fragment entry
  net: stmmac: Fix issues when number of Queues >= 4
  net: stmmac: xgmac: Fix XGMAC selftests
  be2net: disable bh with spin_lock in be_process_mcc
  net: cxgb3_main: Fix a resource leak in a error path in 'init_one()'
  net: ethernet: sun4i-emac: Support phy-handle property for finding PHYs
  net: bridge: move default pvid init/deinit to NETDEV_REGISTER/UNREGISTER
  ...

Vladimir Oltean says:

====================
Fixes for SJA1105 DSA: FDBs, Learning and PTP

This is an assortment of functional fixes for the sja1105 switch driver
targeted for the "net" tree (although they apply on net-next just as
well).

Patch 1/5 ("net: dsa: sja1105: Fix broken learning with vlan_filtering
disabled") repairs a breakage introduced in the early development stages
of the driver: support for traffic from the CPU has broken "normal"
frame forwarding (based on DMAC) - there is connectivity through the
switch only because all frames are flooded.
I debated whether this patch qualifies as a fix, since it puts the
switch into a mode it has never operated in before (aka SVL). But
"normal" forwarding did use to work before the "Traffic support for
SJA1105 DSA driver" patchset, and arguably this patch should have been
part of that.
Also, it would be strange for this feature to be broken in the 5.2 LTS.

Patch 2/5 ("net: dsa: sja1105: Use the LOCKEDS bit for SJA1105 E/T as
well") is a simplification of a previous FDB-related patch that is
currently in the 5.3 rc's.

Patches 3/5 - 5/5 fix various crashes found while running linuxptp over the
switch ports for extended periods of time, or in conjunction with other
error conditions. The fixed-up commits were all introduced in 5.2.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

When RX timestamping is enabled and two link-local (non-meta) frames are
received in a row, this constitutes an error.

The tagger is always caching the last link-local frame, in an attempt to
merge it with the meta follow-up frame when that arrives. To recover
from the above error condition, the initial cached link-local frame is
dropped and the second frame in a row is cached (in expectance of the
second meta frame).

However, when dropping the initial link-local frame, its backing memory
was being leaked.

Fixes: f3097be2 ("net: dsa: sja1105: Add a state machine for RX timestamping")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After a meta frame is received, it is associated with the cached
sp->data->stampable_skb from the DSA tagger private structure.

Cached means its refcount is incremented with skb_get() in order for
dsa_switch_rcv() to not free it when the tagger .rcv returns NULL.

The mistake is that skb_unref() is not the correct function to use. It
will correctly decrement the refcount (which will go back to zero) but
the skb memory will not be freed.  That is the job of kfree_skb(), which
also calls skb_unref().

But it turns out that freeing the cached stampable_skb is in fact not
necessary.  It is still a perfectly valid skb, and now it is even
annotated with the partial RX timestamp.  So remove the skb_copy()
altogether and simply pass the stampable_skb with a refcount of 1
(incremented by us, decremented by dsa_switch_rcv) up the stack.

Fixes: f3097be2 ("net: dsa: sja1105: Add a state machine for RX timestamping")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The IS_ERR_OR_NULL(priv->clock) check inside
sja1105_ptp_clock_unregister() is preventing cancel_delayed_work_sync
from actually being run.

Additionally, sja1105_ptp_clock_unregister() does not actually get run,
when placed in sja1105_remove(). The DSA switch gets torn down, but the
sja1105 module does not get unregistered. So sja1105_ptp_clock_unregister
needs to be moved to sja1105_teardown, to be symmetrical with
sja1105_ptp_clock_register which is called from the DSA sja1105_setup.

It is strange to fix a "fixes" patch, but the probe failure can only be
seen when the attached PHY does not respond to MDIO (issue which I can't
pinpoint the reason to) and it goes away after I power-cycle the board.
This time the patch was validated on a failing board, and the kernel
panic from the fixed commit's message can no longer be seen.

Fixes: 29dd908d ("net: dsa: sja1105: Cancel PTP delayed work on unregister")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It looks like the FDB dump taken from first-generation switches also
contains information on whether entries are static or not. So use that
instead of searching through the driver's tables.

Fixes: d7637782 ("net: dsa: sja1105: Implement is_static for FDB entries on E/T")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>