Currently, bonding only obtain the timestamp (ts) information of
the active slave, which is available only for modes 1, 5, and 6.
For other modes, bonding only has software rx timestamping support.

However, some users who use modes such as LACP also want tx timestamp
support. To address this issue, let's check the ts information of each
slave. If all slaves support tx timestamping, we can enable tx
timestamping support for the bond.

Add a note that the get_ts_info may be called with RCU, or rtnl or
reference on the device in ethtool.h>
Suggested-by: Miroslav Lichvar <mlichvar@redhat.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Link: https://lore.kernel.org/r/20230418034841.2566262-1-liuhangbin@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Samin Guo says:

====================
Add Ethernet driver for StarFive JH7110 SoC

This series adds ethernet support for the StarFive JH7110 RISC-V SoC,
which includes a dwmac-5.20 MAC driver (from Synopsys DesignWare).
This series has been tested and works fine on VisionFive-2 v1.2A and
v1.3B SBC boards.

For more information and support, you can visit RVspace wiki[1].
You can simply review or test the patches at the link [2].
This patchset should be applied after the patchset [3] [4].

[1]: https://wiki.rvspace.org/
[2]: https://github.com/saminGuo/linux/tree/vf2-6.3rc4-gmac-net-next
[3]: https://patchwork.kernel.org/project/linux-riscv/cover/20230401111934.130844-1-hal.feng@starfivetech.com
[4]: https://patchwork.kernel.org/project/linux-riscv/cover/20230315055813.94740-1-william.qiu@starfivetech.com
====================

Link: https://lore.kernel.org/r/20230417100251.11871-1-samin.guo@starfivetech.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

dwmac supports multiple modess. When working under rmii and rgmii,
you need to set different phy interfaces.

According to the dwmac document, when working in rmii, it needs to be
set to 0x4, and rgmii needs to be set to 0x1.

The phy interface needs to be set in syscon, the format is as follows:
starfive,syscon: <&syscon, offset, shift>
Tested-by: Tommaso Merciai <tomm.merciai@gmail.com>
Signed-off-by: Samin Guo <samin.guo@starfivetech.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

This adds StarFive dwmac driver support on the StarFive JH7110 SoC.
Tested-by: Tommaso Merciai <tomm.merciai@gmail.com>
Co-developed-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Samin Guo <samin.guo@starfivetech.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Add documentation to describe StarFive dwmac driver(GMAC).
Signed-off-by: Yanhong Wang <yanhong.wang@starfivetech.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Samin Guo <samin.guo@starfivetech.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

According to:
stmmac_platform.c: stmmac_probe_config_dt
stmmac_main.c: stmmac_dvr_probe

dwmac controller may require one (stmmaceth) or two (stmmaceth+ahb)
reset signals, and the maxItems of resets/reset-names is going to be 2.

The gmac of Starfive Jh7110 SOC must have two resets.
it uses snps,dwmac-5.20 IP.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Samin Guo <samin.guo@starfivetech.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Add "snps,dwmac-5.20" compatible string for 5.20 version that can avoid
to define some platform data in the glue layer.
Tested-by: Tommaso Merciai <tomm.merciai@gmail.com>
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Samin Guo <samin.guo@starfivetech.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Add dwmac-5.20 IP version to snps.dwmac.yaml
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Samin Guo <samin.guo@starfivetech.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Heiner Kallweit says:

====================
r8169: use new macros from netdev_queues.h

Add one missing subqueue version of the macros, and use the new macros
in r8169 to simplify the code.
====================

Link: https://lore.kernel.org/r/7147a001-3d9c-a48d-d398-a94c666aa65b@gmail.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Use new net core macro netif_subqueue_completed_wake to simplify
the code of the tx cleanup path.
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Use new net core macro netif_subqueue_maybe_stop in the start_xmit path
to simplify the code. Whilst at it, set the tx queue start threshold to
twice the stop threshold. Before values were the same, resulting in
stopping/starting the queue more often than needed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Add netif_subqueue_completed_wake, complementing the subqueue versions
netif_subqueue_try_stop and netif_subqueue_maybe_stop.
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Vladimir Oltean says:

====================
Ocelot/Felix driver support for preemptible traffic classes

The series "Add tc-mqprio and tc-taprio support for preemptible traffic
classes" from:
https://lore.kernel.org/netdev/20230220122343.1156614-1-vladimir.oltean@nxp.com/

was eventually submitted in a form without the support for the
Ocelot/Felix switch driver. This patch set picks up that work again,
and presents a fairly modified form compared to the original.
====================

Link: https://lore.kernel.org/r/20230415170551.3939607-1-vladimir.oltean@nxp.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

In order to not transmit (preemptible) frames which will be received by
the link partner as corrupted (because it doesn't support FP), the
hardware requires the driver to program the QSYS_PREEMPTION_CFG_P_QUEUES
register only after the MAC Merge layer becomes active (verification
succeeds, or was disabled).

There are some cases when FP is known (through experimentation) to be
broken. Give priority to FP over cut-through switching, and disable FP
for known broken link modes.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The mqprio queue configuration can appear either through
TC_SETUP_QDISC_MQPRIO or through TC_SETUP_QDISC_TAPRIO. Make sure both
are treated in the same way.

Code does nothing new for now (except for rejecting multiple TXQs per
TC, which is a useless concept with DSA switches).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ferenc Fejes <fejes@inf.elte.hu>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

This doesn't apply anything to hardware and in general doesn't do
anything that the software variant doesn't do, except for checking that
there isn't more than 1 TXQ per TC (TXQs for a DSA switch are a dubious
concept anyway). The reason we add this is to be able to parse one more
field added to struct tc_mqprio_qopt_offload, namely preemptible_tcs.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ferenc Fejes <fejes@inf.elte.hu>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

ocelot_mm_update_port_status() updates mm->verify_status, but when the
verification state of a port changes, an IRQ isn't emitted, but rather,
only when the verification state reaches one of the final states (like
DISABLED, FAILED, SUCCEEDED) - things that would affect mm->tx_active,
which is what the IRQ *is* actually emitted for.

That is to say, user space may miss reports of an intermediary MAC Merge
verification state (like from INITIAL to VERIFYING), unless there was an
IRQ notifying the driver of the change in mm->tx_active as well.

This is not a huge deal, but for reliable reporting to user space, let's
call ocelot_mm_update_port_status() synchronously from
ocelot_port_get_mm(), which makes user space see the current MM status.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The MAC Merge IRQ of all ports is shared with the PTP TX timestamp IRQ
of all ports, which means that currently, when a PTP TX timestamp is
generated, felix_irq_handler() also polls for the MAC Merge layer status
of all ports, looking for changes. This makes the kernel do more work,
and under certain circumstances may make ptp4l require a
tx_timestamp_timeout argument higher than before.

Changes to the MAC Merge layer status are only to be expected under
certain conditions - its TX direction needs to be enabled - so we can
check early if that is the case, and omit register access otherwise.

Make ocelot_mm_update_port_status() skip register access if
mm->tx_enabled is unset, and also call it once more, outside IRQ
context, from ocelot_port_set_mm(), when mm->tx_enabled transitions from
true to false, because an IRQ is also expected in that case.

Also, a port may have its MAC Merge layer enabled but it may not have
generated the interrupt. In that case, there's no point in writing to
DEV_MM_STATUS to acknowledge that IRQ. We can reduce the number of
register writes per port with MM enabled by keeping an "ack" variable
which writes the "write-one-to-clear" bits. Those are 3 in number:
PRMPT_ACTIVE_STICKY, UNEXP_RX_PFRM_STICKY and UNEXP_TX_PFRM_STICKY.
The other fields in DEV_MM_STATUS are read-only and it doesn't matter
what is written to them, so writing zero is just fine.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Unfortunately, the workarounds for the hardware bugs make it pointless
to keep fine-grained locking for the MAC Merge state of each port.

Our vsc9959_cut_through_fwd() implementation requires
ocelot->fwd_domain_lock to be held, in order to serialize with changes
to the bridging domains and to port speed changes (which affect which
ports can be cut-through). Simultaneously, the traffic classes which can
be cut-through cannot be preemptible at the same time, and this will
depend on the MAC Merge layer state (which changes from threaded
interrupt context).

Since vsc9959_cut_through_fwd() would have to hold the mm->lock of all
ports for a correct and race-free implementation with respect to
ocelot_mm_irq(), in practice it means that any time a port's mm->lock is
held, it would potentially block holders of ocelot->fwd_domain_lock.

In the interest of simple locking rules, make all MAC Merge layer state
changes (and preemptible traffic class changes) be serialized by the
ocelot->fwd_domain_lock.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

When the switch emits an IRQ, we don't know what caused it, and we
iterate through all ports to check the MAC Merge status.

Move that iteration inside the ocelot lib; we will change the locking in
a future change and it would be good to encapsulate that lock completely
within the ocelot lib.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Song Yoong Siang says:

====================
XDP Rx HWTS metadata for stmmac driver

Implemented XDP receive hardware timestamp metadata for stmmac driver.

This patchset is tested with tools/testing/selftests/bpf/xdp_hw_metadata.
Below are the test steps and results.

Command on DUT:
	sudo ./xdp_hw_metadata <interface name>

Command on Link Partner:
	echo -n xdp | nc -u -q1 <destination IPv4 addr> 9091
	echo -n skb | nc -u -q1 <destination IPv4 addr> 9092

Result for port 9091:
	poll: 1 (0) skip=1 fail=0 redir=1
	xsk_ring_cons__peek: 1
	0x55f69f65f6d0: rx_desc[0]->addr=100000000008000 addr=8100 comp_addr=8000
	rx_timestamp: 1677762069053692631
	No rx_hash err=-95
	0x55f69f65f6d0: complete idx=8 addr=8000

Result for port 9092:
	poll: 1 (0) skip=2 fail=0 redir=1
	found skb hwtstamp = 1677762071.937207680
====================

Link: https://lore.kernel.org/r/20230415064503.3225835-1-yoong.siang.song@intel.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Add receive hardware timestamp metadata support via kfunc to XDP Zero Copy
receive packets.
Signed-off-by: Song Yoong Siang <yoong.siang.song@intel.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Add receive hardware timestamp metadata support via kfunc to XDP receive
packets.
Suggested-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Song Yoong Siang <yoong.siang.song@intel.com>
Acked-by: Stanislav Fomichev <sdf@google.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Introduce struct stmmac_xdp_buff as a preparation to support XDP Rx
metadata via kfuncs.
Signed-off-by: Song Yoong Siang <yoong.siang.song@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Leon Romanovsky says:

====================
Support tunnel mode in mlx5 IPsec packet offload

This series extends mlx5 to support tunnel mode in its IPsec packet
offload implementation.

v0: https://lore.kernel.org/all/cover.1681106636.git.leonro@nvidia.com
====================

Link: https://lore.kernel.org/r/cover.1681388425.git.leonro@nvidia.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Open mlx5 driver to accept IPsec tunnel mode.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Current hardware doesn't support double encapsulation which is
happening when IPsec packet offload tunnel mode is configured
together with eswitch encap option.

Any user attempt to add new SA/policy after he/she sets encap mode, will
generate the following FW syndrome:

 mlx5_core 0000:08:00.0: mlx5_cmd_out_err:803:(pid 1904): CREATE_FLOW_TABLE(0x930) op_mod(0x0) failed,
 status bad parameter(0x3), syndrome (0xa43321), err(-22)

Make sure that we block encap changes before creating flow steering tables.
This is applicable only for packet offload in tunnel mode, while packet
offload in transport mode and crypto offload, don't have such limitation
as they don't perform encapsulation.
Reviewed-by: Raed Salem <raeds@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Existing eswitch encap option enables header encapsulation. Unfortunately
currently available hardware isn't able to perform double encapsulation,
which can happen once IPsec packet offload tunnel mode is used together
with encap mode set to BASIC.

So as a solution for misconfiguration, provide an option to block encap
changes, which will be used for IPsec packet offload.
Reviewed-by: Emeel Hakim <ehakim@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In IPsec packet offload mode all header manipulations are performed by
hardware, which is responsible to add/remove L2 header with source and
destinations MACs.

CX-7 devices don't support offload of in-kernel routing functionality,
as such HW needs external help to fill other side MAC as it isn't
available for HW.

As a solution, let's listen to neigh ARP updates and reconfigure IPsec
rules on the fly once new MAC data information arrives.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Extend mlx5 driver with logic to support IPsec TX packet offload
in tunnel mode.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Extend mlx5 driver with logic to support IPsec RX packet offload
in tunnel mode.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Refactor setup_pkt_reformat() function to accommodate future extension
to support tunnel mode.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Create SA flow steering tables both for RX and TX with tunnel reformat
property. This allows to add and delete extra headers needed for tunnel
mode.
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Validate tunnel mode support for IPsec packet offload.
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Extend packet reformat types and flow table capabilities with
IPsec packet offload tunnel bits.
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

From time to time, it was observed that the nanosecond part of the
received timestamp, which is extracted from the IFH, it was actually
bigger than 1 second. So then when actually calculating the full
received timestamp, based on the nanosecond part from IFH and the second
part which is read from HW, it was actually wrong.

The issue seems to be inside the function lan966x_ifh_get, which
extracts information from an IFH(which is an byte array) and returns the
value in a u64. When extracting the timestamp value from the IFH, which
starts at bit 192 and have the size of 32 bits, then if the most
significant bit was set in the timestamp, then this bit was extended
then the return value became 0xffffffff... . And the reason of this is
because constants without any postfix are treated as signed longs and
that is the reason why '1 << 31' becomes 0xffffffff80000000.
This is fixed by adding the postfix 'ULL' to 1.

Fixes: fd762783 ("net: lan966x: Stop using packing library")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Xin Long says:

====================
sctp: add some missing peer_capables in sctp info dump

The 1st patch removes the unused and obsolete hostname_address from
sctp_association peer and also the bit from sctp_info peer_capables,
and then reuses its bit for reconf_capable and use the higher
available bit for intl_capable in the 2nd patch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

There are two new peer capables have been added since sctp_diag was
introduced into SCTP. When dumping the peer capables, these two new
peer capables should also be included. To not break the old capables,
reconf_capable takes the old hostname_address bit, and intl_capable
uses the higher available bit in sctpi_peer_capable.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the latest RFC9260, the Host Name Address param has been deprecated.
For INIT chunk:

  Note 3: An INIT chunk MUST NOT contain the Host Name Address
  parameter.  The receiver of an INIT chunk containing a Host Name
  Address parameter MUST send an ABORT chunk and MAY include an
  "Unresolvable Address" error cause.

For Supported Address Types:

  The value indicating the Host Name Address parameter MUST NOT be
  used when sending this parameter and MUST be ignored when receiving
  this parameter.

Currently Linux SCTP doesn't really support Host Name Address param,
but only saves some flag and print debug info, which actually won't
even be triggered due to the verification in sctp_verify_param().
This patch is to delete those dead code.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Matthieu Baerts says:

====================
mptcp: various small cleanups

Patch 1 makes a function static because it is only used in one file.

Patch 2 adds info about the git trees we use to help occasional devs.

Patch 3 removes an unused variable.

Patch 4 removes duplicated entries from the help menu of a tool used in
MPTCP selftests.

Patch 5 removes some ShellCheck warnings in mptcp_join.sh selftest.

Only very minor improvements then.
====================
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>