Setting the vibrator enable_mask is not implemented correctly:

For regmap_update_bits(map, reg, mask, val) we give in either
regs->enable_mask or 0 (= no-op) as mask and "val" as value.
But "val" actually refers to the vibrator voltage control register,
which has nothing to do with the enable_mask.

So we usually end up doing nothing when we really wanted
to enable the vibrator.

We want to set or clear the enable_mask (to enable/disable the vibrator).
Therefore, change the call to always modify the enable_mask
and set the bits only if we want to enable the vibrator.

Fixes: d4c7c5c9 ("Input: pm8xxx-vib - handle separate enable register")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200114183442.45720-1-stephan@gerhold.netSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The driver was issuing synchronous uninterruptible control requests
without using a timeout. This could lead to the driver hanging on probe
due to a malfunctioning (or malicious) device until the device is
physically disconnected. While sleeping in probe the driver prevents
other devices connected to the same hub from being added to (or removed
from) the bus.

The USB upper limit of five seconds per request should be more than
enough.

Fixes: 99f83c9c ("[PATCH] USB: add driver for Keyspan Digital Remote")
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: stable <stable@vger.kernel.org>     # 2.6.13
Link: https://lore.kernel.org/r/20200113171715.30621-1-johan@kernel.orgSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

We need the of_match table if we want to use the compatible string in
the pmic's child node and get the onkey driver loaded automatically.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The F54 Report Data is apparently read through a fifo and for
the smbus protocol that means that between reading a block of 32
bytes the rmiaddr shouldn't be incremented. However, changing
that causes other non-fifo reads to fail and so that change was
reverted.

This patch changes just the F54 function and it now reads 32 bytes
at a time from the fifo, using the F54_FIFO_OFFSET to update the
start address that is used when reading from the fifo.

This has only been tested with smbus, not with i2c or spi. But I
suspect that the same is needed there since I think similar
problems will occur there when reading more than 256 bytes.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Tested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: Timo Kaufmann <timokau@zoho.com>
Link: https://lore.kernel.org/r/20200115124819.3191024-3-hverkuil-cisco@xs4all.nlSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This reverts commit a284e11c.

This causes problems (drifting cursor) with at least the F11 function that
reads more than 32 bytes.

The real issue is in the F54 driver, and so this should be fixed there, and
not in rmi_smbus.c.

So first revert this bad commit, then fix the real problem in F54 in another
patch.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: Timo Kaufmann <timokau@zoho.com>
Fixes: a284e11c ("Input: synaptics-rmi4 - don't increment rmiaddr for SMBus transfers")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200115124819.3191024-2-hverkuil-cisco@xs4all.nlSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Make sure to use the current alternate setting when verifying the
interface descriptors to avoid binding to an invalid interface.

This in turn could cause the driver to misbehave or trigger a WARN() in
usb_submit_urb() that kernels with panic_on_warn set would choke on.

Fixes: bdb5c57f ("Input: add sur40 driver for Samsung SUR40 (aka MS Surface 2.0/Pixelsense)")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Vladis Dronov <vdronov@redhat.com>
Link: https://lore.kernel.org/r/20191210113737.4016-8-johan@kernel.orgSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Drop the second, redundant reinitialisation of the endpoint-descriptor
pointer from probe.
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Vladis Dronov <vdronov@redhat.com>
Link: https://lore.kernel.org/r/20191210113737.4016-7-johan@kernel.orgSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Make sure to use the current altsetting when printing size of any extra
descriptors of the interface.

Also fix the s/endpoint/interface/ mixup in the message itself.
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Vladis Dronov <vdronov@redhat.com>
Link: https://lore.kernel.org/r/20191210113737.4016-6-johan@kernel.orgSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The driver was checking the number of endpoints of the first alternate
setting instead of the current one, something which could lead to the
driver binding to an invalid interface.

This in turn could cause the driver to misbehave or trigger a WARN() in
usb_submit_urb() that kernels with panic_on_warn set would choke on.

Fixes: 162f98de ("Input: gtco - fix crash on detecting device without endpoints")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Vladis Dronov <vdronov@redhat.com>
Link: https://lore.kernel.org/r/20191210113737.4016-5-johan@kernel.orgSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Make sure to always use the descriptors of the current alternate setting
to avoid future issues when accessing fields that may differ between
settings.
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Vladis Dronov <vdronov@redhat.com>
Link: https://lore.kernel.org/r/20191210113737.4016-4-johan@kernel.orgSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The driver was checking the number of endpoints of the first alternate
setting instead of the current one, something which could lead to the
driver binding to an invalid interface.

This in turn could cause the driver to misbehave or trigger a WARN() in
usb_submit_urb() that kernels with panic_on_warn set would choke on.

Fixes: 8e20cf2b ("Input: aiptek - fix crash on detecting device without endpoints")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Vladis Dronov <vdronov@redhat.com>
Link: https://lore.kernel.org/r/20191210113737.4016-3-johan@kernel.orgSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The driver was checking the number of endpoints of the first alternate
setting instead of the current one, something which could be used by a
malicious device (or USB descriptor fuzzer) to trigger a NULL-pointer
dereference.

Fixes: 1afca2b6 ("Input: add Pegasus Notetaker tablet driver")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Martin Kepplinger <martink@posteo.de>
Acked-by: Vladis Dronov <vdronov@redhat.com>
Link: https://lore.kernel.org/r/20191210113737.4016-2-johan@kernel.orgSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The driver misses a check for devm_thermal_zone_of_sensor_register().
Add a check to fix it.

Fixes: e28d0c9c ("input: convert sun4i-ts to use devm_thermal_zone_of_sensor_register")
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

We observed a large(order-3) allocation in evdev_open() and it may
cause an OOM kernel panic in kzalloc(), before we getting to the
vzalloc() fallback.

Fix it by converting kzalloc()/vzalloc() to kvzalloc() to avoid the
OOM killer logic as we have a vmalloc fallback.

InputReader invoked oom-killer: gfp_mask=0x240c2c0
(GFP_KERNEL|__GFP_NOWARN|__GFP_COMP|__GFP_ZERO), nodemask=0, order=3,
oom_score_adj=-900
...
(dump_backtrace) from (show_stack+0x18/0x1c)
(show_stack) from (dump_stack+0x94/0xa8)
(dump_stack) from (dump_header+0x7c/0xe4)
(dump_header) from (out_of_memory+0x334/0x348)
(out_of_memory) from (__alloc_pages_nodemask+0xe9c/0xeb8)
(__alloc_pages_nodemask) from (kmalloc_order_trace+0x34/0x128)
(kmalloc_order_trace) from (__kmalloc+0x258/0x36c)
(__kmalloc) from (evdev_open+0x5c/0x17c)
(evdev_open) from (chrdev_open+0x100/0x204)
(chrdev_open) from (do_dentry_open+0x21c/0x354)
(do_dentry_open) from (vfs_open+0x58/0x84)
(vfs_open) from (path_openat+0x640/0xc98)
(path_openat) from (do_filp_open+0x78/0x11c)
(do_filp_open) from (do_sys_open+0x130/0x244)
(do_sys_open) from (SyS_openat+0x14/0x18)
(SyS_openat) from (__sys_trace_return+0x0/0x10)
...
Normal: 12488*4kB (UMEH) 6984*8kB (UMEH) 2101*16kB (UMEH) 0*32kB
0*64kB 0*128kB 0*256kB 0*512kB 0*1024kB 0*2048kB 0*4096kB = 139440kB
HighMem: 206*4kB (H) 131*8kB (H) 42*16kB (H) 2*32kB (H) 0*64kB
0*128kB 0*256kB 0*512kB 0*1024kB 0*2048kB 0*4096kB = 2608kB
...
Kernel panic - not syncing: Out of memory and no killable processes...
Signed-off-by: Miles Chen <miles.chen@mediatek.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

When reading key state from SCU, the response data from SCU firmware
is 4 bytes due to MU message protocol, but ONLY the first byte is the
key state, other 3 bytes could be some dirty data, so we should ONLY
take the first byte as key state to avoid reporting incorrect state.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Fixes: 688f1dfb ("Input: keyboard - imx_sc: Add i.MX system controller key support")
Link: https://lore.kernel.org/r/1576202909-1661-1-git-send-email-Anson.Huang@nxp.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

If we happen to have a garbage in input device's keycode table with values
too big we'll end up doing clear_bit() with offset way outside of our
bitmaps, damaging other objects within an input device or even outside of
it. Let's add sanity checks to the returned old keycodes.

Reported-by: syzbot+c769968809f9359b07aa@syzkaller.appspotmail.com
Reported-by: syzbot+76f3a30e88d256644c78@syzkaller.appspotmail.com
Link: https://lore.kernel.org/r/20191207212757.GA245964@dtor-wsSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Going through all uses of timeval, I noticed that we screwed up
input_event in the previous attempts to fix it:

The time fields now match between kernel and user space, but all following
fields are in the wrong place.

Add the required padding that is implied by the glibc timeval definition
to fix the layout, and use a struct initializer to avoid leaking kernel
stack data.

Fixes: 141e5dca ("Input: input_event - fix the CONFIG_SPARC64 mixup")
Fixes: 2e746942 ("Input: input_event - provide override for sparc64")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20191213204936.3643476-2-arnd@arndb.de
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

uinput device is always available for writing so we should always report
EPOLLOUT and EPOLLWRNORM bits, not only when there is nothing to read from
the device.

Fixes: d4b675e1 ("Input: uinput - fix returning EPOLLOUT from uinput_poll")
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Link: https://lore.kernel.org/r/20191209202254.GA107567@dtor-wsSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Prepare second round of updates for 5.5 merge window.

This increment of rmi_smbus in rmi_smb_read/write_block() causes
garbage to be read/written.

The first read of SMB_MAX_COUNT bytes is fine, but after that
it is nonsense. Trial-and-error showed that by dropping the
increment of rmiaddr everything is fine and the F54 function
properly works.

I tried a hack with rmi_smb_write_block() as well (writing to the
same F54 touchpad data area, then reading it back), and that
suggests that there too the rmiaddr increment has to be dropped.
It makes sense that if it has to be dropped for read, then it has
to be dropped for write as well.

It looks like the initial work with F54 was done using i2c, not smbus,
and it seems nobody ever tested F54 with smbus. The other functions
all read/write less than SMB_MAX_COUNT as far as I can tell, so this
issue was never noticed with non-F54 functions.

With this change I can read out the touchpad data correctly on my
Lenovo X1 Carbon 6th Gen laptop.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Link: https://lore.kernel.org/r/8dd22e21-4933-8e9c-a696-d281872c8de7@xs4all.nl
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

F34 is a bit special as it reinitializes the device and related driver
structs during the firmware update. This clears the fn_irq_mask which
will then prevent F34 from receiving further interrupts, leading to
timeouts during the firmware update. Make sure to reinitialize the
IRQ enables at the appropriate times.

The issue is in F34 code, but the commit in the fixes tag exposed the
issue, as before this commit things would work by accident.

Fixes: 363c5387 (Input: synaptics-rmi4 - avoid processing unknown IRQs)
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Link: https://lore.kernel.org/r/20191129133514.23224-1-l.stach@pengutronix.de
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The touchscreen on the Teclast X89 is mounted upside down in relation to
the display orientation (the touchscreen itself is mounted upright, but the
display is mounted upside-down). Add a quirk for this so that we send
coordinates which match the display orientation.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/20191202085636.6650-1-hdegoede@redhat.com
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Add keycode for toggling electronic privacy screen to the keycodes
definition. Some new laptops have a privacy screen which can be toggled
with a key on the keyboard.
Signed-off-by: Mathew King <mathewk@chromium.org>
Link: https://lore.kernel.org/r/20191017163208.235518-1-mathewk@chromium.orgSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Always return EPOLLOUT from uinput_poll to allow polling /dev/uinput
for writable state.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Link: https://lore.kernel.org/r/20191204025014.5189-1-marcel@holtmann.orgSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Gratuitous NULL initializers rarely help and often prevent compiler
from warning about using uninitialized variable. Let's remove them.
Reviewed-by: Anson Huang <Anson.Huang@nxp.com>
Link: https://lore.kernel.org/r/20191125211407.GA97812@dtor-wsSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The first generation i.MX6 processors does not send an interrupt when the
power key is pressed. It sends a power down request interrupt if the key is
released before a hard shutdown (5 second press). This should allow
software to bring down the SoC safely.

For this driver to work as a regular power key with the older SoCs, we need
to send a keypress AND release when we get the power down request irq.
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Link: https://lore.kernel.org/r/20191125161210.8275-1-robin@protonic.nlSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Prepare input updates for 5.5 merge window.

The v4l2-compliance utility reported several V4L2 API compliance
issues:

- the sequence counter wasn't filled in
- the sequence counter wasn't reset to 0 at the start of streaming
- the returned field value wasn't set to V4L2_FIELD_NONE
- the timestamp wasn't set
- the payload size was undefined if an error was returned
- min_buffers_needed doesn't need to be initialized

Fix these issues.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de
Link: https://lore.kernel.org/r/20191119105118.54285-3-hverkuil-cisco@xs4all.nlSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Some Lenovo X1 Carbon Gen 6 laptops report LEN0091. Add this
to the smbus_pnp_ids list.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191119105118.54285-2-hverkuil-cisco@xs4all.nlSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
	$ sed -e 's/^        /\t/' -i */Kconfig
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/1574306373-29581-1-git-send-email-krzk@kernel.orgSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This reverts commit 68b9c5066e39af41d3448abfc887c77ce22dd64d.

Ugh, I really dropped the ball on this one :\. So as it turns out RMI4
works perfectly fine on the X1 Extreme Gen 2 except for one thing I
didn't notice because I usually use the trackpoint: clicking with the
touchpad. Somehow this is broken, in fact we don't even seem to indicate
BTN_LEFT as a valid event type for the RMI4 touchpad. And, I don't even
see any RMI4 events coming from the touchpad when I press down on it.
This only seems to work for PS/2 mode.

Since that means we have a regression, and PS/2 mode seems to work fine
for the time being - revert this for now. We'll have to do a more
thorough investigation on this.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://lore.kernel.org/r/20191119234534.10725-1-lyude@redhat.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Just got one of these for debugging some unrelated issues, and noticed
that Lenovo seems to have gone back to using RMI4 over smbus with
Synaptics touchpads on some of their new systems, particularly this one.
So, let's enable RMI mode for the X1 Extreme 2nd Generation.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://lore.kernel.org/r/20191115221814.31903-1-lyude@redhat.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The SCU message's data field used for receiving response data from SCU
should be 32-bit width, as SCU will send back 32-bit width data.

This solves kernel panic when CONFIG_CC_HAVE_STACKPROTECTOR_SYSREG is
enabled.

[    1.950768] Kernel panic - not syncing: stack-protector: Kernel stack is corrupted
[    1.980607] Workqueue: events imx_sc_check_for_events
[    1.985657] Call trace:
[    1.988104]  dump_backtrace+0x0/0x140
[    1.991768]  show_stack+0x14/0x20
[    1.995090]  dump_stack+0xb4/0xf8
[    1.998407]  panic+0x158/0x324
[    2.001463]  print_tainted+0x0/0xa8
[    2.004950]  imx_sc_check_for_events+0x18c/0x190
[    2.009569]  process_one_work+0x198/0x320
[    2.013579]  worker_thread+0x48/0x420
[    2.017252]  kthread+0xf0/0x120
[    2.020394]  ret_from_fork+0x10/0x18
[    2.023977] SMP: stopping secondary CPUs
[    2.027901] Kernel Offset: disabled
[    2.031391] CPU features: 0x0002,2100600c
[    2.035401] Memory Limit: none
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Fixes: 688f1dfb ("Input: keyboard - imx_sc: Add i.MX system controller key support")
Link: https://lore.kernel.org/r/1573730499-2224-1-git-send-email-Anson.Huang@nxp.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The driver forgets to destroy workqueue in remove() similarly to what is
done when probe() fails. Add a call to destroy_workqueue() to fix it.

Since unregistration will wait for the work to finish, we do not need to
cancel/flush the work instance in remove().
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191114023405.31477-1-hslester96@gmail.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

No timer must be left running when the device goes away.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Reported-and-tested-by: syzbot+b6c55daa701fc389e286@syzkaller.appspotmail.com
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/1573726121.17351.3.camel@suse.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The device md->input is used after it is released. Setting the device
data to NULL is unnecessary as the device is never used again. Instead,
md->input should be assigned NULL to avoid accessing the freed memory
accidently. Besides, checking md->si against NULL is superfluous as it
points to a variable address, which cannot be NULL.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Link: https://lore.kernel.org/r/1572936379-6423-1-git-send-email-bianpan2016@163.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The driver for F54 just polls the status and doesn't even have a IRQ
handler registered. Make sure to disable all F54 IRQs, so we don't crash
the kernel on a nonexistent handler.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Link: https://lore.kernel.org/r/20191105114402.6009-1-l.stach@pengutronix.de
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Only show the 'calibrate' sysfs attribute on chip flavours
which support calibration by writing to a calibration register.

Do this by adding a flag to the chip operations structure.
Signed-off-by: Sven Van Asbroeck <TheSven73@gmail.com>
Link: https://lore.kernel.org/r/20191112210148.3535-2-TheSven73@gmail.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Optionally allow the touch screen resolution to be set by adding
it to the chip operations structure. If it is omitted (left zero),
the resolution defaults to 64K. Which is the previously hard-coded
value.

Set the ili2117 resolution to 2048, as indicated in its datasheet.
Signed-off-by: Sven Van Asbroeck <TheSven73@gmail.com>
Link: https://lore.kernel.org/r/20191112210148.3535-1-TheSven73@gmail.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The driver's method to retrieve the firmware version on ili2117/
ili2118 chip flavours is incorrect. The firmware version register
address and layout are wrong.

The firmware version is not actually used anywhere inside or
outside this driver. There is a dev_dbg() print, but that is
only visible when the developer explicitly compiles in debug
support.

Don't make the code more complicated to preserve a feature that
no-one is using. Remove all code associated with chip firmware
version.
Signed-off-by: Sven Van Asbroeck <TheSven73@gmail.com>
Link: https://lore.kernel.org/r/20191112164429.11225-1-TheSven73@gmail.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>