Signed-off-by: Takashi Iwai <tiwai@suse.de>

Instead of checking the codec SSID in find_mute_led_cfg() for HP Mini
110, set the proper spec->default_polairty in the fixup table.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The PCI vendor ID check in find_mute_led_cfg() is now superfluous
because the function is called in the fixup table entries of HP
machines.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Finally all codecs in patch_sigmatel.c have been converted to use the
standard fixup helpers.  This change also includes trivial cleanups
like the call of common setup for GPIO LED or the removal of unused
function.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

This one is rather a simple conversion.  The fixups for Dell machines
are implemented by fixup functions in the end.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

This time, the only intrusive changes are for HP machines.
As the mute LED fixup and the bass speaker switch are required only
for HP machines, we can move these checks into the fixup entries; the
former is applied generically to all HP machines while the latter for
only certain models.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

This conversion is a bit tricky.  Since STAC927x may take two
different volume-knob initialization values depending on the model, a
new flag, spec->volknob_init, is introduced to indicate whether it's
the standard volume-knob initialization or not.

Also, Dell BIOS model is now directly mapped onto the fixup table
instead of parsing in the function.  This resulted in a new model ref,
STAC_927X_DELL_BIOS_SPDIF, which is a chained entry.

Also, for reducing the fixups, virtual entries like
STAC_927X_DELL_DMIC and STAC_D965_VERBS are introduced.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Rather straightforward conversion, except for ones for Intel Mac.
As Intel Mac have only unique codec SSIDs, we need to remap the fixup
again for the codec SSID and call the new fixup there.

Also, we can reduce model enums like STAC_MACMINI, which are model
aliases for backward compatibility, since they can be pointed directly
via hda_model_fixup table.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Signed-off-by: Takashi Iwai <tiwai@suse.de>

Now for STAC9872.  It has a small fixup table, fortunately.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Similar like the previous commit, convert patch_stac925x() to use the
standard fixup table.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Convert patch_stac9200() to use the standard fixup table instead of
manual switch-case with board_config.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

* test/hda-gen-parser:
  ALSA: hda - Add capture_switch_hook to generic parser

Add a hook for the capture mixer switch.  This will be used by IDT
codecs for controlling the mic-mute LED.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Yet another step forward.  As all features for VIA codecs have been
implemented in the generic driver, we can move on to migrate the VIA
codec parser, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

This patch adds the support for the generic auto-parser to AD codec
driver.  For AD1988, the old code is replaced simply with the new
generic parser.  For other codecs, new model "auto" is added and
directed to use the generic parser.

No fixup codes have been implemented yet as of now.  Eventually we'd
replace each static quirk with the generic parser + fixup.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Just shuffle the codes and add ifdefs for testing to drop the static
quirk codes from patch_conexant.c.

By commenting out ENABLE_CXT_STATIC_QUIRKS define at the beginning of
the file, you can disable the whole static codes.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

... and drop most of own parser code.

It doesn't replace any present static quirks, though.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

This time, the target is Cirrus codec.  Its parser is a subset of
generic parser, so we can migrate fully with it now.

The only tricky part is the handling of SPDIF automute.
Cirrus driver sets the SPDIF out plug over the headphone.  As a
workaround, set spec->gen.master_mute for toggling the headphone (and
other) mute.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

CA0110 codec is a fairly straightforward hardware implementation,
and we can use the generic parser almost as is.
Just set spec->multi_cap_vol flag to follow the current behavior.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Replace the old parser code for C-Media auto-parser with the latest
generic parser.  For compatibility reason, the static bindings are
still left, but they could be cleaned up in future.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Signed-off-by: Takashi Iwai <tiwai@suse.de>

Through the hints via sysfs or patch, user can set specific behavior
flags for the generic parser now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

It'll be used in hda_generic.c, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

The pincfgs, init_verbs and hints set by sysfs or patch might be
changed dynamically on the fly, thus we need to protect it.
Add a simple protection via a mutex.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

As David Henningsson recently suggested, some HP laptops use an unused
mic pin for controlling a mute LED, and this information is provided
via DMI string "HP_Mute_LED_X_Y" string.  This patch adds the generic
support for such cases, as we've already done in patch_sigmatel.c.
This is applied generically to all devices with ID 0x103c.

But as we don't know whether the device 103c:1586 really contains
HP_Mute_LED_X_Y DMI string, still keep the static setup for this
device using the mic2 pin 0x19.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Some fixups such as setting the flags influencing on the parser
behavior should be applied before actually parsing the tree.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Try to recover from the regression: set the HP amp for the speaker and
add the hp jack mode enum as default.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Add the enum controls for changing the headphone amp bits of output
jacks, such as "Headphone Jack Mode".  This feature isn't enabled as
default, so far, unless spec->add_out_jack_modes flag is set.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

When a multi-io jack is switched to another direction, call the
automute and autoswitch update functions, as this jack won't be used
as the headphone or the mic jack that may turn off others.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Add a new fixup type, HDA_FIXUP_PINCTLS, for overriding the pinctl
values of the given pins.  It takes the same array of struct pintbl
like HDA_FIXUP_PINS, but each entry contains the pinctl value instead
of the pin default config value.

This patch also replaces the corresponding codes in patch_realtek.c.
Without this change, the direct call of verbs may be overridden again
by the later call of pinctl restoration by the driver.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

... instead of reading the value from the codec at each time.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Now the whole codebase has been changed from the earlier kernels, it
makes little sense to keep these aliases.  Simply replace with the
official names.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

When a jack is retasked as a different direction (e.g. a mic jack is
used as a CLFE output), such a jack shouldn't be counted as the target
for the automatic jack switching.  Skip the automute or the autoswitch
when the current pinctl direction is different from what we suppose.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Use the new pin target accessors for managing the current pinctl
values in the generic parser.  The pinctl values of all active pins
are once determined at the initialization phase, and stored via
snd_hda_codec_set_pin_target().  This will be referred again in the
codec init or resume phase to set the actual pinctl.

This value is kept while the auto-mute.  When a line-out or a speaker
pin is muted by auto-mute, the driver simply disables the pin, but it
doesn't touch the cached pinctl target value.  Upon unmute, this value
is used to restore the original pinctl in return.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Check more strictly about the validity of pinctl values in
snd_hda_set_pin_ctl() and correct the wrong bits automatically.
Also provide the helper function to correct pinctl bits to codec
drivers.

This automatically fixes the invalid pinctl writes that are found in
a few Realtek fixups for NID 0x0f amp like ASUS A6Rp.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

We already have the list of whole pin widgets and there is an unused
space in the list; let's use it for caching the current pinctl value.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

When a DAC is reassigned from surrounds to front or ADCs are reduced
due to incomplete imux, we clear the path indices but the path
instances remain as is.  Since the paths might be still referred
through the whole path list parsing (e.g. is_active_nid()), we should
clear these path instances as well.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Since some codecs can choose the aamix as a capture source, we should
support it as well.  When spec->add_stereo_mix_input flag is set, the
parser checks the availability of aamix as the input source, and adds
the paths automatically when possible.
Signed-off-by: Takashi Iwai <tiwai@suse.de>

In the current parser code, the input_paths[] may become inconsistent
when some of detected ADCs are dropped due to incomplete inputs, since
the driver rearranges only adc_nids[] but doesn't touch input_paths[].

This patch fixes the issue, and also it optimizes the reachability
checks by simply referring to the parsed input_paths[] instead of
calling is_reachable() again for each connection.
Signed-off-by: Takashi Iwai <tiwai@suse.de>