- 30 Nov, 2020 10 commits
-
-
Bjorn Andersson authored
The Lenovo Yoga C630 drives the Boe NV133FHM-N61 eDP display from DSI using a TI SN65DSI86 bridge chip on I2C 10. Define the bridge and eDP panel and enable the display blocks. Tested-by:
Steev Klimaszewski <steev@kali.org> Acked-by:
Shawn Guo <shawn.guo@linaro.org> Link: https://lore.kernel.org/r/20201128034231.89750-1-bjorn.andersson@linaro.orgSigned-off-by:
Bjorn Andersson <bjorn.andersson@linaro.org>
-
Bjorn Andersson authored
The "pins" property takes an array of pin _names_, not pin numbers. Fix this. Tested-by:
-
Bjorn Andersson authored
The numbering of the i2c busses differs from ACPI and a number of typos was made in the original patch. Further more the irq flags for the various resources was not correct and i2c3 only has one of the two client devices active in any one device. Also label the various devices, for easier comparison with the ACPI tables. Tested-by:
-
Ajit Pandey authored
Add the I2S controller node to sc7180 dtsi. Add pinmux for primary and secondary I2S. Reviewed-by:
Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Signed-off-by:
Ajit Pandey <ajitp@codeaurora.org> Signed-off-by:
Cheng-Yi Chiang <cychiang@chromium.org> Signed-off-by:
V Sujith Kumar Reddy <vsujithk@codeaurora.org> Signed-off-by:
Srinivasa Rao Mandadapu <srivasam@codeaurora.org> Link: https://lore.kernel.org/r/1600450426-14063-1-git-send-email-srivasam@codeaurora.orgSigned-off-by:
-
Georgi Djakov authored
Add the interconnects DT property to describe the ports for GENI QUPs on the sdm845 platform. Signed-off-by:
Georgi Djakov <georgi.djakov@linaro.org> Link: https://lore.kernel.org/r/20201105135211.7160-3-georgi.djakov@linaro.orgSigned-off-by:
-
Georgi Djakov authored
The QUP nodes are currently defined just as entries in the topology, but they are not referenced by any of the NoCs. Let's fix this and "attach" them to their NoCs, so that the QUP drivers are able to use them as path endpoints and scale their bandwidth. This is based on the information from the downstream msm-4.9 kernel. Reviewed-by:
-
Georgi Djakov authored
The QUP ports exist in the topology, but are not exposed as an endpoints in DT. Fix this by creating IDs and attach them to their NoCs, so that the various QUP drivers (i2c/spi/uart etc.) are able to request their interconnect paths and scale their bandwidth. Reviewed-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
Bjorn Andersson authored
The LID state can be read from GPIO 124 and the "tablet mode" from GPIO 95, expose these to the system using gpio-keys and mark the falling edge of the LID state as a wakeup-source - to wake the system from suspend. Tested-by:
-
Bjorn Andersson authored
Re-enable the apps_smmu now that the arm-smmu driver supports stream mapping handoff from firmware. Tested-by:
-
Thara Gopinath authored
Add crypto engine (CE) and CE BAM related nodes and definitions to "sdm845.dtsi". Signed-off-by:
Thara Gopinath <thara.gopinath@linaro.org> Link: https://lore.kernel.org/r/20201119155233.3974286-6-thara.gopinath@linaro.org [bjorn: Replaced RPMH_CE_CLK constant, for now] Signed-off-by:
-
- 29 Nov, 2020 1 commit
-
-
Manivannan Sadhasivam authored
Add support for onboard MCP2518FD SPI CAN transceiver attached to SPI0 of RB5. Tested-by:
Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by:
Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Link: https://lore.kernel.org/r/20201127173044.55144-1-manivannan.sadhasivam@linaro.orgSigned-off-by:
-
- 26 Nov, 2020 5 commits
-
-
Alex Elder authored
Use GIC_SPI rather than 0 in the specifiers for the two ARM GIC interrupts used by IPA. Signed-off-by:
Alex Elder <elder@linaro.org> Link: https://lore.kernel.org/r/20201126015457.6557-4-elder@linaro.orgSigned-off-by:
-
Alex Elder authored
Use GIC_SPI rather than 0 in the specifiers for the two ARM GIC interrupts used by IPA. Signed-off-by:
-
Alex Elder authored
Recently we learned that Android and Windows firmware don't seem to like using 3 as an iommu mask value for IPA. A simple fix was to specify exactly the streams needed explicitly, rather than implying a range with the mask. Make the same change for the SC7180 platform. See also: https://lore.kernel.org/linux-arm-msm/20201123052305.157686-1-bjorn.andersson@linaro.org/ Fixes: d82fade8 ("arm64: dts: qcom: sc7180: add IPA information") Reviewed-by:
-
Sai Prakash Ranjan authored
Add coresight components found on Qualcomm Technologies, Inc. SM8150 SoC. Signed-off-by:
Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org> Reviewed-by:
Mathieu Poirier <mathieu.poirier@linaro.org> Link: https://lore.kernel.org/r/20201126052422.24869-1-saiprakash.ranjan@codeaurora.orgSigned-off-by:
-
Matthias Kaehlcke authored
The trogdor design has two options for supplying the 'pp3300_hub' power rail, it can be supplied by 'pp3300_l7c' or 'pp3300_a'. The 'pp3300_a' path includes a load switch that can be controlled through GPIO84. Initially trogdor boards used 'pp3300_l7c' to power the USB hub, newer revisions (will) use 'pp3300_a' as supply for 'pp3300_hub'. Add a DT node for the 'pp3300_a' path and a pinctrl entry for the GPIO. Make this path the default and keep trogdor rev1, lazor rev0 and rev1 on 'pp3300_l7c'. These earlier revisions also allocated the GPIO to the purpose of controlling the power switch, so there is no need to limit the pinctrl config to newer revisions. Remove the platform-wide 'always/boot-on' properties from 'pp3300_l7c' and add them to the boards that use this supply. Also delete the 'always/boot-on' properties of 'pp3300_hub' for these boards. Signed-off-by:
Matthias Kaehlcke <mka@chromium.org> Reviewed-by:
Douglas Anderson <dianders@chromium.org> Link: https://lore.kernel.org/r/20201124164714.v4.1.I0ed4abdd2b2916fbedf76be254bc3457fb8b9655@changeidSigned-off-by:
-
- 24 Nov, 2020 13 commits
-
-
Sibi Sankar authored
Add DDR/L3 bandwidth votes for the pro variant of SC7180 SoC, as it support frequencies upto 2.5 GHz. Reviewed-by:
Sibi Sankar <sibis@codeaurora.org> Link: https://lore.kernel.org/r/1606198876-3515-2-git-send-email-sibis@codeaurora.orgSigned-off-by:
-
Sibi Sankar authored
Tweak the DDR/L3 bandwidth votes on the lite variant of the SC7180 SoC since the gold cores only support frequencies upto 2.1 GHz. Reviewed-by:
-
Terry Hsiao authored
Add a label to the "pen-insert" node in sc7180-trogdor.dtsi Reviewed-by:
Terry Hsiao <terry_hsiao@compal.corp-partner.google.com> Link: https://lore.kernel.org/r/20201116083014.547-1-terry_hsiao@compal.corp-partner.google.comSigned-off-by:
-
Antony Wang authored
Trogdor has a thermistor to monitor the temperature of the charger IC. Add the ADC (monitor) nodes and a thermal zone for this thermistor. Signed-off-by:
Antony Wang <antony_wang@compal.corp-partner.google.com> [mka: tweaked commit message] Signed-off-by:
-
Jishnu Prakash authored
Add ADC_TM peripheral definitions for PM6150 and PM6150L. Add ADC peripheral definition for PM6150l, which is needed for ADC_TM. Signed-off-by:
Jishnu Prakash <jprakash@codeaurora.org> Link: https://lore.kernel.org/r/1602160825-10414-2-git-send-email-jprakash@codeaurora.orgSigned-off-by:
-
Bjorn Andersson authored
The Android and Windows firmware does not accept the use of 3 as a mask to cover the IPA streams. But with 0x721 being related to WiFi and 0x723 being unsed the mapping can be reduced to just cover 0x720 and 0x722, which is accepted. Acked-by:
-
Jonathan Marek authored
Use tabs instead of 6 spaces. Signed-off-by:
Jonathan Marek <jonathan@marek.ca> Link: https://lore.kernel.org/r/20201123144016.19596-1-jonathan@marek.caSigned-off-by:
-
Jonathan Marek authored
Enable the WiFi node and specify its supply regulators. Reviewed-by:
Vinod Koul <vkoul@kernel.org> Signed-off-by:
-
Jonathan Marek authored
Add a node for the WCN3990 WiFi module. Reviewed-by:
-
Bjorn Andersson authored
Point the various remoteprocs of SM8150 MTP to a place with the platform specific firmware. Reviewed-by:
-
Stephen Boyd authored
The SMMU that sits in front of the QUP needs to be programmed properly so that the i2c geni driver can allocate DMA descriptors. Failure to do this leads to faults when using devices such as an i2c touchscreen where the transaction is larger than 32 bytes and we use a DMA buffer. arm-smmu 15000000.iommu: Unexpected global fault, this could be serious arm-smmu 15000000.iommu: GFSR 0x00000002, GFSYNR0 0x00000002, GFSYNR1 0x000006c0, GFSYNR2 0x00000000 Add the right SID and mask so this works. Reviewed-by:
Caleb Connolly <caleb@connolly.tech> Tested-by:
Stephen Boyd <swboyd@chromium.org> [bjorn: Define for second QUP as well, be more specific in sdm845.dtsi] Link: https://lore.kernel.org/r/20201122034149.626045-1-bjorn.andersson@linaro.orgSigned-off-by:
-
Jonathan Marek authored
Fix an error introduced resolving conflicts with camnoc_virt node. Fixes: 0c9dde0d ("arm64: dts: qcom: sm8150: Add secondary USB and PHY nodes") Signed-off-by:
-
Jonathan Marek authored
The uart2 node has been renamed, apply the change to sm8250-hdk dts too so that serial output works. Fixes: 91ed0e90 ("arm64: dts: qcom: add sm8250 hdk dts") Signed-off-by:
-
- 23 Nov, 2020 11 commits
-
-
Matthias Kaehlcke authored
Commit 22337b91 ("arm64: dts: qcom: sc7180: Changed polling mode in Thermal-zones node") sets both 'polling-delay' and 'polling-delay-passive' to zero with the rationale that TSENS interrupts are enabled. A TSENS interrupt fires when the temperature of a thermal zone reaches a trip point, which makes regular polling below the passive trip point temperature unnecessary. However the situation is different when passive cooling is active, regular polling is still needed to trigger a periodic evaluation of the thermal zone by the thermal governor. Change 'polling-delay-passive' back to the original value of 250 ms. Commit 2315ae70 ("arm64: dts: qcom: sc7180: Add gpu cooling support") recently changed the value for the GPU thermal zones from zero to 100 ms, also set it to 250 ms for uniformity. If some zones really need different values these can be changed in dedicated patches. Reviewed-by:
-
Nikita Travkin authored
Some versions of the firmware leave i2c gpios in a wrong state. Add pinctrl that disables pin bias since external pull-up resistors are present. Reviewed-by:
Stephan Gerhold <stephan@gerhold.net> Fixes: 1329c1ab ("arm64: dts: qcom: Add device tree for Samsung Galaxy A3U/A5U") Signed-off-by:
Nikita Travkin <nikitos.tr@gmail.com> Link: https://lore.kernel.org/r/20201113175917.189123-6-nikitos.tr@gmail.comSigned-off-by:
-
Nikita Travkin authored
L8150 uses aw2013 LED contriller for notification LED on the front of the device. Add it to the device tree Reviewed-by:
-
Nikita Travkin authored
L8150 uses SGM3785 Flash LED driver. It is similar to SGM3140 but can also be controlled with PWM. Since SoC doesn't have PWM, add led to the device tree using sgm3140 driver. Reviewed-by:
-
Nikita Travkin authored
L8150 has: - BMC156 accelerometer and magnetic sensor - BMG160 gyroscope sensor Add them to the device tree. Reviewed-by:
-
Nikita Travkin authored
L8150 has RMI4 compatible Synaptics touchscreen on blsp_i2c5. It is powered by fixed regulator. Add both to the device tree. Reviewed-by:
-
Nikita Travkin authored
L8150 has a vibrator connected to PM8916. Add it to the device tree. Reviewed-by:
-
Michael Srba authored
This patch wires up touchscreen support on Samsung Galaxy A3 2015. Reviewed-by:
Michael Srba <Michael.Srba@seznam.cz> Link: https://lore.kernel.org/r/20201115195058.27097-1-michael.srba@seznam.czSigned-off-by:
-
Stephen Boyd authored
There's a proximity sensor on Lazor devices, but only for LTE SKUs. Enable it only on the Lazor LTE SKUs and also configure it properly so it works. Cc: Douglas Anderson <dianders@chromium.org> Cc: Matthias Kaehlcke <mka@chromium.org> Reviewed-by:
-
Stephen Boyd authored
This interrupt has an external pull-up so we don't need to pull it up again. Drop the internal pull here. Note I don't think this really changes anything, just noticed while looking at this irq pin. Reviewed-by:
-
Jonathan Marek authored
Add fastrpc nodes for sDSP, cDSP, and aDSP. Signed-off-by:
-
