To avoid lines with more than 80 characters and to make the
pl011_int() function more readable, move the workaround out into a
separate function.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Tested-by: Naresh Bhat <nbhat@cavium.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The PL011 register UART_MIS is actually a bitwise AND of the
UART_RIS and the UART_MISC register.
Since the SBSA UART does not include the _MIS register, use the
two separate registers to get the same behaviour. Since we are
inside the spinlock and we read the _IMSC register only once, there
should be no race issue.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Tested-by: Naresh Bhat <nbhat@cavium.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Currently the pl011_probe() function is relying on some AMBA IDs
and a device tree node to initialize the driver and a port.
Both features are not necessarily required for the driver:
- we lack AMBA IDs in the ARM SBSA generic UART and
- we lack a DT node in ACPI systems.
So lets refactor the function to ease later reuse.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Tested-by: Naresh Bhat <nbhat@cavium.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Split the pl011_set_termios() function into smaller chunks to allow
easier reuse later when adding SBSA support.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Tested-by: Naresh Bhat <nbhat@cavium.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Split the pl011_shutdown() function into smaller chunks to allow
easier reuse later when adding SBSA support.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Tested-by: Naresh Bhat <nbhat@cavium.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Split the pl011_startup() function into smaller chunks to allow
easier reuse later when adding SBSA support.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Tested-by: Naresh Bhat <nbhat@cavium.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Although we care about not unregistering the driver if there are
still ports connected during the .remove callback, we do miss this
check in the pl011_probe function. So if the current port allocation
fails, but there are other ports already registered, we will kill
those.
So factor out the port removal into a separate function and use that
in the probe function, too.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Tested-by: Naresh Bhat <nbhat@cavium.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

If the mediatek serial port driver is built-in, but serial
console is disabled in Kconfig (e.g. when the serial driver
itself is a loadable module), we get this build error:

drivers/built-in.o: In function `early_mtk8250_setup':
undefined reference to `early_serial8250_setup'

To avoid that problem, this patch encloses the early_mtk8250_setup
function in #ifdef CONFIG_SERIAL_8250_CONSOLE, the same symbol
that guards the early_serial8250_setup function.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Eddie Huang <eddie.huang@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

A configuration that enables earlycon but not the core console
code causes a link error:

  drivers/built-in.o: In function `setup_earlycon':
  drivers/tty/serial/earlycon.c:70: undefined reference to `uart_parse_earlycon'

That error can be triggered by the newly added samsung earlycon support,
which is missing a 'select' statement.

As suggested by Peter Hurley, solves the problem by moving the
'select SERIAL_EARLYCON' statement to the samsung console driver
option, as it is done by all other console drivers.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: b94ba032 ("serial: samsung: Add support for early console")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The platform_sysrq_reset_seq code was intended as a way for an embedded
platform to provide its own sysrq sequence at compile time. After over
two years, nobody has started using it in an upstream kernel, and
the platforms that were interested in it have moved on to devicetree,
which can be used to configure the sequence without requiring kernel
changes. The method is also incompatible with the way that most
architectures build support for multiple platforms into a single
kernel.

Now the code is producing warnings when built with gcc-5.1:

drivers/tty/sysrq.c: In function 'sysrq_init':
drivers/tty/sysrq.c:959:33: warning: array subscript is above array bounds [-Warray-bounds]
   key = platform_sysrq_reset_seq[i];

We could fix this, but it seems unlikely that it will ever be used,
so let's just remove the code instead. We still have the option to
pass the sequence either in DT, using the kernel command line,
or using the /sys/module/sysrq/parameters/reset_seq file.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 154b7a48 ("Input: sysrq - allow specifying alternate reset sequence")
----
v2: moved sysrq_reset_downtime_ms variable to avoid introducing a compile
    warning when CONFIG_INPUT is disabled
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The function mctrl_gpio_init returns failure if the assignment to any
member of the gpio array results in an error pointer.  So there is no
need to check for such error values in the other functions.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add DMA properties to all SCIF, SCIFA, SCIFB, and HSCIF device nodes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add DMA properties to all SCIF, SCIFA, SCIFB, and HSCIF device nodes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add DMA properties to all SCIF, SCIFA, SCIFB, and HSCIF device nodes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The currently in-use port->startup and port->shutdown are "okay". The
startup part for instance does the tiny omap extra part and invokes
serial8250_do_startup() for the remaining pieces. The workflow in
serial8250_do_startup() is okay except for the part where UART_RX is
read without a check if there is something to read. I tried to
workaround it in commit 0aa525d1 ("tty: serial: 8250_core: read only
RX if there is something in the FIFO") but then reverted it later in
commit ca8bb4ae ("serial: 8250: Revert "tty: serial: 8250_core: read
only RX if there is something in the FIFO"").

This is the second attempt to get it to work on older OMAPs without
breaking other chips this time
Peter Hurley suggested to pull in the few needed lines from
serial8250_do_startup() and drop everything else that is not required
including making it simpler like using just request_irq() instead the
chain handler like it is doing now.
So lets try that.

Fixes: ca8bb4ae ("serial: 8250: Revert "tty: serial: 8250_core:
       read only RX if there is something in the FIFO"")
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

If the call to dmaengine_slave_config() fails, then the DMA buffer will
not be freed/unmapped. Fix this by moving the code that stores the
address of the buffer in the tegra_uart_port structure to before the
call to dmaengine_slave_config().
Reported-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

it seems this is a more typical behaviour from reviewing other console
drivers.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

add overrun error's flag mark and parity's counter, we can show the
statistic from procfs node.

BTW, let the indentation of stick bits configuration look better.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In special condition, when cpu schedule into rx_tmo_process_tl or
rx_dma_complete_tl and all the receive dma tasks have done, it will
go into endless loop because no dma task cookie status be changed.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

>From HW spec, when rxfifo's data is less than AFC_RX_THD(RX threshhold), RTS
signal is active. otherwise, RTS signal is inactive.

Crrently the RX threshhold is set as zero, so RTS has no chance to be
active. This patch replaces the default 0 by a positive number.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

differentiate difference port types by re-defining the status MARCO
or putting HW differences into private data of the related ports.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This comment does not reflect the actual code.  It should be 57600,
not 56000.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This comment does not reflect the actual code.  It should be 57600,
not 56000.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In RS485 mode, we may want to set the delay_rts_after_send value to 0.
In the datasheet, the 0 value is said to "disable" the Transmitter Timeguard but
this is exactly the expected behavior if we want no delay...

Moreover, if the value was set to non-zero value by device-tree or earlier
ioctl command, it was impossible to change it back to zero.
Reported-by: Sami Pietikäinen <Sami.Pietikainen@wapice.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: stable@vger.kernel.org  # 3.2+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In commit 02730d3c
(Merge 4.1-rc4 into tty-next), git mismerged some lines,
reintroducing a reference to the removed field
uart_amba_port.tx_irq_seen.  This causes a build failure.

This patch removes the mismerged lines, restoring the code to what
was in tty-next (which was the intention).
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This resolves some tty driver merge issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Two watchdog changes that came through different trees had a non
conflicting conflict, that is, one changed the semantics of a variable
but no actual code conflict happened. So the merge appeared fine, but
the resulting code did not behave as expected.

Commit 195daf66 ("watchdog: enable the new user interface of the
watchdog mechanism") changes the semantics of watchdog_user_enabled,
which thereafter is only used by the functions introduced by
b3738d29 ("watchdog: Add watchdog enable/disable all functions").

There further appears to be a distinct lack of serialization between
setting and using watchdog_enabled, so perhaps we should wrap the
{en,dis}able_all() things in watchdog_proc_mutex.

This patch fixes a s2r failure reported by Michal; which I cannot
readily explain. But this does make the code internally consistent
again.
Reported-and-tested-by: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull MTD fixes from Brian Norris:
 "Two MTD fixes for 4.1:

   - readtest: the signal-handling code was clobbering the error codes
     we should be handling/reporting in this test, rendering it useless.
     Noticed by Coverity.

   - the common SPI NOR flash DT binding (merged for 4.1-rc1) is being
     revised, so let's change that before 4.1 is minted"

* tag 'for-linus-20150516' of git://git.infradead.org/linux-mtd:
  Documentation: dt: mtd: replace "nor-jedec" binding with "jedec, spi-nor"
  mtd: readtest: don't clobber error reports

Pull USB fixes from Greg KH:
 "Here are some USB fixes and new device ids for 4.1-rc4.

  All are pretty minor, and have been in linux-next successfully"

* tag 'usb-4.1-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  usb-storage: Add NO_WP_DETECT quirk for Lacie 059f:0651 devices
  Added another USB product ID for ELAN touchscreen quirks.
  xhci: gracefully handle xhci_irq dead device
  xhci: Solve full event ring by increasing TRBS_PER_SEGMENT to 256
  xhci: fix isoc endpoint dequeue from advancing too far on transaction error
  usb: chipidea: debug: avoid out of bound read
  USB: visor: Match I330 phone more precisely
  USB: pl2303: Remove support for Samsung I330
  USB: cp210x: add ID for KCF Technologies PRN device
  usb: gadget: remove incorrect __init/__exit annotations
  usb: phy: isp1301: work around tps65010 dependency
  usb: gadget: serial: fix re-ordering of tx data
  usb: gadget: hid: Fix static variable usage
  usb: gadget: configfs: Fix interfaces array NULL-termination
  usb: gadget: xilinx: fix devm_ioremap_resource() check
  usb: dwc3: dwc3-omap: correct the register macros

Pull tty/serial fixes from Greg KH:
 "Here's some TTY and serial driver fixes for reported issues.

  All of these have been in linux-next successfully"

* tag 'tty-4.1-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  pty: Fix input race when closing
  tty/n_gsm.c: fix a memory leak when gsmtty is removed
  Revert "serial/amba-pl011: Leave the TX IRQ alone when the UART is not open"
  serial: omap: Fix error handling in probe
  earlycon: Revert log warnings

Pull staging / IIO driver fixes from Greg KH:
 "Here's some staging and iio driver fixes to resolve a number of
  reported issues.

  All of these have been in linux-next for a while"

* tag 'staging-4.1-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (31 commits)
  iio: light: hid-sensor-prox: Fix memory leak in probe()
  iio: adc: cc10001: Add delay before setting START bit
  iio: adc: cc10001: Fix regulator_get_voltage() return value check
  iio: adc: cc10001: Fix incorrect use of power-up/power-down register
  staging: gdm724x: Correction of variable usage after applying ALIGN()
  iio: adc: cc10001: Fix the channel number mapping
  staging: vt6655: lock MACvWriteBSSIDAddress.
  staging: vt6655: CARDbUpdateTSF bss timestamp correct tsf counter value.
  staging: vt6655: vnt_tx_packet Correct TX order of OWNED_BY_NIC
  staging: vt6655: Fix 80211 control and management status reporting.
  staging: vt6655: implement IEEE80211_TX_STAT_NOACK_TRANSMITTED
  staging: vt6655: device_free_tx_buf use only ieee80211_tx_status_irqsafe
  staging: vt6656: use ieee80211_tx_info to select packet type.
  staging: rtl8712: freeing an ERR_PTR
  staging: sm750: remove incorrect __exit annotation
  iio: kfifo: Set update_needed to false only if a buffer was allocated
  iio: mcp320x: Fix occasional incorrect readings
  iio: accel: mma9553: check input value for activity period
  iio: accel: mma9553: add enable channel for activity
  iio: accel: mma9551_core: prevent buffer overrun
  ...

Pull char/misc fix from Greg KH:
 "Here is one fix, in the extcon subsystem, that resolves a reported
  issue.

  It's been in linux-next for a number of weeks now, sorry for not
  getting it to you sooner"

* tag 'char-misc-4.1-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  extcon: usb-gpio: register extcon device before IRQ registration

Pull UML hostfs fix from Richard Weinberger:
 "This contains a single fix for a regression introduced in 4.1-rc1"

* 'for-linus-4.1-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml:
  hostfs: Use correct mask for file mode

Pull UBI bufix from Richard Weinberger:
 "This contains a single bug fix for the UBI block driver"

* tag 'upstream-4.1-rc4' of git://git.infradead.org/linux-ubifs:
  UBI: block: Add missing cache flushes

Pull ext4 fixes from Ted Ts'o:
 "Fix a number of ext4 bugs; the most serious of which is a bug in the
  lazytime mount optimization code where we could end up updating the
  timestamps to the wrong inode"

* tag 'for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
  ext4: fix an ext3 collapse range regression in xfstests
  jbd2: fix r_count overflows leading to buffer overflow in journal recovery
  ext4: check for zero length extent explicitly
  ext4: fix NULL pointer dereference when journal restart fails
  ext4: remove unused function prototype from ext4.h
  ext4: don't save the error information if the block device is read-only
  ext4: fix lazytime optimization

Pull btrfs fixes from Chris Mason:
 "The first commit is a fix from Filipe for a very old extent buffer
  reuse race that triggered a BUG_ON.  It hasn't come up often, I looked
  through old logs at FB and we hit it a handful of times over the last
  year.

  The rest are other corners he hit during testing"

* 'for-linus-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  Btrfs: fix race when reusing stale extent buffers that leads to BUG_ON
  Btrfs: fix race between block group creation and their cache writeout
  Btrfs: fix panic when starting bg cache writeout after IO error
  Btrfs: fix crash after inode cache writeback failure