commit 64adde31 upstream.

Currently, there is only a 1 ms sleep after asserting PERST.

Reading the datasheets for different endpoints, some require PERST to be
asserted for 10 ms in order for the endpoint to perform a reset, others
require it to be asserted for 50 ms.

Several SoCs using this driver uses PCIe Mini Card, where we don't know
what endpoint will be plugged in.

The PCI Express Card Electromechanical Specification r2.0, section
2.2, "PERST# Signal" specifies:

"On power up, the deassertion of PERST# is delayed 100 ms (TPVPERL) from
the power rails achieving specified operating limits."

Add a sleep of 100 ms before deasserting PERST, in order to ensure that
we are compliant with the spec.

Fixes: 82a82383 ("PCI: qcom: Add Qualcomm PCIe controller driver")
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Cc: stable@vger.kernel.org # 4.5+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 000dd531 upstream.

PME polling does not take into account that a device that is directly
connected to the host bridge may go into D3cold as well. This leads to a
situation where the PME poll thread reads from a config space of a
device that is in D3cold and gets incorrect information because the
config space is not accessible.

Here is an example from Intel Ice Lake system where two PCIe root ports
are in D3cold (I've instrumented the kernel to log the PMCSR register
contents):

  [   62.971442] pcieport 0000:00:07.1: Check PME status, PMCSR=0xffff
  [   62.971504] pcieport 0000:00:07.0: Check PME status, PMCSR=0xffff

Since 0xffff is interpreted so that PME is pending, the root ports will
be runtime resumed. This repeats over and over again essentially
blocking all runtime power management.

Prevent this from happening by checking whether the device is in D3cold
before its PME status is read.

Fixes: 71a83bd7 ("PCI/PM: add runtime PM support to PCIe port")
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Cc: 3.6+ <stable@vger.kernel.org> # v3.6+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 4df591b2 upstream.

Fix a use-after-free in hv_eject_device_work().

Fixes: 05f151a7 ("PCI: hv: Fix a memory leak in hv_eject_device_work()")
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 4aa5aed2 upstream.

This adds Ice Lake NNPI support to the Intel(R) Trace Hub.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20190621161930.60785-5-alexander.shishkin@linux.intel.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit bcef5b72 upstream.

The function srp_parse_in() is used both for parsing source address
specifications and for target address specifications. Target addresses
must have a port number. Having to specify a port number for source
addresses is inconvenient. Make sure that srp_parse_in() supports again
parsing addresses with no port number.

Cc: <stable@vger.kernel.org>
Fixes: c62adb7d ("IB/srp: Fix IPv6 address parsing")
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 113ab72e upstream.

For large values of the number of zones reported and/or large zone
sizes, the sector increment calculated with

blk_queue_zone_sectors(q) * n

in blk_report_zones() loop can overflow the unsigned int type used for
the calculation as both "n" and blk_queue_zone_sectors() value are
unsigned int. E.g. for a device with 256 MB zones (524288 sectors),
overflow happens with 8192 or more zones reported.

Changing the return type of blk_queue_zone_sectors() to sector_t, fixes
this problem and avoids overflow problem for all other callers of this
helper too. The same change is also applied to the bdev_zone_sectors()
helper.

Fixes: e76239a3 ("block: add a report_zones method")
Cc: stable@vger.kernel.org
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit b4c5875d upstream.

To allow the SCSI subsystem scsi_execute_req() function to issue
requests using large buffers that are better allocated with vmalloc()
rather than kmalloc(), modify bio_map_kern() to allow passing a buffer
allocated with vmalloc().

To do so, detect vmalloc-ed buffers using is_vmalloc_addr(). For
vmalloc-ed buffers, flush the buffer using flush_kernel_vmap_range(),
use vmalloc_to_page() instead of virt_to_page() to obtain the pages of
the buffer, and invalidate the buffer addresses with
invalidate_kernel_vmap_range() on completion of read BIOs. This last
point is executed using the function bio_invalidate_vmalloc_pages()
which is defined only if the architecture defines
ARCH_HAS_FLUSH_KERNEL_DCACHE_PAGE, that is, if the architecture
actually needs the invalidation done.

Fixes: 515ce606 ("scsi: sd_zbc: Fix sd_zbc_report_zones() buffer allocation")
Fixes: e76239a3 ("block: add a report_zones method")
Cc: stable@vger.kernel.org
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit e28ad544 upstream.

DisplayID blocks allow embedding of CEA blocks. The payloads are
identical to traditional top level CEA extension blocks, but the header
is slightly different.

This change allows the CEA parser to find a CEA block inside a DisplayID
block. Additionally, it adds support for parsing the embedded CTA
header. No further changes are necessary due to payload parity.

This change fixes audio support for the Valve Index HMD.
Signed-off-by: Andres Rodriguez <andresx7@gmail.com>
Reviewed-by: Dave Airlie <airlied@redhat.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: <stable@vger.kernel.org> # v4.15
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190619180901.17901-1-andresx7@gmail.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 2f217d58 upstream.

Fill in the L3 performance event select register ThreadMask
bitfield, to enable per hardware thread accounting.
Signed-off-by: Kim Phillips <kim.phillips@amd.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: <stable@vger.kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Gary Hook <Gary.Hook@amd.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Janakarajan Natarajan <Janakarajan.Natarajan@amd.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Martin Liska <mliska@suse.cz>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Pu Wen <puwen@hygon.cn>
Cc: Stephane Eranian <eranian@google.com>
Cc: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Link: https://lkml.kernel.org/r/20190628215906.4276-2-kim.phillips@amd.comSigned-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 16f46411 upstream.

The following commit:

  d7cbbe49 ("perf/x86/amd/uncore: Set ThreadMask and SliceMask for L3 Cache perf events")

enables L3 PMC events for all threads and slices by writing 1's in
'ChL3PmcCfg' (L3 PMC PERF_CTL) register fields.

Those bitfields overlap with high order event select bits in the Data
Fabric PMC control register, however.

So when a user requests raw Data Fabric events (-e amd_df/event=0xYYY/),
the two highest order bits get inadvertently set, changing the counter
select to events that don't exist, and for which no counts are read.

This patch changes the logic to write the L3 masks only when dealing
with L3 PMC counters.

AMD Family 16h and below Northbridge (NB) counters were not affected.
Signed-off-by: Kim Phillips <kim.phillips@amd.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: <stable@vger.kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Gary Hook <Gary.Hook@amd.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Janakarajan Natarajan <Janakarajan.Natarajan@amd.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Martin Liska <mliska@suse.cz>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Pu Wen <puwen@hygon.cn>
Cc: Stephane Eranian <eranian@google.com>
Cc: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Fixes: d7cbbe49 ("perf/x86/amd/uncore: Set ThreadMask and SliceMask for L3 Cache perf events")
Link: https://lkml.kernel.org/r/20190628215906.4276-1-kim.phillips@amd.comSigned-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit e4557c1a upstream.

If a user first sample a PEBS event on a fixed counter, then sample a
non-PEBS event on the same fixed counter on Icelake, it will trigger
spurious NMI. For example:

  perf record -e 'cycles:p' -a
  perf record -e 'cycles' -a

The error message for spurious NMI:

  [June 21 15:38] Uhhuh. NMI received for unknown reason 30 on CPU 2.
  [    +0.000000] Do you have a strange power saving mode enabled?
  [    +0.000000] Dazed and confused, but trying to continue

The bug was introduced by the following commit:

  commit 6f55967a ("perf/x86/intel: Fix race in intel_pmu_disable_event()")

The commit moves the intel_pmu_pebs_disable() after intel_pmu_disable_fixed(),
which returns immediately.  The related bit of PEBS_ENABLE MSR will never be
cleared for the fixed counter. Then a non-PEBS event runs on the fixed counter,
but the bit on PEBS_ENABLE is still set, which triggers spurious NMIs.

Check and disable PEBS for fixed counters after intel_pmu_disable_fixed().
Reported-by: Yi, Ammy <ammy.yi@intel.com>
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: <stable@vger.kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Fixes: 6f55967a ("perf/x86/intel: Fix race in intel_pmu_disable_event()")
Link: https://lkml.kernel.org/r/20190625142135.22112-1-kan.liang@linux.intel.comSigned-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit e74bd969 upstream.

When default_get_smp_config() is called with early == 1 and mpf->feature1
is non-zero, mpf is leaked because the return path does not do
early_memunmap().

Fix this and share a common exit routine.

Fixes: 5997efb9 ("x86/boot: Use memremap() to map the MPF and MPC data")
Reported-by: Cfir Cohen <cfir@google.com>
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/alpine.DEB.2.21.1907091942570.28240@chino.kir.corp.google.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 41a531ff upstream.

Since commit ed194d13 ("usb: core: remove local_irq_save() around
 ->complete() handler") the handler rt2x00usb_interrupt_rxdone() is
not running with interrupts disabled anymore. So this completion handler
is not guaranteed to run completely before workqueue processing starts
for the same queue entry.
Be sure to set all other flags in the entry correctly before marking
this entry ready for workqueue processing. This way we cannot miss error
conditions that need to be signalled from the completion handler to the
worker thread.
Note that rt2x00usb_work_rxdone() processes all available entries, not
only such for which queue_work() was called.

This patch is similar to what commit df71c9cf ("rt2x00: fix order
of entry flags modification") did for TX processing.

This fixes a regression on a RT5370 based wifi stick in AP mode, which
suddenly stopped data transmission after some period of heavy load. Also
stopping the hanging hostapd resulted in the error message "ieee80211
phy0: rt2x00queue_flush_queue: Warning - Queue 14 failed to flush".
Other operation modes are probably affected as well, this just was
the used testcase.

Fixes: ed194d13 ("usb: core: remove local_irq_save() around ->complete() handler")
Cc: stable@vger.kernel.org # 4.20+
Signed-off-by: Soeren Moch <smoch@web.de>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit d4548543 upstream.

KASAN report this:

BUG: unable to handle kernel paging request at ffffffffa0097000
PGD 3870067 P4D 3870067 PUD 3871063 PMD 2326e2067 PTE 0
Oops: 0000 [#1
CPU: 0 PID: 5340 Comm: modprobe Not tainted 5.1.0-rc7+ #25
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.9.3-0-ge2fc41e-prebuilt.qemu-project.org 04/01/2014
RIP: 0010:__list_add_valid+0x10/0x70
Code: c3 48 8b 06 55 48 89 e5 5d 48 39 07 0f 94 c0 0f b6 c0 c3 90 90 90 90 90 90 90 55 48 89 d0 48 8b 52 08 48 89 e5 48 39 f2 75 19 <48> 8b 32 48 39 f0 75 3a

RSP: 0018:ffffc90000e23c68 EFLAGS: 00010246
RAX: ffffffffa00ad000 RBX: ffffffffa009d000 RCX: 0000000000000000
RDX: ffffffffa0097000 RSI: ffffffffa0097000 RDI: ffffffffa009d000
RBP: ffffc90000e23c68 R08: 0000000000000001 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000000 R12: ffffffffa0097000
R13: ffff888231797180 R14: 0000000000000000 R15: ffffc90000e23e78
FS:  00007fb215285540(0000) GS:ffff888237a00000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: ffffffffa0097000 CR3: 000000022f144000 CR4: 00000000000006f0
Call Trace:
 v9fs_register_trans+0x2f/0x60 [9pnet
 ? 0xffffffffa0087000
 p9_virtio_init+0x25/0x1000 [9pnet_virtio
 do_one_initcall+0x6c/0x3cc
 ? kmem_cache_alloc_trace+0x248/0x3b0
 do_init_module+0x5b/0x1f1
 load_module+0x1db1/0x2690
 ? m_show+0x1d0/0x1d0
 __do_sys_finit_module+0xc5/0xd0
 __x64_sys_finit_module+0x15/0x20
 do_syscall_64+0x6b/0x1d0
 entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x7fb214d8e839
Code: 00 f3 c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 40 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01

RSP: 002b:00007ffc96554278 EFLAGS: 00000246 ORIG_RAX: 0000000000000139
RAX: ffffffffffffffda RBX: 000055e67eed2aa0 RCX: 00007fb214d8e839
RDX: 0000000000000000 RSI: 000055e67ce95c2e RDI: 0000000000000003
RBP: 000055e67ce95c2e R08: 0000000000000000 R09: 000055e67eed2aa0
R10: 0000000000000003 R11: 0000000000000246 R12: 0000000000000000
R13: 000055e67eeda500 R14: 0000000000040000 R15: 000055e67eed2aa0
Modules linked in: 9pnet_virtio(+) 9pnet gre rfkill vmw_vsock_virtio_transport_common vsock [last unloaded: 9pnet_virtio
CR2: ffffffffa0097000
---[ end trace 4a52bb13ff07b761

If register_virtio_driver() fails in p9_virtio_init,
we should call v9fs_unregister_trans() to do cleanup.

Link: http://lkml.kernel.org/r/20190430115942.41840-1-yuehaibing@huawei.com
Cc: stable@vger.kernel.org
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: b530cc79 ("9p: add virtio transport")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Dominique Martinet <dominique.martinet@cea.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 80a316ff upstream.

If xenbus_register_frontend() fails in p9_trans_xen_init,
we should call v9fs_unregister_trans() to do cleanup.

Link: http://lkml.kernel.org/r/20190430143933.19368-1-yuehaibing@huawei.com
Cc: stable@vger.kernel.org
Fixes: 868eb122 ("xen/9pfs: introduce Xen 9pfs transport driver")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Dominique Martinet <dominique.martinet@cea.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit bce5963b upstream.

When binding an interdomain event channel to a vcpu via
IOCTL_EVTCHN_BIND_INTERDOMAIN not only the event channel needs to be
bound, but the affinity of the associated IRQi must be changed, too.
Otherwise the IRQ and the event channel won't be moved to another vcpu
in case the original vcpu they were bound to is going offline.

Cc: <stable@vger.kernel.org> # 4.13
Fixes: c48f64ab ("xen-evtchn: Bind dyn evtchn:qemu-dm interrupt to next online VCPU")
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 3b8cafdd upstream.

dm-zoned uses the zone flag DMZ_ACTIVE to indicate that a zone of the
backend device is being actively read or written and so cannot be
reclaimed. This flag is set as long as the zone atomic reference
counter is not 0. When this atomic is decremented and reaches 0 (e.g.
on BIO completion), the active flag is cleared and set again whenever
the zone is reused and BIO issued with the atomic counter incremented.
These 2 operations (atomic inc/dec and flag set/clear) are however not
always executed atomically under the target metadata mutex lock and
this causes the warning:

WARN_ON(!test_bit(DMZ_ACTIVE, &zone->flags));

in dmz_deactivate_zone() to be displayed. This problem is regularly
triggered with xfstests generic/209, generic/300, generic/451 and
xfs/077 with XFS being used as the file system on the dm-zoned target
device. Similarly, xfstests ext4/303, ext4/304, generic/209 and
generic/300 trigger the warning with ext4 use.

This problem can be easily fixed by simply removing the DMZ_ACTIVE flag
and managing the "ACTIVE" state by directly looking at the reference
counter value. To do so, the functions dmz_activate_zone() and
dmz_deactivate_zone() are changed to inline functions respectively
calling atomic_inc() and atomic_dec(), while the dmz_is_active() macro
is changed to an inline function calling atomic_read().

Fixes: 3b1a94c8 ("dm zoned: drive-managed zoned block device target")
Cc: stable@vger.kernel.org
Reported-by: Masato Suzuki <masato.suzuki@wdc.com>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit cf144f81 upstream.

Testing padata with the tcrypt module on a 5.2 kernel...

    # modprobe tcrypt alg="pcrypt(rfc4106(gcm(aes)))" type=3
    # modprobe tcrypt mode=211 sec=1

...produces this splat:

    INFO: task modprobe:10075 blocked for more than 120 seconds.
          Not tainted 5.2.0-base+ #16
    modprobe        D    0 10075  10064 0x80004080
    Call Trace:
     ? __schedule+0x4dd/0x610
     ? ring_buffer_unlock_commit+0x23/0x100
     schedule+0x6c/0x90
     schedule_timeout+0x3b/0x320
     ? trace_buffer_unlock_commit_regs+0x4f/0x1f0
     wait_for_common+0x160/0x1a0
     ? wake_up_q+0x80/0x80
     { crypto_wait_req }             # entries in braces added by hand
     { do_one_aead_op }
     { test_aead_jiffies }
     test_aead_speed.constprop.17+0x681/0xf30 [tcrypt]
     do_test+0x4053/0x6a2b [tcrypt]
     ? 0xffffffffa00f4000
     tcrypt_mod_init+0x50/0x1000 [tcrypt]
     ...

The second modprobe command never finishes because in padata_reorder,
CPU0's load of reorder_objects is executed before the unlocking store in
spin_unlock_bh(pd->lock), causing CPU0 to miss CPU1's increment:

CPU0                                 CPU1

padata_reorder                       padata_do_serial
  LOAD reorder_objects  // 0
                                       INC reorder_objects  // 1
                                       padata_reorder
                                         TRYLOCK pd->lock   // failed
  UNLOCK pd->lock

CPU0 deletes the timer before returning from padata_reorder and since no
other job is submitted to padata, modprobe waits indefinitely.

Add a pair of full barriers to guarantee proper ordering:

CPU0                                 CPU1

padata_reorder                       padata_do_serial
  UNLOCK pd->lock
  smp_mb()
  LOAD reorder_objects
                                       INC reorder_objects
                                       smp_mb__after_atomic()
                                       padata_reorder
                                         TRYLOCK pd->lock

smp_mb__after_atomic is needed so the read part of the trylock operation
comes after the INC, as Andrea points out.   Thanks also to Andrea for
help with writing a litmus test.

Fixes: 16295bec ("padata: Generic parallelization/serialization interface")
Signed-off-by: Daniel Jordan <daniel.m.jordan@oracle.com>
Cc: <stable@vger.kernel.org>
Cc: Andrea Parri <andrea.parri@amarulasolutions.com>
Cc: Boqun Feng <boqun.feng@gmail.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Paul E. McKenney <paulmck@linux.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: linux-arch@vger.kernel.org
Cc: linux-crypto@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 7cb95eee upstream.

It turns out that while disabling i2c bus access from software when the
GPU is suspended was a step in the right direction with:

commit 342406e4 ("drm/nouveau/i2c: Disable i2c bus access after
->fini()")

We also ended up accidentally breaking the vbios init scripts on some
older Tesla GPUs, as apparently said scripts can actually use the i2c
bus. Since these scripts are executed before initializing any
subdevices, we end up failing to acquire access to the i2c bus which has
left a number of cards with their fan controllers uninitialized. Luckily
this doesn't break hardware - it just means the fan gets stuck at 100%.

This also means that we've always been using our i2c busses before
initializing them during the init scripts for older GPUs, we just didn't
notice it until we started preventing them from being used until init.
It's pretty impressive this never caused us any issues before!

So, fix this by initializing our i2c pad and busses during subdev
pre-init. We skip initializing aux busses during pre-init, as those are
guaranteed to only ever be used by nouveau for DP aux transactions.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Tested-by: Marc Meledandri <m.meledandri@gmail.com>
Fixes: 342406e4 ("drm/nouveau/i2c: Disable i2c bus access after ->fini()")
Cc: stable@vger.kernel.org
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit f90b8fda upstream.

The SPI to the display on the DIR-685 is active low, we were
just saved by the SPI library enforcing active low on everything
before, so set it as active low to avoid ambiguity.

Link: https://lore.kernel.org/r/20190715202101.16060-1-linus.walleij@linaro.org
Cc: stable@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 8e2442a5 upstream.

Since commit 00c864f8 ("kconfig: allow all config targets to write
auto.conf if missing"), Kconfig creates include/config/auto.conf in the
defconfig stage when it is missing.

Joonas Kylmälä reported incorrect auto.conf generation under some
circumstances.

To reproduce it, apply the following diff:

|  --- a/arch/arm/configs/imx_v6_v7_defconfig
|  +++ b/arch/arm/configs/imx_v6_v7_defconfig
|  @@ -345,14 +345,7 @@ CONFIG_USB_CONFIGFS_F_MIDI=y
|   CONFIG_USB_CONFIGFS_F_HID=y
|   CONFIG_USB_CONFIGFS_F_UVC=y
|   CONFIG_USB_CONFIGFS_F_PRINTER=y
|  -CONFIG_USB_ZERO=m
|  -CONFIG_USB_AUDIO=m
|  -CONFIG_USB_ETH=m
|  -CONFIG_USB_G_NCM=m
|  -CONFIG_USB_GADGETFS=m
|  -CONFIG_USB_FUNCTIONFS=m
|  -CONFIG_USB_MASS_STORAGE=m
|  -CONFIG_USB_G_SERIAL=m
|  +CONFIG_USB_FUNCTIONFS=y
|   CONFIG_MMC=y
|   CONFIG_MMC_SDHCI=y
|   CONFIG_MMC_SDHCI_PLTFM=y

And then, run:

$ make ARCH=arm mrproper imx_v6_v7_defconfig

You will see CONFIG_USB_FUNCTIONFS=y is correctly contained in the
.config, but not in the auto.conf.

Please note drivers/usb/gadget/legacy/Kconfig is included from a choice
block in drivers/usb/gadget/Kconfig. So USB_FUNCTIONFS is a choice value.

This is probably a similar situation described in commit beaaddb6
("kconfig: tests: test defconfig when two choices interact").

When sym_calc_choice() is called, the choice symbol forgets the
SYMBOL_DEF_USER unless all of its choice values are explicitly set by
the user.

The choice symbol is given just one chance to recall it because
set_all_choice_values() is called if SYMBOL_NEED_SET_CHOICE_VALUES
is set.

When sym_calc_choice() is called again, the choice symbol forgets it
forever, since SYMBOL_NEED_SET_CHOICE_VALUES is a one-time aid.
Hence, we cannot call sym_clear_all_valid() again and again.

It is crazy to repeat set and unset of internal flags. However, we
cannot simply get rid of "sym->flags &= flags | ~SYMBOL_DEF_USER;"
Doing so would re-introduce the problem solved by commit 5d09598d
("kconfig: fix new choices being skipped upon config update").

To work around the issue, conf_write_autoconf() stopped calling
sym_clear_all_valid().

conf_write() must be changed accordingly. Currently, it clears
SYMBOL_WRITE after the symbol is written into the .config file. This
is needed to prevent it from writing the same symbol multiple times in
case the symbol is declared in two or more locations. I added the new
flag SYMBOL_WRITTEN, to track the symbols that have been written.

Anyway, this is a cheesy workaround in order to suppress the issue
as far as defconfig is concerned.

Handling of choices is totally broken. sym_clear_all_valid() is called
every time a user touches a symbol from the GUI interface. To reproduce
it, just add a new symbol drivers/usb/gadget/legacy/Kconfig, then touch
around unrelated symbols from menuconfig. USB_FUNCTIONFS will disappear
from the .config file.

I added the Fixes tag since it is more fatal than before. But, this
has been broken since long long time before, and still it is.
We should take a closer look to fix this correctly somehow.

Fixes: 00c864f8 ("kconfig: allow all config targets to write auto.conf if missing")
Cc: linux-stable <stable@vger.kernel.org> # 4.19+
Reported-by: Joonas Kylmälä <joonas.kylmala@iki.fi>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Joonas Kylmälä <joonas.kylmala@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit ecc8fb54 upstream.

Currently the I3C framework limits SCL frequency to FM speed when
dealing with a mixed slow bus, even if all I2C devices are FM+ capable.

The core was also not accounting for I3C speed limitations when
operating in mixed slow mode and was erroneously using FM+ speed as the
max I2C speed when operating in mixed fast mode.

Fixes: 3a379bbc ("i3c: Add core I3C infrastructure")
Signed-off-by: Vitor Soares <vitor.soares@synopsys.com>
Cc: Boris Brezillon <bbrezillon@kernel.org>
Cc: <stable@vger.kernel.org>
Cc: <linux-kernel@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 5ec27ec7 upstream.

Normally, the inode's i_uid/i_gid are translated relative to s_user_ns,
but this is not a correct behavior for proc.  Since sysctl permission
check in test_perm is done against GLOBAL_ROOT_[UG]ID, it makes more
sense to use these values in u_[ug]id of proc inodes.  In other words:
although uid/gid in the inode is not read during test_perm, the inode
logically belongs to the root of the namespace.  I have confirmed this
with Eric Biederman at LPC and in this thread:
  https://lore.kernel.org/lkml/87k1kzjdff.fsf@xmission.com

Consequences
============

Since the i_[ug]id values of proc nodes are not used for permissions
checks, this change usually makes no functional difference.  However, it
causes an issue in a setup where:

 * a namespace container is created without root user in container -
   hence the i_[ug]id of proc nodes are set to INVALID_[UG]ID

 * container creator tries to configure it by writing /proc/sys files,
   e.g. writing /proc/sys/kernel/shmmax to configure shared memory limit

Kernel does not allow to open an inode for writing if its i_[ug]id are
invalid, making it impossible to write shmmax and thus - configure the
container.

Using a container with no root mapping is apparently rare, but we do use
this configuration at Google.  Also, we use a generic tool to configure
the container limits, and the inability to write any of them causes a
failure.

History
=======

The invalid uids/gids in inodes first appeared due to 81754357 (fs:
Update i_[ug]id_(read|write) to translate relative to s_user_ns).
However, AFAIK, this did not immediately cause any issues.  The
inability to write to these "invalid" inodes was only caused by a later
commit 0bd23d09 (vfs: Don't modify inodes with a uid or gid unknown
to the vfs).

Tested: Used a repro program that creates a user namespace without any
mapping and stat'ed /proc/$PID/root/proc/sys/kernel/shmmax from outside.
Before the change, it shows the overflow uid, with the change it's 0.
The overflow uid indicates that the uid in the inode is not correct and
thus it is not possible to open the file for writing.

Link: http://lkml.kernel.org/r/20190708115130.250149-1-rburny@google.com
Fixes: 0bd23d09 ("vfs: Don't modify inodes with a uid or gid unknown to the vfs")
Signed-off-by: Radoslaw Burny <rburny@google.com>
Acked-by: Luis Chamberlain <mcgrof@kernel.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: "Eric W . Biederman" <ebiederm@xmission.com>
Cc: Seth Forshee <seth.forshee@canonical.com>
Cc: John Sperbeck <jsperbeck@google.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: <stable@vger.kernel.org>	[4.8+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 7a0cf094 upstream.

The function send_signal was split from __send_signal so that it would
be possible to bypass the namespace logic based upon current[1].  As it
turns out the si_pid and the si_uid fixup are both inappropriate in
the case of kill_pid_usb_asyncio so move that logic into send_signal.

It is difficult to arrange but possible for a signal with an si_code
of SI_TIMER or SI_SIGIO to be sent across namespace boundaries.  In
which case tests for when it is ok to change si_pid and si_uid based
on SI_FROMUSER are incorrect.  Replace the use of SI_FROMUSER with a
new test has_si_pid_and_used based on siginfo_layout.

Now that the uid fixup is no longer present after expanding
SEND_SIG_NOINFO properly calculate the si_uid that the target
task needs to read.

[1] 7978b567 ("signals: add from_ancestor_ns parameter to send_signal()")
Cc: stable@vger.kernel.org
Fixes: 6588c1e3 ("signals: SI_USER: Masquerade si_pid when crossing pid ns boundary")
Fixes: 6b550f94 ("user namespace: make signal.c respect user namespaces")
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 70f1b0d3 upstream.

The usb support for asyncio encoded one of it's values in the wrong
field.  It should have used si_value but instead used si_addr which is
not present in the _rt union member of struct siginfo.

The practical result of this is that on a 64bit big endian kernel
when delivering a signal to a 32bit process the si_addr field
is set to NULL, instead of the expected pointer value.

This issue can not be fixed in copy_siginfo_to_user32 as the usb
usage of the the _sigfault (aka si_addr) member of the siginfo
union when SI_ASYNCIO is set is incompatible with the POSIX and
glibc usage of the _rt member of the siginfo union.

Therefore replace kill_pid_info_as_cred with kill_pid_usb_asyncio a
dedicated function for this one specific case.  There are no other
users of kill_pid_info_as_cred so this specialization should have no
impact on the amount of code in the kernel.  Have kill_pid_usb_asyncio
take instead of a siginfo_t which is difficult and error prone, 3
arguments, a signal number, an errno value, and an address enconded as
a sigval_t.  The encoding of the address as a sigval_t allows the
code that reads the userspace request for a signal to handle this
compat issue along with all of the other compat issues.

Add BUILD_BUG_ONs in kernel/signal.c to ensure that we can now place
the pointer value at the in si_pid (instead of si_addr).  That is the
code now verifies that si_pid and si_addr always occur at the same
location.  Further the code veries that for native structures a value
placed in si_pid and spilling into si_uid will appear in userspace in
si_addr (on a byte by byte copy of siginfo or a field by field copy of
siginfo).  The code also verifies that for a 64bit kernel and a 32bit
userspace the 32bit pointer will fit in si_pid.

I have used the usbsig.c program below written by Alan Stern and
slightly tweaked by me to run on a big endian machine to verify the
issue exists (on sparc64) and to confirm the patch below fixes the issue.

 /* usbsig.c -- test USB async signal delivery */

 #define _GNU_SOURCE
 #include <stdio.h>
 #include <fcntl.h>
 #include <signal.h>
 #include <string.h>
 #include <sys/ioctl.h>
 #include <unistd.h>
 #include <endian.h>
 #include <linux/usb/ch9.h>
 #include <linux/usbdevice_fs.h>

 static struct usbdevfs_urb urb;
 static struct usbdevfs_disconnectsignal ds;
 static volatile sig_atomic_t done = 0;

 void urb_handler(int sig, siginfo_t *info , void *ucontext)
 {
 	printf("Got signal %d, signo %d errno %d code %d addr: %p urb: %p\n",
 	       sig, info->si_signo, info->si_errno, info->si_code,
 	       info->si_addr, &urb);

 	printf("%s\n", (info->si_addr == &urb) ? "Good" : "Bad");
 }

 void ds_handler(int sig, siginfo_t *info , void *ucontext)
 {
 	printf("Got signal %d, signo %d errno %d code %d addr: %p ds: %p\n",
 	       sig, info->si_signo, info->si_errno, info->si_code,
 	       info->si_addr, &ds);

 	printf("%s\n", (info->si_addr == &ds) ? "Good" : "Bad");
 	done = 1;
 }

 int main(int argc, char **argv)
 {
 	char *devfilename;
 	int fd;
 	int rc;
 	struct sigaction act;
 	struct usb_ctrlrequest *req;
 	void *ptr;
 	char buf[80];

 	if (argc != 2) {
 		fprintf(stderr, "Usage: usbsig device-file-name\n");
 		return 1;
 	}

 	devfilename = argv[1];
 	fd = open(devfilename, O_RDWR);
 	if (fd == -1) {
 		perror("Error opening device file");
 		return 1;
 	}

 	act.sa_sigaction = urb_handler;
 	sigemptyset(&act.sa_mask);
 	act.sa_flags = SA_SIGINFO;

 	rc = sigaction(SIGUSR1, &act, NULL);
 	if (rc == -1) {
 		perror("Error in sigaction");
 		return 1;
 	}

 	act.sa_sigaction = ds_handler;
 	sigemptyset(&act.sa_mask);
 	act.sa_flags = SA_SIGINFO;

 	rc = sigaction(SIGUSR2, &act, NULL);
 	if (rc == -1) {
 		perror("Error in sigaction");
 		return 1;
 	}

 	memset(&urb, 0, sizeof(urb));
 	urb.type = USBDEVFS_URB_TYPE_CONTROL;
 	urb.endpoint = USB_DIR_IN | 0;
 	urb.buffer = buf;
 	urb.buffer_length = sizeof(buf);
 	urb.signr = SIGUSR1;

 	req = (struct usb_ctrlrequest *) buf;
 	req->bRequestType = USB_DIR_IN | USB_TYPE_STANDARD | USB_RECIP_DEVICE;
 	req->bRequest = USB_REQ_GET_DESCRIPTOR;
 	req->wValue = htole16(USB_DT_DEVICE << 8);
 	req->wIndex = htole16(0);
 	req->wLength = htole16(sizeof(buf) - sizeof(*req));

 	rc = ioctl(fd, USBDEVFS_SUBMITURB, &urb);
 	if (rc == -1) {
 		perror("Error in SUBMITURB ioctl");
 		return 1;
 	}

 	rc = ioctl(fd, USBDEVFS_REAPURB, &ptr);
 	if (rc == -1) {
 		perror("Error in REAPURB ioctl");
 		return 1;
 	}

 	memset(&ds, 0, sizeof(ds));
 	ds.signr = SIGUSR2;
 	ds.context = &ds;
 	rc = ioctl(fd, USBDEVFS_DISCSIGNAL, &ds);
 	if (rc == -1) {
 		perror("Error in DISCSIGNAL ioctl");
 		return 1;
 	}

 	printf("Waiting for usb disconnect\n");
 	while (!done) {
 		sleep(1);
 	}

 	close(fd);
 	return 0;
 }

Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Oliver Neukum <oneukum@suse.com>
Fixes: v2.3.39
Cc: stable@vger.kernel.org
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit f5706578 upstream.

Some of the inline assembly instruction use the condition flags and need
to include "cc" in the clobber list.

Fixes: 4a503217 ("arm64: irqflags: Use ICC_PMR_EL1 for interrupt masking")
Cc: <stable@vger.kernel.org> # 5.1.x-
Suggested-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit ba24eee6 upstream.

The Tegra AGIC interrupt controller is an ARM GIC400 interrupt
controller. Per the ARM GIC device-tree binding, the first address
region is for the GIC distributor registers and the second address
region is for the GIC CPU interface registers. The address space for
the distributor registers is 4kB, but currently this is incorrectly
defined as 8kB for the Tegra AGIC and overlaps with the CPU interface
registers. Correct the address space for the distributor to be 4kB.

Cc: stable@vger.kernel.org
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Fixes: bcdbde43 ("arm64: tegra: Add AGIC node for Tegra210")
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 6fc3977c upstream.

If a perf_event creation fails due to any reason of the host perf
subsystem, it has no chance to log the corresponding event for guest
which may cause abnormal sampling data in guest result. In debug mode,
this message helps to understand the state of vPMC and we may not
limit the number of occurrences but not in a spamming style.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Like Xu <like.xu@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 3fefd1cd upstream.

When emulating tsr, treclaim and trechkpt, we incorrectly set CR0. The
code currently sets:
    CR0 <- 00 || MSR[TS]
but according to the ISA it should be:
    CR0 <-  0 || MSR[TS] || 0

This fixes the bit shift to put the bits in the correct location.

This is a data integrity issue as CR0 is corrupted.

Fixes: 4bb3c7a0 ("KVM: PPC: Book3S HV: Work around transactional memory bugs in POWER9")
Cc: stable@vger.kernel.org # v4.17+
Tested-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 3c25ab35 upstream.

If we enter an L1 guest with a pending decrementer exception then this
is cleared on guest exit if the guest has writtien a positive value
into the decrementer (indicating that it handled the decrementer
exception) since there is no other way to detect that the guest has
handled the pending exception and that it should be dequeued. In the
event that the L1 guest tries to run a nested (L2) guest immediately
after this and the L2 guest decrementer is negative (which is loaded
by L1 before making the H_ENTER_NESTED hcall), then the pending
decrementer exception isn't cleared and the L2 entry is blocked since
L1 has a pending exception, even though L1 may have already handled
the exception and written a positive value for it's decrementer. This
results in a loop of L1 trying to enter the L2 guest and L0 blocking
the entry since L1 has an interrupt pending with the outcome being
that L2 never gets to run and hangs.

Fix this by clearing any pending decrementer exceptions when L1 makes
the H_ENTER_NESTED hcall since it won't do this if it's decrementer
has gone negative, and anyway it's decrementer has been communicated
to L0 in the hdec_expires field and L0 will return control to L1 when
this goes negative by delivering an H_DECREMENTER exception.

Fixes: 95a6432c ("KVM: PPC: Book3S HV: Streamlined guest entry/exit path on P9 for radix guests")
Cc: stable@vger.kernel.org # v4.20+
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 86953770 upstream.

On POWER9 the decrementer can operate in large decrementer mode where
the decrementer is 56 bits and signed extended to 64 bits. When not
operating in this mode the decrementer behaves as a 32 bit decrementer
which is NOT signed extended (as on POWER8).

Currently when reading a guest decrementer value we don't take into
account whether the large decrementer is enabled or not, and this
means the value will be incorrect when the guest is not using the
large decrementer. Fix this by sign extending the value read when the
guest isn't using the large decrementer.

Fixes: 95a6432c ("KVM: PPC: Book3S HV: Streamlined guest entry/exit path on P9 for radix guests")
Cc: stable@vger.kernel.org # v4.20+
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 4d763b16 upstream.

Raise #GP when guest read/write IA32_XSS, but the CPUID bits
say that it shouldn't exist.

Fixes: 20300099 (kvm: vmx: add MSR logic for XSAVES)
Reported-by: Xiaoyao Li <xiaoyao.li@linux.intel.com>
Reported-by: Tao Xu <tao3.xu@intel.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Wanpeng Li <wanpengli@tencent.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit beb8d93b upstream.

A previous fix to prevent KVM from consuming stale VMCS state after a
failed VM-Entry inadvertantly blocked KVM's handling of machine checks
that occur during VM-Entry.

Per Intel's SDM, a #MC during VM-Entry is handled in one of three ways,
depending on when the #MC is recognoized.  As it pertains to this bug
fix, the third case explicitly states EXIT_REASON_MCE_DURING_VMENTRY
is handled like any other VM-Exit during VM-Entry, i.e. sets bit 31 to
indicate the VM-Entry failed.

If a machine-check event occurs during a VM entry, one of the following occurs:
 - The machine-check event is handled as if it occurred before the VM entry:
        ...
 - The machine-check event is handled after VM entry completes:
        ...
 - A VM-entry failure occurs as described in Section 26.7. The basic
   exit reason is 41, for "VM-entry failure due to machine-check event".

Explicitly handle EXIT_REASON_MCE_DURING_VMENTRY as a one-off case in
vmx_vcpu_run() instead of binning it into vmx_complete_atomic_exit().
Doing so allows vmx_vcpu_run() to handle VMX_EXIT_REASONS_FAILED_VMENTRY
in a sane fashion and also simplifies vmx_complete_atomic_exit() since
VMCS.VM_EXIT_INTR_INFO is guaranteed to be fresh.

Fixes: b060ca3b ("kvm: vmx: Handle VMLAUNCH/VMRESUME failure properly")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 3b013a29 upstream.

If L1 does not set VM_ENTRY_LOAD_BNDCFGS, then L1's BNDCFGS value must
be propagated to vmcs02 since KVM always runs with VM_ENTRY_LOAD_BNDCFGS
when MPX is supported.  Because the value effectively comes from vmcs01,
vmcs02 must be updated even if vmcs12 is clean.

Fixes: 62cf9bd8 ("KVM: nVMX: Fix emulation of VM_ENTRY_LOAD_BNDCFGS")
Cc: stable@vger.kernel.org
Cc: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 73cb8556 upstream.

... as a malicious userspace can run a toy guest to generate invalid
virtual-APIC page addresses in L1, i.e. flood the kernel log with error
messages.

Fixes: 69090810 ("KVM: nVMX: allow tests to use bad virtual-APIC page address")
Cc: stable@vger.kernel.org
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 14f28f5c upstream.

buf->size is an unsigned long; casting that to int will lead to an
overflow if buf->size exceeds INT_MAX.

Fix this by changing the type to unsigned long instead. This is possible
as the buf->size is always aligned to PAGE_SIZE, and therefore the size
will never have values lesser than 0.

Note on backporting to stable: the file used to be under
drivers/media/v4l2-core, it was moved to the current location after 4.14.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit defcdc5d upstream.

PAGE_ALIGN() may wrap the buffer size around to 0. Prevent this by
checking that the aligned value is not smaller than the unaligned one.

Note on backporting to stable: the file used to be under
drivers/media/v4l2-core, it was moved to the current location after 4.14.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 766b9b16 upstream.

The mutex unlock in the threaded interrupt handler is not paired
with any mutex lock. Remove it.

This bug has been here for a really long time, so it applies
to any stable repo.
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 07d89227 upstream.

cfg->type can be overridden by v4l2_ctrl_fill() and the new value is
stored in the local type var. Fix the tests to use this local var.

Fixes: 0996517c ("V4L/DVB: v4l2: Add new control handling framework")
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
[hverkuil-cisco@xs4all.nl: change to !qmenu and !qmenu_int (checkpatch)]
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit d31d07b9 upstream.

Commit e450f4d1 ("ceph: pass inclusive lend parameter to
filemap_write_and_wait_range()") fixed the end offset parameter used to
call filemap_write_and_wait_range and invalidate_inode_pages2_range.
Unfortunately it missed truncate_inode_pages_range, introducing a
regression that is easily detected by xfstest generic/130.

The problem is that when doing direct IO it is possible that an extra page
is truncated from the page cache when the end offset is page aligned.
This can cause data loss if that page hasn't been sync'ed to the OSDs.

While there, change code to use PAGE_ALIGN macro instead.

Cc: stable@vger.kernel.org
Fixes: e450f4d1 ("ceph: pass inclusive lend parameter to filemap_write_and_wait_range()")
Signed-off-by: Luis Henriques <lhenriques@suse.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>