In ipv4_mtu there is some logic where we are testing for a non-zero value
and a timer expiration, then setting the value to zero, and then testing if
the value is zero we set it to a value based on the dst.  Instead of
bothering with the extra steps it is easier to just cleanup the logic so
that we set it to the dst based value if it is zero or if the timer has
expired.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>

At commit 07d106d0, Linus pointed out that ENOIOCTLCMD should be
translated as ENOTTY to user mode.

Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch moves calls to ioremap and request_mem_region to
devm_request_and_ioremap call.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch removes bus_id from mdio platform data, The reason to remove
bus_id is, stmmac mdio bus_id is always same as stmmac bus-id, so there
is no point in passing this in different variable.
Also stmmac ethernet driver connects to phy with bus_id passed its
platform data.
So, having single bus-id is much simpler.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes stmmac_pltfr_remove function, which is broken because,
it is accessing plat variable via freed memory priv pointer which gets
freed by free_netdev called from stmmac_dvr_remove.

In short this patch caches the plat pointer in local variable before
calling stmmac_dvr_remove to prevent code accessing freed memory.

Without this patch any attempt to remove the stmmac device will fail as
below:

Unregistering eth 0 ...
Unable to handle kernel paging request at virtual address 6b6b6bab
pgd = de5dc000
[6b6b6bab] *pgd=00000000
Internal error: Oops: 5 [#1] PREEMPT SMP
Modules linked in: cdev(O+)
CPU: 0    Tainted: G           O  (3.3.1_stm24_0210-b2000+ #25)
PC is at stmmac_pltfr_remove+0x2c/0xa0
LR is at stmmac_pltfr_remove+0x28/0xa0
pc : [<c01b8908>]    lr : [<c01b8904>]    psr: 60000013
sp : def6be78  ip : de6c5a00  fp : 00000000
r10: 00000028  r9 : c082d81d  r8 : 00000001
r7 : de65a600  r6 : df81b240  r5 : c0413fd8  r4 : 00000000
r3 : 6b6b6b6b  r2 : def6be6c  r1 : c0355e2b  r0 : 00000020
Flags: nZCv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment user
Control: 10c53c7d  Table: 5e5dc04a  DAC: 00000015
Process insmod (pid: 738, stack limit = 0xdef6a2f0)
Stack: (0xdef6be78 to 0xdef6c000)
be60:                                                       c0413fe0
c0403658
be80: c0400bb0 c019270c c01926f8 c0191478 00000000 c0414014 c0413fe0
c01914d8
bea0: 00000000 c0413fe0 df8045d0 c019109c c0413fe0 c0400bf0 c0413fd8
c018f04c
bec0: 00000000 bf000000 c0413fd8 c01929a0 c0413fd8 bf000000 00000000
c0192bfc
bee0: bf00009c bf000014 def6a000 c000859c 00000000 00000001 bf00009c
bf00009c
bf00: 00000001 bf00009c 00000001 bf0000e4 de65a600 00000001 c082d81d
c0058cd0
bf20: bf0000a8 c004fbd8 c0056414 c082d815 c02aea20 bf0001f0 00b0b008
e0846208
bf40: c03ec8a0 e0846000 0000db0d e0850604 e08504de e0853a24 00000204
000002d4
bf60: 00000000 00000000 0000001c 0000001d 00000009 00000000 00000006
00000000
bf80: 00000003 f63d4e2e 0000db0d bef02ed8 00000080 c000d2e8 def6a000
00000000
bfa0: 00000000 c000d140 f63d4e2e 0000db0d 00b0b018 0000db0d 00b0b008
b6f4f298
bfc0: f63d4e2e 0000db0d bef02ed8 00000080 00000003 00000000 00010000
00000000
bfe0: 00b0b008 bef02c64 00008d20 b6ef3784 60000010 00b0b018 5a5a5a5a
5a5a5a5a
[<c01b8908>] (stmmac_pltfr_remove+0x2c/0xa0) from [<c019270c>]
(platform_drv_remove+0x14/0x18)
[<c019270c>] (platform_drv_remove+0x14/0x18) from [<c0191478>]
(__device_release_driver+0x64/0xa4)
[<c0191478>] (__device_release_driver+0x64/0xa4) from [<c01914d8>]
(device_release_driver+0x20/0x2c)
[<c01914d8>] (device_release_driver+0x20/0x2c) from [<c019109c>]
(bus_remove_device+0xcc/0xdc)
[<c019109c>] (bus_remove_device+0xcc/0xdc) from [<c018f04c>]
(device_del+0x104/0x160)
[<c018f04c>] (device_del+0x104/0x160) from [<c01929a0>]
(platform_device_del+0x18/0x58)
[<c01929a0>] (platform_device_del+0x18/0x58) from [<c0192bfc>]
(platform_device_unregister+0xc/0x18)
[<c0192bfc>] (platform_device_unregister+0xc/0x18) from [<bf000014>]
(r_init+0x14/0x2c [cdev])
[<bf000014>] (r_init+0x14/0x2c [cdev]) from [<c000859c>]
(do_one_initcall+0x90/0x160)
[<c000859c>] (do_one_initcall+0x90/0x160) from [<c0058cd0>]
(sys_init_module+0x15c4/0x1794)
[<c0058cd0>] (sys_init_module+0x15c4/0x1794) from [<c000d140>]
(ret_fast_syscall+0x0/0x30)
Code: e1a04000 e59f0070 eb039b65 e59636e4 (e5933040)
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds a basic check in stmmac_mdio_unregister to see if mdio
bus registeration for this driver was actually sucessfull or not.

Use case here is, if BSP considers using mdio-gpio bus along with stmmac
driver by passing mdio_bus_data as NULL in platform data.
Call to stmmac_mdio_register with mdio_bus_data as NULL returns 0, which
is a considered sucessfull call form stmmac. Then again when we unload
the driver we just call stmmac_mdio_unregister, this is were the actual
problem is stmmac-mdio code dont really know at this instance of calling
that stmmac_mdio_register was actually successful.

So Adding a check in stmmac_mdio_unregister is always safe.

Without this patch stmmac driver calls stmmac_mdio_register from
stmmac_release which Segfaults as mii bus was never registered at the
first point.

Originally the this bug was found when unloading an stmmac driver
instance which uses mdio-gpio for smi access.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The callback function of call_rcu() just calls a kfree(), so we
can use kfree_rcu() instead of call_rcu() + callback function.

spatch with a semantic match is used to found this problem.
(http://coccinelle.lip6.fr/)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Return -EINVAL rather than 0 given an invalid "mode" parameter.
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The allowed value of "how" is SHUT_RD/SHUT_WR/SHUT_RDWR (0/1/2),
rather than SHUTDOWN_MASK (3).
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Acked-by: Steven Whitehouse <swhiteho@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 9ad7c049 ("tcp: RFC2988bis + taking RTT sample from 3WHS for
the passive open side") changed the initRTO from 3secs to 1sec in
accordance to RFC6298 (former RFC2988bis). This reduced the time till
the last SYN retransmission packet gets sent from 93secs to 31secs.

RFC1122 is stating that the retransmission should be done for at least 3
minutes, but this seems to be quite high.

  "However, the values of R1 and R2 may be different for SYN
  and data segments.  In particular, R2 for a SYN segment MUST
  be set large enough to provide retransmission of the segment
  for at least 3 minutes.  The application can close the
  connection (i.e., give up on the open attempt) sooner, of
  course."

This patch increases the value of TCP_SYN_RETRIES to the value of 6,
providing a retransmission window of 63secs.

The comments for SYN and SYNACK retries have also been updated to
describe the current settings. The same goes for the documentation file
"Documentation/networking/ip-sysctl.txt".
Signed-off-by: Alexander Bergmann <alex@linlab.net>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge the 'net' tree to get the recent set of netfilter bug fixes in
order to assist with some merge hassles Pablo is going to have to deal
with for upcoming changes.
Signed-off-by: David S. Miller <davem@davemloft.net>

Existing code assumes that del_timer returns true for alive conntrack
entries. However, this is not true if reliable events are enabled.
In that case, del_timer may return true for entries that were
just inserted in the dying list. Note that packets / ctnetlink may
hold references to conntrack entries that were just inserted to such
list.

This patch fixes the issue by adding an independent timer for
event delivery. This increases the size of the ecache extension.
Still we can revisit this later and use variable size extensions
to allocate this area on demand.
Tested-by: Oliver Smith <olipro@8.c.9.b.0.7.4.0.1.0.0.2.ip6.arpa>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

This change moves the code for notifying the PF of the VF maximum packet
size into the vf.c file.  The main motivation behind this is that the vf.c
file is supposed to contain all of the messages used when communicating
with the PF.

In addition it creates a separate function for setting the Rx buffer size
so that we have on centralized area to review what buffer sizes will be
requested by the VF.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This change adds PCI suspend and resume support to ixgbevf.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Early Receive has been disabled in the driver so this comment is no longer
applicable.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

CHECK: multiple assignments should be avoided
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Add comments to memory barriers per strict checkpatch.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The POEMB register is 32 bits, not 16.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch correct poll_bnx2x (ndo_poll_controller call) which was not
functioning well with MSI-X.
Signed-off-by: Merav Sicron <meravs@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move netif_napi_add for all queues from the probe call to the open call, to
avoid the case that napi objects are added for queues that may eventually not
be initialized and activated. With the former behavior, the driver could crash
when netpoll was calling ndo_poll_controller.
Signed-off-by: Merav Sicron <meravs@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Following lockdep splat was reported by Pavel Roskin :

[ 1570.586223] ===============================
[ 1570.586225] [ INFO: suspicious RCU usage. ]
[ 1570.586228] 3.6.0-rc3-wl-main #98 Not tainted
[ 1570.586229] -------------------------------
[ 1570.586231] /home/proski/src/linux/net/ipv4/route.c:645 suspicious rcu_dereference_check() usage!
[ 1570.586233]
[ 1570.586233] other info that might help us debug this:
[ 1570.586233]
[ 1570.586236]
[ 1570.586236] rcu_scheduler_active = 1, debug_locks = 0
[ 1570.586238] 2 locks held by Chrome_IOThread/4467:
[ 1570.586240]  #0:  (slock-AF_INET){+.-...}, at: [<ffffffff814f2c0c>] release_sock+0x2c/0xa0
[ 1570.586253]  #1:  (fnhe_lock){+.-...}, at: [<ffffffff815302fc>] update_or_create_fnhe+0x2c/0x270
[ 1570.586260]
[ 1570.586260] stack backtrace:
[ 1570.586263] Pid: 4467, comm: Chrome_IOThread Not tainted 3.6.0-rc3-wl-main #98
[ 1570.586265] Call Trace:
[ 1570.586271]  [<ffffffff810976ed>] lockdep_rcu_suspicious+0xfd/0x130
[ 1570.586275]  [<ffffffff8153042c>] update_or_create_fnhe+0x15c/0x270
[ 1570.586278]  [<ffffffff815305b3>] __ip_rt_update_pmtu+0x73/0xb0
[ 1570.586282]  [<ffffffff81530619>] ip_rt_update_pmtu+0x29/0x90
[ 1570.586285]  [<ffffffff815411dc>] inet_csk_update_pmtu+0x2c/0x80
[ 1570.586290]  [<ffffffff81558d1e>] tcp_v4_mtu_reduced+0x2e/0xc0
[ 1570.586293]  [<ffffffff81553bc4>] tcp_release_cb+0xa4/0xb0
[ 1570.586296]  [<ffffffff814f2c35>] release_sock+0x55/0xa0
[ 1570.586300]  [<ffffffff815442ef>] tcp_sendmsg+0x4af/0xf50
[ 1570.586305]  [<ffffffff8156fc60>] inet_sendmsg+0x120/0x230
[ 1570.586308]  [<ffffffff8156fb40>] ? inet_sk_rebuild_header+0x40/0x40
[ 1570.586312]  [<ffffffff814f4bdd>] ? sock_update_classid+0xbd/0x3b0
[ 1570.586315]  [<ffffffff814f4c50>] ? sock_update_classid+0x130/0x3b0
[ 1570.586320]  [<ffffffff814ec435>] do_sock_write+0xc5/0xe0
[ 1570.586323]  [<ffffffff814ec4a3>] sock_aio_write+0x53/0x80
[ 1570.586328]  [<ffffffff8114bc83>] do_sync_write+0xa3/0xe0
[ 1570.586332]  [<ffffffff8114c5a5>] vfs_write+0x165/0x180
[ 1570.586335]  [<ffffffff8114c805>] sys_write+0x45/0x90
[ 1570.586340]  [<ffffffff815d2722>] system_call_fastpath+0x16/0x1b
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The MDIO controller on the Frame Manager (Fman) is compatible with the
QE and Gianfar MDIO controllers, but we don't care about the TBI because
the Ethernet drivers (FMD) take care of programming it.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Take advantage of the new mdiobus_alloc_size() function to combine three
different memory allocations into one.  This also simplies the error
handling.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make the device tree probe function more data-driven, so that it no longer
searches the 'compatible' property more than once.  The of_device_id[] array
allows for per-entry private data, so we use that to store details about each
type of node that the driver supports.  This removes the need to check the
'compatible' property inside the probe function.

The driver supports four types on MDIO devices:

1) Gianfar MDIO nodes that only map the MII registers
2) Gianfar MDIO nodes that map the full MDIO register set
3) eTSEC2 MDIO nodes (which map the full MDIO register set)
4) QE MDIO nodes (which map only the MII registers)

Gianfar, eTSEC2, and QE have different mappings for the TBIPA register, which
is needed to initialize the TBI PHY.  In addition, the QE needs a special
hack because of the way the device tree is ordered.

All of this information is encapsulated in the fsl_pq_mdio_data structure,
so when an MDIO node is probed, per-device data and functions are used
to determine how to initialize the device.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

1) Replace printk with dev_err

2) Fix some whitespace mistakes

3) Rename "ofdev" to "pdev", since it's a platform_device now

4) Fix an inadvertent compound statement by replacing commas with semicolons
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A few small functions were called only by other functions in the same
file, so merge them together.  One function, for example, was calculating
the device address even though the caller was doing the same thing.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove several unnecessary #include statements.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

None of the functions in fsl_pq_mdio.c are used by any other source file,
so there's no point in exporting them.  Merge the header file into the
source file, make all the functions static, remove any EXPORT_SYMBOL
statements, and delete any #include "fsl_pq_mdio.h" statements.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Free was missing and kcalloc() is better placed in be_ctrl_init()
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

BE3 FW initializes VF tx-rate to 100Mbps. Fix this to 10Gbps.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

BE3 FW allocates VF resources for upto 30 VFs per PF while a max value of 32
may be reported via PCI config space. Fix this in the driver.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Changes from commit df505e were incorrectly over-written by commit 10ef9ab4.
Fixing the same.

Change log of the original fix:
    Currently RSS rings are not created in a multi-channel config.
    RSS rings can be created on one (out of four) interfaces per port in a
    multi-channel config. Doing this insulates the driver from a FW bug wherin
    multi-channel config is wrongly reported even when not enabled. This also
    helps performance in a multi-channel config, as one interface per port gets
    RSS rings.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The IEEE 802.15.4 standard represents a networking protocol. I don't
exactly know why drivers for this protocol are stored into the root
'driver' folder, but better will be to store them with other
networking stuff. Currently there are only 3 drivers available for
IEEE 802.15.4 stack, so lets do it now with the smallest overhead.
Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The code under _init and _exit functions is similar to the code of
module_spi_driver macro, which is a wrapper to the module_driver macro,
so use it instead.
Signed-off-by: Alexander Smirnov <alex.bluesman.smirnov@gmail.com>
Cc: Devendra Naga <develkernel412222@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit c3def943 have added support for
new pci ids of the 57840 board, while failing to change the obsolete value
in 'pci_ids.h'.
This patch does so, allowing the probe of such devices.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>