- 22 Dec, 2014 40 commits
-
-
Andy Lutomirski authored
commit b645af2d upstream. It's possible for iretq to userspace to fail. This can happen because of a bad CS, SS, or RIP. Historically, we've handled it by fixing up an exception from iretq to land at bad_iret, which pretends that the failed iret frame was really the hardware part of #GP(0) from userspace. To make this work, there's an extra fixup to fudge the gs base into a usable state. This is suboptimal because it loses the original exception. It's also buggy because there's no guarantee that we were on the kernel stack to begin with. For example, if the failing iret happened on return from an NMI, then we'll end up executing general_protection on the NMI stack. This is bad for several reasons, the most immediate of which is that general_protection, as a non-paranoid idtentry, will try to deliver signals and/or schedule from the wrong stack. This patch throws out bad_iret entirely. As a replacement, it augments the existing swapgs fudge into a full-blown iret fixup, mostly written in C. It's should be clearer and more correct. Signed-off-by:
Andy Lutomirski <luto@amacapital.net> Reviewed-by:
Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> (cherry picked from commit fd2375c3)
-
Quentin Casasnovas authored
Fixes commit 2f06fa04 which was an incorrect backported version of commit d6b41cb0 upstream. If val_count is zero we return -EINVAL with map->lock_arg locked, which will deadlock the kernel next time we try to acquire this lock. This was introduced by f5942dd ("regmap: fix possible ZERO_SIZE_PTR pointer dereferencing error.") which improperly back-ported d6b41cb0. This issue was found during review of Ubuntu Trusty 3.13.0-40.68 kernel to prepare Ksplice rebootless updates. Fixes: f5942dd ("regmap: fix possible ZERO_SIZE_PTR pointer dereferencing error.") Signed-off-by:
Quentin Casasnovas <quentin.casasnovas@oracle.com> Signed-off-by:
Sasha Levin <sasha.levin@oracle.com>
-
bob picco authored
The T5 (niagara5) has different PCR related HV fast trap values and a new HV API Group. This patch utilizes these and shares when possible with niagara4. We use the same sparc_pmu niagara4_pmu. Should there be new effort to obtain the MCU perf statistics then this would have to be changed. Cc: sparclinux@vger.kernel.org Signed-off-by:
Bob Picco <bob.picco@oracle.com> Signed-off-by:
David S. Miller <davem@davemloft.net> (cherry picked from commit 05aa1651) Signed-off-by:
-
Xiubo Li authored
Since we cannot make sure the 'val_count' will always be none zero here, and then if it equals to zero, the kmemdup() will return ZERO_SIZE_PTR, which equals to ((void *)16). So this patch fix this with just doing the zero check before calling kmemdup(). Signed-off-by:
Xiubo Li <Li.Xiubo@freescale.com> Signed-off-by:
Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org (cherry picked from commit d6b41cb0) Signed-off-by:
-
Bryan O'Donoghue authored
This patch is to enable the USB gadget device for Intel Quark X1000 Signed-off-by:
Bryan O'Donoghue <bryan.odonoghue@intel.com> Signed-off-by:
Bing Niu <bing.niu@intel.com> Signed-off-by:
Alvin (Weike) Chen <alvin.chen@intel.com> Signed-off-by:
Felipe Balbi <balbi@ti.com> (cherry picked from commit a68df706) Signed-off-by:
-
Takashi Iwai authored
In snd_usbmidi_error_timer(), the driver tries to resubmit MIDI input URBs to reactivate the MIDI stream, but this causes the error when some of URBs are still pending like: WARNING: CPU: 0 PID: 0 at ../drivers/usb/core/urb.c:339 usb_submit_urb+0x5f/0x70() URB ef705c40 submitted while active CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.16.6-2-desktop #1 Hardware name: FOXCONN TPS01/TPS01, BIOS 080015 03/23/2010 c0984bfa f4009ed4 c078deaf f4009ee4 c024c884 c09a135c f4009f00 00000000 c0984bfa 00000153 c061ac4f c061ac4f 00000009 00000001 ef705c40 e854d1c0 f4009eec c024c8d3 00000009 f4009ee4 c09a135c f4009f00 f4009f04 c061ac4f Call Trace: [<c0205df6>] try_stack_unwind+0x156/0x170 [<c020482a>] dump_trace+0x5a/0x1b0 [<c0205e56>] show_trace_log_lvl+0x46/0x50 [<c02049d1>] show_stack_log_lvl+0x51/0xe0 [<c0205eb7>] show_stack+0x27/0x50 [<c078deaf>] dump_stack+0x45/0x65 [<c024c884>] warn_slowpath_common+0x84/0xa0 [<c024c8d3>] warn_slowpath_fmt+0x33/0x40 [<c061ac4f>] usb_submit_urb+0x5f/0x70 [<f7974104>] snd_usbmidi_submit_urb+0x14/0x60 [snd_usbmidi_lib] [<f797483a>] snd_usbmidi_error_timer+0x6a/0xa0 [snd_usbmidi_lib] [<c02570c0>] call_timer_fn+0x30/0x130 [<c0257442>] run_timer_softirq+0x1c2/0x260 [<c0251493>] __do_softirq+0xc3/0x270 [<c0204732>] do_softirq_own_stack+0x22/0x30 [<c025186d>] irq_exit+0x8d/0xa0 [<c0795228>] smp_apic_timer_interrupt+0x38/0x50 [<c0794a3c>] apic_timer_interrupt+0x34/0x3c [<c0673d9e>] cpuidle_enter_state+0x3e/0xd0 [<c028bb8d>] cpu_idle_loop+0x29d/0x3e0 [<c028bd23>] cpu_startup_entry+0x53/0x60 [<c0bfac1e>] start_kernel+0x415/0x41a For avoiding these errors, check the pending URBs and skip resubmitting such ones. Reported-and-tested-by:
Stefan Seyfried <stefan.seyfried@googlemail.com> Acked-by:
Clemens Ladisch <clemens@ladisch.de> Cc: <stable@vger.kernel.org> Signed-off-by:
Takashi Iwai <tiwai@suse.de> (cherry picked from commit 66139a48) Signed-off-by:
-
Greg Kroah-Hartman authored
This reverts commit 2dbfff81, which really is commit 558e4736 upstream. Sorry for the confusion, this got applied twice, and reverted once, this is the second revert and I hope to never touch it again... Reported-by:
Lv Zheng <lv.zheng@intel.com> Cc: Alexander Mezin <mezin.alexander@gmail.com> Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Daniel Borkmann authored
To accomodate for enough headroom for tunnels, use MAX_HEADER instead of LL_MAX_HEADER. Robert reported that he has hit after roughly 40hrs of trinity an skb_under_panic() via SCTP output path (see reference). I couldn't reproduce it from here, but not using MAX_HEADER as elsewhere in other protocols might be one possible cause for this. In any case, it looks like accounting on chunks themself seems to look good as the skb already passed the SCTP output path and did not hit any skb_over_panic(). Given tunneling was enabled in his .config, the headroom would have been expanded by MAX_HEADER in this case. Reported-by:
Robert Święcki <robert@swiecki.net> Reference: https://lkml.org/lkml/2014/12/1/507 Fixes: 594ccc14 ("[SCTP] Replace incorrect use of dev_alloc_skb with alloc_skb in sctp_packet_transmit().") Signed-off-by:
Daniel Borkmann <dborkman@redhat.com> Acked-by:
Vlad Yasevich <vyasevich@gmail.com> Acked-by:
Neil Horman <nhorman@tuxdriver.com> Signed-off-by:
-
willy tarreau authored
The mvneta driver sets the amount of Tx coalesce packets to 16 by default. Normally that does not cause any trouble since the driver uses a much larger Tx ring size (532 packets). But some sockets might run with very small buffers, much smaller than the equivalent of 16 packets. This is what ping is doing for example, by setting SNDBUF to 324 bytes rounded up to 2kB by the kernel. The problem is that there is no documented method to force a specific packet to emit an interrupt (eg: the last of the ring) nor is it possible to make the NIC emit an interrupt after a given delay. In this case, it causes trouble, because when ping sends packets over its raw socket, the few first packets leave the system, and the first 15 packets will be emitted without an IRQ being generated, so without the skbs being freed. And since the socket's buffer is small, there's no way to reach that amount of packets, and the ping ends up with "send: no buffer available" after sending 6 packets. Running with 3 instances of ping in parallel is enough to hide the problem, because with 6 packets per instance, that's 18 packets total, which is enough to grant a Tx interrupt before all are sent. The original driver in the LSP kernel worked around this design flaw by using a software timer to clean up the Tx descriptors. This timer was slow and caused terrible network performance on some Tx-bound workloads (such as routing) but was enough to make tools like ping work correctly. Instead here, we simply set the packet counts before interrupt to 1. This ensures that each packet sent will produce an interrupt. NAPI takes care of coalescing interrupts since the interrupt is disabled once generated. No measurable performance impact nor CPU usage were observed on small nor large packets, including when saturating the link on Tx, and this fixes tools like ping which rely on too small a send buffer. If one wants to increase this value for certain workloads where it is safe to do so, "ethtool -C $dev tx-frames" will override this default setting. This fix needs to be applied to stable kernels starting with 3.10. Tested-By:
Maggie Mae Roxas <maggie.mae.roxas@gmail.com> Signed-off-by:
Willy Tarreau <w@1wt.eu> Signed-off-by:
-
Jack Morgenstein authored
Some VF drivers use the upper byte of "param1" (the qp count field) in mlx4_qp_reserve_range() to pass flags which are used to optimize the range allocation. Under the current code, if any of these flags are set, the 32-bit count field yields a count greater than 2^24, which is out of range, and this VF fails. As these flags represent a "best-effort" allocation hint anyway, they may safely be ignored. Therefore, the PF driver may simply mask out the bits. Fixes: c82e9aa0 "mlx4_core: resource tracking for HCA resources used by guests" Signed-off-by:
Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by:
Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by:
-
Thadeu Lima de Souza Cascardo authored
If TX channels are set to 4 and RX channels are set to less than 4, using ethtool -L, the driver will try to initialize more RX channels than it has allocated, causing an oops. This fix only initializes the RX ring if it has been allocated. Signed-off-by:
Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com> Signed-off-by:
-
Yuri Chislov authored
When using GRE redirection in WCCP, it sets the wrong skb->protocol, that is, ETH_P_IP instead of ETH_P_IPV6 for the encapuslated traffic. Fixes: c12b395a ("gre: Support GRE over IPv6") Cc: Dmitry Kozlov <xeb@mail.ru> Signed-off-by:
Yuri Chislov <yuri.chislov@gmail.com> Tested-by:
-
Dmitry Torokhov authored
irq_of_parse_and_map() returns 0 on error (the result is unsigned int), so testing for negative result never works. Signed-off-by:
Dmitry Torokhov <dtor@chromium.org> Signed-off-by:
Tejun Heo <tj@kernel.org> Cc: stable@vger.kernel.org (cherry picked from commit aad0b624) Signed-off-by:
-
Tejun Heo authored
Just like 0x1600 which got blacklisted by 66a7cbc3 ("ahci: disable MSI instead of NCQ on Samsung pci-e SSDs on macbooks"), 0xa800 chokes on NCQ commands if MSI is enabled. Disable MSI. Signed-off-by:
Dominik Mierzejewski <dominik@greysector.net> Link: https://bugzilla.kernel.org/show_bug.cgi?id=89171 Cc: stable@vger.kernel.org (cherry picked from commit 2b21ef0a) Signed-off-by:
-
Devin Ryles authored
This patch adds DeviceIDs for Sunrise Point-LP. Signed-off-by:
Devin Ryles <devin.ryles@intel.com> Signed-off-by:
-
Sakari Ailus authored
commit b31eb901 upstream. Setting a non-settable selection target caused BUG() to be called. The check for valid selections only takes the selection target into account, but does not tell whether it may be set, or only get. Fix the issue by simply returning an error to the user. Signed-off-by:
Sakari Ailus <sakari.ailus@iki.fi> Signed-off-by:
Mauro Carvalho Chehab <mchehab@osg.samsung.com> Signed-off-by:
-
Petr Mladek authored
I was unable too boot 3.18.0-rc6 because of the following kernel panic in drm_calc_vbltimestamp_from_scanoutpos(): [drm] Initialized drm 1.1.0 20060810 [drm] radeon kernel modesetting enabled. [drm] initializing kernel modesetting (RV100 0x1002:0x515E 0x15D9:0x8080). [drm] register mmio base: 0xC8400000 [drm] register mmio size: 65536 radeon 0000:0b:01.0: VRAM: 128M 0x00000000D0000000 - 0x00000000D7FFFFFF (16M used) radeon 0000:0b:01.0: GTT: 512M 0x00000000B0000000 - 0x00000000CFFFFFFF [drm] Detected VRAM RAM=128M, BAR=128M [drm] RAM width 16bits DDR [TTM] Zone kernel: Available graphics memory: 3829346 kiB [TTM] Zone dma32: Available graphics memory: 2097152 kiB [TTM] Initializing pool allocator [TTM] Initializing DMA pool allocator [drm] radeon: 16M of VRAM memory ready [drm] radeon: 512M of GTT memory ready. [drm] GART: num cpu pages 131072, num gpu pages 131072 [drm] PCI GART of 512M enabled (table at 0x0000000037880000). radeon 0000:0b:01.0: WB disabled radeon 0000:0b:01.0: fence driver on ring 0 use gpu addr 0x00000000b0000000 and cpu addr 0xffff8800bbbfa000 [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). [drm] Driver supports precise vblank timestamp query. [drm] radeon: irq initialized. [drm] Loading R100 Microcode radeon 0000:0b:01.0: Direct firmware load for radeon/R100_cp.bin failed with error -2 radeon_cp: Failed to load firmware "radeon/R100_cp.bin" [drm:r100_cp_init] *ERROR* Failed to load firmware! radeon 0000:0b:01.0: failed initializing CP (-2). radeon 0000:0b:01.0: Disabling GPU acceleration [drm] radeon: cp finalized BUG: unable to handle kernel NULL pointer dereference at 000000000000025c IP: [<ffffffff8150423b>] drm_calc_vbltimestamp_from_scanoutpos+0x4b/0x320 PGD 0 Oops: 0000 [#1] SMP Modules linked in: CPU: 1 PID: 1 Comm: swapper/0 Not tainted 3.18.0-rc6-4-default #2649 Hardware name: Supermicro X7DB8/X7DB8, BIOS 6.00 07/26/2006 task: ffff880234da2010 ti: ffff880234da4000 task.ti: ffff880234da4000 RIP: 0010:[<ffffffff8150423b>] [<ffffffff8150423b>] drm_calc_vbltimestamp_from_scanoutpos+0x4b/0x320 RSP: 0000:ffff880234da7918 EFLAGS: 00010086 RAX: ffffffff81557890 RBX: 0000000000000000 RCX: ffff880234da7a48 RDX: ffff880234da79f4 RSI: 0000000000000000 RDI: ffff880232e15000 RBP: ffff880234da79b8 R08: 0000000000000000 R09: 0000000000000000 R10: 000000000000000a R11: 0000000000000001 R12: ffff880232dda1c0 R13: ffff880232e1518c R14: 0000000000000292 R15: ffff880232e15000 FS: 0000000000000000(0000) GS:ffff88023fc40000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b CR2: 000000000000025c CR3: 0000000002014000 CR4: 00000000000007e0 Stack: ffff880234da79d8 0000000000000286 ffff880232dcbc00 0000000000002480 ffff880234da7958 0000000000000296 ffff880234da7998 ffffffff8151b51d ffff880234da7a48 0000000032dcbeb0 ffff880232dcbc00 ffff880232dcbc58 Call Trace: [<ffffffff8151b51d>] ? drm_vma_offset_remove+0x1d/0x110 [<ffffffff8152dc98>] radeon_get_vblank_timestamp_kms+0x38/0x60 [<ffffffff8152076a>] ? ttm_bo_release_list+0xba/0x180 [<ffffffff81503751>] drm_get_last_vbltimestamp+0x41/0x70 [<ffffffff81503933>] vblank_disable_and_save+0x73/0x1d0 [<ffffffff81106b2f>] ? try_to_del_timer_sync+0x4f/0x70 [<ffffffff81505245>] drm_vblank_cleanup+0x65/0xa0 [<ffffffff815604fa>] radeon_irq_kms_fini+0x1a/0x70 [<ffffffff8156c07e>] r100_init+0x26e/0x410 [<ffffffff8152ae3e>] radeon_device_init+0x7ae/0xb50 [<ffffffff8152d57f>] radeon_driver_load_kms+0x8f/0x210 [<ffffffff81506965>] drm_dev_register+0xb5/0x110 [<ffffffff8150998f>] drm_get_pci_dev+0x8f/0x200 [<ffffffff815291cd>] radeon_pci_probe+0xad/0xe0 [<ffffffff8141a365>] local_pci_probe+0x45/0xa0 [<ffffffff8141b741>] pci_device_probe+0xd1/0x130 [<ffffffff81633dad>] driver_probe_device+0x12d/0x3e0 [<ffffffff8163413b>] __driver_attach+0x9b/0xa0 [<ffffffff816340a0>] ? __device_attach+0x40/0x40 [<ffffffff81631cd3>] bus_for_each_dev+0x63/0xa0 [<ffffffff8163378e>] driver_attach+0x1e/0x20 [<ffffffff81633390>] bus_add_driver+0x180/0x240 [<ffffffff81634914>] driver_register+0x64/0xf0 [<ffffffff81419cac>] __pci_register_driver+0x4c/0x50 [<ffffffff81509bf5>] drm_pci_init+0xf5/0x120 [<ffffffff821dc871>] ? ttm_init+0x6a/0x6a [<ffffffff821dc908>] radeon_init+0x97/0xb5 [<ffffffff810002fc>] do_one_initcall+0xbc/0x1f0 [<ffffffff810e3278>] ? __wake_up+0x48/0x60 [<ffffffff8218e256>] kernel_init_freeable+0x18a/0x215 [<ffffffff8218d983>] ? initcall_blacklist+0xc0/0xc0 [<ffffffff818a78f0>] ? rest_init+0x80/0x80 [<ffffffff818a78fe>] kernel_init+0xe/0xf0 [<ffffffff818c0c3c>] ret_from_fork+0x7c/0xb0 [<ffffffff818a78f0>] ? rest_init+0x80/0x80 Code: 45 ac 0f 88 a8 01 00 00 3b b7 d0 01 00 00 49 89 ff 0f 83 99 01 00 00 48 8b 47 20 48 8b 80 88 00 00 00 48 85 c0 0f 84 cd 01 00 00 <41> 8b b1 5c 02 00 00 41 8b 89 58 02 00 00 89 75 98 41 8b b1 60 RIP [<ffffffff8150423b>] drm_calc_vbltimestamp_from_scanoutpos+0x4b/0x320 RSP <ffff880234da7918> CR2: 000000000000025c ---[ end trace ad2c0aadf48e2032 ]--- Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000009 It has helped me to add a NULL pointer check that was suggested at http://lists.freedesktop.org/archives/dri-devel/2014-October/070663.html I am not familiar with the code. But the change looks sane and we need something fast at this stage of 3.18 development. Suggested-by:Helge Deller <deller@gmx.de> Signed-off-by:
Petr Mladek <pmladek@suse.cz> Tested-by:
Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org (cherry picked from commit f5475cc4) Signed-off-by:
-
Grygorii Strashko authored
According to I2C specification the NACK should be handled as follows: "When SDA remains HIGH during this ninth clock pulse, this is defined as the Not Acknowledge signal. The master can then generate either a STOP condition to abort the transfer, or a repeated START condition to start a new transfer." [I2C spec Rev. 6, 3.1.6: http://www.nxp.com/documents/user_manual/UM10204.pdf] Currently the Davinci i2c driver interrupts the transfer on receipt of a NACK but fails to send a STOP in some situations and so makes the bus stuck until next I2C IP reset (idle/enable). For example, the issue will happen during SMBus read transfer which consists from two i2c messages write command/address and read data: S Slave Address Wr A Command Code A Sr Slave Address Rd A D1..Dn A P <--- write -----------------------> <--- read ---------------------> The I2C client device will send NACK if it can't recognize "Command Code" and it's expected from I2C master to generate STP in this case. But now, Davinci i2C driver will just exit with -EREMOTEIO and STP will not be generated. Hence, fix it by generating Stop condition (STP) always when NACK is received. This patch fixes Davinci I2C in the same way it was done for OMAP I2C commit cda2109a ("i2c: omap: query STP always when NACK is received"). Reviewed-by:
Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Reported-by:
Hein Tibosch <hein_tibosch@yahoo.es> Signed-off-by:
Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by:
Wolfram Sang <wsa@the-dreams.de> Cc: stable@kernel.org (cherry picked from commit 9ea359f7) Signed-off-by:
-
Alexander Kochetkov authored
commit 6d9939f6 (i2c: omap: split out [XR]DR and [XR]RDY) changed the way how errata i207 (I2C: RDR Flag May Be Incorrectly Set) get handled. 6d9939f6 code doesn't correspond to workaround provided by errata. According to errata ISR must filter out spurious RDR before data read not after. ISR must read RXSTAT to get number of bytes available to read. Because RDR could be set while there could no data in the receive FIFO. Restored pre 6d9939f6 way of handling errata. Found by code review. Real impact haven't seen. Tested on Beagleboard XM C. Signed-off-by:
Alexander Kochetkov <al.kochet@gmail.com> Fixes: 6d9939f6 i2c: omap: split out [XR]DR and [XR]RDY Tested-by:
-
Alexander Kochetkov authored
commit 1d7afc95 (i2c: omap: ack IRQ in parts) changed the interrupt handler to complete transfers without clearing XRDY (AL case) and ARDY (NACK case) flags. XRDY or ARDY interrupts will be fired again. As a result, ISR keep processing transfer after it was already complete (from the driver code point of view). A didn't see real impacts of the 1d7afc95, but it is really bad idea to have ISR running on user data after transfer was complete. It looks, what 1d7afc95 violate TI specs in what how AL and NACK should be handled (see Note 1, sprugn4r, Figure 17-31 and Figure 17-32). According to specs (if I understood correctly), in case of NACK and AL driver must reset NACK, AL, ARDY, RDR, and RRDY (Master Receive Mode), and NACK, AL, ARDY, and XDR (Master Transmitter Mode). All that is done down the code under the if condition: if (stat & (OMAP_I2C_STAT_ARDY | OMAP_I2C_STAT_NACK | OMAP_I2C_STAT_AL)) ... The patch restore pre 1d7afc95 logic of handling NACK and AL interrupts, so no interrupts is fired after ISR informs the rest of driver what transfer complete. Note: instead of removing break under NACK case, we could just replace 'break' with 'continue' and allow NACK transfer to finish using ARDY event. I found that NACK and ARDY bits usually set together. That case confirm TI wiki: http://processors.wiki.ti.com/index.php/I2C_Tips#Detecting_and_handling_NACK In order if someone interested in the event traces for NACK and AL cases, I sent them to mailing list. Tested on Beagleboard XM C. Signed-off-by:
Aaro Koskinen <aaro.koskinen@iki.fi> Signed-off-by:
-
Seth Forshee authored
These BUGs can be erroneously triggered by frags which refer to tail pages within a compound page. The data in these pages may overrun the hardware page while still being contained within the compound page, but since compound_order() evaluates to 0 for tail pages the assertion fails. The code already iterates through subsequent pages correctly in this scenario, so the BUGs are unnecessary and can be removed. Fixes: f36c3747 ("xen/netfront: handle compound page fragments on transmit") Cc: <stable@vger.kernel.org> # 3.7+ Signed-off-by:
Seth Forshee <seth.forshee@canonical.com> Reviewed-by:
David Vrabel <david.vrabel@citrix.com> Signed-off-by:
-
Daniel Forrest authored
Andrew Morton noticed that the error return from anon_vma_clone() was being dropped and replaced with -ENOMEM (which is not itself a bug because the only error return value from anon_vma_clone() is -ENOMEM). I did an audit of callers of anon_vma_clone() and discovered an actual bug where the error return was being lost. In __split_vma(), between Linux 3.11 and 3.12 the code was changed so the err variable is used before the call to anon_vma_clone() and the default initial value of -ENOMEM is overwritten. So a failure of anon_vma_clone() will return success since err at this point is now zero. Below is a patch which fixes this bug and also propagates the error return value from anon_vma_clone() in all cases. Fixes: ef0855d3 ("mm: mempolicy: turn vma_set_policy() into vma_dup_policy()") Signed-off-by:
Daniel Forrest <dan.forrest@ssec.wisc.edu> Reviewed-by:
Michal Hocko <mhocko@suse.cz> Cc: Konstantin Khlebnikov <koct9i@gmail.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Rik van Riel <riel@redhat.com> Cc: Tim Hartrick <tim@edgecast.com> Cc: Hugh Dickins <hughd@google.com> Cc: Michel Lespinasse <walken@google.com> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: <stable@vger.kernel.org> [3.12+] Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
-
Hugh Dickins authored
I've been seeing swapoff hangs in recent testing: it's cycling around trying unsuccessfully to find an mm for some remaining pages of swap. I have been exercising swap and page migration more heavily recently, and now notice a long-standing error in copy_one_pte(): it's trying to add dst_mm to swapoff's mmlist when it finds a swap entry, but is doing so even when it's a migration entry or an hwpoison entry. Which wouldn't matter much, except it adds dst_mm next to src_mm, assuming src_mm is already on the mmlist: which may not be so. Then if pages are later swapped out from dst_mm, swapoff won't be able to find where to replace them. There's already a !non_swap_entry() test for stats: move that up before the swap_duplicate() and the addition to mmlist. Signed-off-by:
Hugh Dickins <hughd@google.com> Cc: Kelley Nielsen <kelleynnn@gmail.com> Cc: <stable@vger.kernel.org> [2.6.18+] Signed-off-by:
-
Al Viro authored
a) don't bother with ->d_time for positives - we only check it for negatives anyway. b) make sure to set it at unlink and rmdir time - at *that* point soon-to-be negative dentry matches then-current directory contents c) don't go into renaming of old alias in vfat_lookup() unless it has the same parent (which it will, unless we are seeing corrupted image) [hirofumi@mail.parknet.co.jp: make change minimum, don't call d_move() for dir] Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
OGAWA Hirofumi <hirofumi@mail.parknet.co.jp> Cc: <stable@vger.kernel.org> [3.17.x] Signed-off-by:
-
Andrew Morton authored
If kzalloc() failed and then evdev_open_device() fails, evdev_open() will pass a vmalloc'ed pointer to kfree. This might fix https://bugzilla.kernel.org/show_bug.cgi?id=88401, where there was a crash in kfree(). Reported-by:
Christian Casteyde <casteyde.christian@free.fr> Belatedly-Acked-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Cc: Henrik Rydberg <rydberg@euromail.se> Cc: <stable@vger.kernel.org> Signed-off-by:
-
Weijie Yang authored
If a frontswap dup-store failed, it should invalidate the expired page in the backend, or it could trigger some data corruption issue. Such as: 1. use zswap as the frontswap backend with writeback feature 2. store a swap page(version_1) to entry A, success 3. dup-store a newer page(version_2) to the same entry A, fail 4. use __swap_writepage() write version_2 page to swapfile, success 5. zswap do shrink, writeback version_1 page to swapfile 6. version_2 page is overwrited by version_1, data corrupt. This patch fixes this issue by invalidating expired data immediately when meet a dup-store failure. Signed-off-by:
Weijie Yang <weijie.yang@samsung.com> Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Cc: Seth Jennings <sjennings@variantweb.net> Cc: Dan Streetman <ddstreet@ieee.org> Cc: Minchan Kim <minchan@kernel.org> Cc: Bob Liu <bob.liu@oracle.com> Cc: <stable@vger.kernel.org> Signed-off-by:
-
Benjamin Herrenschmidt authored
Some radeon ASICs don't support all 64 address bits of MSIs despite advertising support for 64-bit MSIs in their configuration space. This breaks on systems such as IBM POWER7/8, where 64-bit MSIs can be assigned with some of the high address bits set. This makes use of the newly introduced "no_64bit_msi" flag in structure pci_dev to allow the MSI allocation code to fallback to 32-bit MSIs on those adapters. Signed-off-by:
Benjamin Herrenschmidt <benh@kernel.crashing.org> Reviewed-by:
-
Maurizio Lombardi authored
In some cases, the fcoe_rx_list may contains multiple instances of the same skb (the so called "shared skbs"). the bnx2fc_l2_rcv thread is a loop that extracts a skb from the list, modifies (and destroys) its content and then proceed to the next one. The problem is that if the skb is shared, the remaining instances will be corrupted. The solution is to use skb_share_check() before adding the skb to the fcoe_rx_list. [ 6286.808725] ------------[ cut here ]------------ [ 6286.808729] WARNING: at include/scsi/fc_frame.h:173 bnx2fc_l2_rcv_thread+0x425/0x450 [bnx2fc]() [ 6286.808748] Modules linked in: bnx2x(-) mdio dm_service_time bnx2fc cnic uio fcoe libfcoe 8021q garp stp mrp libfc llc scsi_transport_fc scsi_tgt sg iTCO_wdt iTCO_vendor_support coretemp kvm_intel kvm crct10dif_pclmul crc32_pclmul crc32c_intel e1000e ghash_clmulni_intel aesni_intel lrw gf128mul glue_helper ablk_helper ptp cryptd hpilo serio_raw hpwdt lpc_ich pps_core ipmi_si pcspkr mfd_core ipmi_msghandler shpchp pcc_cpufreq mperf nfsd auth_rpcgss nfs_acl lockd sunrpc dm_multipath xfs libcrc32c ata_generic pata_acpi sd_mod crc_t10dif crct10dif_common mgag200 syscopyarea sysfillrect sysimgblt i2c_algo_bit ata_piix drm_kms_helper ttm drm libata i2c_core hpsa dm_mirror dm_region_hash dm_log dm_mod [last unloaded: mdio] [ 6286.808750] CPU: 3 PID: 1304 Comm: bnx2fc_l2_threa Not tainted 3.10.0-121.el7.x86_64 #1 [ 6286.808750] Hardware name: HP ProLiant DL120 G7, BIOS J01 07/01/2013 [ 6286.808752] 0000000000000000 000000000b36e715 ffff8800deba1e00 ffffffff815ec0ba [ 6286.808753] ffff8800deba1e38 ffffffff8105dee1 ffffffffa05618c0 ffff8801e4c81888 [ 6286.808754] ffffe8ffff663868 ffff8801f402b180 ffff8801f56bc000 ffff8800deba1e48 [ 6286.808754] Call Trace: [ 6286.808759] [<ffffffff815ec0ba>] dump_stack+0x19/0x1b [ 6286.808762] [<ffffffff8105dee1>] warn_slowpath_common+0x61/0x80 [ 6286.808763] [<ffffffff8105e00a>] warn_slowpath_null+0x1a/0x20 [ 6286.808765] [<ffffffffa054f415>] bnx2fc_l2_rcv_thread+0x425/0x450 [bnx2fc] [ 6286.808767] [<ffffffffa054eff0>] ? bnx2fc_disable+0x90/0x90 [bnx2fc] [ 6286.808769] [<ffffffff81085aef>] kthread+0xcf/0xe0 [ 6286.808770] [<ffffffff81085a20>] ? kthread_create_on_node+0x140/0x140 [ 6286.808772] [<ffffffff815fc76c>] ret_from_fork+0x7c/0xb0 [ 6286.808773] [<ffffffff81085a20>] ? kthread_create_on_node+0x140/0x140 [ 6286.808774] ---[ end trace c6cdb939184ccb4e ]--- Signed-off-by:
Maurizio Lombardi <mlombard@redhat.com> Acked-by:
Chad Dupuis <chad.dupuis@qlogic.com> Signed-off-by:
Christoph Hellwig <hch@lst.de> Cc: stable@vger.kernel.org (cherry picked from commit 01a4cc4d) Signed-off-by:
-
Trond Myklebust authored
The currect code for nfsd41_cb_get_slot() and nfsd4_cb_done() has no locking in order to guarantee atomicity, and so allows for races of the form. Task 1 Task 2 ====== ====== if (test_and_set_bit(0) != 0) { clear_bit(0) rpc_wake_up_next(queue) rpc_sleep_on(queue) return false; } This patch breaks the race condition by adding a retest of the bit after the call to rpc_sleep_on(). Signed-off-by:Trond Myklebust <trond.myklebust@primarydata.com> Cc: stable@vger.kernel.org Signed-off-by:
J. Bruce Fields <bfields@redhat.com> (cherry picked from commit c6c15e1e) Signed-off-by:
-
Stanislaw Gruszka authored
RT2800 and newer hardware require padding between header and payload if header length is not multiple of 4. For historical reasons we also align payload to to 4 bytes boundary, but such alignment is not needed on modern H/W. Patch fixes skb_under_panic problems reported from time to time: https://bugzilla.kernel.org/show_bug.cgi?id=84911 https://bugzilla.kernel.org/show_bug.cgi?id=72471 http://marc.info/?l=linux-wireless&m=139108549530402&w=2 https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1087591 Panic happened because we eat 4 bytes of skb headroom on each (re)transmission when sending frame without the payload and the header length not being multiple of 4 (i.e. QoS header has 26 bytes). On such case because paylad_aling=2 is bigger than header_align=0 we increase header_align by 4 bytes. To prevent that we could change the check to: if (payload_length && payload_align > header_align) header_align += 4; but not aligning payload at all is more effective and alignment is not really needed by H/W (that has been tested on OpenWrt project for few years now). Reported-and-tested-by:
Antti S. Lankila <alankila@bel.fi> Debugged-by:
Henrik Asp <solenskiner@gmail.com> Originally-From: Helmut Schaa <helmut.schaa@googlemail.com> Cc: stable@vger.kernel.org Signed-off-by:
Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by:
John W. Linville <linville@tuxdriver.com> (cherry picked from commit cfd9167a) Signed-off-by:
-
Thomas Körper authored
ikfree_skb() is Called in can_free_echo_skb(), which might be called from (TX Error) interrupt, which triggers the folloing warning: [ 1153.360705] ------------[ cut here ]------------ [ 1153.360715] WARNING: CPU: 0 PID: 31 at net/core/skbuff.c:563 skb_release_head_state+0xb9/0xd0() [ 1153.360772] Call Trace: [ 1153.360778] [<c167906f>] dump_stack+0x41/0x52 [ 1153.360782] [<c105bb7e>] warn_slowpath_common+0x7e/0xa0 [ 1153.360784] [<c158b909>] ? skb_release_head_state+0xb9/0xd0 [ 1153.360786] [<c158b909>] ? skb_release_head_state+0xb9/0xd0 [ 1153.360788] [<c105bc42>] warn_slowpath_null+0x22/0x30 [ 1153.360791] [<c158b909>] skb_release_head_state+0xb9/0xd0 [ 1153.360793] [<c158be90>] skb_release_all+0x10/0x30 [ 1153.360795] [<c158bf06>] kfree_skb+0x36/0x80 [ 1153.360799] [<f8486938>] ? can_free_echo_skb+0x28/0x40 [can_dev] [ 1153.360802] [<f8486938>] can_free_echo_skb+0x28/0x40 [can_dev] [ 1153.360805] [<f849a12c>] esd_pci402_interrupt+0x34c/0x57a [esd402] [ 1153.360809] [<c10a75b5>] handle_irq_event_percpu+0x35/0x180 [ 1153.360811] [<c10a7623>] ? handle_irq_event_percpu+0xa3/0x180 [ 1153.360813] [<c10a7731>] handle_irq_event+0x31/0x50 [ 1153.360816] [<c10a9c7f>] handle_fasteoi_irq+0x6f/0x120 [ 1153.360818] [<c10a9c10>] ? handle_edge_irq+0x110/0x110 [ 1153.360822] [<c1011b61>] handle_irq+0x71/0x90 [ 1153.360823] <IRQ> [<c168152c>] do_IRQ+0x3c/0xd0 [ 1153.360829] [<c1680b6c>] common_interrupt+0x2c/0x34 [ 1153.360834] [<c107d277>] ? finish_task_switch+0x47/0xf0 [ 1153.360836] [<c167c27b>] __schedule+0x35b/0x7e0 [ 1153.360839] [<c10a5334>] ? console_unlock+0x2c4/0x4d0 [ 1153.360842] [<c13df500>] ? n_tty_receive_buf_common+0x890/0x890 [ 1153.360845] [<c10707b6>] ? process_one_work+0x196/0x370 [ 1153.360847] [<c167c723>] schedule+0x23/0x60 [ 1153.360849] [<c1070de1>] worker_thread+0x161/0x460 [ 1153.360852] [<c1090fcf>] ? __wake_up_locked+0x1f/0x30 [ 1153.360854] [<c1070c80>] ? rescuer_thread+0x2f0/0x2f0 [ 1153.360856] [<c1074f01>] kthread+0xa1/0xc0 [ 1153.360859] [<c1680401>] ret_from_kernel_thread+0x21/0x30 [ 1153.360861] [<c1074e60>] ? kthread_create_on_node+0x110/0x110 [ 1153.360863] ---[ end trace 5ff83639cbb74b35 ]--- This patch replaces the kfree_skb() by dev_kfree_skb_any(). Signed-off-by:
Thomas Körper <thomas.koerper@esd.eu> Cc: linux-stable <stable@vger.kernel.org> Signed-off-by:
Marc Kleine-Budde <mkl@pengutronix.de> (cherry picked from commit 5247a589) Signed-off-by:
-
Christian Sünkenberg authored
Intel Multi-Flex LUNs choke on REPORT SUPPORTED OPERATION CODES resulting in sd_mod hanging for several minutes on startup. The issue was introduced with WRITE SAME discovery heuristics. Fixes: 5db44863 ("[SCSI] sd: Implement support for WRITE SAME") Signed-off-by:
Christian Sünkenberg <christian.suenkenberg@hfg-karlsruhe.de> Signed-off-by:
-
Thor Thayer authored
An IOCTL call that calls spi_setup() and then dw_spi_setup() will overwrite the persisted last transfer speed. On each transfer, the SPI speed is compared to the last transfer speed to determine if the clock divider registers need to be updated (did the speed change?). This bug was observed with the spidev driver using spi-config to update the max transfer speed. This fix: Don't overwrite the persisted last transaction clock speed when updating the SPI parameters in dw_spi_setup(). On the next transaction, the new speed won't match the persisted last speed and the hardware registers will be updated. On initialization, the persisted last transaction clock speed will be 0 but will be updated after the first SPI transaction. Move zeroed clock divider check into clock change test because chip->clk_div is zero on startup and would cause a divide-by-zero error. The calculation was wrong as well (can't support odd #). Reported-by:
Vlastimil Setka <setka@vsis.cz> Signed-off-by:
Thor Thayer <tthayer@opensource.altera.com> Signed-off-by:
-
Roland Dreier authored
If an initiator sends a zero-length command (e.g. TEST UNIT READY) but sets the transfer direction in the transport layer to indicate a data-out phase, we still shouldn't try to transfer data. At best it's a NOP, and depending on the transport, we might crash on an uninitialized sg list. Reported-by:
Craig Watson <craig.watson@vanguard-rugged.com> Signed-off-by:
Roland Dreier <roland@purestorage.com> Cc: <stable@vger.kernel.org> # 3.1 Signed-off-by:
Nicholas Bellinger <nab@linux-iscsi.org> (cherry picked from commit 885e7b0e) Signed-off-by:
-
Bart Van Assche authored
It is not guaranteed to that srp_sq_size is supported by the HCA. So if we failed to create the QP with ENOMEM, try with a smaller srp_sq_size. Keep it up until we hit MIN_SRPT_SQ_SIZE, then fail the connection. Reported-by:
Mark Lehrer <lehrer@gmail.com> Signed-off-by:
Bart Van Assche <bvanassche@acm.org> Signed-off-by:
Sagi Grimberg <sagig@mellanox.com> Cc: <stable@vger.kernel.org> # 3.4+ Signed-off-by:
-
Greg Kroah-Hartman authored
The xpad wireless endpoint is not a bulk endpoint on my devices, but rather an interrupt one, so the USB core complains when it is submitted. I'm guessing that the author really did mean that this should be an interrupt urb, but as there are a zillion different xpad devices out there, let's cover out bases and handle both bulk and interrupt endpoints just as easily. Signed-off-by:
"Pierre-Loup A. Griffais" <pgriffais@valvesoftware.com> Signed-off-by:
-
Thomas Petazzoni authored
Under extremely rare conditions, in an MPCore node consisting of at least 3 CPUs, two CPUs trying to perform a STREX to data on the same shared cache line can enter a livelock situation. This patch enables the HW mechanism that overcomes the bug. This fixes the incorrect setup of the STREX backoff delay bit due to a wrong description in the specification. Note that enabling the STREX backoff delay mechanism is done by leaving the bit *cleared*, while the bit was currently being set by the proc-v7.S code. [Thomas: adapt to latest mainline, slightly reword the commit log, add stable markers.] Fixes: de490193 ("arm: mm: Add support for PJ4B cpu and init routines") Cc: <stable@vger.kernel.org> # v3.8+ Signed-off-by:
Nadav Haklai <nadavh@marvell.com> Signed-off-by:
Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Acked-by:
Gregory CLEMENT <gregory.clement@free-electrons.com> Acked-by:
Jason Cooper <jason@lakedaemon.net> Signed-off-by:
Russell King <rmk+kernel@arm.linux.org.uk> (cherry picked from commit 995ab518) Signed-off-by:
-
Dmitry Eremin-Solenikov authored
According to the manuals I have, XScale auxiliary register should be reached with opc_2 = 1 instead of crn = 1. cpu_xscale_proc_init correctly uses c1, c0, 1 arguments, but cpu_xscale_do_suspend and cpu_xscale_do_resume use c1, c1, 0. Correct suspend/resume functions to also use c1, c0, 1. The issue was primarily noticed thanks to qemu reporing "unsupported instruction" on the pxa suspend path. Confirmed in PXA210/250 and PXA255 XScale Core manuals and in PXA270 and PXA320 Developers Guides. Harware tested by me on tosa (pxa255). Robert confirmed on pxa270 board. Tested-by:
Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by:
Dmitry Eremin-Solenikov <dbaryshkov@gmail.com> Acked-by:
-
Lv Zheng authored
commit 558e4736 upstream. There is platform refusing to respond QR_EC when SCI_EVT isn't set which is Acer Aspire V5-573G. By disallowing QR_EC to be issued before the previous one has been completed we are able to reduce the possibilities to trigger issues on such platforms. Note that this fix can only reduce the occurrence rate of this issue, but this issue may still occur when such a platform doesn't clear SCI_EVT before or immediately after completing the previous QR_EC transaction. This patch cannot fix the CLEAR_ON_RESUME quirk which also relies on the assumption that the platforms are able to respond even when SCI_EVT isn't set. But this patch is still useful as it can help to reduce the number of scheduled QR_EC work items. Link: https://bugzilla.kernel.org/show_bug.cgi?id=82611Reported-and-tested-by:
Alexander Mezin <mezin.alexander@gmail.com> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Jurgen Kramer authored
This patch adds a USB control message delay quirk for a few specific Marantz/Denon devices. Without the delay the DACs will not work properly and produces the following type of messages: Nov 15 10:09:21 orwell kernel: [ 91.342880] usb 3-13: clock source 41 is not valid, cannot use Nov 15 10:09:21 orwell kernel: [ 91.343775] usb 3-13: clock source 41 is not valid, cannot use There are likely other Marantz/Denon devices using the same USB module which exhibit the same problems. But as this cannot be verified I limited the patch to the devices I could test. The following two devices are covered by this path: - Marantz SA-14S1 - Marantz HD-DAC1 Signed-off-by:
Jurgen Kramer <gtmkramer@xs4all.nl> Cc: <stable@vger.kernel.org> Signed-off-by:
-
