In commit 65c93628 ("bpftool: Add struct_ops support") a new
type of command named struct_ops has been added. This command requires
a kernel with CONFIG_DEBUG_INFO_BTF=y set and for retrieving BTF info
in bpftool, the helper get_btf_vmlinux() is used.

When running this command on kernel without BTF debug info, this will
lead to 'btf_vmlinux' variable being an invalid(error) pointer. And by
this, btf_free() causes a segfault when executing 'bpftool struct_ops'.

This commit adds pointer validation with IS_ERR not to free invalid
pointer, and this will fix the segfault issue.

Fixes: 65c93628 ("bpftool: Add struct_ops support")
Signed-off-by: Daniel T. Lee <danieltimlee@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20200410020612.2930667-1-danieltimlee@gmail.com

Test that frozen and mmap()'ed BPF map can't be mprotect()'ed as writable or
executable memory. Also validate that "downgrading" from writable to read-only
doesn't screw up internal writable count accounting for the purposes of map
freezing.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20200410202613.3679837-2-andriin@fb.com

VM_MAYWRITE flag during initial memory mapping determines if already mmap()'ed
pages can be later remapped as writable ones through mprotect() call. To
prevent user application to rewrite contents of memory-mapped as read-only and
subsequently frozen BPF map, remove VM_MAYWRITE flag completely on initially
read-only mapping.

Alternatively, we could treat any memory-mapping on unfrozen map as writable
and bump writecnt instead. But there is little legitimate reason to map
BPF map as read-only and then re-mmap() it as writable through mprotect(),
instead of just mmap()'ing it as read/write from the very beginning.

Also, at the suggestion of Jann Horn, drop unnecessary refcounting in mmap
operations. We can just rely on VMA holding reference to BPF map's file
properly.

Fixes: fc970227 ("bpf: Add mmap() support for BPF_MAP_TYPE_ARRAY")
Reported-by: Jann Horn <jannh@google.com>
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Jann Horn <jannh@google.com>
Link: https://lore.kernel.org/bpf/20200410202613.3679837-1-andriin@fb.com

This patch fixes an incorrect check in how immediate memory offsets are
computed for BPF_DW on arm.

For BPF_LDX/ST/STX + BPF_DW, the 32-bit arm JIT breaks down an 8-byte
access into two separate 4-byte accesses using off+0 and off+4. If off
fits in imm12, the JIT emits a ldr/str instruction with the immediate
and avoids the use of a temporary register. While the current check off
<= 0xfff ensures that the first immediate off+0 doesn't overflow imm12,
it's not sufficient for the second immediate off+4, which may cause the
second access of BPF_DW to read/write the wrong address.

This patch fixes the problem by changing the check to
off <= 0xfff - 4 for BPF_DW, ensuring off+4 will never overflow.

A side effect of simplifying the check is that it now allows using
negative immediate offsets in ldr/str. This means that small negative
offsets can also avoid the use of a temporary register.

This patch introduces no new failures in test_verifier or test_bpf.c.

Fixes: c5eae692 ("ARM: net: bpf: improve 64-bit store implementation")
Fixes: ec19e02b ("ARM: net: bpf: fix LDX instructions")
Co-developed-by: Xi Wang <xi.wang@gmail.com>
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Signed-off-by: Luke Nelson <luke.r.nels@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20200409221752.28448-1-luke.r.nels@gmail.com

mptcp_connect/28740 is trying to release lock (sk_lock-AF_INET) at:
[<ffffffff82c15869>] mptcp_poll+0xb9/0x550
but there are no more locks to release!
Call Trace:
 lock_release+0x50f/0x750
 release_sock+0x171/0x1b0
 mptcp_poll+0xb9/0x550
 sock_poll+0x157/0x470
 ? get_net_ns+0xb0/0xb0
 do_sys_poll+0x63c/0xdd0

Problem is that __mptcp_tcp_fallback() releases the mptcp socket lock,
but after recent change it doesn't do this in all of its return paths.

To fix this, remove the unlock from __mptcp_tcp_fallback() and
always do the unlock in the caller.

Also add a small comment as to why we have this
__mptcp_needs_tcp_fallback().

Fixes: 0b4f33de ("mptcp: fix tcp fallback crash")
Reported-by: syzbot+e56606435b7bfeea8cf5@syzkaller.appspotmail.com
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

This allows netif_receive_generic_xdp() to correctly determine the RX
queue from which the skb is coming, so that the context passed to the
XDP program will contain the correct RX queue index.
Signed-off-by: Gilberto Bertin <me@jibi.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

Message logged by 'dev_xxx()' or 'pr_xxx()' should end with a '\n'.

Fixes: 93a76530 ("net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Message logged by 'dev_xxx()' or 'pr_xxx()' should end with a '\n'.

Fixes: a646d6ec ("soc: qcom: ipa: modem and microcontroller")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The variable tmp64 is being initialized with a value that is never read
and it is being updated later with a new value.  The initialization is
redundant and can be removed.

Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The negotiation of flow control / pause frame modes was broken since
commit fcf1f59a ("net: phy: marvell: rearrange to use
genphy_read_lpa()") moved the setting of phydev->duplex below the
phy_resolve_aneg_pause call. Due to a check of DUPLEX_FULL in that
function, phydev->pause was no longer set.

Fix it by moving the parsing of the status variable before the blocks
dealing with the pause frames.

As the Marvell 88E1510 datasheet does not specify the timing between the
link status and the "Speed and Duplex Resolved" bit, we have to force
the link down as long as the resolved bit is not set, to avoid reporting
link up before we even have valid Speed/Duplex.

Tested with a Marvell 88E1510 (RGMII to Copper/1000Base-T)

Fixes: fcf1f59a ("net: phy: marvell: rearrange to use genphy_read_lpa()")
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Add the full net DIM API to the net_dim.rst file.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Convert the Dynamic Interrupt Moderation doc to RST and
use the RST features like syntax highlight, function and
structure documentation, enumerations, table of contents.
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Daniel Borkmann says:

====================
pull-request: bpf 2020-04-10

The following pull-request contains BPF updates for your *net* tree.

We've added 13 non-merge commits during the last 7 day(s) which contain
a total of 13 files changed, 137 insertions(+), 43 deletions(-).

The main changes are:

1) JIT code emission fixes for riscv and arm32, from Luke Nelson and Xi Wang.

2) Disable vmlinux BTF info if GCC_PLUGIN_RANDSTRUCT is used, from Slava Bacherikov.

3) Fix oob write in AF_XDP when meta data is used, from Li RongQing.

4) Fix bpf_get_link_xdp_id() handling on single prog when flags are specified,
   from Andrey Ignatov.

5) Fix sk_assign() BPF helper for request sockets that can have sk_reuseport
   field uninitialized, from Joe Stringer.

6) Fix mprotect() test case for the BPF LSM, from KP Singh.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

When CONFIG_IP_MULTICAST is not set and multicast ip is added to the device
with autojoin flag or when multicast ip is deleted kernel will crash.

steps to reproduce:

ip addr add 224.0.0.0/32 dev eth0
ip addr del 224.0.0.0/32 dev eth0

or

ip addr add 224.0.0.0/32 dev eth0 autojoin

Unable to handle kernel NULL pointer dereference at virtual address 0000000000000088
 pc : _raw_write_lock_irqsave+0x1e0/0x2ac
 lr : lock_sock_nested+0x1c/0x60
 Call trace:
  _raw_write_lock_irqsave+0x1e0/0x2ac
  lock_sock_nested+0x1c/0x60
  ip_mc_config.isra.28+0x50/0xe0
  inet_rtm_deladdr+0x1a8/0x1f0
  rtnetlink_rcv_msg+0x120/0x350
  netlink_rcv_skb+0x58/0x120
  rtnetlink_rcv+0x14/0x20
  netlink_unicast+0x1b8/0x270
  netlink_sendmsg+0x1a0/0x3b0
  ____sys_sendmsg+0x248/0x290
  ___sys_sendmsg+0x80/0xc0
  __sys_sendmsg+0x68/0xc0
  __arm64_sys_sendmsg+0x20/0x30
  el0_svc_common.constprop.2+0x88/0x150
  do_el0_svc+0x20/0x80
 el0_sync_handler+0x118/0x190
  el0_sync+0x140/0x180

Fixes: 93a714d6 ("multicast: Extend ip address command to enable multicast group join/leave on")
Signed-off-by: Taras Chornyi <taras.chornyi@plvision.eu>
Signed-off-by: Vadym Kochan <vadym.kochan@plvision.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>

In rds_free_mr(), it calls rds_destroy_mr(mr) directly.  But this
defeats the purpose of reference counting and makes MR free handling
impossible.  It means that holding a reference does not guarantee that
it is safe to access some fields.  For example, In
rds_cmsg_rdma_dest(), it increases the ref count, unlocks and then
calls mr->r_trans->sync_mr().  But if rds_free_mr() (and
rds_destroy_mr()) is called in between (there is no lock preventing
this to happen), r_trans_private is set to NULL, causing a panic.
Similar issue is in rds_rdma_unuse().
Reported-by: zerons <sironhide0null@gmail.com>
Signed-off-by: Ka-Cheong Poon <ka-cheong.poon@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

And removed rds_mr_put().
Signed-off-by: Ka-Cheong Poon <ka-cheong.poon@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the macsec_changelink(), "struct macsec_tx_sa tx_sc" is used to
store "macsec_secy.tx_sc".
But, the struct type of tx_sc is macsec_tx_sc, not macsec_tx_sa.
So, the macsec_tx_sc should be used instead.

Test commands:
    ip link add dummy0 type dummy
    ip link add macsec0 link dummy0 type macsec
    ip link set macsec0 type macsec encrypt off

Splat looks like:
[61119.963483][ T9335] ==================================================================
[61119.964709][ T9335] BUG: KASAN: slab-out-of-bounds in macsec_changelink.part.34+0xb6/0x200 [macsec]
[61119.965787][ T9335] Read of size 160 at addr ffff888020d69c68 by task ip/9335
[61119.966699][ T9335]
[61119.966979][ T9335] CPU: 0 PID: 9335 Comm: ip Not tainted 5.6.0+ #503
[61119.967791][ T9335] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[61119.968914][ T9335] Call Trace:
[61119.969324][ T9335]  dump_stack+0x96/0xdb
[61119.969809][ T9335]  ? macsec_changelink.part.34+0xb6/0x200 [macsec]
[61119.970554][ T9335]  print_address_description.constprop.5+0x1be/0x360
[61119.971294][ T9335]  ? macsec_changelink.part.34+0xb6/0x200 [macsec]
[61119.971973][ T9335]  ? macsec_changelink.part.34+0xb6/0x200 [macsec]
[61119.972703][ T9335]  __kasan_report+0x12a/0x170
[61119.973323][ T9335]  ? macsec_changelink.part.34+0xb6/0x200 [macsec]
[61119.973942][ T9335]  kasan_report+0xe/0x20
[61119.974397][ T9335]  check_memory_region+0x149/0x1a0
[61119.974866][ T9335]  memcpy+0x1f/0x50
[61119.975209][ T9335]  macsec_changelink.part.34+0xb6/0x200 [macsec]
[61119.975825][ T9335]  ? macsec_get_stats64+0x3e0/0x3e0 [macsec]
[61119.976451][ T9335]  ? kernel_text_address+0x111/0x120
[61119.976990][ T9335]  ? pskb_expand_head+0x25f/0xe10
[61119.977503][ T9335]  ? stack_trace_save+0x82/0xb0
[61119.977986][ T9335]  ? memset+0x1f/0x40
[61119.978397][ T9335]  ? __nla_validate_parse+0x98/0x1ab0
[61119.978936][ T9335]  ? macsec_alloc_tfm+0x90/0x90 [macsec]
[61119.979511][ T9335]  ? __kasan_slab_free+0x111/0x150
[61119.980021][ T9335]  ? kfree+0xce/0x2f0
[61119.980700][ T9335]  ? netlink_trim+0x196/0x1f0
[61119.981420][ T9335]  ? nla_memcpy+0x90/0x90
[61119.982036][ T9335]  ? register_lock_class+0x19e0/0x19e0
[61119.982776][ T9335]  ? memcpy+0x34/0x50
[61119.983327][ T9335]  __rtnl_newlink+0x922/0x1270
[ ... ]

Fixes: 3cf3227a ("net: macsec: hardware offloading infrastructure")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The variable ret is being initialized with a value that is never read
and it is being updated later with a new value.  The initialization is
redundant and can be removed.

Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If the local node id(qrtr_local_nid) is not modified after its
initialization, it equals to the broadcast node id(QRTR_NODE_BCAST).
So the messages from local node should not be taken as broadcast
and keep the process going to send them out anyway.

The definitions are as follow:
static unsigned int qrtr_local_nid = NUMA_NO_NODE;

Fixes: fdf5fd39 ("net: qrtr: Broadcast messages only from control port")
Signed-off-by: Wang Wenhu <wenhu.wang@vivo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
Mellanox, mlx5 fixes 2020-04-08

This series introduces some fixes to mlx5 driver.

Please pull and let me know if there is any problem.

For -stable v5.3
 ('net/mlx5: Fix frequent ioread PCI access during recovery')
 ('net/mlx5e: Add missing release firmware call')

For -stable v5.4
 ('net/mlx5e: Fix nest_level for vlan pop action')
 ('net/mlx5e: Fix pfnum in devlink port attribute')
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

At 'make htmldocs' the following warning is thrown:

Documentation/networking/devlink/devlink-trap.rst:302:
WARNING: undefined label: generic-packet-trap-groups

Fixes the warning by setting the label to the specified header,
within the same document.
Signed-off-by: Lothar Rubusch <l.rubusch@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The current arm BPF JIT does not correctly compile RSH or ARSH when the
immediate shift amount is 0. This causes the "rsh64 by 0 imm" and "arsh64
by 0 imm" BPF selftests to hang the kernel by reaching an instruction
the verifier determines to be unreachable.

The root cause is in how immediate right shifts are encoded on arm.
For LSR and ASR (logical and arithmetic right shift), a bit-pattern
of 00000 in the immediate encodes a shift amount of 32. When the BPF
immediate is 0, the generated code shifts by 32 instead of the expected
behavior (a no-op).

This patch fixes the bugs by adding an additional check if the BPF
immediate is 0. After the change, the above mentioned BPF selftests pass.

Fixes: 39c13c20 ("arm: eBPF JIT compiler")
Co-developed-by: Xi Wang <xi.wang@gmail.com>
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Signed-off-by: Luke Nelson <luke.r.nels@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20200408181229.10909-1-luke.r.nels@gmail.com

In testing, we found that for request sockets the sk->sk_reuseport field
may yet be uninitialized, which caused bpf_sk_assign() to randomly
succeed or return -ESOCKTNOSUPPORT when handling the forward ACK in a
three-way handshake.

Fix it by only applying the reuseport check for full sockets.

Fixes: cf7fbe66 ("bpf: Add socket assign support")
Signed-off-by: Joe Stringer <joe@wand.net.nz>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20200408033540.10339-1-joe@wand.net.nz

Fixes CT entries list corruption.

After allowing parallel insertion/removals in upper nf flow table
layer, unprotected ct entries list can be corrupted by parallel add/del
on the same flow table.

CT entries list is only used while freeing a ct zone flow table to
go over all the ct entries offloaded on that zone/table, and flush
the table.

As rhashtable already provides an api to go over all the inserted entries,
fix the race by using the rhashtable iteration instead, and remove the list.

Fixes: 7da182a9 ("netfilter: flowtable: Use work entry per offload command")
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

In cited commit netdevice is registered after devlink port.

Unregistration flow should be mirror sequence of registration flow.
Hence, unregister netdevice before devlink port.

Fixes: 31e87b39 ("net/mlx5e: Fix devlink port register sequence")
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Cited patch missed to extract PCI pf number accurately for PF and VF
port flavour. It considered PCI device + function number.
Due to this, device having non zero device number shown large pfnum.

Hence, use only PCI function number; to avoid similar errors, derive
pfnum one time for all port flavours.

Fixes: f60f315d ("net/mlx5e: Register devlink ports for physical link, PCI PF, VFs")
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

With ct clear action we should not allocate the action in hw
and not release the mod_acts parsed in advance.
It will be done when handling the ct clear action.

Fixes: 1ef3018f ("net/mlx5e: CT: Support clear action")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Current value of nest_level, assigned from net_device lower_level value,
does not reflect the actual number of vlan headers, needed to pop.
For ex., if we have untagged ingress traffic sended over vlan devices,
instead of one pop action, driver will perform two pop actions.
To fix that, calculate nest_level as difference between vlan device and
parent device lower_levels.

Fixes: f3b0a18b ("net: remove unnecessary variables and callback")
Signed-off-by: Dmytro Linkin <dmitrolin@mellanox.com>
Signed-off-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Once driver finishes flashing the firmware image, it should release it.

Fixes: 9c8bca26 ("mlx5: Move firmware flash implementation to devlink")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

When we destroy rules from slow path we need to avoid destroying
termination tables since termination tables are never created in slow
path. By doing so we avoid destroying the termination table created for the
slow path.

Fixes: d8a2034f ("net/mlx5: Don't use termination tables in slow path")
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

High frequency of PCI ioread calls during recovery flow may cause the
following trace on powerpc:

[ 248.670288] EEH: 2100000 reads ignored for recovering device at
location=Slot1 driver=mlx5_core pci addr=0000:01:00.1
[ 248.670331] EEH: Might be infinite loop in mlx5_core driver
[ 248.670361] CPU: 2 PID: 35247 Comm: kworker/u192:11 Kdump: loaded
Tainted: G OE ------------ 4.14.0-115.14.1.el7a.ppc64le #1
[ 248.670425] Workqueue: mlx5_health0000:01:00.1 health_recover_work
[mlx5_core]
[ 248.670471] Call Trace:
[ 248.670492] [c00020391c11b960] [c000000000c217ac] dump_stack+0xb0/0xf4
(unreliable)
[ 248.670548] [c00020391c11b9a0] [c000000000045818]
eeh_check_failure+0x5c8/0x630
[ 248.670631] [c00020391c11ba50] [c00000000068fce4]
ioread32be+0x114/0x1c0
[ 248.670692] [c00020391c11bac0] [c00800000dd8b400]
mlx5_error_sw_reset+0x160/0x510 [mlx5_core]
[ 248.670752] [c00020391c11bb60] [c00800000dd75824]
mlx5_disable_device+0x34/0x1d0 [mlx5_core]
[ 248.670822] [c00020391c11bbe0] [c00800000dd8affc]
health_recover_work+0x11c/0x3c0 [mlx5_core]
[ 248.670891] [c00020391c11bc80] [c000000000164fcc]
process_one_work+0x1bc/0x5f0
[ 248.670955] [c00020391c11bd20] [c000000000167f8c]
worker_thread+0xac/0x6b0
[ 248.671015] [c00020391c11bdc0] [c000000000171618] kthread+0x168/0x1b0
[ 248.671067] [c00020391c11be30] [c00000000000b65c]
ret_from_kernel_thread+0x5c/0x80

Reduce the PCI ioread frequency during recovery by using msleep()
instead of cond_resched()

Fixes: 3e5b72ac ("net/mlx5: Issue SW reset on FW assert")
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Building with some experimental patches, I came across a warning
in the tls code:

include/linux/compiler.h:215:30: warning: assignment discards 'const' qualifier from pointer target type [-Wdiscarded-qualifiers]
  215 |  *(volatile typeof(x) *)&(x) = (val);  \
      |                              ^
net/tls/tls_main.c:650:4: note: in expansion of macro 'smp_store_release'
  650 |    smp_store_release(&saved_tcpv4_prot, prot);

This appears to be a legitimate warning about assigning a const pointer
into the non-const 'saved_tcpv4_prot' global. Annotate both the ipv4 and
ipv6 pointers 'const' to make the code internally consistent.

Fixes: 5bb4c45d ("net/tls: Read sk_prot once when building tls proto ops")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Creation and management of L2TPv3 tunnels and session through netlink
requires CAP_NET_ADMIN. However, a process with CAP_NET_ADMIN in a
non-initial user namespace gets an EPERM due to the use of the
genetlink GENL_ADMIN_PERM flag. Thus, management of L2TP VPNs inside
an unprivileged container won't work.

We replaced the GENL_ADMIN_PERM by the GENL_UNS_ADMIN_PERM flag
similar to other network modules which also had this problem, e.g.,
openvswitch (commit 4a92602a "openvswitch: allow management from
inside user namespaces") and nl80211 (commit 5617c6cd "nl80211:
Allow privileged operations from user namespaces").

I tested this in the container runtime trustm3 (trustm3.github.io)
and was able to create l2tp tunnels and sessions in unpriviliged
(user namespaced) containers using a private network namespace.
For other runtimes such as docker or lxc this should work, too.
Signed-off-by: Michael Weiß <michael.weiss@aisec.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Shannon Nelson says:

====================
ionic: fw upgrade filter fixes

With further testing of the fw-upgrade operations we found a
couple of issues that needed to be cleaned up:
 - the filters other than the base MAC address need to be
   reinstated into the device
 - we don't need to remove the station MAC filter if it
   isn't changing from a previous MAC filter
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The code was working too hard and in some cases was trying to
delete filters that weren't there, generating a potentially
misleading error message.
    IONIC_CMD_RX_FILTER_DEL (32) failed: IONIC_RC_ENOENT (-2)

Fixes: 2a654540 ("ionic: Add Rx filter and rx_mode ndo support")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

The NIC's filters are lost in the midst of the fw-upgrade
so we need to replay them into the FW.  We also remove the
unused ionic_rx_filter_del() function.

Fixes: c672412f ("ionic: remove lifs on fw reset")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

In set_operation_mode() function remove duplicated check for args.list
parameter, which is already done one line before.
Signed-off-by: Roman Mashak <mrv@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the current hsr code, only 0 and 1 protocol versions are valid.
But current hsr code doesn't check the version, which is received by
userspace.

Test commands:
    ip link add dummy0 type dummy
    ip link add dummy1 type dummy
    ip link add hsr0 type hsr slave1 dummy0 slave2 dummy1 version 4

In the test commands, version 4 is invalid.
So, the command should be failed.

After this patch, following error will occur.
"Error: hsr: Only versions 0..1 are supported."

Fixes: ee1c2797 ("net/hsr: Added support for HSR v1")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix wrong parameter description and related warnings at 'make htmldocs'.
Signed-off-by: Lothar Rubusch <l.rubusch@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

After driver sets the missed chain on the tc skb extension it is
consumed (deleted) by tc_classify_ingress and tc jumps to that chain.
If tc now misses on this chain (either no match, or no goto action),
then last executed chain remains 0, and the skb extension is not re-added,
and the next datapath (ovs) will start from 0.

Fix that by setting last executed chain to the chain read from the skb
extension, so if there is a miss, we set it back.

Fixes: af699626 ("net: sched: Support specifying a starting chain via tc skb ext")
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>