As CAN FD offers a second bitrate for the data section of the CAN frame the
infrastructure for storing and configuring this second bitrate is introduced.
Improved the readability of the if-statement by inserting some newlines.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

As the bittiming calculation functions are to be used with different
bittiming_const structures for CAN and CAN FD the direct reference to
priv->bittiming_const inside these functions has to be removed.

Also moved the check for existing bittiming const to one place.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

This patch moves a sanity check in order to have a second user for CAN FD.
Also simplify the return value generation in can_get_bittiming() as only
correct return values of can_[calc|fixup]_bittiming() lead to a return value of
zero.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

When setting the bitrate both can_calc_bittiming() and can_fixup_bittiming()
lead to the bitrate variable to be set, when a proper bit timing is available.
Only then the bitrate configuration is stored for the device, so checking for
priv->bittiming.bitrate is always sufficient.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

The skbuff protocol value was formerly fixed/sanitized to ETH_P_CAN in
can_put_echo_skb(). With CAN FD this value has to be preserved.
This patch changes the hard assignment of the protocol value to a check of
valid protocol values for CAN and CAN FD.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

This patch converts the dev_<level> printing to netdev_<level>, this makes it
possible to remove the "struct device *dev" pointer from the "struct
ican3_dev".

Cc: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

This patch replaces an open coded pdev->id_entry by platform_get_device_id().
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

This patch removes #ifdef CONFIG_PM_SLEEP to improve compile coverage.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

This patch removes #ifdef CONFIG_PM_SLEEP to improve compile coverage.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

This patch moves one diagnostic message used for debugging purposes
to dev_dbg() and removes one useless message.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Make local functions static (ie. only used in bond_options.c)
Make bond options parsing tables constant.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

These functions are defined but no longer used.
Compile tested only.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Reviewed-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Can be invoked from non-BH context.

Based upon a patch by Eric Dumazet.

Fixes: f19c29e3 ("tcp: snmp stats for Fast Open, SYN rtx, and data pkts")
Reported-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently we're using GFP_KERNEL, however there are some path(s) where we
can hold some spinlocks, specifically bond->curr_slave_lock:

[    4.722916] BUG: sleeping function called from invalid context at mm/slub.c:965
[    4.724438] in_atomic(): 1, irqs_disabled(): 0, pid: 940, name: ifup-eth
[    4.726034] 5 locks held by ifup-eth/940:
...snip...
[    4.734646]  #4:  (&bond->curr_slave_lock){+...+.}, at: [<ffffffffa00badc6>] bond_enslave+0xda6/0xdd0 [bonding]
...snip...
[    4.759081]  [<ffffffffa00b6f11>] bond_change_active_slave+0x191/0x3b0 [bonding]
[    4.760917]  [<ffffffffa00b7227>] bond_select_active_slave+0xf7/0x1d0 [bonding]
[    4.762751]  [<ffffffffa00badce>] bond_enslave+0xdae/0xdd0 [bonding]
...snip...

As it's out of hot path and is a really rare event - change the gfp_t flags
to GFP_ATOMIC to avoid sleeping under spinlock.

v2: convert new notify calls to GFP_ATOMIC.

CC: Thomas Glanzmann <thomas@glanzmann.de>
CC: Ding Tianhong <dingtianhong@huawei.com>
CC: Jay Vosburgh <fubar@us.ibm.com>
CC: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit e688a604 ("net: introduce DST_NOPEER dst flag") introduced
DST_NOPEER because because of crashes in ipv6_select_ident called from
udp6_ufo_fragment.

Since commit 916e4cf4 ("ipv6: reuse ip6_frag_id from
ip6_ufo_append_data") we don't call ipv6_select_ident any more from
ip6_ufo_append_data, thus this flag lost its purpose and can be removed.

Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Hayes Wang says:

====================
r8152: cleanups

Deal with some empty lines and spaces, replace some tp->netdev with netdev,
and remove the unnecessary function.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The rtl8152_get_stats() returns the point address of the struct
net_device_stats. This could be got from struct net_device directly.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Replace some tp->netdev with netdev.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add or remove some empty lines. Replace the spaces with the tabs.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Conflicts:
	drivers/net/wireless/ath/ath9k/recv.c
	drivers/net/wireless/mwifiex/pcie.c
	net/ipv6/sit.c

The SIT driver conflict consists of a bug fix being done by hand
in 'net' (missing u64_stats_init()) whilst in 'net-next' a helper
was created (netdev_alloc_pcpu_stats()) which takes care of this.

The two wireless conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes some whitespace issues in Kconfig files of IEEE
802.15.4 subsytem.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since commit 8fad346f
(ieee802154: add basic support for RF212 to at86rf230 driver)

we support at86rf212 as well.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver currently maps a page for DMA, divides the page into multiple
frags and posts them to the HW. It un-maps the page after data is received
on all the frags of the page. This scheme doesn't work when bounce buffers
are used for DMA (swiotlb=force kernel param).

This patch fixes this problem by calling dma_sync_single_for_cpu() for each
frag (excepting the last one) so that the data is copied from the bounce
buffers. The page is un-mapped only when DMA finishes on the last frag of
the page.
(Thanks Ben H. for suggesting the dma_sync API!)

This patch also renames the "last_page_user" field of be_rx_page_info{}
struct to "last_frag" to improve readability of the fixed code.
Reported-by: Li Fengmao <li.fengmao@zte.com.cn>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Simon Wunderlich says:

====================
this series contains a header file proposal for MPLS labels. These
labels do not seem to be properly defined in the kernel so far. We are
developing a wired/wireless 802.21/MPLS switch and need to check the
MPLS labels to use the traffic control info for transmissions over
802.11 networks.

Changes to third version:

 * rename mpls_label_stack to mpls_label (thanks Neil)
 * fix over-indendented closing brac (thanks Sergei)
 * add Johannes' Ack
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

MPLS labels may contain traffic control information, which should be
evaluated and used by the wireless subsystem if present.

Also check for IEEE 802.21 which is always network control traffic.
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Labels for the Multiprotocol Label Switching are defined in RFC 3032
which was superseded by RFC 5462. Add the definition to UAPI and a stub
header for include/linux.
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the Ethertype for IEEE Std 802.21 - Media Independent Handover
Protocol. This Ethertype is used for network control messages.
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull networking fixes from David Miller:

 1) Fix memory leak in ieee80211_prep_connection(), sta_info leaked on
    error.  From Eytan Lifshitz.

 2) Unintentional switch case fallthrough in nft_reject_inet_eval(),
    from Patrick McHardy.

 3) Must check if payload lenth is a power of 2 in
    nft_payload_select_ops(), from Nikolay Aleksandrov.

 4) Fix mis-checksumming in xen-netfront driver, ip_hdr() is not in the
    correct place when we invoke skb_checksum_setup().  From Wei Liu.

 5) TUN driver should not advertise HW vlan offload features in
    vlan_features.  Fix from Fernando Luis Vazquez Cao.

 6) IPV6_VTI needs to select NET_IPV_TUNNEL to avoid build errors, fix
    from Steffen Klassert.

 7) Add missing locking in xfrm_migrade_state_find(), we must hold the
    per-namespace xfrm_state_lock while traversing the lists.  Fix from
    Steffen Klassert.

 8) Missing locking in ath9k driver, access to tid->sched must be done
    under ath_txq_lock().  Fix from Stanislaw Gruszka.

 9) Fix two bugs in TCP fastopen.  First respect the size argument given
    to tcp_sendmsg() in the fastopen path, and secondly prevent
    tcp_send_syn_data() from potentially using order-5 allocations.
    From Eric Dumazet.

10) Fix handling of default neigh garbage collection params, from Jiri
    Pirko.

11) Fix cwnd bloat and over-inflation of RTT when transmit segmentation
    is in use.  From Eric Dumazet.

12) Missing initialization of Realtek r8169 driver's statistics
    seqlocks.  Fix from Kyle McMartin.

13) Fix RTNL assertion failures in 802.3ad and AB ARP monitor of bonding
    driver, from Ding Tianhong.

14) Bonding slave release race can cause divide by zero, fix from
    Nikolay Aleksandrov.

15) Overzealous return from neigh_periodic_work() causes reachability
    time to not be computed.  Fix from Duain Jiong.

16) Fix regression in ipv6_find_hdr(), it should not return -ENOENT when
    a specific target is specified and found.  From Hans Schillstrom.

17) Fix VLAN tag stripping regression in BNA driver, from Ivan Vecera.

18) Tail loss probe can calculate bogus RTTs due to missing packet
    marking on retransmit.  Fix from Yuchung Cheng.

19) We cannot do skb_dst_drop() in iptunnel_pull_header() because
    multicast loopback detection in later code paths need access to
    skb_rtable().  Fix from Xin Long.

20) The macvlan driver regresses in that it propagates lower device
    offload support disables into itself, causing severe slowdowns when
    running over a bridge.  Provide the software offloads always on
    macvlan devices to deal with this and the regression is gone.  From
    Vlad Yasevich.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (103 commits)
  macvlan: Add support for 'always_on' offload features
  net: sctp: fix sctp_sf_do_5_1D_ce to verify if we/peer is AUTH capable
  ip_tunnel:multicast process cause panic due to skb->_skb_refdst NULL pointer
  net: cpsw: fix cpdma rx descriptor leak on down interface
  be2net: isolate TX workarounds not applicable to Skyhawk-R
  be2net: Fix skb double free in be_xmit_wrokarounds() failure path
  be2net: clear promiscuous bits in adapter->flags while disabling promiscuous mode
  be2net: Fix to reset transparent vlan tagging
  qlcnic: dcb: a couple off by one bugs
  tcp: fix bogus RTT on special retransmission
  hsr: off by one sanity check in hsr_register_frame_in()
  can: remove CAN FD compatibility for CAN 2.0 sockets
  can: flexcan: factor out soft reset into seperate funtion
  can: flexcan: flexcan_remove(): add missing netif_napi_del()
  can: flexcan: fix transition from and to freeze mode in chip_{,un}freeze
  can: flexcan: factor out transceiver {en,dis}able into seperate functions
  can: flexcan: fix transition from and to low power mode in chip_{en,dis}able
  can: flexcan: flexcan_open(): fix error path if flexcan_chip_start() fails
  can: flexcan: fix shutdown: first disable chip, then all interrupts
  USB AX88179/178A: Support D-Link DUB-1312
  ...

Pull regulator fixes from Mark Brown:
 "A couple of fixes here which ensure that regulators using the core
  support for GPIO enables work in all cases by ensuring that helpers
  are used consistently rather than open coding in places and hence not
  having GPIO support in some of them"

* tag 'regulator-v3.14-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
  regulator: core: Replace direct ops->disable usage
  regulator: core: Replace direct ops->enable usage

Merge misc fixes from Andrew Morton.

* emailed patches from Andrew Morton akpm@linux-foundation.org>:
  mm: page_alloc: exempt GFP_THISNODE allocations from zone fairness
  mm: numa: bugfix for LAST_CPUPID_NOT_IN_PAGE_FLAGS
  MAINTAINERS: add and correct types of some "T:" entries
  MAINTAINERS: use tab for separator
  rapidio/tsi721: fix tasklet termination in dma channel release
  hfsplus: fix remount issue
  zram: avoid null access when fail to alloc meta
  sh: prefix sh-specific "CCR" and "CCR2" by "SH_"
  ocfs2: fix quota file corruption
  drivers/rtc/rtc-s3c.c: fix incorrect way of save/restore of S3C2410_TICNT for TYPE_S3C64XX
  kallsyms: fix absolute addresses for kASLR
  scripts/gen_initramfs_list.sh: fix flags for initramfs LZ4 compression
  mm: include VM_MIXEDMAP flag in the VM_SPECIAL list to avoid m(un)locking
  memcg: reparent charges of children before processing parent
  memcg: fix endless loop in __mem_cgroup_iter_next()
  lib/radix-tree.c: swapoff tmpfs radix_tree: remember to rcu_read_unlock
  dma debug: account for cachelines and read-only mappings in overlap tracking
  mm: close PageTail race
  MAINTAINERS: EDAC: add Mauro and Borislav as interim patch collectors

Jan Stancek reports manual page migration encountering allocation
failures after some pages when there is still plenty of memory free, and
bisected the problem down to commit 81c0a2bb ("mm: page_alloc: fair
zone allocator policy").

The problem is that GFP_THISNODE obeys the zone fairness allocation
batches on one hand, but doesn't reset them and wake kswapd on the other
hand.  After a few of those allocations, the batches are exhausted and
the allocations fail.

Fixing this means either having GFP_THISNODE wake up kswapd, or
GFP_THISNODE not participating in zone fairness at all.  The latter
seems safer as an acute bugfix, we can clean up later.
Reported-by: Jan Stancek <jstancek@redhat.com>
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Rik van Riel <riel@redhat.com>
Acked-by: Mel Gorman <mgorman@suse.de>
Cc: <stable@kernel.org>		[3.12+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

When doing some numa tests on powerpc, I triggered an oops bug.  I find
it is caused by using page->_last_cpupid.  It should be initialized as
"-1 & LAST_CPUPID_MASK", but not "-1".  Otherwise, in task_numa_fault(),
we will miss the checking (last_cpupid == (-1 & LAST_CPUPID_MASK)).  And
finally cause an oops bug in task_numa_group(), since the online cpu is
less than possible cpu.  This happen with CONFIG_SPARSE_VMEMMAP disabled

Call trace:

  SMP NR_CPUS=64 NUMA PowerNV
  Modules linked in:
  CPU: 24 PID: 804 Comm: systemd-udevd Not tainted3.13.0-rc1+ #32
  task: c000001e2746aa80 ti: c000001e32c50000 task.ti:c000001e32c50000
  REGS: c000001e32c53510 TRAP: 0300   Not tainted(3.13.0-rc1+)
  MSR: 9000000000009032 <SF,HV,EE,ME,IR,DR,RI>  CR:28024424  XER: 20000000
  CFAR: c000000000009324 DAR: 7265717569726857 DSISR:40000000 SOFTE: 1
  NIP  .task_numa_fault+0x1470/0x2370
  LR  .task_numa_fault+0x1468/0x2370
  Call Trace:
   .task_numa_fault+0x1468/0x2370 (unreliable)
   .do_numa_page+0x480/0x4a0
   .handle_mm_fault+0x4ec/0xc90
   .do_page_fault+0x3a8/0x890
   handle_page_fault+0x10/0x30
  Instruction dump:
  3c82fefb 3884b138 48d9cff1 60000000 48000574 3c62fefb3863af78 3c82fefb
  3884b138 48d9cfd5 60000000 e93f0100 <812902e4> 7d2907b45529063e 7d2a07b4
  ---[ end trace 15f2510da5ae07cf ]---
Signed-off-by: Liu Ping Fan <pingfank@linux.vnet.ibm.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Tree location entries should start with the appropriate type.

Add git to some, hg to another.

Neaten tree type description.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Convert whitespace to single tab for separators.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This patch is a modification of the patch originally proposed by
Xiaotian Feng <xtfeng@gmail.com>: https://lkml.org/lkml/2012/11/5/413
This new version disables DMA channel interrupts and ensures that the
tasklet wil not be scheduled again before calling tasklet_kill().

Unfortunately the updated patch was not released at that time due to
planned rework of Tsi721 mport driver to use threaded interrupts (which
has yet to happen).  Recently the issue was reported again:
https://lkml.org/lkml/2014/2/19/762.

Description from the original Xiaotian's patch:

 "Some drivers use tasklet_disable in device remove/release process,
  tasklet_disable will inc tasklet->count and return.  If the tasklet is
  not handled yet under some softirq pressure, the tasklet will be
  placed on the tasklet_vec, never have a chance to be excuted.  This
  might lead to a heavy loaded ksoftirqd, wakeup with pending_softirq,
  but tasklet is disabled.  tasklet_kill should be used in this case."

This patch is applicable to kernel versions starting from v3.5.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Xiaotian Feng <xtfeng@gmail.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Mike Galbraith <bitbucket@online.de>
Cc: <stable@vger.kernel.org>	[3.5+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Current implementation of HFS+ driver has small issue with remount
option.  Namely, for example, you are unable to remount from RO mode
into RW mode by means of command "mount -o remount,rw /dev/loop0
/mnt/hfsplus".  Trying to execute sequence of commands results in an
error message:

  mount /dev/loop0 /mnt/hfsplus
  mount -o remount,ro /dev/loop0 /mnt/hfsplus
  mount -o remount,rw /dev/loop0 /mnt/hfsplus

  mount: you must specify the filesystem type

  mount -t hfsplus -o remount,rw /dev/loop0 /mnt/hfsplus

  mount: /mnt/hfsplus not mounted or bad option

The reason of such issue is failure of mount syscall:

  mount("/dev/loop0", "/mnt/hfsplus", 0x2282a60, MS_MGC_VAL|MS_REMOUNT, NULL) = -1 EINVAL (Invalid argument)

Namely, hfsplus_parse_options_remount() method receives empty "input"
argument and return false in such case.  As a result, hfsplus_remount()
returns -EINVAL error code.

This patch fixes the issue by means of return true for the case of empty
"input" argument in hfsplus_parse_options_remount() method.
Signed-off-by: Vyacheslav Dubeyko <slava@dubeyko.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

zram_meta_alloc could fail so caller should check it.  Otherwise, your
system will hang.
Signed-off-by: Minchan Kim <minchan@kernel.org>
Acked-by: Jerome Marchand <jmarchan@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Commit bcf24e1d ("mmc: omap_hsmmc: use the generic config for
omap2plus devices"), enabled the build for other platforms for compile
testing.

sh-allmodconfig now fails with:

    include/linux/omap-dma.h:171:8: error: expected identifier before numeric constant
    make[4]: *** [drivers/mmc/host/omap_hsmmc.o] Error 1

This happens because SuperH #defines "CCR", which is one of the enum
values in include/linux/omap-dma.h.  There's a similar issue with "CCR2"
on sh2a.

As "CCR" and "CCR2" are too generic names for global #defines, prefix
them with "SH_" to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Global quota files are accessed from different nodes.  Thus we cannot
cache offset of quota structure in the quota file after we drop our node
reference count to it because after that moment quota structure may be
freed and reallocated elsewhere by a different node resulting in
corruption of quota file.

Fix the problem by clearing dq_off when we are releasing dquot structure.
We also remove the DB_READ_B handling because it is useless -
DQ_ACTIVE_B is set iff DQ_READ_B is set.
Signed-off-by: Jan Kara <jack@suse.cz>
Cc: Goldwyn Rodrigues <rgoldwyn@suse.de>
Cc: Joel Becker <jlbec@evilplan.org>
Reviewed-by: Mark Fasheh <mfasheh@suse.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

On exynos5250, exynos5420 and exynos5260 it was observed that, after 1
cycle of S2R, the rtc-tick occurs at a very fast rate as compared to the
rtc-tick occuring before S2R.

This patch fixes the above issue by correcting the wrong way of
save/restore of S3C2410_TICNT for TYPE_S3C64XX.
Signed-off-by: Vikas Sajjan <vikas.sajjan@samsung.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>