The error message was:

m25p80 spi32766.0: unrecognized JEDEC id bytes: 00,  0,  0

The new error message:

m25p80 spi32766.0: unrecognized JEDEC id bytes: 00, 00, 00
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

for_each_child_of_node performs an of_node_get on each iteration, so
a break out of the loop requires an of_node_put.

A simplified version of the semantic patch that fixes this problem is as
follows (http://coccinelle.lip6.fr):

// <smpl>
@@
expression root,e;
local idexpression child;
@@

 for_each_child_of_node(root, child) {
   ... when != of_node_put(child)
       when != e = child
(
   return child;
|
+  of_node_put(child);
?  return ...;
)
   ...
 }
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

This patch addresses two related memory management issues in the probe
function:

1. for_each_available_child_of_node performs an of_node_get on each
iteration, so a break out of the loop requires an of_node_put.

A simplified version of the semantic patch that fixes this problem is as
follows (http://coccinelle.lip6.fr):

// <smpl>
@@
expression root,e;
local idexpression child;
@@

 for_each_available_child_of_node(root, child) {
   ... when != of_node_put(child)
       when != e = child
(
   return child;
|
+  of_node_put(child);
?  return ...;
)
   ...
 }
// </smpl>

2. The devm_kzalloc'd data is not used if brcmnand_init_cs fails.  Free it
immediately, using devm_kfree in this case, instead of waiting for the
remove function.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

If an error occurs in flash above 4GB in PIO mode then the EXT_ADDR
registers will be set to the location of the error and never cleared.

Reset them to 0 before reading.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

The linux/mtd/map.h header file is included by a couple of
platform specific files that are built even when CONFIG_MTD
is disabled, and we always get

 warning "No CONFIG_MTD_MAP_BANK_WIDTH_xx selected. No NOR chip support can work"

in that case. This adds an #ifdef around the pointless warning,
as everything is really fine when we don't build the drivers
anyway.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

MTD allows compile-time configuration of the possible CFI geometry
settings that are allowed by the kernel, but that includes a couple of
invalid configurations, where no bank width or no interleave setting
is allowed. These are then caught with a compile-time warning:

include/linux/mtd/cfi.h:76:2: warning: #warning No CONFIG_MTD_CFI_Ix selected. No NOR chip support can work.
include/linux/mtd/map.h:145:2: warning: #warning "No CONFIG_MTD_MAP_BANK_WIDTH_xx selected. No NOR chip support can work"

This is a bit annoying for randconfig tests, and can be avoided if
we change the Kconfig logic to always select the simplest configuration
when no other one is enabled.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

So far struct spi_nor was using just a pointer to struct mtd_info so it
wasn't needed to have it fully defined there. After recent change we
embed whole struct so we need to include a proper header.

Fixes: 19763671 ("mtd: spi-nor: embed struct mtd_info within struct spi_nor")
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Add spi nor flash driver for mediatek controller
Signed-off-by: Bayi Cheng <bayi.cheng@mediatek.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

All atmel_nand_caps are never modified, consitify them.
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Acked-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Most parsers can be handled with our new boilerplate-reducing macro.
There are a few that can't be (cmdlineparts and ofpart).

Also kill off the owner assignments, since register_mtd_parser() now
takes care of that.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

This can help eliminate some boilerplate by generating the module_init()
and module_exit() functions, and by automatically assigning the module
owner.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Pull the supported chip names from drivers/mtd/devices/m25p80.c and stop
pointing readers to Linux code.

Also (although I see this habit repeated throughout the
Documentation/devicetree/bindings/ tree), stop using the title "driver"
in this file, when we're trying explicitly to describe hardware, not
software.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: <devicetree@vger.kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>

I overlooked a few comments in commit 8947e396 ("Documentation: dt:
mtd: replace "nor-jedec" binding with "jedec, spi-nor""). Fix these up
now.
Suggested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>

Commit 43163022 ("mtd: m25p80: allow arbitrary OF matching for
"jedec,spi-nor"") moved the "jedec,spi-nor" handling from the
spi_device_id table to the of_match_table, to better handle matching
complex device tree compatible strings. With that patch, device tree
support works as expected when m25p80.c is built into the kernel.

However, that commit ignored the fact that:

 (1) (non-DT) platform devices might want to use the "spi-nor" string
     for matching with this driver, rather than picking an arbitrary one
     like "m25p80"
 (2) the core SPI uevent/modalias code doesn't yet support kernel module
     autoloading via of_match_table strings; so for DT-based devices, it
     will only report (part of) the first compatible string used

Problem (1) has been reported previously, and I forgot to patch it up
afterward.

Problem (2) was noticed recently here:
http://lists.infradead.org/pipermail/linux-mtd/2015-October/062369.html
https://lkml.org/lkml/2015/11/12/574

Specifically, this patch fixes m25p80.ko module autoloading for cases
like this:

	flash@xxx {
		compatible = "jedec,spi-nor";
		...
	};

because modalias of "spi:spi-nor" (the only module loading info provided
by the SPI core for this device) will now be listed as an alias in
m25p80.ko.

Notably, it does *not* help cases like this:

	flash@xxx {
		compatible = "vendor,shiny-new-device", "jedec,spi-nor";
		...
	};

unless we also list "shiny-new-device" in m25p_ids[]. There has been
discussion on future work for this issue here:
https://lkml.org/lkml/2015/11/12/574

Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>

according datasheet both chips can erase 4kByte sectors individually
Signed-off-by: Andreas Fenkart <andreas.fenkart@dev.digitalstrom.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Just use the spi-nor default instead.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Some spi-nor drivers perform sector erase by duplicating their
write_reg() command. Let's not require that the driver fill this out,
and provide a default instead.

Tested on m25p80.c and Medatek's MT8173 SPI NOR flash driver.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

mtd_to_nand() has been introduced to hide accesses to mtd->priv.
All NAND controller drivers should use it instead of directly accessing
the ->priv field.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

In case other subsystems want to merge in this helper for use in their
drivers, let's bring in that development separately from the rest of
MTD -next development.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Some drivers are retrieving the nand_chip pointer using the container_of
macro on a struct wrapping both the nand_chip and the mtd_info struct while
the standard way of retrieving this pointer is through mtd->priv.
Provide an helper to do that.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

The ->priv field of the mtd_info object attached to a nand_chip device
should point to the nand_chip device. The pxa and cafe drivers are
assigning this field their own private structure, which works fine as long
as the nand_chip field is the first one in the driver private struct but
seems a bit fragile.
Fix that by setting mtd->priv to point the nand_chip field and assigning
chip->priv to the private structure head.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

AFAIR this driver was never tested with subpage read support, and this
code is currently unused because we don't set the NAND_SUBPAGE_READ
flag. It can be resurrected if someone tests it properly.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Tested-by: Ray Jui <rjui@broadcom.com>

The read_byte() handling for accessing the flash cache has some awkward
swapping being done in the read_byte() function. Let's just make this a
byte array, and do the swapping with the word-level macros during the
initial buffer copy.

This is just a refactoring patch, with no (intended) functional change.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Clay McClure <clay@daemons.net>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: <bcm-kernel-feedback-list@broadcom.com>
Tested-by: Clay McClure <clay@daemons.net>

It is theoretically possible to probe this driver without a matching
device tree, so let's guard against this.

Also, use the of_device_get_match_data() helper to make this a bit
simpler.

Coverity complained about this one.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Han xu <han.xu@freescale.com>

This patch correct some representation errors, add a little
clarification in some places, and fix indentation problems
for pseudo code.

It also delete one more white space for one place.
Signed-off-by: Wang YanQing <udknight@gmail.com>
[Brian: a few tweaks]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Doing a bit-or operation with zero is pointless.

Remove this unneeded bit-or.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

As Cyrille noted [1], this line is wrong.

[1] http://lists.infradead.org/pipermail/linux-mtd/2015-September/061725.htmlSigned-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Cyrille Pitchen <cyrille.pitchen@atmel.com>

do_div() is meant to be used with an unsigned dividend.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

The NAND clock can be disabled on suspend and enabled on resume.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

This macro is not used anymore, so it's just dead code.
Remove it.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Currently, the driver is trying to detect the presence of a chip
by issuing a RESET command before nand_scan_ident. This seems completely
redundant, and is also a layering violation as nand_scan_ident is in charge
of device detection.

This commit removes the RESET command use, and moves the initial
timing configuration to pxa3xx_nand_config_ident.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

This commit simplifies the initial configuration performed
by pxa3xx_nand_scan. No functionality change is intended.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

The Data Flash Control Register (NDCR) contains two types
of parameters: those that are needed for device identification,
and those that can only be set after device identification.

Therefore, the driver can't set them all at once and instead
needs to configure the first group before nand_scan_ident()
and the second group later.

Let's split pxa3xx_nand_config in two halves, and set the
parameters that depend on the device geometry once this is known.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

The chunk size represents the size of the data chunks, which
is used by the controllers that allow to split transfered data.

However, the initial chunk size is used in a non-splitted way,
during device identification. Therefore, it must be large enough
for all the NAND commands issued during device identification.
This includes NAND_CMD_PARAM which was recently changed to
transfer up to 2048 bytes (for the redundant parameter pages).

Thus, the initial chunk size should be 2048 as well.

On Armada 370/XP platforms (NFCv2) booted without the keep-config
devicetree property, this commit fixes a timeout on the NAND_CMD_PARAM
command:

  [..]
  pxa3xx-nand f10d0000.nand: This platform can't do DMA on this device
  pxa3xx-nand f10d0000.nand: Wait time out!!!
  nand: device found, Manufacturer ID: 0x2c, Chip ID: 0x38
  nand: Micron MT29F8G08ABABAWP
  nand: 1024 MiB, SLC, erase size: 512 KiB, page size: 4096, OOB size: 224
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

We need to be able to build the jz4740_nand driver.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

If multiple NAND chips are registered to the same controller, then when
rebooting the system, the first one will grab the controller lock, while
the second will wait forever for the first one to release it. i.e., a
classic deadlock.

This problem was solved for a similar case (suspend/resume) back in
commit 6b0d9a84 ("mtd: nand: fix multi-chip suspend problem"), and
the shutdown state really isn't much different for us, so rather than
adding a new special case to nand_get_device(), we can just overload the
FL_PM_SUSPENDED state.

Now, multiple chips can "get" the same controller lock (preventing
further I/O), while we still allow other chips to pass through
nand_shutdown().

Original report:
http://thread.gmane.org/gmane.linux.drivers.mtd/59726
http://lists.infradead.org/pipermail/linux-mtd/2015-July/059992.html

Fixes: 72ea4036 ("mtd: nand: added nand_shutdown")
Reported-by: Andrew E. Mileski <andrewm@isoar.ca>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: Andrew E. Mileski <andrewm@isoar.ca>
Acked-by: Scott Branden <sbranden@broadcom.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>

Fallout from commit 832f5dac ("MIPS: Remove all the uses of custom gpio.h")

We see errors like this:

drivers/mtd/nand/jz4740_nand.c: In function 'jz_nand_detect_bank':
drivers/mtd/nand/jz4740_nand.c:340:9: error: 'JZ_GPIO_MEM_CS0' undeclared (first use in this function)
drivers/mtd/nand/jz4740_nand.c:340:9: note: each undeclared identifier is reported only once for each function it appears in
drivers/mtd/nand/jz4740_nand.c:359:2: error: implicit declaration of function 'jz_gpio_set_function' [-Werror=implicit-function-declaration]
drivers/mtd/nand/jz4740_nand.c:359:29: error: 'JZ_GPIO_FUNC_MEM_CS0' undeclared (first use in this function)
drivers/mtd/nand/jz4740_nand.c:399:29: error: 'JZ_GPIO_FUNC_NONE' undeclared (first use in this function)
drivers/mtd/nand/jz4740_nand.c: In function 'jz_nand_probe':
drivers/mtd/nand/jz4740_nand.c:528:13: error: 'JZ_GPIO_MEM_CS0' undeclared (first use in this function)
drivers/mtd/nand/jz4740_nand.c: In function 'jz_nand_remove':
drivers/mtd/nand/jz4740_nand.c:555:14: error: 'JZ_GPIO_MEM_CS0' undeclared (first use in this function)

Patched similarly to:

https://patchwork.linux-mips.org/patch/11089/

Fixes: 832f5dac ("MIPS: Remove all the uses of custom gpio.h")
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Sync up with the upstream development.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>

Pull perf updates from Thomas Gleixner:
 "Mostly updates to the perf tool plus two fixes to the kernel core code:

   - Handle tracepoint filters correctly for inherited events (Peter
     Zijlstra)

   - Prevent a deadlock in perf_lock_task_context (Paul McKenney)

   - Add missing newlines to some pr_err() calls (Arnaldo Carvalho de
     Melo)

   - Print full source file paths when using 'perf annotate --print-line
     --full-paths' (Michael Petlan)

   - Fix 'perf probe -d' when just one out of uprobes and kprobes is
     enabled (Wang Nan)

   - Add compiler.h to list.h to fix 'make perf-tar-src-pkg' generated
     tarballs, i.e. out of tree building (Arnaldo Carvalho de Melo)

   - Add the llvm-src-base.c and llvm-src-kbuild.c files, generated by
     the 'perf test' LLVM entries, when running it in-tree, to
     .gitignore (Yunlong Song)

   - libbpf error reporting improvements, using a strerror interface to
     more precisely tell the user about problems with the provided
     scriptlet, be it in C or as a ready made object file (Wang Nan)

   - Do not be case sensitive when searching for matching 'perf test'
     entries (Arnaldo Carvalho de Melo)

   - Inform the user about objdump failures in 'perf annotate' (Andi
     Kleen)

   - Improve the LLVM 'perf test' entry, introduce a new ones for BPF
     and kbuild tests to check the environment used by clang to compile
     .c scriptlets (Wang Nan)"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (32 commits)
  perf/x86/intel/rapl: Remove the unused RAPL_EVENT_DESC() macro
  tools include: Add compiler.h to list.h
  perf probe: Verify parameters in two functions
  perf session: Add missing newlines to some pr_err() calls
  perf annotate: Support full source file paths for srcline fix
  perf test: Add llvm-src-base.c and llvm-src-kbuild.c to .gitignore
  perf: Fix inherited events vs. tracepoint filters
  perf: Disable IRQs across RCU RS CS that acquires scheduler lock
  perf test: Do not be case sensitive when searching for matching tests
  perf test: Add 'perf test BPF'
  perf test: Enhance the LLVM tests: add kbuild test
  perf test: Enhance the LLVM test: update basic BPF test program
  perf bpf: Improve BPF related error messages
  perf tools: Make fetch_kernel_version() publicly available
  bpf tools: Add new API bpf_object__get_kversion()
  bpf tools: Improve libbpf error reporting
  perf probe: Cleanup find_perf_probe_point_from_map to reduce redundancy
  perf annotate: Inform the user about objdump failures in --stdio
  perf stat: Make stat options global
  perf sched latency: Fix thread pid reuse issue
  ...