Pull i2c changes from Wolfram Sang:

 - an arbitration driver.  While the driver is quite simple, it caused
   discussion if we need additional arbitration on top of the one
   specified in the I2C standard.  Conclusion is that I accept a few
   generic mechanisms, but not very specific ones.

 - the core lost the detach_adapter() call.  It has no users anymore and
   was in the way for other cleanups.  attach_adapter() is sadly still
   there since there are users waiting to be converted.

 - the core gained a bus recovery infrastructure.  I2C defines a way to
   recover if the data line is stalled.  This mechanism is now in the
   core and drivers can now pass some data to make use of it.

 - bigger driver cleanups for designware, s3c2410

 - removing superfluous refcounting from drivers

 - removing Ben Dooks as second maintainer due to inactivity.  Thanks
   for all your work so far, Ben!

 - bugfixes, feature additions, devicetree fixups, simplifications...

* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (38 commits)
  i2c: xiic: must always write 16-bit words to TX_FIFO
  i2c: octeon: use HZ in timeout value
  i2c: octeon: Fix i2c fail problem when a process is terminated by a signal
  i2c: designware-pci: drop superfluous {get|put}_device
  i2c: designware-plat: drop superfluous {get|put}_device
  i2c: davinci: drop superfluous {get|put}_device
  MAINTAINERS: Ben Dooks is inactive regarding I2C
  i2c: mux: Add i2c-arb-gpio-challenge 'mux' driver
  i2c: at91: convert to dma_request_slave_channel_compat()
  i2c: mxs: do error checking and handling in PIO mode
  i2c: mxs: remove races in PIO code
  i2c-designware: switch to use runtime PM autosuspend
  i2c-designware: use usleep_range() in the busy-loop
  i2c-designware: enable/disable the controller properly
  i2c-designware: use dynamic adapter numbering on Lynxpoint
  i2c-designware-pci: use managed functions pcim_* and devm_*
  i2c-designware-pci: use dev_err() instead of printk()
  i2c-designware: move to managed functions (devm_*)
  i2c: remove CONFIG_HOTPLUG ifdefs
  i2c: s3c2410: Add SMBus emulation for block read
  ...

Pull virtio & lguest updates from Rusty Russell:
 "Lots of virtio work which wasn't quite ready for last merge window.

  Plus I dived into lguest again, reworking the pagetable code so we can
  move the switcher page: our fixmaps sometimes take more than 2MB now..."

Ugh.  Annoying conflicts with the tcm_vhost -> vhost_scsi rename.
Hopefully correctly resolved.

* tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux: (57 commits)
  caif_virtio: Remove bouncing email addresses
  lguest: improve code readability in lg_cpu_start.
  virtio-net: fill only rx queues which are being used
  lguest: map Switcher below fixmap.
  lguest: cache last cpu we ran on.
  lguest: map Switcher text whenever we allocate a new pagetable.
  lguest: don't share Switcher PTE pages between guests.
  lguest: expost switcher_pages array (as lg_switcher_pages).
  lguest: extract shadow PTE walking / allocating.
  lguest: make check_gpte et. al return bool.
  lguest: assume Switcher text is a single page.
  lguest: rename switcher_page to switcher_pages.
  lguest: remove RESERVE_MEM constant.
  lguest: check vaddr not pgd for Switcher protection.
  lguest: prepare to make SWITCHER_ADDR a variable.
  virtio: console: replace EMFILE with EBUSY for already-open port
  virtio-scsi: reset virtqueue affinity when doing cpu hotplug
  virtio-scsi: introduce multiqueue support
  virtio-scsi: push vq lock/unlock into virtscsi_vq_done
  virtio-scsi: pass struct virtio_scsi to virtqueue completion function
  ...

Pull vfio updates from Alex Williamson:
 "Changes include extension to support PCI AER notification to
  userspace, byte granularity of PCI config space and access to
  unarchitected PCI config space, better protection around IOMMU driver
  accesses, default file mode fix, and a few misc cleanups."

* tag 'vfio-for-v3.10' of git://github.com/awilliam/linux-vfio:
  vfio: Set container device mode
  vfio: Use down_reads to protect iommu disconnects
  vfio: Convert container->group_lock to rwsem
  PCI/VFIO: use pcie_flags_reg instead of access PCI-E Capabilities Register
  vfio-pci: Enable raw access to unassigned config space
  vfio-pci: Use byte granularity in config map
  vfio: make local function vfio_pci_intx_unmask_handler() static
  VFIO-AER: Vfio-pci driver changes for supporting AER
  VFIO: Wrapper for getting reference to vfio_device

Pull vhost cleanups and fixes from Michael Tsirkin:
 "Here are vhost cleanups and fixes by Asias He and myself.  They affect
  both vhost-net and vhost-scsi devices.  They also *depend* on both
  net-next and target-pending, where the net and target commits these
  changes depend on are already merged.  So merging through the common
  vhost tree."

* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
  vhost_scsi: module rename
  tcm_vhost: header split up
  vhost: src file renames
  vhost: fix error handling in RESET_OWNER ioctl
  tcm_vhost: remove virtio-net.h dependency
  vhost: move per-vq net specific fields out to net
  tcm_vhost: document inflight ref-counting use
  vhost: move vhost-net zerocopy fields to net.c
  tcm_vhost: Wait for pending requests in vhost_scsi_flush()
  vhost: Allow device specific fields per vq

Pull powerpc update from Benjamin Herrenschmidt:
 "The main highlights this time around are:

   - A pile of addition POWER8 bits and nits, such as updated
     performance counter support (Michael Ellerman), new branch history
     buffer support (Anshuman Khandual), base support for the new PCI
     host bridge when not using the hypervisor (Gavin Shan) and other
     random related bits and fixes from various contributors.

   - Some rework of our page table format by Aneesh Kumar which fixes a
     thing or two and paves the way for THP support.  THP itself will
     not make it this time around however.

   - More Freescale updates, including Altivec support on the new e6500
     cores, new PCI controller support, and a pile of new boards support
     and updates.

   - The usual batch of trivial cleanups & fixes"

* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (156 commits)
  powerpc: Fix build error for book3e
  powerpc: Context switch the new EBB SPRs
  powerpc: Turn on the EBB H/FSCR bits
  powerpc: Replace CPU_FTR_BCTAR with CPU_FTR_ARCH_207S
  powerpc: Setup BHRB instructions facility in HFSCR for POWER8
  powerpc: Fix interrupt range check on debug exception
  powerpc: Update tlbie/tlbiel as per ISA doc
  powerpc: Print page size info during boot
  powerpc: print both base and actual page size on hash failure
  powerpc: Fix hpte_decode to use the correct decoding for page sizes
  powerpc: Decode the pte-lp-encoding bits correctly.
  powerpc: Use encode avpn where we need only avpn values
  powerpc: Reduce PTE table memory wastage
  powerpc: Move the pte free routines from common header
  powerpc: Reduce the PTE_INDEX_SIZE
  powerpc: Switch 16GB and 16MB explicit hugepages to a different page table format
  powerpc: New hugepage directory format
  powerpc: Don't truncate pgd_index wrongly
  powerpc: Don't hard code the size of pte page
  powerpc: Save DAR and DSISR in pt_regs on MCE
  ...

Pull ARM SoC multiplatform updates from Olof Johansson:
 "More multiplatform enablement for ARM platforms.  The ones converted
  in this branch are:

   - bcm2835
   - cns3xxx
   - sirf
   - nomadik
   - msx
   - spear
   - tegra
   - ux500

  We're getting close to having most of them converted!

  One of the larger platforms remaining is Samsung Exynos, and there are
  a bunch of supporting patches in this merge window for it.  There was
  a patch in this branch to a early version of multiplatform conversion,
  but it ended up being reverted due to need of more bake time.  The
  revert commit is part of the branch since it would have required
  rebasing multiple dependent branches and they were stable by then"

* tag 'multiplatform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (70 commits)
  mmc: sdhci-s3c: Fix operation on non-single image Samsung platforms
  clocksource: nomadik-mtu: fix up clocksource/timer
  Revert "ARM: exynos: enable multiplatform support"
  ARM: SPEAr13xx: Fix typo "ARCH_HAVE_CPUFREQ"
  ARM: exynos: enable multiplatform support
  rtc: s3c: make header file local
  mtd: onenand/samsung: make regs-onenand.h file local
  thermal/exynos: remove unnecessary header inclusions
  mmc: sdhci-s3c: remove platform dependencies
  ARM: samsung: move mfc device definition to s5p-dev-mfc.c
  ARM: exynos: move debug-macro.S to include/debug/
  ARM: exynos: prepare for sparse IRQ
  ARM: exynos: introduce EXYNOS_ATAGS symbol
  ARM: tegra: build assembly files with -march=armv7-a
  ARM: Push selects for TWD/SCU into machine entries
  ARM: ux500: build hotplug.o for ARMv7-a
  ARM: ux500: move to multiplatform
  ARM: ux500: make remaining headers local
  ARM: ux500: make irqs.h local to platform
  ARM: ux500: get rid of <mach/[hardware|db8500-regs].h>
  ...

Pull ARM SoC platform updates from Olof Johansson:
 "This branch contains part 1 of the platform updates for 3.10.  Among
  the highlights:

   - Support for the new Atmel Cortex-A5 based platforms (SAMA5D3)
   - New support for CSR SiRFatlas6 SoCs
   - A handful of updates for NVidia T114 (a.k.a. Tegra 4)
   - A bunch of updates for the shmobile platforms
   - A handful of updates for davinci
   - A few updates for Qualcomm MSM
   - Plus a handful of other patches, defconfig updates, etc."

* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (135 commits)
  ARM: tegra: pm: fix build error w/o PM_SLEEP
  ARM: davinci: ensure global variables are declared
  ARM: davinci: sram.c: fix incorrect type in assignment
  ARM: davinci: da8xx dt: make file local symbols static
  ARM: davinci: da8xx: add remoteproc support
  ARM: socfpga: Upgrade clk driver for socfpga to make use of dts clock entries
  ARM: socfpga: Add clock entries into device tree
  ARM: socfpga: Enable soft reset
  ARM: EXYNOS: replace cpumask by the corresponding macro
  ARM: EXYNOS: handle properly the return values
  ARM: EXYNOS: factor out the idle states
  ARM: OMAP4: Enable fix for Cortex-A9 erratas
  ARM: OMAP2+: Export SoC information to userspace
  ARM: OMAP2+: SoC name and revision unification
  ARM: OMAP2+: Move common part of late init into common function
  ARM: tegra: pm: remove duplicated include from pm.c
  ARM: davinci: da850: override mmc DT node device name
  ARM: davinci: da850: add mmc DT entries
  mmc: davinci_mmc: add DT support
  ARM: SAMSUNG: check processor type before cache restoration in resume
  ...

Pull ARM SoC device-tree updates from Olof Johansson:
 "Part 1 of device-tree updates for 3.10.  The bulk of the churn in this
  branch is due to i.MX moving from C-defined pin control over to device
  tree, which is a one-time conversion that will allow greater
  flexibility down the road.

  Besides that, there's PCI-e bindings for Marvell mvebu platforms and a
  handful of cleanups to tegra due to the new include file functionality
  of the device tree compiler"

* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (113 commits)
  arm: mvebu: PCIe Device Tree informations for Armada XP GP
  arm: mvebu: PCIe Device Tree informations for Armada 370 DB
  arm: mvebu: PCIe Device Tree informations for Armada 370 Mirabox
  arm: mvebu: PCIe Device Tree informations for Armada XP DB
  arm: mvebu: PCIe Device Tree informations for OpenBlocks AX3-4
  arm: mvebu: add PCIe Device Tree informations for Armada XP
  arm: mvebu: add PCIe Device Tree informations for Armada 370
  ARM: sunxi: unify osc24M_fixed and osc24M
  arm: vt8500: Add SDHC support to WM8505 DT
  ARM: dts: Add a 64 bits version of the skeleton device tree
  ARM: mvebu: Add Device Bus and CFI flash memory support to defconfig
  ARM: mvebu: Add support for NOR flash device on Openblocks AX3 board
  ARM: mvebu: Add support for NOR flash device on Armada XP-GP board
  ARM: mvebu: Add Device Bus support for Armada 370/XP SoC
  ARM: dts: imx6dl-wandboard: Add USB Host support
  ARM: dts: imx51 cpu node
  ARM: dts: Add missing imx27-phytec-phycore dtb target
  ARM: dts: Add NFC support for i.MX27 Phytec PCM038 module
  ARM: i.MX51: Add PATA support
  ARM: dts: Add initial support for Wandboard Dual-Lite
  ...

Pull ARM SoC cleanup from Olof Johansson:
 "Here is a collection of cleanup patches.  Among the pieces that stand
  out are:

   - The deletion of h720x platforms
   - Split of at91 non-dt platforms to their own Kconfig file to keep
     them separate
   - General cleanups and refactoring of i.MX and MXS platforms
   - Some restructuring of clock tables for OMAP
   - Convertion of PMC driver for Tegra to dt-only
   - Some renames of sunxi -> sun4i (Allwinner A10)
   - ... plus a bunch of other stuff that I haven't mentioned"

* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (119 commits)
  ARM: i.MX: remove unused ARCH_* configs
  ARM i.MX53: remove platform ahci support
  ARM: sunxi: Rework the restart code
  irqchip: sunxi: Rename sunxi to sun4i
  irqchip: sunxi: Make use of the IRQCHIP_DECLARE macro
  clocksource: sunxi: Rename sunxi to sun4i
  clocksource: sunxi: make use of CLKSRC_OF
  clocksource: sunxi: Cleanup the timer code
  ARM: at91: remove trailing semicolon from macros
  ARM: at91/setup: fix trivial typos
  ARM: EXYNOS: remove "config EXYNOS_DEV_DRM"
  ARM: EXYNOS: change the name of USB ohci header
  ARM: SAMSUNG: Remove unnecessary code for dma
  ARM: S3C24XX: Remove unused GPIO drive strength register definitions
  ARM: OMAP4+: PM: Restore CPU power state to ON with clockdomain force wakeup method
  ARM: S3C24XX: Removed unneeded dependency on CPU_S3C2412
  ARM: S3C24XX: Removed unneeded dependency on CPU_S3C2410
  ARM: S3C24XX: Removed unneeded dependency on ARCH_S3C24XX for boards
  ARM: SAMSUNG: Fix typo "CONFIG_SAMSUNG_DEV_RTC"
  ARM: S5P64X0: Fix typo "CONFIG_S5P64X0_SETUP_SDHCI"
  ...

Pull ARM SoC non-critical fixes from Olof Johansson:
 "Here is a collection of fixes (and some intermixed cleanups) that were
  considered less important and thus not included in the later parts of
  the 3.9-rc cycle.

  It's a bit all over the map, contents wise.  A series of ux500 fixes
  and cleanups, a bunch of various fixes for OMAP and tegra, and some
  for Freescale i.MX and even Qualcomm MSM.

  Note that there's also a patch on this branch to globally turn off
  -Wmaybe-uninitialized when building with -Os.  It's been posted
  several times by Arnd and no dissent was raised, but nobody seemed
  interested to pick it up.  So here it is, as the topmost patch."

* tag 'fixes-nc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (70 commits)
  Turn off -Wmaybe-uninitialized when building with -Os
  ARM: orion5x: include linux/cpu.h
  ARM: tegra: call cpu_do_idle from C code
  ARM: u300: fix ages old copy/paste bug
  ARM: OMAP2+: add dependencies on ARCH_MULTI_V6/V7
  ARM: tegra: solve adr range issue with THUMB2_KERNEL enabled
  ARM: tegra: fix relocation truncated error when THUMB2_KERNEL enabled
  ARM: tegra: fix build error when THUMB2_KERNEL enabled
  ARM: msm: Fix uncompess.h tx underrun check
  ARM: vexpress: Remove A9 PMU compatible values for non-A9 platforms
  ARM: cpuimx27 and mbimx27: prepend CONFIG_ to Kconfig macro
  ARM: OMAP2+: fix typo "CONFIG_BRIDGE_DVFS"
  ARM: OMAP1: remove "config MACH_OMAP_HTCWIZARD"
  ARM: mach-imx: mach-imx6q: Fix sparse warnings
  ARM: mach-imx: src: Include "common.h
  ARM: mach-imx: gpc: Include "common.h"
  ARM: mach-imx: avic: Staticize *avic_base
  ARM: mach-imx: tzic: Staticize *tzic_base
  ARM: mach-imx: clk: Include "clk.h"
  ARM: mach-imx: clk-busy: Staticize clk_busy_mux_ops
  ...

Commit 32fcfd40 ("make vfree() safe to call from interrupt
contexts") made it safe to do vfree directly from the RCU callback,
which allows us to simplify ipc/util.c a lot by getting rid of the
differences between vmalloc/kmalloc memory.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Commit 8ad227ff ("net: vlan: add 802.1ad support") added some new
NETIF_F_* features bits, but it added them in the middle of existing
values.

Userland depends upon the flag bits via the per-netdevice 'flags' sysfs
file.

So restore the previous ordering by adding the new flags at the end.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Rename module and update Kconfig and Makefile.
Add alias for compatibility with old userspace
scripts if any.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Asias He <asias@redhat.com>
Acked-by: Nicholas Bellinger <nab@linux-iscsi.org>

move uapi parts to vhost.h
move .c private parts to .c itself
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Asias He <asias@redhat.com>
Acked-by: Nicholas Bellinger <nab@linux-iscsi.org>

Move tcm_vhost.c -> scsi.c
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Asias He <asias@redhat.com>
Acked-by: Nicholas Bellinger <nab@linux-iscsi.org>

Pull VFS updates from Al Viro,

Misc cleanups all over the place, mainly wrt /proc interfaces (switch
create_proc_entry to proc_create(), get rid of the deprecated
create_proc_read_entry() in favor of using proc_create_data() and
seq_file etc).

7kloc removed.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (204 commits)
  don't bother with deferred freeing of fdtables
  proc: Move non-public stuff from linux/proc_fs.h to fs/proc/internal.h
  proc: Make the PROC_I() and PDE() macros internal to procfs
  proc: Supply a function to remove a proc entry by PDE
  take cgroup_open() and cpuset_open() to fs/proc/base.c
  ppc: Clean up scanlog
  ppc: Clean up rtas_flash driver somewhat
  hostap: proc: Use remove_proc_subtree()
  drm: proc: Use remove_proc_subtree()
  drm: proc: Use minor->index to label things, not PDE->name
  drm: Constify drm_proc_list[]
  zoran: Don't print proc_dir_entry data in debug
  reiserfs: Don't access the proc_dir_entry in r_open(), r_start() r_show()
  proc: Supply an accessor for getting the data from a PDE's parent
  airo: Use remove_proc_subtree()
  rtl8192u: Don't need to save device proc dir PDE
  rtl8187se: Use a dir under /proc/net/r8180/
  proc: Add proc_mkdir_data()
  proc: Move some bits from linux/proc_fs.h to linux/{of.h,signal.h,tty.h}
  proc: Move PDE_NET() to fs/proc/proc_net.c
  ...

We moved the definition of shift_to_mmu_psize and mmu_psize_to_shift
out of hugetlbpage.c in patch "powerpc: New hugepage directory format".

These functions are not related to hugetlbpage and we want to use them
outside hugetlbpage.c We missed a definition for book3e when we moved
these functions. Add similar functions to mmu-book3e.h
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

This context switches the new Event Based Branching (EBB) SPRs.  The three new
SPRs are:
  - Event Based Branch Handler Register (EBBHR)
  - Event Based Branch Return Register (EBBRR)
  - Branch Event Status and Control Register (BESCR)
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Matt Evans <matt@ozlabs.org>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

This turns Event Based Branching (EBB) on in the Hypervisor Facility Status and
Control Register (HFSCR) and Facility Status and Control Register (FSCR).
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

We are getting low on cpu feature bits. So rather than add a separate bit for
every new Power8 feature, add a bit for arch 2.07 server catagory and use that
instead.

Hijack the value we had for BCTAR, but swap the value with CFAR so that all the
ARCH defines are together.

Note we don't touch CPU_FTR_TM, because it is conditionally enabled if
the kernel is built with TM support.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Make BHRB instructions available in problem and privileged states.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

We do not want to take single step and branch-taken debug exception
in kernel exception code. But the address range check was not covering
all kernel exception handlers address range.

With this patch we defined the interrupt_end label which defines the
end on kernel exception code. So now we check interrupt_base to
interrupt_end range for not handling debug exception in kernel
exception entry.
Signed-off-by: Bharat Bhushan <bharat.bhushan@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Pull x86/efi changes from Peter Anvin:
 "The bulk of these changes are cleaning up the efivars handling and
  breaking it up into a tree of files.  There are a number of fixes as
  well.

  The entire changeset is pretty big, but most of it is code movement.

  Several of these commits are quite new; the history got very messed up
  due to a mismerge with the urgent changes for rc8 which completely
  broke IA64, and so Ingo requested that we rebase it to straighten it
  out."

* 'x86-efi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  efi: remove "kfree(NULL)"
  efi: locking fix in efivar_entry_set_safe()
  efi, pstore: Read data from variable store before memcpy()
  efi, pstore: Remove entry from list when erasing
  efi, pstore: Initialise 'entry' before iterating
  efi: split efisubsystem from efivars
  efivarfs: Move to fs/efivarfs
  efivars: Move pstore code into the new EFI directory
  efivars: efivar_entry API
  efivars: Keep a private global pointer to efivars
  efi: move utf16 string functions to efi.h
  x86, efi: Make efi_memblock_x86_reserve_range more readable
  efivarfs: convert to use simple_open()

Al's commit e1b5bb6d ("consolidate cond_syscall and SYSCALL_ALIAS
declarations") broke the build on blackfin and metag due to the
following code:

  #ifndef SYMBOL_NAME
  #ifdef CONFIG_SYMBOL_PREFIX
  #define SYMBOL_NAME(x) CONFIG_SYMBOL_PREFIX ## x
  #else
  #define SYMBOL_NAME(x) x
  #endif
  #endif
  #define __SYMBOL_NAME(x) __stringify(SYMBOL_NAME(x))

__stringify literally stringifies CONFIG_SYMBOL_PREFIX ##x, so you get
lines like this in kernel/sys_ni.s:

  .weak CONFIG_SYMBOL_PREFIXsys_quotactl
  .set CONFIG_SYMBOL_PREFIXsys_quotactl,CONFIG_SYMBOL_PREFIXsys_ni_syscall

The patches in Rusty's modules-next tree such as "CONFIG_SYMBOL_PREFIX:
cleanup." cleans up the whole mess around symbol prefixes, so this patch
just attempts to fix the build in the meantime.

The intermediate definition of SYMBOL_NAME above isn't used and is
incorrect when CONFIG_SYMBOL_PREFIX is defined as CONFIG_SYMBOL_PREFIX
is a quoted string literal, so define __SYMBOL_NAME directly depending
on CONFIG_SYMBOL_PREFIX.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Mea-culpa-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: uclinux-dist-devel@blackfin.uclinux.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Move non-public declarations and definitions from linux/proc_fs.h to
fs/proc/internal.h.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Make the PROC_I() and PDE() macros internal to procfs.  This means making
PDE_DATA() out of line.  This could be made more optimal by storing
PDE()->data into inode->i_private.

Also provide a __PDE_DATA() that is inline and internal to procfs.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Supply a function (proc_remove()) to remove a proc entry (and any subtree
rooted there) by proc_dir_entry pointer rather than by name and (optionally)
root dir entry pointer.  This allows us to eliminate all remaining pde->name
accesses outside of procfs.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Grant Likely <grant.likely@linaro.or>
cc: linux-acpi@vger.kernel.org
cc: openipmi-developer@lists.sourceforge.net
cc: devicetree-discuss@lists.ozlabs.org
cc: linux-pci@vger.kernel.org
cc: netdev@vger.kernel.org
cc: netfilter-devel@vger.kernel.org
cc: alsa-devel@alsa-project.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Clean up the pseries scanlog driver's use of procfs:

 (1) Don't need to save the proc_dir_entry pointer as we have the filename to
     remove with.

 (2) Save the scan log buffer pointer in a static variable (there is only one
     of it) and don't save it in the PDE (which doesn't have a destructor).
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
cc: Paul Mackerras <paulus@samba.org>
cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Clean up some of the problems with the rtas_flash driver:

 (1) It shouldn't fiddle with the internals of the procfs filesystem (altering
     pde->count).

 (2) If pid namespaces are in effect, then you can get multiple inodes
     connected to a single pde, thereby rendering the pde->count > 2 test
     useless.

 (3) The pde->count fudging doesn't work for forked, dup'd or cloned file
     descriptors, so add static mutexes and use them to wrap access to the
     driver through read, write and release methods.

 (4) The driver can only handle one device, so allocate most of the data
     previously attached to the pde->data as static variables instead (though
     allocate the validation data buffer with kmalloc).

 (5) We don't need to save the pde pointers as long as we have the filenames
     available for removal.

 (6) Don't try to multiplex what the update file read method does based on the
     filename.  Instead provide separate file ops and split the function.

Whilst we're at it, tabulate the procfile information and loop through it when
creating or destroying them rather than manually coding each one.

[Folded fixes from Vasant Hegde <hegdevasant@linux.vnet.ibm.com>]
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
cc: Paul Mackerras <paulus@samba.org>
cc: Anton Blanchard <anton@samba.org>
cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Use remove_proc_subtree() rather than remove_proc_entry() to remove a
device-specific proc directory and all its children.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Jouni Malinen <j@w1.fi>
cc: Johannes Berg <johannes@sipsolutions.net>
cc: linux-wireless@vger.kernel.org
cc: devel@driverdev.osuosl.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Use remove_proc_subtree() rather than remove_proc_entry() to remove a
minor-specific drm proc directory and all its children.

Things could theoretically be improved by storing the drm_minor pointer in the
minor-specific dir proc_dir_entry struct data and then scrapping the list of
proc files - but that's shared with the debugfs interface where you can't do
that, so I don't see an easy way of doing it.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: dri-devel@lists.freedesktop.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Use minor->index to label things, not the name field from the proc_dir_entry
of the /proc/dwm/<minor>/ directory.

Also, use "%u" not "%d" to render the value and use a 12-byte buffer in which
to render the integer, not a 16-byte buffer.  The longest string an unsigned
int can give you is 10 chars (4294967295) plus a NUL, so round up to 12 as the
stack is likely to be 4- or 8-byte aligned.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: dri-devel@lists.freedesktop.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Constify drm_proc_list[] and related pointers.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: dri-devel@lists.freedesktop.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Don't print proc_dir_entry data in debug as we're soon to have no direct
access to the contents of the PDE.  Print what was put in there instead.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: mjpeg-users@lists.sourceforge.net
cc: linux-media@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Don't access the proc_dir_entry in ReiserFS's r_open(), r_start() r_show()
procfs interface functions.

ReiserFS stores the ->show() method pointer in PDE->data and the super_block
pointer in PDE->parent->data.  This isn't changing.

Currently, ReiserFS passes the PDE pointer into seq_file::private from
r_open() so that r_start() and r_show() can then access it.  Instead, use
seq_open_private() to allocate a two-pointer struct that's passed through
seq_file::private and put the ->show() method and the sb pointers in there.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: reiserfs-devel@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Supply an accessor function for getting the private data from the parent
proc_dir_entry struct of the proc_dir_entry struct associated with an inode.

ReiserFS, for instance, stores the super_block pointer in the proc directory
it makes for that super_block, and a pointer to the respective seq_file show
function in each of the proc files in that directory.

This allows a reduction in the number of file_operations structs, open
functions and seq_operations structs required.  The problem otherwise is that
each show function requires two pieces of data but only has storage for one
per PDE (and this has no release function).
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cc: Jerry Chuang <jerry-chuang@realtek.com>
cc: Maxim Mikityanskiy <maxtram95@gmail.com>
cc: YAMANE Toshiaki <yamanetoshi@gmail.com>
cc: linux-wireless@vger.kernel.org
cc: linux-scsi@vger.kernel.org
cc: devel@driverdev.osuosl.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Use remove_proc_subtree() to remove the airo device subdir and all its
children instead of doing it manually.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: linux-wireless@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>