When I cat 'tx_timeout' by sysfs, it displays as follows. It's better to
add a newline for easy reading.

root@syzkaller:~# cat /sys/devices/virtual/net/lo/queues/tx-0/tx_timeout
0root@syzkaller:~#
Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

According to the report of [1], this driver is possible to cause
the following error in ravb_tx_timeout_work().

ravb e6800000.ethernet ethernet: failed to switch device to config mode

This error means that the hardware could not change the state
from "Operation" to "Configuration" while some tx and/or rx queue
are operating. After that, ravb_config() in ravb_dmac_init() will fail,
and then any descriptors will be not allocaled anymore so that NULL
pointer dereference happens after that on ravb_start_xmit().

To fix the issue, the ravb_tx_timeout_work() should check
the return values of ravb_stop_dma() and ravb_dmac_init().
If ravb_stop_dma() fails, ravb_tx_timeout_work() re-enables TX and RX
and just exits. If ravb_dmac_init() fails, just exits.

[1]
https://lore.kernel.org/linux-renesas-soc/20200518045452.2390-1-dirk.behme@de.bosch.com/Reported-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Kuniyuki Iwashima says:

====================
udp: Fix reuseport selection with connected sockets.

This patch set addresses two issues which happen when both connected and
unconnected sockets are in the same UDP reuseport group.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, SO_REUSEPORT does not work well if connected sockets are in a
UDP reuseport group.

Then reuseport_has_conns() returns true and the result of
reuseport_select_sock() is discarded. Also, unconnected sockets have the
same score, hence only does the first unconnected socket in udp_hslot
always receive all packets sent to unconnected sockets.

So, the result of reuseport_select_sock() should be used for load
balancing.

The noteworthy point is that the unconnected sockets placed after
connected sockets in sock_reuseport.socks will receive more packets than
others because of the algorithm in reuseport_select_sock().

    index | connected | reciprocal_scale | result
    ---------------------------------------------
    0     | no        | 20%              | 40%
    1     | no        | 20%              | 20%
    2     | yes       | 20%              | 0%
    3     | no        | 20%              | 40%
    4     | yes       | 20%              | 0%

If most of the sockets are connected, this can be a problem, but it still
works better than now.

Fixes: acdcecc6 ("udp: correct reuseport selection with connected sockets")
CC: Willem de Bruijn <willemb@google.com>
Reviewed-by: Benjamin Herrenschmidt <benh@amazon.com>
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.co.jp>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If an unconnected socket in a UDP reuseport group connect()s, has_conns is
set to 1. Then, when a packet is received, udp[46]_lib_lookup2() scans all
sockets in udp_hslot looking for the connected socket with the highest
score.

However, when the number of sockets bound to the port exceeds max_socks,
reuseport_grow() resets has_conns to 0. It can cause udp[46]_lib_lookup2()
to return without scanning all sockets, resulting in that packets sent to
connected sockets may be distributed to unconnected sockets.

Therefore, reuseport_grow() should copy has_conns.

Fixes: acdcecc6 ("udp: correct reuseport selection with connected sockets")
CC: Willem de Bruijn <willemb@google.com>
Reviewed-by: Benjamin Herrenschmidt <benh@amazon.com>
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.co.jp>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 02288248 ("tipc: eliminate gap indicator from ACK messages")
eliminated sending of the 'gap' indicator in regular ACK messages and
only allowed to build NACK message with enabled probe/probe_reply.
However, necessary correction for building NACK message was missed
in tipc_link_timeout() function. This leads to significant delay and
link reset (due to retransmission failure) in lossy environment.

This commit fixes it by setting the 'probe' flag to 'true' when
the receive deferred queue is not empty. As a result, NACK message
will be built to send back to another peer.

Fixes: 02288248 ("tipc: eliminate gap indicator from ACK messages")
Acked-by: Jon Maloy <jmaloy@redhat.com>
Signed-off-by: Tung Nguyen <tung.q.nguyen@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix the warning: [-Werror=-Wframe-larger-than=]

drivers/net/ethernet/neterion/vxge/vxge-main.c:
In function'VXGE_COMPLETE_VPATH_TX.isra.37':
drivers/net/ethernet/neterion/vxge/vxge-main.c:119:1:
warning: the frame size of 1056 bytes is larger than 1024 bytes

Dropping the NR_SKB_COMPLETED to 16 is appropriate that won't
have much impact on performance and functionality.
Signed-off-by: Bixuan Cui <cuibixuan@huawei.com>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The ag71xx_mdio_probe() forgets to call clk_disable_unprepare() when
of_reset_control_get_exclusive() failed. Add the missed call to fix it.

Fixes: d51b6ce4 ("net: ethernet: add ag71xx driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Huang Guobin <huangguobin4@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The fragment packets do defrag in tcf_ct_handle_fragments
will clear the skb->cb which make the qdisc_skb_cb clear
too. So the qdsic_skb_cb should be store before defrag and
restore after that.
It also update the pkt_len after all the
fragments finish the defrag to one packet and make the
following actions counter correct.

Fixes: b57dc7c1 ("net/sched: Introduce action ct")
Signed-off-by: wenxu <wenxu@ucloud.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

The implementation of s3fwrn5_recv_frame() is supposed to consume skb on
all execution paths. Release skb before returning -ENODEV.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ip_dev_find() call holds net_device reference which is not needed,
use __ip_dev_find() which does not hold reference.

v1->v2:
- Correct submission tree.
- Add fixes tag.

Fixes: cc35c88a ("crypto : chtls - CPL handler definition")
Signed-off-by: Vinay Kumar Yadav <vinay.yadav@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When tls data skb is pending for Tx and tls alert comes , It
is wrongly overwrite the record type of tls data to tls alert
record type. fix the issue correcting it.

v1->v2:
- Correct submission tree.
- Add fixes tag.

Fixes: 6919a826 ("Crypto/chtls: add/delete TLS header in driver")
Signed-off-by: Vinay Kumar Yadav <vinay.yadav@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Shannon Nelson says:

====================
ionic: locking and filter fixes

These patches address an ethtool show regs problem, some locking sightings,
and issues with RSS hash and filter_id tracking after a managed FW update.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The ionic_wait_on_bit_lock() was a open-coded mutex knock-off
used only for protecting the queue reset operations, and there
was no reason not to use the real thing.  We can use the lock
more correctly and to better protect the queue stop and start
operations from cross threading.  We can also remove a useless
and expensive bit operation from the Rx path.

This fixes a case found where the link_status_check from a link
flap could run into an MTU change and cause a crash.

Fixes: beead698 ("ionic: Add the basic NDO callbacks for netdev support")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make sure the RSS hash key is kept across a fw update by not
de-initing it when an update is happening.

Fixes: c672412f ("ionic: remove lifs on fw reset")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

When we replay the rx filters after a fw-upgrade we get new
filter_id values from the FW, which we need to save and update
in our local filter list.  This allows us to delete the filters
with the correct filter_id when we're done.

Fixes: 7e4d4759 ("ionic: replay filters after fw upgrade")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add in a couple of forgotten spinlocks and fix up some of
the debug messages around filter management.

Fixes: c1e329eb ("ionic: Add management of rx filters")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use an offset to write the second half of the regs data into the
second half of the buffer instead of overwriting the first half.

Fixes: 4d03e00a ("ionic: Add initial ethtool support")
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

skb_put_padto() can fail. So check for return type and return NULL
for skb. Caller checks for skb and acts correctly if it is NULL.

Fixes: 6d6148bc ("net: hsr: fix incorrect lsdu size in the tag of HSR frames for small frames")
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bareudp.rst was written before iproute2 gained support for this new
type of tunnel. Therefore, the sample command lines didn't match the
final iproute2 implementation.
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When mlxsw_core_trap_register fails in mlxsw_emad_init,
destroy_workqueue() shouled be called to destroy mlxsw_core->emad_wq.

Fixes: d965465b ("mlxsw: core: Fix possible deadlock")
Signed-off-by: Liu Jian <liujian56@huawei.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When dma_coerce_mask_and_coherent() fails, the alloced netdev need to be freed.

Fixes: 060ad66f ("dpaa_eth: change DMA device")
Signed-off-by: Liu Jian <liujian56@huawei.com>
Acked-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Karsten Graul says:

====================
net/smc: fixes 2020-07-20

Please apply the following patch series for smc to netdev's net tree.

Patch 1 fixes a problem with a buffer that is not put back when the
connection was killed in the meantime.
Patch 2 fixes a wrong behaviour when the maximum dmb buffer count
exceeded.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

There is a current limit of 1920 registered dmb buffers per ISM device
for smc-d. One link group can contain 255 connections, each connection
is using one dmb buffer. When the connection is closed then the
registered buffer is held in a queue and is reused by the next
connection. When a link group is 'full' then another link group is
created and uses an own buffer pool. The link groups are added to a
list using list_add() which puts a new link group to the first position
in the list.
In the situation that many connections are opened (>1920) and a few of
them stay open while others are closed quickly we end up with at least 8
link groups. For a new connection a matching link group is looked up,
iterating over the list of link groups. The trailing 7 link groups
all have registered dmb buffers which could be reused, while the first
link group has only a few dmb buffers and then hit the 1920 limit.
Because the first link group is not full (255 connection limit not
reached) it is chosen and finally the connection falls back to TCP
because there is no dmb buffer available in this link group.
There are multiple ways to fix that: using list_add_tail() allows
to scan older link groups first for free buffers which ensures that
buffers are reused first. This fixes the problem for smc-r link groups
as well. For smc-d there is an even better way to address this problem
because smc-d does not have the 255 connections per link group limit.
So fix the problem for smc-d by allowing large link groups.

Fixes: c6ba7c9b ("net/smc: add base infrastructure for SMC-D and ISM")
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

To get a send slot smc_wr_tx_get_free_slot() is called, which might
wait for a free slot. When smc_wr_tx_get_free_slot() returns there is a
check if the connection was killed in the meantime. In that case don't
only return an error, but also put back the free slot.

Fixes: b2900980 ("net/smc: cancel send and receive for terminated socket")
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

rxrpc_sendmsg() returns EPIPE if there's an outstanding error, such as if
rxrpc_recvmsg() indicating ENODATA if there's nothing for it to read.

Change rxrpc_recvmsg() to return EAGAIN instead if there's nothing to read
as this particular error doesn't get stored in ->sk_err by the networking
core.

Also change rxrpc_sendmsg() so that it doesn't fail with delayed receive
errors (there's no way for it to report which call, if any, the error was
caused by).

Fixes: 17926a79 ("[AF_RXRPC]: Provide secure RxRPC sockets for use by userspace and kernel both")
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'ieee802154-for-davem-2020-07-20' of git://git.kernel.org/pub/scm/linux/kernel/git/sschmidt/wpan

Stefan Schmidt says:

====================
pull-request: ieee802154 for net 2020-07-20

An update from ieee802154 for your *net* tree.

A potential memory leak fix for adf7242 from Liu Jian,
and one more HTTPS link change from Alexander A. Klimov.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver forgets to call clk_disable_unprepare() in error path after
a success calling for clk_prepare_enable().

Fix to goto err_clk_disable if clk_prepare_enable() is successful.

Fixes: c80d36ff ("net: bcmgenet: Use devm_clk_get_optional() to get the clocks")
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Acked-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver forgets to call clk_disable_unprepare() in error path after
a success calling for clk_prepare_enable().

Fix to goto err_clk_disable if clk_prepare_enable() is successful.

Fixes: 99d55638 ("net: bcmgenet: enable NETIF_F_HIGHDMA flag")
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Acked-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.

Deterministic algorithm:
For each file:
  If not .svg:
    For each line:
      If doesn't contain `\bxmlns\b`:
        For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
	  If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
            If both the HTTP and HTTPS versions
            return 200 OK and serve the same content:
              Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Link: https://lore.kernel.org/r/20200719113142.58304-1-grandmaster@al2klimov.deSigned-off-by: Stefan Schmidt <stefan@datenfreihafen.org>

If register_netdevice() is failed, net_device should not be used
because variables are uninitialized or freed.
So, the routine should be stopped immediately.
But, bond_create() doesn't check return value of register_netdevice()
immediately. That will result in a panic because of using uninitialized
or freed memory.

Test commands:
    modprobe netdev-notifier-error-inject
    echo -22 > /sys/kernel/debug/notifier-error-inject/netdev/\
actions/NETDEV_REGISTER/error
    modprobe bonding max_bonds=3

Splat looks like:
[  375.028492][  T193] general protection fault, probably for non-canonical address 0x6b6b6b6b6b6b6b6b: 0000 [#1] SMP DEBUG_PAGEALLOC PTI
[  375.033207][  T193] CPU: 2 PID: 193 Comm: kworker/2:2 Not tainted 5.8.0-rc4+ #645
[  375.036068][  T193] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1ubuntu1 04/01/2014
[  375.039673][  T193] Workqueue: events linkwatch_event
[  375.041557][  T193] RIP: 0010:dev_activate+0x4a/0x340
[  375.043381][  T193] Code: 40 a8 04 0f 85 db 00 00 00 8b 83 08 04 00 00 85 c0 0f 84 0d 01 00 00 31 d2 89 d0 48 8d 04 40 48 c1 e0 07 48 03 83 00 04 00 00 <48> 8b 48 10 f6 41 10 01 75 08 f0 80 a1 a0 01 00 00 fd 48 89 48 08
[  375.050267][  T193] RSP: 0018:ffff9f8facfcfdd8 EFLAGS: 00010202
[  375.052410][  T193] RAX: 6b6b6b6b6b6b6b6b RBX: ffff9f8fae6ea000 RCX: 0000000000000006
[  375.055178][  T193] RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff9f8fae6ea000
[  375.057762][  T193] RBP: ffff9f8fae6ea000 R08: 0000000000000000 R09: 0000000000000000
[  375.059810][  T193] R10: 0000000000000001 R11: 0000000000000000 R12: ffff9f8facfcfe08
[  375.061892][  T193] R13: ffffffff883587e0 R14: 0000000000000000 R15: ffff9f8fae6ea580
[  375.063931][  T193] FS:  0000000000000000(0000) GS:ffff9f8fbae00000(0000) knlGS:0000000000000000
[  375.066239][  T193] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  375.067841][  T193] CR2: 00007f2f542167a0 CR3: 000000012cee6002 CR4: 00000000003606e0
[  375.069657][  T193] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[  375.071471][  T193] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[  375.073269][  T193] Call Trace:
[  375.074005][  T193]  linkwatch_do_dev+0x4d/0x50
[  375.075052][  T193]  __linkwatch_run_queue+0x10b/0x200
[  375.076244][  T193]  linkwatch_event+0x21/0x30
[  375.077274][  T193]  process_one_work+0x252/0x600
[  375.078379][  T193]  ? process_one_work+0x600/0x600
[  375.079518][  T193]  worker_thread+0x3c/0x380
[  375.080534][  T193]  ? process_one_work+0x600/0x600
[  375.081668][  T193]  kthread+0x139/0x150
[  375.082567][  T193]  ? kthread_park+0x90/0x90
[  375.083567][  T193]  ret_from_fork+0x22/0x30

Fixes: e826eafa ("bonding: Call netif_carrier_off after register_netdevice")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The commit below caused a regression for clearfog-gt-8k, where the link
between the switch and the host does not come up.

Investigation revealed two issues:
- MV88E6xxx DSA no longer allows an in-band link to come up as the link
  is programmed to be forced down. Commit "net: dsa: mv88e6xxx: fix
  in-band AN link establishment" addresses this.

- The dts configured dissimilar link modes at each end of the host to
  switch link; the host was configured using a fixed link (so has no
  in-band status) and the switch was configured to expect in-band
  status.

With both issues fixed, the regression is resolved.

Fixes: 34b5e6a3 ("net: dsa: mv88e6xxx: Configure MAC when using fixed link")
Reported-by: Martin Rowe <martin.p.rowe@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

If in-band negotiation or fixed-link modes are specified for a DSA
port, the DSA code will force the link down during initialisation. For
fixed-link mode, this is fine, as phylink will manage the link state.
However, for in-band mode, phylink expects the PCS to detect link,
which will not happen if the link is forced down.

There is a related issue that in in-band mode, the link could come up
while we are making configuration changes, so we should force the link
down prior to reconfiguring the interface mode.

This patch addresses both issues.

Fixes: 3be98b2d ("net: dsa: Down cpu/dsa ports phylink will control")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Karsten Graul says:

====================
net/smc: fixes 2020-07-16

Please apply the following patch series for smc to netdev's net tree.

The patches address problems caused by late or unexpected link layer
control packets, dma sync calls for unmapped memory, freed buffers
that are not removed from the buffer list and a possible null pointer
access that results in a crash.

v1->v2: in patch 4, improve patch description and correct the comment
        for the new mutex
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

When a listen socket is closed then all non-accepted sockets in its
accept queue are to be released. Inside __smc_release() the helper
smc_restore_fallback_changes() restores the changes done to the socket
without to check if the clcsocket has a file set. This can result in
a crash. Fix this by checking the file pointer first.
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Fixes: f536dffc ("net/smc: fix closing of fallback SMC sockets")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Two buffers are allocated for each SMC connection. Each buffer is
added to a buffer list after creation. When the second buffer
allocation fails, the first buffer is freed but not deleted from
the list. This might result in crashes when another connection picks
up the freed buffer later and starts to work with it.
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Fixes: 6511aad3 ("net/smc: change smc_buf_free function parameters")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The dma related ...sync_sg... functions check the link state before the
dma function is actually called. But the check in smc_link_usable()
allows links in ACTIVATING state which are not yet mapped to dma memory.
Under high load it may happen that the sync_sg functions are called for
such a link which results in an debug output like
   DMA-API: mlx5_core 0002:00:00.0: device driver tries to sync
   DMA memory it has not allocated [device address=0x0000000103370000]
   [size=65536 bytes]
To fix that introduce a helper to check for the link state ACTIVE and
use it where appropriate. And move the link state update to ACTIVATING
to the end of smcr_link_init() when most initial setup is done.
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Fixes: d854fcbf ("net/smc: add new link state and related helpers")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As smc client the delete link requests are assigned to the flow when
_any_ flow is active. This may break other flows that do not expect
delete link requests during their handling. Fix that by assigning the
request only when an add link flow is active. With that fix the code
for smc client and smc server is the same, so remove the separate
handling.
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Fixes: 9ec6bf19 ("net/smc: llc_del_link_work and use the LLC flow for delete link")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When a new ib device is up smc will send an add link invitation to the
peer if needed. This is currently done with rudimentary flow control.
Under high workload these add link invitations can disturb other llc
flows because they arrive unexpected. Fix this by integrating the
invitations into the normal llc event flow and handle them as a flow.
While at it, check for already assigned requests in the flow before
the new add link request is assigned.
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Fixes: 1f90a05d ("net/smc: add smcr_port_add() and smcr_link_up() processing")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

To be save from unexpected or late llc response messages check if the
arrived message fits to the current flow type and drop out-of-flow
messages. And drop it when there is already a response assigned to
the flow.
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Fixes: ef79d439 ("net/smc: process llc responses in tasklet context")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>