This patch adds runtime power management support for otg fsm mode, since
A-device in a_idle state cannot detect data pulse irq after suspended, here
enable wakeup by connection before suspend to make it can be resumed by DP;
and handle wakeup from that state like SRP.
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

If CI_HDRC_TURN_VBUS_EARLY_ON is set, turn on vbus before adding hcd, so it
will not set reg_vbus of ehci_ci_priv, then vbus will not be handled by ehci core.
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Some usb PHYs need power supply from vbus to make it work, eg mxs-phy, if
there is no vbus, USB PHY will not in correct state when the controller starts
to work, for host, this requires vbus should be turned on before setting port
power(PP) of ehci, to work with this kind of USB PHY design, this patch adds
a flag CI_HDRC_TURN_VBUS_EARLY_ON, can be checked by host driver to turn on
vbus while start host.
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Since PHY for ChipIdea is optional (not all SoCs having PHY for ChipIdea should
be programmed), we register 'nop' PHY for platforms that do not have
programmable PHY.
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

For chipidea, its resume sequence is not-EHCI compatible, see
below description for FPR at portsc. So in order to send SoF in
time for remote wakeup sequence(within 3ms), the RUN/STOP bit must
be set before the resume signal is ended, but the usb resume
code may run after resume signal is ended, so we had to set it
at suspend path.

Force Port Resume - RW. Default = 0b.
1= Resume detected/driven on port.
0=No resume (K-state) detected/driven on port.
Host mode:
Software sets this bit to one to drive resume signaling. The Controller sets this bit to '1' if
a J-to-K transition is detected while the port is in the Suspend state. When this bit
transitions to a '1' because a J-to-K transition is detected, the Port Change Detect bit in
the USBSTS register is also set to '1'. This bit will automatically change to '0' after the
resume sequence is complete. This behavior is different from EHCI where the controller
driver is required to set this bit to a '0' after the resume duration is timed in the driver.
Note that when the controller owns the port, the resume sequence follows the defined

sequence documented in the USB Specification Revision 2.0. The resume signaling
(Full-speed 'K') is driven on the port as long as this bit remains a '1'. This bit will remain
a '1' until the port has switched to idle. Writing a '0' has no affect because the port
controller will time the resume operation, clear the bit and the port control state switches
to HS or FS idle.
This field is '0' if Port Power(PP) is '0' in host mode.

This bit is not-EHCI compatible.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Chipidea: Set connect-at-fullspeed bit when entering host mode if CI_HDRC_FORCE_FULLSPEED is set in the platform data

PORTSC_PFSC is not set on entering host mode which means the USB OTG
controller will attempt to enumerate USB devices at high speed even when the
CI_HDRC_FORCE_FULLSPEED flag is set in the platform data.

This patch ensures it is set right before host mode operations begin if needed.
Signed-off-by: Daniel Tang <dt.tangr@gmail.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: Daniel Tang <dt.tangr@gmail.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

At chipidea revision 2.40a, there is a below errata:

9000531823  B2-Medium  Adding a dTD to a Primed Endpoint May Not Get Recognized

Title: Adding a dTD to a Primed Endpoint May Not Get Recognized

Impacted Configuration: All device mode configurations.

Description:
There is an issue with the add dTD tripwire semaphore (ATDTW bit in USBCMD register)
that can cause the controller to ignore a dTD that is added to a primed endpoint.
When this happens, the software can read the tripwire bit and the status bit at '1'
even though the endpoint is unprimed.

After executing a dTD, the device controller endpoint state machine executes a final
read of the dTD terminate bit to check if the application added a dTD to the linked
list at the last moment. This read is done in the finpkt_read_latest_next_td (44) state.
After the read is performed, if the terminate bit is still set, the state machine moves
to unprime the endpoint. The decision to unprime the endpoint is done in the
checkqh_decision (59) state, based on the value of the terminate bit.
Before reaching the checkqh_decision state, the state machine traverses the
writeqhtd_status (57), writeqh_status (56), and release_prime_mask (42) states.
As shown in the waveform, the ep_addtd_tripwire_clr signal is not set to clear
the tripwire bit in these states.

Workaround:
The software must implement a periodic poll cycle, and check for each dTD
pending on execution (Active = 1), if the enpoint is primed. It can do this by reading
the corresponding bits in the ENDPTPRIME and ENDPTSTAT registers. If these bits are
read at 0, the software needs to re-prime the endpoint by writing 1 to the corresponding
bit in the ENDPTPRIME register. This can be done for every microframe, every frame or
with a larger interval, depending on the urgency of transfer execution for the application.
Tested-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Define ci_get_revision API to know the controller revision
information according to chipidea 1.1a, 2.0a and 2.5a spec.
Besides, add one entry at struct ci_hdrc to indicate revision
information, it can be used for adding different code for
revisions, eg kinds of errata.
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Using hw_write_id_reg and hw_read_id_reg to write and read identification
registers contents, they can be used to get controller information, change
some system configurations, and so on.
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Except the same process with earlier imx6, it has below two features:

- Choose which vbus voltage as vbus wakeup source
We choose B_SESSION_VALID as vbus wakeup source since when the system
goes to suspend, the vbus comparator can't compare the vbus voltage
for VBUS_VALID.

- Disable dp/dm (linestate) change as wakeup source at device mode
when the vbus is not there, we don't expect dp/dm change waking up
usb controller at this situation.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add compatible string for imx6sx-usbmisc.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

We need to do it for all otg capable controller, not only peripheral
featured otg capable controller, otherwise, the host-only role, but
otg capable controller may be responded by otg interrupt.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add the example for how to enable USB as system wakeup source.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Enable USB as system wakeup source, and each platform needs to implement
imx_usbmisc_set_wakeup in usbmisc_imx.c to support.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The USB signal can be system wakeup source, this patch add the
support, for how to enable it, see Documentation/usb/chipidea.txt.
Since USB wakeup enable logic is vendor/platform specific, the
glue layer needs to implement it to support this feature.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add runtime pm support for imx, only imx6 series are supported and tested.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This API is used to enable/disable usb wakeup, only imx6 series are
added, since I don't have other imx hardware on hand. Other imx users
can add their API according to reference manual after testing.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add runtime power management support.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Move struct imx_usbmisc_data NULL pointer judgement from caller to
each API, it can simplify the caller.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

All imx usb controller's non core registers uses the same clock gate with
core registers, the usbmisc_imx is the library for imx glue driver, the
glue keeps clock on when it calls usbmisc_imx API to change non-core register.

Besides, we will support runtime pm in the future, it also needs to
close this clock when the usb is not in use.

Philipp Zabel also verifies it at imx6q platform, see
http://www.spinics.net/lists/linux-usb/msg118491.html

Cc: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

It is meaningless the glue layer driver has its own platform flag
which is the same meaning with common platform flag.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Some gadget driver (like uac1) will try to enable endpoint again even
the ep is not empty, it will cause the ep reset again and may affect
the dTD list which has already queued.

It returns -EBUSY immediately, and indicate the endpoint is in use.
In this way, the ep's behavior will not be affected, and the gadget
driver is also notified.

Cc: Xuebing Wang <xbing6@gmail.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

POLL_OUT isn't what callers of ->poll() are expecting to see; it's
actually __SI_POLL | 2 and it's a siginfo code, not a poll bitmap
bit...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: stable@vger.kernel.org
Cc: Bruce Fields <bfields@fieldses.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull USB fixes from Greg KH:
 "Here's a round of USB fixes for 4.0-rc3.

  Nothing major, the usual gadget, xhci and usb-serial fixes and a few
  new device ids as well.

  All have been in linux-next successfully"

* tag 'usb-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (36 commits)
  xhci: Workaround for PME stuck issues in Intel xhci
  xhci: fix reporting of 0-sized URBs in control endpoint
  usb: ftdi_sio: Add jtag quirk support for Cyber Cortex AV boards
  USB: ch341: set tty baud speed according to tty struct
  USB: serial: cp210x: Adding Seletek device id's
  USB: pl2303: disable break on shutdown
  USB: mxuport: fix null deref when used as a console
  USB: serial: clean up bus probe error handling
  USB: serial: fix port attribute-creation race
  USB: serial: fix tty-device error handling at probe
  USB: serial: fix potential use-after-free after failed probe
  USB: console: add dummy __module_get
  USB: ftdi_sio: add PIDs for Actisense USB devices
  Revert "USB: serial: make bulk_out_size a lower limit"
  cdc-acm: Add support for Denso cradle CU-321
  usb-storage: support for more than 8 LUNs
  uas: Add US_FL_NO_REPORT_OPCODES for JMicron JMS539
  USB: usbfs: don't leak kernel data in siginfo
  xhci: Clear the host side toggle manually when endpoint is 'soft reset'
  xhci: Allocate correct amount of scratchpad buffers
  ...

Pull tty/serial fixes from Greg KH:
 "Here are some tty and serial driver fixes for 4.0-rc3.

  Along with the atime fix that you know about, here are some other
  serial driver bugfixes as well.  Most notable is a wait_until_sent
  bugfix that was traced back to being around since before 2.6.12 that
  Johan has fixed up.

  All have been in linux-next successfully"

* tag 'tty-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  TTY: fix tty_wait_until_sent maximum timeout
  TTY: fix tty_wait_until_sent on 64-bit machines
  USB: serial: fix infinite wait_until_sent timeout
  TTY: bfin_jtag_comm: remove incorrect wait_until_sent operation
  net: irda: fix wait_until_sent poll timeout
  serial: uapi: Declare all userspace-visible io types
  serial: core: Fix iotype userspace breakage
  serial: sprd: Fix missing spin_unlock in sprd_handle_irq()
  console: Fix console name size mismatch
  tty: fix up atime/mtime mess, take four
  serial: 8250_dw: Fix get_mctrl behaviour
  serial:8250:8250_pci: delete unneeded quirk entries
  serial:8250:8250_pci: fix redundant entry report for WCH_CH352_2S
  Change email address for 8250_pci
  serial: 8250: Revert "tty: serial: 8250_core: read only RX if there is something in the FIFO"
  Revert "tty/serial: of_serial: add DT alias ID handling"

Pull staging driver fixes from Greg KH:
 "Here are some IIO and staging driver fixes for 4.0-rc3.

  Details are in the shortlog, nothing major, mostly IIO fixes for
  reported issues.

  All have been in linux-next successfully"

* tag 'staging-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (23 commits)
  staging: comedi: adv_pci1710: fix AI INSN_READ for non-zero channel
  staging: comedi: vmk80xx: remove "firmware version" kernel messages
  staging: comedi: comedi_isadma: fix "stalled" detect in comedi_isadma_disable_on_sample()
  iio: ak8975: fix AK09911 dependencies
  iio: common: ssp_sensors: Protect PM-only functions to kill warning
  IIO: si7020: Allocate correct amount of memory in devm_iio_device_alloc
  Revert "iio:humidity:si7020: fix pointer to i2c client"
  iio: light: gp2ap020a00f: Select REGMAP_I2C
  iio: light: jsa1212: Select REGMAP_I2C
  iio: ad5686: fix optional reference voltage declaration
  iio:adc:mcp3422 Fix incorrect scales table
  iio: mxs-lradc: fix iio channel map regression
  iio: imu: adis16400: Fix sign extension
  staging: iio: ad2s1200: Fix sign extension
  iio: mxs-lradc: only update the buffer when its conversions have finished
  iio: mxs-lradc: make ADC reads not unschedule touchscreen conversions
  iio: mxs-lradc: make ADC reads not disable touchscreen interrupts
  iio: mxs-lradc: separate touchscreen and buffer virtual channels
  iio: imu: inv_mpu6050: Prevent dereferencing NULL
  iio: iadc: wait_for_completion_timeout time in jiffies
  ...

Pull char/misc driver fixes from Greg KH:
 "Here are two char/misc fixes for 4.0-rc3.

  One is a reported binder driver fix needed due to a change in the mm
  core that happened in 4.0-rc1.  Another is a mei driver fix that
  resolves a reported issue in that driver.

  Both have been in linux-next for a while"

* tag 'char-misc-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  mei: make device disabled on stop unconditionally
  android: binder: fix binder mmap failures

Pull "code of conflict" from Greg KH:
 "This file tries to set the rational basis for our code reviews, gives
  some advice on how to conduct them, and provides an excalation channel
  for any kernel developers if they so desire it"

[ Let's see how this works ]

* tag 'cc-4.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  Code of Conflict

Pull i2c fixes from Wolfram Sang:
 "A set of updates and bugfixes for the new designware-baytrail driver.

  And a documentation bugfix"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: imx: add required clocks property to binding
  i2c: designware-baytrail: baytrail_i2c_acquire() might sleep
  i2c: designware-baytrail: cross-check lock functions
  i2c: designware-baytrail: fix sparse warnings
  i2c: designware-baytrail: fix typo in error path
  i2c: designware-baytrail: describe magic numbers

Pull slave-dmaengine fixes from Vinod Koul:
 "This contains small fixes spread across the drivers"

* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
  dmaengine: mmp_pdma: fix warning about slave caps
  dmaengine: qcom_bam_dma: fix wrong register offsets
  dmaengine: bam-dma: fix a warning about missing capabilities
  dmaengine: ioatdma: workaround for incorrect DMACAP register
  dmaengine: at_xdmac: fix for chan conf simplification
  dmaengine: dw: don't handle interrupt when dmaengine is not used
  dma: mmp-tdma: refine dma disable and dma-pos update
  dmaengine: shdma: Move DMA stop to (runtime) suspend callbacks
  dmaenegine: mmp-pdma: fix irq handler overwrite physical chan issue

Pull arm64 fixes from Catalin Marinas:
 "arm64 and generic kernel/module.c (acked by Rusty) fixes for
  CONFIG_DEBUG_SET_MODULE_RONX"

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  kernel/module.c: Update debug alignment after symtable generation
  arm64: Don't use is_module_addr in setting page attributes

Currently tty_wait_until_sent may take up to twice as long as the
requested timeout while waiting for driver and hardware buffers to
drain.

Fix this by taking the remaining number of jiffies after waiting for
driver buffers to drain into account so that the timeout actually
becomes a maximum timeout as it is documented to be.

Note that this specifically implies tighter timings when closing a port
as a consequence of actually honouring the port closing-wait setting
for drivers relying on tty_wait_until_sent_from_close (e.g. via
tty_port_close_start).
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix overflow bug in tty_wait_until_sent on 64-bit machines, where an
infinite timeout (0) would be passed to the underlying tty-driver's
wait_until_sent-operation as a negative timeout (-1), causing it to
return immediately.

This manifests itself for example as tcdrain() returning immediately,
drivers not honouring the drain flags when setting terminal attributes,
or even dropped data on close as a requested infinite closing-wait
timeout would be ignored.

The first symptom  was reported by Asier LLANO who noted that tcdrain()
returned prematurely when using the ftdi_sio usb-serial driver.

Fix this by passing 0 rather than MAX_SCHEDULE_TIMEOUT (LONG_MAX) to the
underlying tty driver.

Note that the serial-core wait_until_sent-implementation is not affected
by this bug due to a lucky chance (comparison to an unsigned maximum
timeout), and neither is the cyclades one that had an explicit check for
negative timeouts, but all other tty drivers appear to be affected.

Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>	# v2.6.12
Reported-by: ZIV-Asier Llano Palacios <asier.llano@cgglobal.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Make sure to handle an infinite timeout (0).

Note that wait_until_sent is currently never called with a 0-timeout
argument due to a bug in tty_wait_until_sent.

Fixes: dcf01050 ("USB: serial: add generic wait_until_sent
implementation")
Cc: stable <stable@vger.kernel.org>	# v3.10
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove incorrect and redundant wait_until_sent operation, which waits
for the driver buffer rather than any hardware buffers to drain,
something which is already taken care of by the tty layer (and
chars_in_buffer).
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In case an infinite timeout (0) is requested, the irda wait_until_sent
implementation would use a zero poll timeout rather than the default
200ms.

Note that wait_until_sent is currently never called with a 0-timeout
argument due to a bug in tty_wait_until_sent.

Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>	# v2.6.12
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ioctl(TIOCGSERIAL|TIOCSSERIAL) report and can change the port->iotype.
UART drivers use the UPIO_* definitions, but the uapi header defines
parallel values and userspace uses these parallel values for ioctls;
thus the userspace values are definitive.

Define UPIO_* iotypes in terms of the uapi defines, SERIAL_IO_*;
extend the uapi defines to include all values in use by the serial
core.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 3ffb1a81 ("serial: core: Add big-endian iotype")
re-numbered userspace-dependent values; ioctl(TIOCSSERIAL) can
assign the port iotype (which is expected to match the selected
i/o accessors), so iotype values must not be changed.

Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: <stable@vger.kernel.org> # 3.19+
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Reviewed-by: Kevin Cernekee <cernekee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>