Merge tag 'clk-imx-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/abelvesa/linux into clk-imx

Pull i.MX clk driver updates from Abel Vesa:

 - Add the PDM IPC clock for i.MX93
 - Add 519.75MHz frequency support for i.MX9 PLL
 - Simplify the .determine_rate() for GPR mux
 - Make the i.MX8QXP LPCG clock use devm_platform_ioremap_resource
 - Add the audio mux clock to i.MX8
 - Fix the SPLL2 MULT range for PLLv4
 - Update the SPLL2 type in i.MX8ULP
 - Fix the SAI4 clock on i.MX8MP
 - Add silicon revision print for i.MX25 on clocks init
 - Drop the return value from __mx25_clocks_init
 - Fix the clock pauses on no-op set_rate for i.MX8M composite clock
 - Drop restrictions for PLL14xx and fix its max prediv value
 - Drop the 393216000 and 361267200 from PLL14xx rate table to allow
   glitch free switching

* tag 'clk-imx-6.6' of git://git.kernel.org/pub/scm/linux/kernel/git/abelvesa/linux:
  clk: imx: pll14xx: dynamically configure PLL for 393216000/361267200Hz
  clk: imx: pll14xx: align pdiv with reference manual
  clk: imx: composite-8m: fix clock pauses when set_rate would be a no-op
  clk: imx25: make __mx25_clocks_init return void
  clk: imx25: print silicon revision during init
  dt-bindings: clocks: imx8mp: make sai4 a dummy clock
  clk: imx8mp: fix sai4 clock
  clk: imx: imx8ulp: update SPLL2 type
  clk: imx: pllv4: Fix SPLL2 MULT range
  clk: imx: imx8: add audio clock mux driver
  dt-bindings: clock: fsl,imx8-acm: Add audio clock mux support
  clk: imx: clk-imx8qxp-lpcg: Convert to devm_platform_ioremap_resource()
  clk: imx: clk-gpr-mux: Simplify .determine_rate()
  clk: imx: Add 519.75MHz frequency support for imx9 pll
  clk: imx93: Add PDM IPG clk
  dt-bindings: clock: imx93: Add PDM IPG clk

Since commit b09c68dc ("clk: imx: pll14xx: Support dynamic rates"),
the driver has the ability to dynamically compute PLL parameters to
approximate the requested rates. This is not always used, because the
logic is as follows:

  - Check if the target rate is hardcoded in the frequency table
  - Check if varying only kdiv is possible, so switch over is glitch free
  - Compute rate dynamically by iterating over pdiv range

If we skip the frequency table for the 1443x PLL, we find that the
computed values differ to the hardcoded ones. This can be valid if the
hardcoded values guarantee for example an earlier lock-in or if the
divisors are chosen, so that other important rates are more likely to
be reached glitch-free.

For rates (393216000 and 361267200, this doesn't seem to be the case:
They are only approximated by existing parameters (393215995 and
361267196 Hz, respectively) and they aren't reachable glitch-free from
other hardcoded frequencies. Dropping them from the table allows us
to lock-in to these frequencies exactly.

This is immediately noticeable because they are the assigned-clock-rates
for IMX8MN_AUDIO_PLL1 and IMX8MN_AUDIO_PLL2, respectively and a look
into clk_summary so far showed that they were a few Hz short of the target:

imx8mn-board:~# grep audio_pll[12]_out /sys/kernel/debug/clk/clk_summary
audio_pll2_out           0        0        0   361267196 0     0  50000   N
audio_pll1_out           1        1        0   393215995 0     0  50000   Y

and afterwards:

imx8mn-board:~# grep audio_pll[12]_out /sys/kernel/debug/clk/clk_summary
audio_pll2_out           0        0        0   361267200 0     0  50000   N
audio_pll1_out           1        1        0   393216000 0     0  50000   Y

This change is equivalent to adding following hardcoded values:

  /*               rate     mdiv  pdiv  sdiv   kdiv */
  PLL_1443X_RATE(393216000, 655,    5,    3,  23593),
  PLL_1443X_RATE(361267200, 497,   33,    0, -16882),

Fixes: 053a4ffe ("clk: imx: imx8mm: fix audio pll setting")
Cc: stable@vger.kernel.org # v5.18+
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Link: https://lore.kernel.org/r/20230807084744.1184791-2-m.felsch@pengutronix.deSigned-off-by: Abel Vesa <abel.vesa@linaro.org>

The PLL14xx hardware can be found on i.MX8M{M,N,P} SoCs and always come
with a 6-bit pre-divider. Neither the reference manuals nor the
datasheets of these SoCs do mention any restrictions. Furthermore the
current code doesn't respect the restrictions from the comment too.

Therefore drop the restriction and align the max pre-divider (pdiv)
value to 63 to get more accurate frequencies.

Fixes: b09c68dc ("clk: imx: pll14xx: Support dynamic rates")
Cc: stable@vger.kernel.org
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Link: https://lore.kernel.org/r/20230807084744.1184791-1-m.felsch@pengutronix.deSigned-off-by: Abel Vesa <abel.vesa@linaro.org>

Reconfiguring the clock divider to the exact same value is observed
on an i.MX8MN to often cause a longer than usual clock pause, probably
because the divider restarts counting whenever the register is rewritten.

This issue doesn't show up normally, because the clock framework will
take care to not call set_rate when the clock rate is the same.
However, when we reconfigure an upstream clock, the common code will
call set_rate with the newly calculated rate on all children, e.g.:

  - sai5 is running normally and divides Audio PLL out by 16.
  - Audio PLL rate is increased by 32Hz (glitch-free kdiv change)
  - rates for children are recalculated and rates are set recursively
  - imx8m_clk_composite_divider_set_rate(sai5) is called with
    32/16 = 2Hz more
  - imx8m_clk_composite_divider_set_rate computes same divider as before
  - divider register is written, so it restarts counting from zero and
    MCLK is briefly paused, so instead of e.g. 40ns, MCLK is low for 120ns.

Some external clock consumers can be upset by such unexpected clock pauses,
so let's make sure we only rewrite the divider value when the value to be
written is actually different.

Fixes: d3ff9728 ("clk: imx: Add imx composite clock")
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20230807082201.2332746-1-a.fatoum@pengutronix.deSigned-off-by: Abel Vesa <abel.vesa@linaro.org>

The __mx25_clocks_init function always returns 0 and its only
caller does not check the return value. Let's remove it.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20230802184046.153394-3-martin@kaiser.cxSigned-off-by: Abel Vesa <abel.vesa@linaro.org>

Print the imx25 silicon revision when the clocks are initialised.

Use the same mechanism as for imx27, i.e. call mx25_revision.
This function is unused at the moment.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20230802184046.153394-2-martin@kaiser.cxSigned-off-by: Abel Vesa <abel.vesa@linaro.org>

The hardware don't have a SAI4 instance so remove the define. Use a
comment to keep it as reference and to avoid confusion.

Fixes: 10886914 ("dt-bindings: imx: Add clock binding doc for i.MX8MP")
Acked-by: Stephen Boyd <sboyd@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Link: https://lore.kernel.org/r/20230731142150.3186650-2-m.felsch@pengutronix.deSigned-off-by: Abel Vesa <abel.vesa@linaro.org>

The reference manual don't mention a SAI4 hardware block. This would be
clock slice 78 which is skipped (TRM, page 237). Remove any reference to
this clock to align the driver with the reality.

Fixes: 9c140d99 ("clk: imx: Add support for i.MX8MP clock driver")
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Link: https://lore.kernel.org/r/20230731142150.3186650-1-m.felsch@pengutronix.deSigned-off-by: Abel Vesa <abel.vesa@linaro.org>

The SPLL2 on iMX8ULP is different with other frac PLLs, it can
support VCO from 650Mhz to 1Ghz. Following the changes to pllv4,
use the new type IMX_PLLV4_IMX8ULP_1GHZ.

Fixes: c43a801a ("clk: imx: Add clock driver for imx8ulp")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20230625123340.4067536-2-peng.fan@oss.nxp.comSigned-off-by: Abel Vesa <abel.vesa@linaro.org>

The SPLL2 on iMX8ULP is different with other frac PLLs, it can
support VCO from 650Mhz to 1Ghz. According to RM, the MULT is
using a range from 27 to 54, not some fixed values. If using
current PLL implementation, some clock rate can't be supported.

Fix the issue by adding new type for the SPLL2 and use MULT range
to replace MULT table

Fixes: 5f0601c4 ("clk: imx: Update the pllv4 to support imx8ulp")
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20230625123340.4067536-1-peng.fan@oss.nxp.comSigned-off-by: Abel Vesa <abel.vesa@linaro.org>

The Audio Clock Mux (ACM) is a collection of control registers
and multiplexers that are used to route the audio source clocks
to the audio peripherals.

Each audio peripheral has its dedicated audio clock mux
(which differ based on usage) and control register.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/1690260984-25744-3-git-send-email-shengjiu.wang@nxp.comSigned-off-by: Abel Vesa <abel.vesa@linaro.org>

Add the clock dt-binding file for Audio Clock Mux. which
is the IP for i.MX8QM, i.MX8QXP, i.MX8DXL.

Add the clockid for clocks in header file.

The Audio Clock Mux is binded with all the audio IP and audio clocks
in the subsystem, so need to list the power domain of related clocks
and IPs. Each clock and IP has a power domain, so there are so many
power domains.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/1690260984-25744-2-git-send-email-shengjiu.wang@nxp.comSigned-off-by: Abel Vesa <abel.vesa@linaro.org>

Use devm_platform_ioremap_resource() to simplify code.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20230705065313.67043-8-frank.li@vivo.comSigned-off-by: Abel Vesa <abel.vesa@linaro.org>

imx_clk_gpr_mux_determine_rate() is the same as __clk_mux_determine_rate(),
so use the latter to save some LoC.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/ac8bd50c41b84f244bb0ec94e8aed25c513c9037.1688760152.git.christophe.jaillet@wanadoo.frSigned-off-by: Abel Vesa <abel.vesa@linaro.org>

For video pll, it may need 519.75MHz clock frequency for
the LVDS display usage. So add 519.75MHz frequency config
support for video pll.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20230628061724.2056520-3-ping.bai@nxp.comSigned-off-by: Abel Vesa <abel.vesa@linaro.org>

The IPG clk and MCLK of PDM share the same control gate.
Reviewed-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Chancel Liu <chancel.liu@nxp.com>
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20230628061724.2056520-2-ping.bai@nxp.comSigned-off-by: Abel Vesa <abel.vesa@linaro.org>

Add PDM IPG clk.
Reviewed-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Chancel Liu <chancel.liu@nxp.com>
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230628061724.2056520-1-ping.bai@nxp.comSigned-off-by: Abel Vesa <abel.vesa@linaro.org>

We just sorted the entries and fields last release, so just out of a
perverse sense of curiosity, I decided to see if we can keep things
ordered for even just one release.

The answer is "No. No we cannot".

I suggest that all kernel developers will need weekly training sessions,
involving a lot of Big Bird and Sesame Street.  And at the yearly
maintainer summit, we will all sing the alphabet song together.

I doubt I will keep doing this.  At some point "perverse sense of
curiosity" turns into just a cold dark place filled with sadness and
despair.

Repeats: 80e62bc8 ("MAINTAINERS: re-sort all entries and fields")
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull dma-mapping fixes from Christoph Hellwig:

 - swiotlb area sizing fixes (Petr Tesarik)

* tag 'dma-mapping-6.5-2023-07-09' of git://git.infradead.org/users/hch/dma-mapping:
  swiotlb: reduce the number of areas to match actual memory pool size
  swiotlb: always set the number of areas before allocating the pool

Pull irq update from Borislav Petkov:

 - Optimize IRQ domain's name assignment

* tag 'irq_urgent_for_v6.5_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqdomain: Use return value of strreplace()

Pull x86 fpu fix from Borislav Petkov:

 - Do FPU AP initialization on Xen PV too which got missed by the recent
   boot reordering work

* tag 'x86_urgent_for_v6.5_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/xen: Fix secondary processors' FPU initialization

Pull x86 fix from Thomas Gleixner:
 "A single fix for the mechanism to park CPUs with an INIT IPI.

  On shutdown or kexec, the kernel tries to park the non-boot CPUs with
  an INIT IPI. But the same code path is also used by the crash utility.
  If the CPU which panics is not the boot CPU then it sends an INIT IPI
  to the boot CPU which resets the machine.

  Prevent this by validating that the CPU which runs the stop mechanism
  is the boot CPU. If not, leave the other CPUs in HLT"

* tag 'x86-core-2023-07-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/smp: Don't send INIT to boot CPU

Pull MIPS fixes from Thomas Bogendoerfer:

 - fixes for KVM

 - fix for loongson build and cpu probing

 - DT fixes

* tag 'mips_6.5_1' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
  MIPS: kvm: Fix build error with KVM_MIPS_DEBUG_COP0_COUNTERS enabled
  MIPS: dts: add missing space before {
  MIPS: Loongson: Fix build error when make modules_install
  MIPS: KVM: Fix NULL pointer dereference
  MIPS: Loongson: Fix cpu_probe_loongson() again

Pull xfs fix from Darrick Wong:
 "Nothing exciting here, just getting rid of a gcc warning that I got
  tired of seeing when I turn on gcov"

* tag 'xfs-6.5-merge-6' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
  xfs: fix uninit warning in xfs_growfs_data

Pull more smb client updates from Steve French:

 - fix potential use after free in unmount

 - minor cleanup

 - add worker to cleanup stale directory leases

* tag '6.5-rc-smb3-client-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: Add a laundromat thread for cached directories
  smb: client: remove redundant pointer 'server'
  cifs: fix session state transition to avoid use-after-free issue

Pull NTB updates from Jon Mason:
 "Fixes for pci_clean_master, error handling in driver inits, and
  various other issues/bugs"

* tag 'ntb-6.5' of https://github.com/jonmason/ntb:
  ntb: hw: amd: Fix debugfs_create_dir error checking
  ntb.rst: Fix copy and paste error
  ntb_netdev: Fix module_init problem
  ntb: intel: Remove redundant pci_clear_master
  ntb: epf: Remove redundant pci_clear_master
  ntb_hw_amd: Remove redundant pci_clear_master
  ntb: idt: drop redundant pci_enable_pcie_error_reporting()
  MAINTAINERS: git://github -> https://github.com for jonmason
  NTB: EPF: fix possible memory leak in pci_vntb_probe()
  NTB: ntb_tool: Add check for devm_kcalloc
  NTB: ntb_transport: fix possible memory leak while device_register() fails
  ntb: intel: Fix error handling in intel_ntb_pci_driver_init()
  NTB: amd: Fix error handling in amd_ntb_pci_driver_init()
  ntb: idt: Fix error handling in idt_pci_driver_init()

Lockdep is certainly right to complain about

  (&vma->vm_lock->lock){++++}-{3:3}, at: vma_start_write+0x2d/0x3f
                 but task is already holding lock:
  (&mapping->i_mmap_rwsem){+.+.}-{3:3}, at: mmap_region+0x4dc/0x6db

Invert those to the usual ordering.

Fixes: 33313a74 ("mm: lock newly mapped VMA which can be modified after it becomes visible")
Cc: stable@vger.kernel.org
Signed-off-by: Hugh Dickins <hughd@google.com>
Tested-by: Suren Baghdasaryan <surenb@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge tag 'mm-hotfixes-stable-2023-07-08-10-43' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm

Pull hotfixes from Andrew Morton:
 "16 hotfixes. Six are cc:stable and the remainder address post-6.4
  issues"

The merge undoes the disabling of the CONFIG_PER_VMA_LOCK feature, since
it was all hopefully fixed in mainline.

* tag 'mm-hotfixes-stable-2023-07-08-10-43' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
  lib: dhry: fix sleeping allocations inside non-preemptable section
  kasan, slub: fix HW_TAGS zeroing with slub_debug
  kasan: fix type cast in memory_is_poisoned_n
  mailmap: add entries for Heiko Stuebner
  mailmap: update manpage link
  bootmem: remove the vmemmap pages from kmemleak in free_bootmem_page
  MAINTAINERS: add linux-next info
  mailmap: add Markus Schneider-Pargmann
  writeback: account the number of pages written back
  mm: call arch_swap_restore() from do_swap_page()
  squashfs: fix cache race with migration
  mm/hugetlb.c: fix a bug within a BUG(): inconsistent pte comparison
  docs: update ocfs2-devel mailing list address
  MAINTAINERS: update ocfs2-devel mailing list address
  mm: disable CONFIG_PER_VMA_LOCK until its fixed
  fork: lock VMAs of the parent process when forking

When forking a child process, the parent write-protects anonymous pages
and COW-shares them with the child being forked using copy_present_pte().

We must not take any concurrent page faults on the source vma's as they
are being processed, as we expect both the vma and the pte's behind it
to be stable.  For example, the anon_vma_fork() expects the parents
vma->anon_vma to not change during the vma copy.

A concurrent page fault on a page newly marked read-only by the page
copy might trigger wp_page_copy() and a anon_vma_prepare(vma) on the
source vma, defeating the anon_vma_clone() that wasn't done because the
parent vma originally didn't have an anon_vma, but we now might end up
copying a pte entry for a page that has one.

Before the per-vma lock based changes, the mmap_lock guaranteed
exclusion with concurrent page faults.  But now we need to do a
vma_start_write() to make sure no concurrent faults happen on this vma
while it is being processed.

This fix can potentially regress some fork-heavy workloads.  Kernel
build time did not show noticeable regression on a 56-core machine while
a stress test mapping 10000 VMAs and forking 5000 times in a tight loop
shows ~5% regression.  If such fork time regression is unacceptable,
disabling CONFIG_PER_VMA_LOCK should restore its performance.  Further
optimizations are possible if this regression proves to be problematic.
Suggested-by: David Hildenbrand <david@redhat.com>
Reported-by: Jiri Slaby <jirislaby@kernel.org>
Closes: https://lore.kernel.org/all/dbdef34c-3a07-5951-e1ae-e9c6e3cdf51b@kernel.org/Reported-by: Holger Hoffstätte <holger@applied-asynchrony.com>
Closes: https://lore.kernel.org/all/b198d649-f4bf-b971-31d0-e8433ec2a34c@applied-asynchrony.com/Reported-by: Jacob Young <jacobly.alt@gmail.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=217624
Fixes: 0bff0aae ("x86/mm: try VMA lock-based page fault handling first")
Cc: stable@vger.kernel.org
Signed-off-by: Suren Baghdasaryan <surenb@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

mmap_region adds a newly created VMA into VMA tree and might modify it
afterwards before dropping the mmap_lock.  This poses a problem for page
faults handled under per-VMA locks because they don't take the mmap_lock
and can stumble on this VMA while it's still being modified.  Currently
this does not pose a problem since post-addition modifications are done
only for file-backed VMAs, which are not handled under per-VMA lock.
However, once support for handling file-backed page faults with per-VMA
locks is added, this will become a race.

Fix this by write-locking the VMA before inserting it into the VMA tree.
Other places where a new VMA is added into VMA tree do not modify it
after the insertion, so do not need the same locking.

Cc: stable@vger.kernel.org
Signed-off-by: Suren Baghdasaryan <surenb@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

With recent changes necessitating mmap_lock to be held for write while
expanding a stack, per-VMA locks should follow the same rules and be
write-locked to prevent page faults into the VMA being expanded. Add
the necessary locking.

Cc: stable@vger.kernel.org
Signed-off-by: Suren Baghdasaryan <surenb@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull more SCSI updates from James Bottomley:
 "A few late arriving patches that missed the initial pull request. It's
  mostly bug fixes (the dt-bindings is a fix for the initial pull)"

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: ufs: core: Remove unused function declaration
  scsi: target: docs: Remove tcm_mod_builder.py
  scsi: target: iblock: Quiet bool conversion warning with pr_preempt use
  scsi: dt-bindings: ufs: qcom: Fix ICE phandle
  scsi: core: Simplify scsi_cdl_check_cmd()
  scsi: isci: Fix comment typo
  scsi: smartpqi: Replace one-element arrays with flexible-array members
  scsi: target: tcmu: Replace strlcpy() with strscpy()
  scsi: ncr53c8xx: Replace strlcpy() with strscpy()
  scsi: lpfc: Fix lpfc_name struct packing

Pull more i2c updates from Wolfram Sang:

 - xiic patch should have been in the original pull but slipped through

 - mpc patch fixes a build regression

 - nomadik cleanup

* tag 'i2c-for-6.5-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: mpc: Drop unused variable
  i2c: nomadik: Remove a useless call in the remove function
  i2c: xiic: Don't try to handle more interrupt events after error

Pull hardening fixes from Kees Cook:

 - Check for NULL bdev in LoadPin (Matthias Kaehlcke)

 - Revert unwanted KUnit FORTIFY build default

 - Fix 1-element array causing boot warnings with xhci-hub

* tag 'hardening-v6.5-rc1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
  usb: ch9: Replace bmSublinkSpeedAttr 1-element array with flexible array
  Revert "fortify: Allow KUnit test to build without FORTIFY"
  dm: verity-loadpin: Add NULL pointer check for 'bdev' parameter

The debugfs_create_dir function returns ERR_PTR in case of error, and the
only correct way to check if an error occurred is 'IS_ERR' inline function.
This patch will replace the null-comparison with IS_ERR.
Signed-off-by: Anup Sharma <anupnewsmail@gmail.com>
Suggested-by: Ivan Orlov <ivan.orlov0322@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>

Merge tag 'perf-tools-for-v6.5-2-2023-07-06' of git://git.kernel.org/pub/scm/linux/kernel/git/perf/perf-tools-next

Pull more perf tools updates from Namhyung Kim:
 "These are remaining changes and fixes for this cycle.

  Build:

   - Allow generating vmlinux.h from BTF using `make GEN_VMLINUX_H=1`
     and skip if the vmlinux has no BTF.

   - Replace deprecated clang -target xxx option by --target=xxx.

  perf record:

   - Print event attributes with well known type and config symbols in
     the debug output like below:

       # perf record -e cycles,cpu-clock -C0 -vv true
       <SNIP>
       ------------------------------------------------------------
       perf_event_attr:
         type                             0 (PERF_TYPE_HARDWARE)
         size                             136
         config                           0 (PERF_COUNT_HW_CPU_CYCLES)
         { sample_period, sample_freq }   4000
         sample_type                      IP|TID|TIME|CPU|PERIOD|IDENTIFIER
         read_format                      ID
         disabled                         1
         inherit                          1
         freq                             1
         sample_id_all                    1
         exclude_guest                    1
       ------------------------------------------------------------
       sys_perf_event_open: pid -1  cpu 0  group_fd -1  flags 0x8 = 5
       ------------------------------------------------------------
       perf_event_attr:
         type                             1 (PERF_TYPE_SOFTWARE)
         size                             136
         config                           0 (PERF_COUNT_SW_CPU_CLOCK)
         { sample_period, sample_freq }   4000
         sample_type                      IP|TID|TIME|CPU|PERIOD|IDENTIFIER
         read_format                      ID
         disabled                         1
         inherit                          1
         freq                             1
         sample_id_all                    1
         exclude_guest                    1

   - Update AMD IBS event error message since it now support per-process
     profiling but no priviledge filters.

       $ sudo perf record -e ibs_op//k -C 0
       Error:
       AMD IBS doesn't support privilege filtering. Try again without
       the privilege modifiers (like 'k') at the end.

  perf lock contention:

   - Support CSV style output using -x option

       $ sudo perf lock con -ab -x, sleep 1
       # output: contended, total wait, max wait, avg wait, type, caller
       19, 194232, 21415, 10222, spinlock, process_one_work+0x1f0
       15, 162748, 23843, 10849, rwsem:R, do_user_addr_fault+0x40e
       4, 86740, 23415, 21685, rwlock:R, ep_poll_callback+0x2d
       1, 84281, 84281, 84281, mutex, iwl_mvm_async_handlers_wk+0x135
       8, 67608, 27404, 8451, spinlock, __queue_work+0x174
       3, 58616, 31125, 19538, rwsem:W, do_mprotect_pkey+0xff
       3, 52953, 21172, 17651, rwlock:W, do_epoll_wait+0x248
       2, 30324, 19704, 15162, rwsem:R, do_madvise+0x3ad
       1, 24619, 24619, 24619, spinlock, rcu_core+0xd4

   - Add --output option to save the data to a file not to be interfered
     by other debug messages.

  Test:

   - Fix event parsing test on ARM where there's no raw PMU nor supports
     PERF_PMU_CAP_EXTENDED_HW_TYPE.

   - Update the lock contention test case for CSV output.

   - Fix a segfault in the daemon command test.

  Vendor events (JSON):

   - Add has_event() to check if the given event is available on system
     at runtime. On Intel machines, some transaction events may not be
     present when TSC extensions are disabled.

   - Update Intel event metrics.

  Misc:

   - Sort symbols by name using an external array of pointers instead of
     a rbtree node in the symbol. This will save 16-bytes or 24-bytes
     per symbol whether the sorting is actually requested or not.

   - Fix unwinding DWARF callstacks using libdw when --symfs option is
     used"

* tag 'perf-tools-for-v6.5-2-2023-07-06' of git://git.kernel.org/pub/scm/linux/kernel/git/perf/perf-tools-next: (38 commits)
  perf test: Fix event parsing test when PERF_PMU_CAP_EXTENDED_HW_TYPE isn't supported.
  perf test: Fix event parsing test on Arm
  perf evsel amd: Fix IBS error message
  perf: unwind: Fix symfs with libdw
  perf symbol: Fix uninitialized return value in symbols__find_by_name()
  perf test: Test perf lock contention CSV output
  perf lock contention: Add --output option
  perf lock contention: Add -x option for CSV style output
  perf lock: Remove stale comments
  perf vendor events intel: Update tigerlake to 1.13
  perf vendor events intel: Update skylakex to 1.31
  perf vendor events intel: Update skylake to 57
  perf vendor events intel: Update sapphirerapids to 1.14
  perf vendor events intel: Update icelakex to 1.21
  perf vendor events intel: Update icelake to 1.19
  perf vendor events intel: Update cascadelakex to 1.19
  perf vendor events intel: Update meteorlake to 1.03
  perf vendor events intel: Add rocketlake events/metrics
  perf vendor metrics intel: Make transaction metrics conditional
  perf jevents: Support for has_event function
  ...

Pull bitmap updates from Yury Norov:
 "Fixes for different bitmap pieces:

   - lib/test_bitmap: increment failure counter properly

     The tests that don't use expect_eq() macro to determine that a test
     is failured must increment failed_tests explicitly.

   - lib/bitmap: drop optimization of bitmap_{from,to}_arr64

     bitmap_{from,to}_arr64() optimization is overly optimistic
     on 32-bit LE architectures when it's wired to
     bitmap_copy_clear_tail().

   - nodemask: Drop duplicate check in for_each_node_mask()

     As the return value type of first_node() became unsigned, the node
     >= 0 became unnecessary.

   - cpumask: fix function description kernel-doc notation

   - MAINTAINERS: Add bits.h and bitfield.h to the BITMAP API record

     Add linux/bits.h and linux/bitfield.h for visibility"

* tag 'bitmap-6.5-rc1' of https://github.com/norov/linux:
  MAINTAINERS: Add bitfield.h to the BITMAP API record
  MAINTAINERS: Add bits.h to the BITMAP API record
  cpumask: fix function description kernel-doc notation
  nodemask: Drop duplicate check in for_each_node_mask()
  lib/bitmap: drop optimization of bitmap_{from,to}_arr64
  lib/test_bitmap: increment failure counter properly

The Smatch static checker reports the following warnings:

    lib/dhry_run.c:38 dhry_benchmark() warn: sleeping in atomic context
    lib/dhry_run.c:43 dhry_benchmark() warn: sleeping in atomic context

Indeed, dhry() does sleeping allocations inside the non-preemptable
section delimited by get_cpu()/put_cpu().

Fix this by using atomic allocations instead.
Add error handling, as atomic these allocations may fail.

Link: https://lkml.kernel.org/r/bac6d517818a7cd8efe217c1ad649fffab9cc371.1688568764.git.geert+renesas@glider.be
Fixes: 13684e96 ("lib: dhry: fix unstable smp_processor_id(_) usage")
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/r/0469eb3a-02eb-4b41-b189-de20b931fa56@moroto.mountainSigned-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

Commit 946fa0db ("mm/slub: extend redzone check to extra allocated
kmalloc space than requested") added precise kmalloc redzone poisoning to
the slub_debug functionality.

However, this commit didn't account for HW_TAGS KASAN fully initializing
the object via its built-in memory initialization feature.  Even though
HW_TAGS KASAN memory initialization contains special memory initialization
handling for when slub_debug is enabled, it does not account for in-object
slub_debug redzones.  As a result, HW_TAGS KASAN can overwrite these
redzones and cause false-positive slub_debug reports.

To fix the issue, avoid HW_TAGS KASAN memory initialization when
slub_debug is enabled altogether.  Implement this by moving the
__slub_debug_enabled check to slab_post_alloc_hook.  Common slab code
seems like a more appropriate place for a slub_debug check anyway.

Link: https://lkml.kernel.org/r/678ac92ab790dba9198f9ca14f405651b97c8502.1688561016.git.andreyknvl@google.com
Fixes: 946fa0db ("mm/slub: extend redzone check to extra allocated kmalloc space than requested")
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Reported-by: Will Deacon <will@kernel.org>
Acked-by: Marco Elver <elver@google.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Hyeonggon Yoo <42.hyeyoo@gmail.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: kasan-dev@googlegroups.com
Cc: Pekka Enberg <penberg@kernel.org>
Cc: Peter Collingbourne <pcc@google.com>
Cc: Roman Gushchin <roman.gushchin@linux.dev>
Cc: Vincenzo Frascino <vincenzo.frascino@arm.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>