Rx descriptors queue length is hardware specific. Current common default
value is no more than an accident. So move Rx descriptor queue setup to
platform PCIe backend in the same way as it is already done for Tx.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Do not attempt to print frequency for an invalid channel
provided by firmware. That channel may simply not exist.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Fix merge artifact for commit 0b68fe10 ("qtnfmac: modify debugfs
to support multiple cards") and finally add debugfs support
for multiple qtnfmac wireless cards.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

KASAN reported use-after-free error:

[  995.220767] BUG: KASAN: use-after-free in qtnf_cmd_send_with_reply+0x169/0x3e0 [qtnfmac]
[  995.221098] Read of size 2 at addr ffff888213d1ded0 by task kworker/1:1/71

The issue in qtnf_cmd_send_with_reply impacts all the commands that do
not need response other then return code. For such commands, consume_skb
is used for response skb and right after that return code in response
skb is accessed.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

A number of people have reported the Edimax EW-7611ULB works fine.
Signed-off-by: Jes Sorensen <Jes.Sorensen@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

In commit 38506ece ("rtlwifi: rtl_pci: Start modification for
new drivers"), the flag that indicates that interrupts are enabled was
never set.

In addition, there are several places when enable/disable interrupts
were commented out are restored. A sychronize_interrupts() call is
removed.

Fixes: 38506ece ("rtlwifi: rtl_pci: Start modification for new drivers")
Cc: Stable <stable@vger.kernel.org>	# v3.18+
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

In commit 38506ece ("rtlwifi: rtl_pci: Start modification for
new drivers"), a callback needed to check if the hardware has released
a buffer indicating that a DMA operation is completed was not added.

Fixes: 38506ece ("rtlwifi: rtl_pci: Start modification for new drivers")
Cc: Stable <stable@vger.kernel.org>	# v3.18+
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

In commit 38506ece ("rtlwifi: rtl_pci: Start modification for
new drivers"), a callback to get the RX buffer address was added to
the PCI driver. Unfortunately, driver rtl8192de was not modified
appropriately and the code runs into a WARN_ONCE() call. The use
of an incorrect array is also fixed.

Fixes: 38506ece ("rtlwifi: rtl_pci: Start modification for new drivers")
Cc: Stable <stable@vger.kernel.org> # 3.18+
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Otherwise, the waiters (e.g., "modprobe rtwpci") will block forever.

Fixes: f530c196 ("rtw88: fix potential NULL pointer access for firmware")
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Acked-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Driver could access a NULL firmware pointer if we don't
return here.

Fixes: 5195b904 ("rtw88: avoid FW info flood")
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This leak was found by testing the EDIMAX EW-7612 on Raspberry Pi 3B+ with
Linux 5.4-rc5 (multi_v7_defconfig + rtlwifi + kmemleak) and noticed a
single memory leak during probe:

unreferenced object 0xec13ee40 (size 176):
  comm "kworker/u8:1", pid 36, jiffies 4294939321 (age 5580.790s)
  hex dump (first 32 bytes):
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
  backtrace:
    [<fc1bbb3e>] __netdev_alloc_skb+0x9c/0x164
    [<863dfa6e>] rtl92c_set_fw_rsvdpagepkt+0x254/0x340 [rtl8192c_common]
    [<9572be0d>] rtl92cu_set_hw_reg+0xf48/0xfa4 [rtl8192cu]
    [<116df4d8>] rtl_op_bss_info_changed+0x234/0x96c [rtlwifi]
    [<8933575f>] ieee80211_bss_info_change_notify+0xb8/0x264 [mac80211]
    [<d4061e86>] ieee80211_assoc_success+0x934/0x1798 [mac80211]
    [<e55adb56>] ieee80211_rx_mgmt_assoc_resp+0x174/0x314 [mac80211]
    [<5974629e>] ieee80211_sta_rx_queued_mgmt+0x3f4/0x7f0 [mac80211]
    [<d91091c6>] ieee80211_iface_work+0x208/0x318 [mac80211]
    [<ac5fcae4>] process_one_work+0x22c/0x564
    [<f5e6d3b6>] worker_thread+0x44/0x5d8
    [<82c7b073>] kthread+0x150/0x154
    [<b43e1b7d>] ret_from_fork+0x14/0x2c
    [<794dff30>] 0x0

It is because 8192cu doesn't implement usb_cmd_send_packet(), and this
patch just frees the skb within the function to resolve memleak problem
by now. Since 8192cu doesn't turn on fwctrl_lps that needs to download
command packet for firmware via the function, applying this patch doesn't
affect driver behavior.
Reported-by: Stefan Wahren <wahrenst@gmx.net>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

On 2019-10-28 06:07, wbob wrote:
> Hello Roman,
>
> while reading around drivers/net/wireless/ralink/rt2x00/rt2800lib.c
> I stumbled on what I think is an edit of yours made in error in march
> 2017:
>
> https://github.com/torvalds/linux/commit/41977e86#diff-dae5dc10da180f3b055809a48118e18aR5281
>
> RT6352 in line 5281 should not have been introduced as the "else if"
> below line 5291 can then not take effect for a RT6352 device. Another
> possibility is for line 5291 to be not for RT6352, but this seems
> very unlikely. Are you able to clarify still after this substantial time?
>
> 5277: static int rt2800_init_registers(struct rt2x00_dev *rt2x00dev)
> ...
> 5279:  } else if (rt2x00_rt(rt2x00dev, RT5390) ||
> 5280:         rt2x00_rt(rt2x00dev, RT5392) ||
> 5281:         rt2x00_rt(rt2x00dev, RT6352)) {
> ...
> 5291:  } else if (rt2x00_rt(rt2x00dev, RT6352)) {
> ...

Hence remove errornous line 5281 to make the driver actually
execute the correct initialization routine for MT7620 chips.

As it was requested by Stanislaw Gruszka remove setting values of
MIMO_PS_CFG and TX_PIN_CFG. MIMO_PS_CFG is responsible for MIMO
power-safe mode (which is disabled), hence we can drop setting it.
TX_PIN_CFG is set correctly in other functions, and as setting this
value breaks some devices, rather don't set it here during init, but
only modify it later on.

Fixes: 41977e86 ("rt2x00: add support for MT7620")
Reported-by: wbob <wbob@jify.de>
Reported-by: Roman Yeryomin <roman@advem.lv>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

drivers/net/wireless//realtek/rtl818x/rtl8180/rtl8225se.c:83:17: warning: 'rtl8225sez2_tx_power_cck' defined but not used [-Wunused-const-variable=]
drivers/net/wireless//realtek/rtl818x/rtl8180/rtl8225se.c:79:17: warning: 'rtl8225sez2_tx_power_cck_A' defined but not used [-Wunused-const-variable=]
drivers/net/wireless//realtek/rtl818x/rtl8180/rtl8225se.c:75:17: warning: 'rtl8225sez2_tx_power_cck_B' defined but not used [-Wunused-const-variable=]
drivers/net/wireless//realtek/rtl818x/rtl8180/rtl8225se.c:71:17: warning: 'rtl8225sez2_tx_power_cck_ch14' defined but not used [-Wunused-const-variable=]
drivers/net/wireless//realtek/rtl818x/rtl8180/rtl8225se.c:62:17: warning: 'rtl8225se_tx_power_ofdm' defined but not used [-Wunused-const-variable=]
drivers/net/wireless//realtek/rtl818x/rtl8180/rtl8225se.c:53:17: warning: 'rtl8225se_tx_power_cck_ch14' defined but not used [-Wunused-const-variable=]
drivers/net/wireless//realtek/rtl818x/rtl8180/rtl8225se.c:44:17: warning: 'rtl8225se_tx_power_cck' defined but not used [-Wunused-const-variable=]
drivers/net/wireless//realtek/rtl818x/rtl8180/rtl8225se.c:40:17: warning: 'rtl8225se_tx_gain_cck_ofdm' defined but not used [-Wunused-const-variable=]

They are never used, so can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:841:7: warning: variable free_pdu set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:842:30: warning: variable tx_rts_count set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:842:6: warning: variable tx_rts set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:843:7: warning: variable totlen set but not used [-Wunused-but-set-variable]

They are never used, so can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The LPS threshold was set to 2, means driver will leave LPS
mode if there is more than 2 frames TX/RX for every 2 seconds.
This makes driver enter/leave LPS frequently even if we just
"ping -i1" to the others.

Apparently we do not want to leave LPS mode if there is only
some background traffics or web surfing. By experiment, set
this to 50 is a more reasonable value to lower the over all
power consumption.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

local variable "ret" is not used. hence it is safe to remove and
just return 0.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

local variable "rc" is not used. It is safe to remove and
There is only one caller of libipw_qos_convert_ac_to_parameters().
hence make it void
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

ath.git patches for 5.5. Major changes:

wil6210

* add SPDX license identifiers

Merge tag 'wireless-drivers-next-2019-11-05' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next

Kalle Valo says:

====================
wireless-drivers-next patches for 5.5

First set of patches for 5.5. The most active driver here clearly is
rtw88, lots of patches for it. More quiet on other drivers, smaller
fixes and cleanups all over.

This pull request also has a trivial conflict, the report and example
resolution here:

https://lkml.kernel.org/r/20191031111242.50ab1eca@canb.auug.org.au

Major changes:

rtw88

* add deep power save support

* add mac80211 software tx queue (wake_tx_queue) support

* enable hardware rate control

* add TX-AMSDU support

* add NL80211_EXT_FEATURE_CAN_REPLACE_PTK0 support

* add power tracking support

* add 802.11ac beamformee support

* add set_bitrate_mask support

* add phy_info debugfs to show Tx/Rx physical status

* add RFE type 3 support for 8822b

ath10k

* add support for hardware rfkill on devices where firmware supports it

rtl8xxxu

* add bluetooth co-existence support for single antenna

iwlwifi

* Revamp the debugging infrastructure
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Simon Wunderlich says:

====================
This feature/cleanup patchset includes the following patches:

 - bump version strings, by Simon Wunderlich

 - Simplify batadv_v_ogm_aggr_list_free using skb_queue_purge,
   by Christophe Jaillet

 - Replace aggr_list_lock with lock free skb handlers,
   by Christophe Jaillet

 - explicitly mark fallthrough cases, by Sven Eckelmann

 - Drop lockdep.h include from soft-interface.c, by Sven Eckelmann
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

ThinkPad Thunderbolt 3 Dock Gen 2 is another docking station that uses
RTL8153 based USB ethernet.

The device supports macpassthru, but it failed to pass the test of -AD,
-BND and -BD. Simply bypass these tests since the device supports this
feature just fine.

Also the ACPI objects have some differences between Dell's and Lenovo's,
so make those ACPI infos no longer hardcoded.

BugLink: https://bugs.launchpad.net/bugs/1827961Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch implements reset_prepare and reset_done, which are used
for handling FLR.
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sudarsana Reddy Kalluru says:

====================
bnx2x/cnic: Enable Multi-Cos.

The patch series enables Multi-cos feature in the driver. This require
the use of new firmware 7.13.15.0.
Patch (1) adds driver changes to use new FW.
Patches (2) - (3) enables multi-cos functionality in bnx2x driver.
Patch (4) adds cnic driver change as required by new FW.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The new FW has added extra validation for HSI version to
make FW backward compatible with older VF drivers. Hence
set fp_hsi_ver to Fast Path HSI version of the FW in use.
Signed-off-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

PF driver doesn't enable tx-switching for all cos queues/clients,
which causes packets drop from PF to VF. Fix this by enabling
tx-switching on all cos queues/clients.
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

FW version 7.13.15 addresses the issue in Multi-cos implementation.
This patch re-enables the Multi-Cos support in the driver.

Fixes: d1f0b5dc ("bnx2x: Disable multi-cos feature.")
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 97a27d6d6e8d "bnx2x: Add FW 7.13.15.0" added said .bin FW to
linux-firmware tree. This FW addresses few important issues in the earlier
FW release.
This patch incorporates FW 7.13.15.0 in the bnx2x driver.
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pass a phy_interface_t to of_get_phy_mode(), by changing the type of
phy_mode in the device structure. This then requires that
zmii_attach() is also changes, since it takes a pointer to phy_mode.

Fixes: 0c65b2b9 ("net: of_get_phy_mode: Change API to solve int/unit warnings")
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Eric Dumazet says:

====================
net_sched: convert packet counters to 64bit

This small patch series add 64bit support for packet counts.

Fact that the counters were still 32bit has been quite painful.

tc -s -d qd sh dev eth0 | head -3
qdisc mq 1: root
 Sent 665706335338 bytes 6526520373 pkt (dropped 2441, overlimits 0 requeues 91)
 backlog 0b 0p requeues 91
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Now the kernel uses 64bit packet counters in scheduler layer,
we want to export these counters to user space.

Instead risking breaking user space by adding fields
to struct gnet_stats_basic, add a new TCA_STATS_PKT64.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After this change, qdisc packet counter is no longer
a 32bit quantity. We still export 32bit values to user.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

gnet_stats_basic_packed was really meant to be private kernel structure.

If this proves to be a problem, we will have to rename the in-kernel
version.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Andrew Lunn says:

====================
mv88e6xxx ATU occupancy as devlink resource

This patchset add generic support to DSA for devlink resources. The
Marvell switch Address Translation Unit occupancy is then exported as
a resource. In order to do this, the number of ATU entries is added to
the per switch info structure. Helpers are added, and then the
resource itself is then added.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The ATU can report how many entries it contains. It does this per bin,
there being 4 bins in total. Export the ATU as a devlink resource, and
provide a method the needed callback to get the resource occupancy.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When retrieving the ATU statistics, and ATU get next has to be
performed to trigger the ATU to collect the statistics. Export a
helper from global1_atu to perform this.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add helpers to set/get the ATU statistics register.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

For each supported switch, add an entry to the info structure for the
number of MACs which can be stored in the ATU. This will later be used
to export the ATU as a devlink resource, and indicate its occupancy,
how full the ATU is.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add wrappers around the devlink resource API, so that DSA drivers can
register and unregister devlink resources.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Florian Fainelli says:

====================
net: dsa: bcm_sf2: Add support for optional reset controller line

This patch series definest the optional reset controller line for the
BCM7445/BCM7278 integrated Ethernet switches and updates the driver to
drive that reset line in lieu of the internal watchdog based reset since
it does not work on BCM7278.

Changes in v2:
- make the reset_control_assert() conditional to BCM7278 in the remove
  function as well
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Grab an optional and exclusive reset controller line for the switch and
manage it during probe/remove functions accordingly. For 7278 devices we
change bcm_sf2_sw_rst() to use the reset controller line since the
WATCHDOG_CTRL register does not reset the switch contrary to stated
documentation.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>