- 29 May, 2013 3 commits
-
-
Emmanuel Grumbach authored
I forgot to take them from TLV and took them from the NVM instead. Signed-off-by:
Emmanuel Grumbach <emmanuel.grumbach@intel.com> Reviewed-by:
Ilan Peer <ilan.peer@intel.com> Signed-off-by:
Johannes Berg <johannes.berg@intel.com>
-
Alexander Bondar authored
If skip over DTIMs is enabled the driver can specify number of DTIMs to skip. This parameter in host-device API implies number of DTIM periods to skip. For example, to skip one DTIM means sleep over two DTIM periods. Change semantics accordingly. Change this parameter's default value. Signed-off-by:
Alexander Bondar <alexander.bondar@intel.com> Reviewed-by:
-
Eytan Lifshitz authored
In order to avoid NIC destruction due to high temperature, CT kill will power down the NIC. To avoid this, thermal throttling will decrease throughput to prevent the NIC from reaching the temperature at which CT kill is performed. Signed-off-by:
Eytan Lifshitz <eytan.lifshitz@intel.com> Signed-off-by:
-
- 27 May, 2013 8 commits
-
-
Emmanuel Grumbach authored
It was set to be FORCED because of a firmware bug which has been fixed. Signed-off-by:
-
Johannes Berg authored
Conflicts: drivers/net/wireless/iwlwifi/mvm/ops.c
-
Alexander Bondar authored
Beacon abort is used by device to increase idle dwell time when system is idle. This algorithm is on top of beacon filtering feature. Enable beacon abort only if power management is enabled. Signed-off-by:
-
Johannes Berg authored
The pointer that gets used is already const, so the structs can obviously be const as well. Reviewed-by:
-
Johannes Berg authored
There are a number of parameters that aren't really hardware specific but rather define how the DVM firmware is used. Move these into the DVM configuration. Reviewed-by:
-
Johannes Berg authored
The next patches will move some more configuration data that isn't needed by mvm into this struct, so rename it now since it won't just be ops. Reviewed-by:
-
Johannes Berg authored
The MVM firmware doesn't communicate this way, it instead assumes D3 configuration is complete after a specific host command (which must be last) has been sent. Handling this bit thus belongs into the firmware API code, i.e. DVM. Signed-off-by:
-
Emmanuel Grumbach authored
In 63b77bf4 iwlwifi: dvm: don't send zeroed LQ cmd I tried to avoid to send zeroed LQ cmd, but I made a (very) stupid mistake in the memcmp. Since this patch has been ported to stable, the fix should go to stable too. This fixes https://bugzilla.kernel.org/show_bug.cgi?id=58341 Cc: stable@vger.kernel.org Reported-by:
Hinnerk van Bruinehsen <h.v.bruinehsen@fu-berlin.de> Signed-off-by:
-
- 16 May, 2013 15 commits
-
-
Johannes Berg authored
The D3 firmware API changed to include a new field, adjust the driver to it to avoid getting an NMI when configuring. Signed-off-by: -
Johannes Berg authored
When different images can (soon) be accessed through this file, storing the section offset/length on first access to the file breaks (or needs manual reset). Avoid this by not storing the offset/length values but using them locally in the function only. That way, the correct values are always used. While at it, correct the check that firmware is loaded. Reviewed-by:
-
Eran Harary authored
If RF-kill is asserted while a device is initialized, the firmware INIT image can now be run to retrieve the NVM data and register to mac80211 properly. Previously, the initialisation would fail in this scenario and the driver wouldn't register with mac80211 at all, making the device unusable. Signed-off-by:
Eran Harary <eran.harary@intel.com> Reviewed-by:
-
Eran Harary authored
Some newer devices will be integrated into the platform more deeply and will not have embedded NVM (EEPROM/OTP). To support such devices the NVM data must be provided by the platform, allow loading the data via request_firmware() and then send it to the device as needed. Signed-off-by:
-
Johannes Berg authored
These messages aren't really useful, suppress them unless EEPROM debugging is turned on. Reviewed-by:
-
Johannes Berg authored
As the new MVM firmware files package the DATA section first, and debugfs files want to access the DATA and not INST section, reverse the order here. This is only relevant for debugfs code that accesses the SRAM DATA section and uses this constant to access the section. Reviewed-by:
-
Johannes Berg authored
If NVM parsing fails and returns NULL, we continue in the code flow and eventually crash accessing the NULL pointer. Return an error from iwl_nvm_init() if the parsing failed. Reviewed-by:
-
Emmanuel Grumbach authored
Signed-off-by:
-
Alexander Bondar authored
Configure power management in the D3 firmware by sending the power table command to it when suspending; this uses some values that are more suitable to a low power state. Signed-off-by:
-
Alexander Bondar authored
New host-device API provides the ability to set the number of DTIMs to skip. Add this parameter to the command and set it (to a sane default value.) Signed-off-by:
-
Emmanuel Grumbach authored
TX_CMD_SEC_MSK was missing. Signed-off-by:
-
Emmanuel Grumbach authored
Move the counter for non-AMPDU frames to mvm. It is needed for the drain flow which happens once the ieee80211_sta has been freed, so keeping it in iwl_mvm_sta which is embed into ieee80211_sta is not a good idea. Also, since its purpose it to remove the STA in the fw only after all the frames for this station have exited the shared Tx queues, we need to decrement it in the reclaim flow. This flow can happen after ieee80211_sta has been removed, which means that we have no iwl_mvm_sta there. So we can't know what is the vif type. Hence, we know audit these frames for all the vif types. In order to avoid spawning sta_drained_wk all the time, we now check that we are in a flow in which draining might happen - only when mvmsta is NULL. This is better than previous code that would spawn sta_drained_wk all the time in AP mode. Cc: stable@vger.kernel.org [3.9] Signed-off-by:
-
Alexander Bondar authored
In the normal flow first MAC_CONTEXT_CMD for particular interface is never sent while associated. The exception is fw restart flow when resuming from suspend when WoWLAN is enabled. In this case successive "add" and "modify" MAC_CONTEXT_CMD commands may be sent with assoc flag set what cause FW mal functioning. To prevent this never set assoc flag in MAC_CONTEXT_CMD with action "add". Cc: stable@vger.kernel.org Signed-off-by:
-
Emmanuel Grumbach authored
Without this command, the firmware will filter out all the multicast frames. Let them all in as for now. Later we will want to optimize this to save power. Cc: stable@vger.kernel.org Signed-off-by:
-
Ilan Peer authored
The FW AUX framework does not handle well cases where time events fail to be scheduled (and as a result issues assert 0x3330). Until a proper fix is in place, WA this by always setting the scan type to SCAN_TYPE_FORCED. Cc: stable@vger.kernel.org Signed-off-by:
-
- 14 May, 2013 2 commits
-
-
Johannes Berg authored
In some botched (!) restart scenarios we seem to get here with a NULL PHY context, so warn and exit instead of crashing. Reported-by:
Omer Kremer <omerx.kremer@intel.com> Reviewed-by:
-
Johannes Berg authored
The D3 image SRAM is overwritten by the runtime image, so it can't be accessed after resume. However, it can be very useful to look at it to know what happened during D3, so add the ability to store the image and make it available in debugfs. Reviewed-by:
-
- 13 May, 2013 11 commits
-
-
Oren Givon authored
Add new device IDs and configurations to support all the devices. Signed-off-by:
Oren Givon <oren.givon@intel.com> Signed-off-by:
-
Ilan Peer authored
The patch is an optimization, that eliminates unnecessary binding context switching and allows the P2P Device MAC to use the same channel as an existing netdev interface. For each ROC call, check if there is already a channel/phy context that can be used for the P2P Device. If such channel is found, unbind the P2P Device from its current phy context, and bind it to the already used channel/phy context. In case that the phy context is shared, and there is a need to change it, create a new phy context, unbind and create a new binding. Signed-off-by:
-
Johannes Berg authored
Some devices don't support VHT (802.11ac) and this is encoded in the data stored in the NVM. Read the flag and use it to set up the VHT capabilities accordingly. Reviewed-by:
-
Johannes Berg authored
Many times, a NIC error is the result of a bad command sent to the device. If the command was sent synchronously, then we'll currently print a message when the command is aborted containing the command. It can be very useful to also see the stack dump though, so also print that. Reviewed-by:
-
Johannes Berg authored
In theory, the firmware format allows changing the data section offset. This may not be used today, but there's no reason for the driver to assume the data section is always at 0x800000 as it can know better. Reviewed-by:
-
Emmanuel Grumbach authored
This will reduce CPU utilization. Instead of waking up the NIC for each Tx manually, the CPU can write to a register that will wake up the NIC automatically. Signed-off-by:
-
Ilan Peer authored
1. All the phy contexts are added immediately after the firmware is loaded and up. 2. Whenever a PHY context needs to be used, its reference counter is incremented and the PHY context is being configured to the appropriate configuration. 3. When a PHY context is no longer needed, its reference count is decremented. 4. PHY contexts are never removed. Signed-off-by:
-
Ilan Peer authored
In current implementation, the phy context is tightly coupled with the channel context. This complicates the possibility of using the same phy context for both netdev interfaces and the P2P Device interface. To loosen this coupling: 1. Manage all the phy contexts in the mvm op mode, and only save the phy context id in the chanctx memory. 2. Reference count the phy contexts and free them only when they are not longer used (both by mac80211 and P2P Device). Signed-off-by:
-
Emmanuel Grumbach authored
Users complained about allocation failures, so we loaded the firmware in small chunks (PAGE_SIZE). This makes the firmware restart considerably slower. So, always prefer to load it in one shot allocating a big chunk of coherent, and use smaller chunks as a fallback solution. On my laptop, this reduces the fw loading time from 120ms to 20ms. Signed-off-by:
Moshe Island <moshe.island@intel.com> Signed-off-by:
-
Hila Gonen authored
Add iwl_beacon_filter_cmd struct, disable and enable beacon filtering as needed. Signed-off-by:
Hila Gonen <hila.gonen@intel.com> Reviewed-by:
-
Emmanuel Grumbach authored
It has nothing to do in FW API. Signed-off-by:
-
- 12 May, 2013 1 commit
-
-
Linus Torvalds authored
-
