In UDP recvmsg(), we miss an increase of UDP_MIB_INERRORS if the copy
of skb to userspace failed for whatever reason.
Reported-by: Shawn Bohrer <sbohrer@rgmadvisors.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If mlx4_cmd_init() failed, the init_one function returned
success, although no resources were opened.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The order of operations was wrong on the teardown flow.
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>

The search for promisc entries was always done on the first port,
While the addition is done on the correct port.
This lead to resource leackage of promisc entries on the second
port and brought to a state where we could no longer enter to
promiscuous mode after enough iterations of "ifconfig promisc"
on the second port.
Fix that by using the correct port when searching.
Reported-by: Marcelo Ricardo Leitner <mleitner@redhat.com>
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since VFs may be mapped to VMs which aren't trusted entities,  flow
steering rules attached through the wrapper on behalf of VFs must be
checked to make sure that their L2 specification relate to MAC address
assigned to that VF, and add L2 specification if its missing.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

To allow for usage of the flow steering Firmware structures in more locations over the driver,
such as the resource tracker, move them from mcg.c to common header files.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes a bug found by Nish Aravamudan
(https://lkml.org/lkml/2012/5/15/220) where the driver is not following
the spec (it is not aligning the rx buffer on a 16-byte boundary) and the
hypervisor aborts the registration, making the device unusable.

The fix follows BenH's recommendation (https://lkml.org/lkml/2012/7/20/461)
to replace the kmalloc+map for a single call to dma_alloc_coherent()
because that function always aligns to a 16-byte boundary.

The stable trees will run into this bug whenever the rx buffer kmalloc call
returns something not aligned on a 16-byte boundary.

Cc: <stable@vger.kernel.org>
Signed-off-by: Santiago Leon <santil@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

commit 144d56e9
("tcp: fix possible socket refcount problem") is missing
the IPv6 part. As tcp_release_cb is shared by both protocols
we should hold sock reference for the TCP_MTU_REDUCED_DEFERRED
bit.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Marc Kleine-Budde says:

====================
this patch is for the v3.6 release cycle. Benoît Locher fixed a repeated frame
bug in the mcp251x driver. He implemented the workaround suggested by the
errata sheet.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

While investigating l2tp bug, I hit a bug in eth_type_trans(),
because not enough bytes were pulled in skb head.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In znet_probe(), strncmp() may access beyond 0x100000 and
trigger the below oops in kvm.  Fix it by limiting the loop
under 0x100000-8. I suspect the limit could be further decreased
to 0x100000-sizeof(struct netidblk), however no datasheet at hand..

[    3.744312] BUG: unable to handle kernel paging request at 80100000
[    3.746145] IP: [<8119d12a>] strncmp+0xc/0x20
[    3.747446] *pde = 01d10067 *pte = 00100160
[    3.747493] Oops: 0000 [#1] DEBUG_PAGEALLOC
[    3.747493] Pid: 1, comm: swapper Not tainted 3.6.0-rc1-00018-g57bfc0a7 #73 Bochs Bochs
[    3.747493] EIP: 0060:[<8119d12a>] EFLAGS: 00010206 CPU: 0
[    3.747493] EIP is at strncmp+0xc/0x20
[    3.747493] EAX: 800fff4e EBX: 00000006 ECX: 00000006 EDX: 814d2bb9
[    3.747493] ESI: 80100000 EDI: 814d2bba EBP: 8e03dfa0 ESP: 8e03df98
[    3.747493]  DS: 007b ES: 007b FS: 0000 GS: 00e0 SS: 0068
[    3.747493] CR0: 8005003b CR2: 80100000 CR3: 016f7000 CR4: 00000690
[    3.747493] DR0: 00000000 DR1: 00000000 DR2: 00000000 DR3: 00000000
[    3.747493] DR6: ffff0ff0 DR7: 00000400
[    3.747493] Process swapper (pid: 1, ti=8e03c000 task=8e040000 task.ti=8e03c000)
[    3.747493] Stack:
[    3.747493]  800fffff 00000000 8e03dfb4 816a1376 00000006 816a134a 00000000 8e03dfd0
[    3.747493]  816819b5 816ed1c0 8e03dfe4 00000006 00000123 816ed604 8e03dfe4 81681b29
[    3.747493]  00000000 81681a5b 00000000 00000000 8134e542 00000000 00000000 00000000
[    3.747493] Call Trace:
[    3.747493]  [<816a1376>] znet_probe+0x2c/0x26b
[    3.747493]  [<816a134a>] ? dnet_driver_init+0xf/0xf
[    3.747493]  [<816819b5>] do_one_initcall+0x6a/0x110
[    3.747493]  [<81681b29>] kernel_init+0xce/0x14b
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ESN for esp is defined in RFC 4303. This RFC assumes that the
sequence number counters are always up to date. However,
this is not true if an async crypto algorithm is employed.

If the sequence number counters are not up to date on sequence
number check, we may incorrectly update the upper 32 bit of
the sequence number. This leads to a DOS.

We workaround this by comparing the upper sequence number,
(used for authentication) with the upper sequence number
computed after the async processing. We drop the packet
if these numbers are different.

To do this, we introduce a recheck function that does this
check in the ESN case.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixes following lockdep splat :

[ 1614.734896] =============================================
[ 1614.734898] [ INFO: possible recursive locking detected ]
[ 1614.734901] 3.6.0-rc3+ #782 Not tainted
[ 1614.734903] ---------------------------------------------
[ 1614.734905] swapper/11/0 is trying to acquire lock:
[ 1614.734907]  (slock-AF_INET){+.-...}, at: [<ffffffffa0209d72>] l2tp_xmit_skb+0x172/0xa50 [l2tp_core]
[ 1614.734920]
[ 1614.734920] but task is already holding lock:
[ 1614.734922]  (slock-AF_INET){+.-...}, at: [<ffffffff815fce23>] tcp_v4_err+0x163/0x6b0
[ 1614.734932]
[ 1614.734932] other info that might help us debug this:
[ 1614.734935]  Possible unsafe locking scenario:
[ 1614.734935]
[ 1614.734937]        CPU0
[ 1614.734938]        ----
[ 1614.734940]   lock(slock-AF_INET);
[ 1614.734943]   lock(slock-AF_INET);
[ 1614.734946]
[ 1614.734946]  *** DEADLOCK ***
[ 1614.734946]
[ 1614.734949]  May be due to missing lock nesting notation
[ 1614.734949]
[ 1614.734952] 7 locks held by swapper/11/0:
[ 1614.734954]  #0:  (rcu_read_lock){.+.+..}, at: [<ffffffff81592801>] __netif_receive_skb+0x251/0xd00
[ 1614.734964]  #1:  (rcu_read_lock){.+.+..}, at: [<ffffffff815d319c>] ip_local_deliver_finish+0x4c/0x4e0
[ 1614.734972]  #2:  (rcu_read_lock){.+.+..}, at: [<ffffffff8160d116>] icmp_socket_deliver+0x46/0x230
[ 1614.734982]  #3:  (slock-AF_INET){+.-...}, at: [<ffffffff815fce23>] tcp_v4_err+0x163/0x6b0
[ 1614.734989]  #4:  (rcu_read_lock){.+.+..}, at: [<ffffffff815da240>] ip_queue_xmit+0x0/0x680
[ 1614.734997]  #5:  (rcu_read_lock_bh){.+....}, at: [<ffffffff815d9925>] ip_finish_output+0x135/0x890
[ 1614.735004]  #6:  (rcu_read_lock_bh){.+....}, at: [<ffffffff81595680>] dev_queue_xmit+0x0/0xe00
[ 1614.735012]
[ 1614.735012] stack backtrace:
[ 1614.735016] Pid: 0, comm: swapper/11 Not tainted 3.6.0-rc3+ #782
[ 1614.735018] Call Trace:
[ 1614.735020]  <IRQ>  [<ffffffff810a50ac>] __lock_acquire+0x144c/0x1b10
[ 1614.735033]  [<ffffffff810a334b>] ? check_usage+0x9b/0x4d0
[ 1614.735037]  [<ffffffff810a6762>] ? mark_held_locks+0x82/0x130
[ 1614.735042]  [<ffffffff810a5df0>] lock_acquire+0x90/0x200
[ 1614.735047]  [<ffffffffa0209d72>] ? l2tp_xmit_skb+0x172/0xa50 [l2tp_core]
[ 1614.735051]  [<ffffffff810a69ad>] ? trace_hardirqs_on+0xd/0x10
[ 1614.735060]  [<ffffffff81749b31>] _raw_spin_lock+0x41/0x50
[ 1614.735065]  [<ffffffffa0209d72>] ? l2tp_xmit_skb+0x172/0xa50 [l2tp_core]
[ 1614.735069]  [<ffffffffa0209d72>] l2tp_xmit_skb+0x172/0xa50 [l2tp_core]
[ 1614.735075]  [<ffffffffa014f7f2>] l2tp_eth_dev_xmit+0x32/0x60 [l2tp_eth]
[ 1614.735079]  [<ffffffff81595112>] dev_hard_start_xmit+0x502/0xa70
[ 1614.735083]  [<ffffffff81594c6e>] ? dev_hard_start_xmit+0x5e/0xa70
[ 1614.735087]  [<ffffffff815957c1>] ? dev_queue_xmit+0x141/0xe00
[ 1614.735093]  [<ffffffff815b622e>] sch_direct_xmit+0xfe/0x290
[ 1614.735098]  [<ffffffff81595865>] dev_queue_xmit+0x1e5/0xe00
[ 1614.735102]  [<ffffffff81595680>] ? dev_hard_start_xmit+0xa70/0xa70
[ 1614.735106]  [<ffffffff815b4daa>] ? eth_header+0x3a/0xf0
[ 1614.735111]  [<ffffffff8161d33e>] ? fib_get_table+0x2e/0x280
[ 1614.735117]  [<ffffffff8160a7e2>] arp_xmit+0x22/0x60
[ 1614.735121]  [<ffffffff8160a863>] arp_send+0x43/0x50
[ 1614.735125]  [<ffffffff8160b82f>] arp_solicit+0x18f/0x450
[ 1614.735132]  [<ffffffff8159d9da>] neigh_probe+0x4a/0x70
[ 1614.735137]  [<ffffffff815a191a>] __neigh_event_send+0xea/0x300
[ 1614.735141]  [<ffffffff815a1c93>] neigh_resolve_output+0x163/0x260
[ 1614.735146]  [<ffffffff815d9cf5>] ip_finish_output+0x505/0x890
[ 1614.735150]  [<ffffffff815d9925>] ? ip_finish_output+0x135/0x890
[ 1614.735154]  [<ffffffff815dae79>] ip_output+0x59/0xf0
[ 1614.735158]  [<ffffffff815da1cd>] ip_local_out+0x2d/0xa0
[ 1614.735162]  [<ffffffff815da403>] ip_queue_xmit+0x1c3/0x680
[ 1614.735165]  [<ffffffff815da240>] ? ip_local_out+0xa0/0xa0
[ 1614.735172]  [<ffffffff815f4402>] tcp_transmit_skb+0x402/0xa60
[ 1614.735177]  [<ffffffff815f5a11>] tcp_retransmit_skb+0x1a1/0x620
[ 1614.735181]  [<ffffffff815f7e93>] tcp_retransmit_timer+0x393/0x960
[ 1614.735185]  [<ffffffff815fce23>] ? tcp_v4_err+0x163/0x6b0
[ 1614.735189]  [<ffffffff815fd317>] tcp_v4_err+0x657/0x6b0
[ 1614.735194]  [<ffffffff8160d116>] ? icmp_socket_deliver+0x46/0x230
[ 1614.735199]  [<ffffffff8160d19e>] icmp_socket_deliver+0xce/0x230
[ 1614.735203]  [<ffffffff8160d116>] ? icmp_socket_deliver+0x46/0x230
[ 1614.735208]  [<ffffffff8160d464>] icmp_unreach+0xe4/0x2c0
[ 1614.735213]  [<ffffffff8160e520>] icmp_rcv+0x350/0x4a0
[ 1614.735217]  [<ffffffff815d3285>] ip_local_deliver_finish+0x135/0x4e0
[ 1614.735221]  [<ffffffff815d319c>] ? ip_local_deliver_finish+0x4c/0x4e0
[ 1614.735225]  [<ffffffff815d3ffa>] ip_local_deliver+0x4a/0x90
[ 1614.735229]  [<ffffffff815d37b7>] ip_rcv_finish+0x187/0x730
[ 1614.735233]  [<ffffffff815d425d>] ip_rcv+0x21d/0x300
[ 1614.735237]  [<ffffffff81592a1b>] __netif_receive_skb+0x46b/0xd00
[ 1614.735241]  [<ffffffff81592801>] ? __netif_receive_skb+0x251/0xd00
[ 1614.735245]  [<ffffffff81593368>] process_backlog+0xb8/0x180
[ 1614.735249]  [<ffffffff81593cf9>] net_rx_action+0x159/0x330
[ 1614.735257]  [<ffffffff810491f0>] __do_softirq+0xd0/0x3e0
[ 1614.735264]  [<ffffffff8109ed24>] ? tick_program_event+0x24/0x30
[ 1614.735270]  [<ffffffff8175419c>] call_softirq+0x1c/0x30
[ 1614.735278]  [<ffffffff8100425d>] do_softirq+0x8d/0xc0
[ 1614.735282]  [<ffffffff8104983e>] irq_exit+0xae/0xe0
[ 1614.735287]  [<ffffffff8175494e>] smp_apic_timer_interrupt+0x6e/0x99
[ 1614.735291]  [<ffffffff81753a1c>] apic_timer_interrupt+0x6c/0x80
[ 1614.735293]  <EOI>  [<ffffffff810a14ad>] ? trace_hardirqs_off+0xd/0x10
[ 1614.735306]  [<ffffffff81336f85>] ? intel_idle+0xf5/0x150
[ 1614.735310]  [<ffffffff81336f7e>] ? intel_idle+0xee/0x150
[ 1614.735317]  [<ffffffff814e6ea9>] cpuidle_enter+0x19/0x20
[ 1614.735321]  [<ffffffff814e7538>] cpuidle_idle_call+0xa8/0x630
[ 1614.735327]  [<ffffffff8100c1ba>] cpu_idle+0x8a/0xe0
[ 1614.735333]  [<ffffffff8173762e>] start_secondary+0x220/0x222
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Check for an error from this and if so bail properly.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The vlan encapsulation fields in the maximum flow defintion were
never updated when the representation changed before upstreaming.
In theory this could cause a kernel panic when a maximum length
flow is used.  In practice this has never happened (to my knowledge)
because skb allocations are padded out to a cache line so you would
need the right combination of flow and packet being sent to userspace.
Signed-off-by: Jesse Gross <jesse@nicira.com>

hc has been allocated in this function and missing free it before
leaving from some error handling cases.

spatch with a semantic match is used to found this problem.
(http://coccinelle.lip6.fr/)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

When fq_codel builds a new flow, it should not reset codel state.

Codel algo needs to get previous values (lastcount, drop_next) to get
proper behavior.
Signed-off-by: Dave Taht <dave.taht@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Dave Taht <dave.taht@bufferbloat.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

The MCP2515 has a silicon bug causing repeated frame transmission, see section
5 of MCP2515 Rev. B Silicon Errata Revision G (March 2007).

Basically, setting TXBnCTRL.TXREQ in either SPI mode (00 or 11) will eventually
cause the bug. The workaround proposed by Microchip is to use mode 00 and send
a RTS command on the SPI bus to initiate the transmission.

Cc: <stable@vger.kernel.org>
Signed-off-by: Benoît Locher <Benoit.Locher@skf.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Suspending an open usbnet device results in constant
rescheduling of usbnet_bh.

commit 65841fd5 "usbnet: handle remote wakeup asap"
refactored the usbnet_bh code to allow sharing the
urb allocate and submit code with usbnet_resume. In
this process, a test for, and immediate return on,
ENOLINK from rx_submit was unintentionally dropped.

The rx queue will not grow if rx_submit fails,
making usbnet_bh reschedule itself.  This results
in a softirq storm if the error is persistent.
rx_submit translates the usb_submit_urb error
EHOSTUNREACH into ENOLINK, so this is an expected
and persistent error for a suspended device. The
old code tested for this condition and avoided
rescheduling.  Putting this test back.

Cc: <stable@vger.kernel.org> # v3.5
Cc: Ming Lei <ming.lei@canonical.com>
Cc: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>

SCTP charges wmem_alloc via sctp_set_owner_w() in sctp_sendmsg() and via
skb_set_owner_w() in sctp_packet_transmit(). If a sender runs out of
sndbuf it will sleep in sctp_wait_for_sndbuf() and expects to be waken up
by __sctp_write_space().

Buffer space charged via sctp_set_owner_w() is released in sctp_wfree()
which calls __sctp_write_space() directly.

Buffer space charged via skb_set_owner_w() is released via sock_wfree()
which calls sk->sk_write_space() _if_ SOCK_USE_WRITE_QUEUE is not set.
sctp_endpoint_init() sets SOCK_USE_WRITE_QUEUE on all sockets.

Therefore if sctp_packet_transmit() manages to queue up more than sndbuf
bytes, sctp_wait_for_sndbuf() will never be woken up again unless it is
interrupted by a signal.

This could be fixed by clearing the SOCK_USE_WRITE_QUEUE flag but ...

Charging for the data twice does not make sense in the first place, it
leads to overcharging sndbuf by a factor 2. Therefore this patch only
charges a single byte in wmem_alloc when transmitting an SCTP packet to
ensure that the socket stays alive until the packet has been released.

This means that control chunks are no longer accounted for in wmem_alloc
which I believe is not a problem as skb->truesize will typically lead
to overcharging anyway and thus compensates for any control overhead.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
CC: Vlad Yasevich <vyasevic@redhat.com>
CC: Neil Horman <nhorman@tuxdriver.com>
CC: David Miller <davem@davemloft.net>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sock_edemux() can handle either a regular socket or a timewait socket
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Joe Stringer <joe@wand.net.nz>
Signed-off-by: Jesse Gross <jesse@nicira.com>

Pull CIFS fixes from Steve French.

* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
  CIFS: Fix cifs_do_create error hadnling
  cifs: print error code if smb signature verification fails
  CIFS: Fix log messages in packet checking for SMB2
  CIFS: Protect i_nlink from being negative

Pull networking fixes from David Miller:

 1) NLA_PUT* --> nla_put_* conversion got one case wrong in
    nfnetlink_log, fix from Patrick McHardy.

 2) Missed error return check in ipw2100 driver, from Julia Lawall.

 3) PMTU updates in ipv4 were setting the expiry time incorrectly, fix
    from Eric Dumazet.

 4) SFC driver erroneously reversed src and dst when reporting filters
    via ethtool.

 5) Memory leak in CAN protocol and wrong setting of IRQF_SHARED in
    sja1000 can platform driver, from Alexey Khoroshilov and Sven
    Schmitt.

 6) Fix multicast traffic scaling regression in ipv4_dst_destroy, only
    take the lock when we really need to.  From Eric Dumazet.

 7) Fix non-root process spoofing in netlink, from Pablo Neira Ayuso.

 8) CWND reduction in TCP is done incorrectly during non-SACK recovery,
    fix from Yuchung Cheng.

 9) Revert netpoll change, and fix what was actually a driver specific
    problem.  From Amerigo Wang.  This should cure bootup hangs with
    netconsole some people reported.

10) Fix xen-netfront invoking __skb_fill_page_desc() with a NULL page
    pointer.  From Ian Campbell.

11) SIP NAT fix for expectiontation creation, from Pablo Neira Ayuso.

12) __ip_rt_update_pmtu() needs RCU locking, from Eric Dumazet.

13) Fix usbnet deadlock on resume, can't use GFP_KERNEL in this
    situation.  From Oliver Neukum.

14) The davinci ethernet driver triggers an OOPS on removal because it
    frees an MDIO object before unregistering it.  Fix from Bin Liu.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (41 commits)
  net: qmi_wwan: add several new Gobi devices
  fddi: 64 bit bug in smt_add_para()
  net: ethernet: fix kernel OOPS when remove davinci_mdio module
  net/xfrm/xfrm_state.c: fix error return code
  net: ipv6: fix error return code
  net: qmi_wwan: new device: Foxconn/Novatel E396
  usbnet: fix deadlock in resume
  cs89x0 : packet reception not working
  netfilter: nf_conntrack: fix racy timer handling with reliable events
  bnx2x: Correct the ndo_poll_controller call
  bnx2x: Move netif_napi_add to the open call
  ipv4: must use rcu protection while calling fib_lookup
  bnx2x: fix 57840_MF pci id
  net: ipv4: ipmr_expire_timer causes crash when removing net namespace
  e1000e: DoS while TSO enabled caused by link partner with small MSS
  l2tp: avoid to use synchronize_rcu in tunnel free function
  gianfar: fix default tx vlan offload feature flag
  netfilter: nf_nat_sip: fix incorrect handling of EBUSY for RTCP expectation
  xen-netfront: use __pskb_pull_tail to ensure linear area is big enough on RX
  netfilter: nfnetlink_log: fix error return code in init path
  ...

Gobi devices are composite, needing both the qcserial and
qmi_wwan drivers to support all functions.  Re-syncing the
list of supported devices with qcserial.

Cc: Aleksander Morgado <aleksander@lanedo.com>
Cc: Thomas Tuttle <ttuttle@chromium.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@tempietto.lan>

The intent was to set 4 bytes of data so that's why the sp_len is set
to 4 on the next line.  The cast to u_long pointer clears 8 bytes
on 64 bit arches.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@tempietto.lan>

Andreas Bombe reported that the added ktime_t overflow checking added to
timespec_valid in commit 4e8b1452 ("time: Improve sanity checking of
timekeeping inputs") was causing problems with X.org because it caused
timeouts larger then KTIME_T to be invalid.

Previously, these large timeouts would be clamped to KTIME_MAX and would
never expire, which is valid.

This patch splits the ktime_t overflow checking into a new
timespec_valid_strict function, and converts the timekeeping codes
internal checking to use this more strict function.
Reported-and-tested-by: Andreas Bombe <aeb@debian.org>
Cc: Zhouping Liu <zliu@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull KVM bugfixes from Marcelo Tosatti.

* git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: x86: fix KVM_GET_MSR for PV EOI
  kvm: Fix nonsense handling of compat ioctl

Pull PARISC fixes from James Bottomley:
 "This is a set of two bug fixes.  One is the ATOMIC problem which is
  now causing a compile failure in certain situations.  The other is
  mishandling of PER_LINUX32 which may also cause user visible effects.

  Signed-off-by: James Bottomley <JBottomley@Parallels.com>"

* tag 'parisc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/parisc-2.6:
  [PARISC] fix personality flag check in copy_thread()
  [PARISC] Redefine ATOMIC_INIT and ATOMIC64_INIT to drop the casts

Pull s390 fixes from Martin Schwidefsky:
 "A couple of s390 bug fixes for 3.5-rc4"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390/32: Don't clobber personality flags on exec
  s390/smp: add missing smp_store_status() for !SMP
  s390/dasd: fix ioctl return value
  s390: Always use "long" for ssize_t to match size_t

davinci mdio device is not unregistered from mdiobus when removing
the module, which causes BUG_ON() when free the device from mdiobus.

Calling mdiobus_unregister() before mdiobus_free() fixes the issue.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Initialize return variable before exiting on an error path.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
 { ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
    when != &ret
*if(...)
{
  ... when != ret = e2
      when forall
 return ret;
}

// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

Initialize return variable before exiting on an error path.

The initial initialization of the return variable is also dropped, because
that value is never used.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
 { ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
    when != &ret
*if(...)
{
  ... when != ret = e2
      when forall
 return ret;
}

// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

Foxconn-branded Novatel E396, Gobi3k modem.

Cc: Dan Williams <dcbw@redhat.com>
Cc: Bjørn Mork <bjorn@mork.no>
Cc: Ben Chan <benchan@google.com>
Signed-off-by: Aleksander Morgado <aleksander@lanedo.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>

A usbnet device can share a multifunction device
with a storage device. If the storage device is autoresumed
the usbnet devices also needs to be autoresumed. Allocating
memory with GFP_KERNEL can deadlock in this case.

This should go back into all kernels that have
commit 65841fd5
That is 3.5
Signed-off-by: Oliver Neukum <oneukum@suse.de>
CC: stable@kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

The RxCFG register of the CS89x0 could be configured incorrectly
(because of misplaced parentheses), resulting in the disabling
of packet reception.
Signed-off-by: Jaccon Bastiaansen <jaccon.bastiaansen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Existing code assumes that del_timer returns true for alive conntrack
entries. However, this is not true if reliable events are enabled.
In that case, del_timer may return true for entries that were
just inserted in the dying list. Note that packets / ctnetlink may
hold references to conntrack entries that were just inserted to such
list.

This patch fixes the issue by adding an independent timer for
event delivery. This increases the size of the ecache extension.
Still we can revisit this later and use variable size extensions
to allocate this area on demand.
Tested-by: Oliver Smith <olipro@8.c.9.b.0.7.4.0.1.0.0.2.ip6.arpa>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>