Zinitix BT532 is another touch controller that seem to implement the
same interface as an already supported BT541. Add it to the driver.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Nikita Travkin <nikita@trvn.ru>
Link: https://lore.kernel.org/r/20220106072840.36851-5-nikita@trvn.ruSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The supply names of the Zinitix touchscreen were a bit confused, the new
bindings rectifies this.

To deal with old and new devicetrees, first check if we have "vddo" and in
case that exists assume the old supply names. Else go and look for the new
ones.

We cannot just get the regulators since we would get an OK and a dummy
regulator: we need to check explicitly for the old supply name.

Use struct device *dev as a local variable instead of the I2C client since
the device is what we are actually obtaining the resources from.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[Slightly changed the legacy regulator detection]
Signed-off-by: Nikita Travkin <nikita@trvn.ru>
Link: https://lore.kernel.org/r/20220106072840.36851-4-nikita@trvn.ruSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

This converts the Zinitix BT4xx and BT5xx touchscreen bindings to YAML,
fix them up a bit and extends them.

We list all the existing BT4xx and BT5xx components with compatible
strings.  These are all similar, use the same bindings and work in
similar ways.

We rename the supplies from the erroneous vdd/vddo to the actual supply
names vcca/vdd as specified on the actual component. It is long
established that supplies shall be named after the supply pin names of a
component.  The confusion probably stems from that in a certain product
the rails to the component were named vdd/vddo. Drop some notes on how OS
implementations should avoid confusion by first looking for vddo, and if
that exists assume the legacy binding pair and otherwise use vcca/vdd.

Add reset-gpios as sometimes manufacturers pulls a GPIO line to the reset
line on the chip.

Add optional touchscreen-fuzz-x and touchscreen-fuzz-y properties.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
[Fixed dt_schema_check]
Signed-off-by: Nikita Travkin <nikita@trvn.ru>
Link: https://lore.kernel.org/r/20220106072840.36851-3-nikita@trvn.ruSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The power button on Cherry Trail systems with an AXP288 PMIC is connected
to both the power button pin of the PMIC as well as to a power button GPIO
on the Cherry Trail SoC itself. This leads to double power button event
reporting which is a problem.

Since reporting power button presses through the PMIC is not supported on
all PMICs used on Cherry Trail systems, we want to keep the GPIO
power button events, so the axp20x-pek code checks for the presence of
a GPIO power button and in that case does not register its input-device.

On most systems the GPIO power button also can wake-up the system from
suspend, so the axp20x-pek driver would also not register its interrupt
handler. But on some systems there was a bug causing wakeup by the GPIO
power button handler to not work.

Commit 9747070c ("Input: axp20x-pek - always register interrupt
handlers") was added as a work around for this registering the axp20x-pek
interrupts, but not the input-device on Cherry Trail systems.

In the mean time the root-cause of the GPIO power button wakeup events
not working has been found and fixed by the "pinctrl: cherryview: Do not
allow the same interrupt line to be used by 2 pins" patch,
so this is no longer necessary.

This reverts the workaround going back to only registering the
interrupt handlers on systems where we also register the input-device.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20220106111647.66520-1-hdegoede@redhat.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

bitmap_parselist() already clears the 'bits' bitmap, so there is no need
to clear it when it is allocated. This just wastes some cycles.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/d6ee621b9dd75b92f8831db365cee58dc2025322.1640813136.git.christophe.jaillet@wanadoo.frSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The double `the' in a comment is repeated, thus it should be removed.
Signed-off-by: Xiang wangx <wangxiang@cdjrlc.com>
Link: https://lore.kernel.org/r/20211216082735.11948-1-wangxiang@cdjrlc.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Variable penup is assigned a value but penup is never read later, it
is redundant and can be removed.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20211205000525.153999-1-colin.i.king@gmail.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The open delay time has to be applied only on the first sample of the
X/Y coordinates because on the following samples the ADC channel is not
changed. Removing this time from the samples after the first one,
"ti,coordinate-readouts" greater than 1, decreases the total acquisition
time, allowing to increase the number of acquired coordinates in the time
unit.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Link: https://lore.kernel.org/r/20211212125358.14416-4-dariobin@libero.itSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The Z2 step configuration doesn't erase the SEL_INP_SWC_3_0 bit-field
before setting the ADC channel. This way its value could be corrupted by
the ADC channel selected for the Z1 coordinate.

Fixes: 8c896308 ("input: ti_am335x_adc: use only FIFO0 and clean up a little")
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Link: https://lore.kernel.org/r/20211212125358.14416-3-dariobin@libero.itSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

As reported by the STEPCONFIG[1-16] registered field descriptions of the
TI reference manual, for the ADC "in single ended, SEL_INM_SWC_3_0 must
be 1xxx".

Unlike the Y and Z coordinates, this bit has not been set for the step
configuration registers used to sample the X coordinate.

Fixes: 1b8be32e ("Input: add support for TI Touchscreen controller")
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Link: https://lore.kernel.org/r/20211212125358.14416-2-dariobin@libero.itSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Some Silead touchscreens have support for an active (battery powered)
pen, add support for this.

So far pen-support has only been seen on X86/ACPI (non devicetree) devs,
IOW it is not used in actual devicetree files. The devicetree-bindings
maintainers have requested properties like these to not be added to the
devicetree-bindings, so the new properties are deliberately not added
to the existing silead devicetree-bindings documentation.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211122220637.11386-3-hdegoede@redhat.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Unfortunately, at the time of writing this commit message, we have been
unable to get permission from Silead, or from device OEMs, to distribute
the necessary Silead firmware files in linux-firmware.

On a whole bunch of devices the UEFI BIOS code contains a touchscreen
driver, which contains an embedded copy of the firmware. The fw-loader
code has a "platform" fallback mechanism, which together with info on the
firmware from drivers/platform/x86/touchscreen_dmi.c will use the firmware
from the UEFI driver when the firmware is missing from /lib/firmware. This
makes the touchscreen work OOTB without users needing to manually download
the firmware.

The firmware bundled with the original Windows/Android is usually newer
then the firmware in the UEFI driver and it is better calibrated. This
better calibration can lead to significant differences in the reported
min/max coordinates.

Add support for a new (optional) "silead,efi-fw-min-max" property which
provides a set of alternative min/max values to use for the x/y axis when
the EFI embedded firmware is used.

The new property is only used on (x86) devices which do not use devicetree,
IOW it is not used in actual devicetree files. The devicetree-bindings
maintainers have requested properties like these to not be added to the
devicetree-bindings, so the new property is deliberately not added to the
existing silead devicetree-bindings documentation.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211122220637.11386-2-hdegoede@redhat.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

2 small fixes for pen support

1. Set the id.vendor field for the pen input_dev
2. Fix a typo in a comment
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211212124242.81019-5-hdegoede@redhat.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

goodix_get_gpio_config() errors are fatal (abort probe()) so log them
at KERN_ERR level rather then as debug messages.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211212124242.81019-4-hdegoede@redhat.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Some Goodix touchscreens have support for a (Goodix) active pen, add
support for this. The info on how to detect when a pen is down and to
detect when the stylus buttons are pressed was lifted from the out
of tree Goodix driver with pen support written by Adya:
https://gitlab.com/AdyaAdya/goodix-touchscreen-linux-driver/

Since there is no way to tell if pen support is present, the registering
of the pen input_dev is delayed till the first pen event is detected.

This has been tested on a Trekstor Surftab duo W1, a Chuwi Hi13 and
a Cyberbook T116 tablet.

BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=202161
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=204513Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211207100754.31155-3-hdegoede@redhat.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Sync up with the mainline to get the latest APIs and DT bindings.

When converting a rumble into a periodic effect, for compatibility,
the magnitude is effectively calculated using:

magnitude = max(strong_rubble / 3 + weak_rubble / 6, 0x7fff);

The rumble magnitudes are both u16 and the resulting magnitude is
s16. The max is presumably an attempt to limit the result of the
calculation to the maximum possible magnitude for the s16 result,
and thus should be a min.

However in the case of strong = weak = 0xffff, the result of the first
part of the calculation is 0x7fff, meaning that the min would be
redundant anyway, so simply remove the current max.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20211130135039.13726-1-ckeepax@opensource.cirrus.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Don't populate a couple of arrays on the stack but instead make them
static const. Also makes the object code smaller by a few hundred
bytes.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20211129231749.619469-1-colin.i.king@gmail.comSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Improve the query device fields to be more verbose.
Signed-off-by: Alistair Francis <alistair@alistair23.me>
Link: https://lore.kernel.org/r/20211118123545.102872-1-alistair@alistair23.meSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Use the FIELD_PREP() helper, instead of open-coding the same operation.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/f8831b88346b36fc6e01e0910d0db6c94287d2b4.1637593297.git.geert+renesas@glider.beSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

USB control-message timeouts are specified in milliseconds and should
specifically not vary with CONFIG_HZ.

Fixes: 48735862 ("Input: iforce - use DMA-safe buffer when getting IDs from USB")
Signed-off-by: Johan Hovold <johan@kernel.org>
Cc: stable@vger.kernel.org      # 5.3
Link: https://lore.kernel.org/r/20211025115501.5190-1-johan@kernel.orgSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

To make the code easier to read use macros for the bit masks.
Signed-off-by: Alistair Francis <alistair@alistair23.me>
Link: https://lore.kernel.org/r/20211009113707.17568-2-alistair@alistair23.meSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Modern devices may redraw display at 60 Hz, make sure we have one input
sample per one frame. Reduce sample period to 15ms, so we would get up
to 66.6 samples per second, although realistically with all the jitter
and extra scheduling wiggle room, we would end up just above 60 samples
per second. This should be a good compromise between sampling too often
and sampling too seldom.
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20211108114145.84118-1-marex@denx.deSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Currently the ili210x driver implements a threaded interrupt handler which
starts upon edge on the interrupt line, and then polls the touch controller
for samples. Every time a sample is obtained from the controller, the thread
function checks whether further polling is required, and if so, waits fixed
amount of time before polling for next sample.

The delay between consecutive samples can thus vary greatly, because the
I2C transfer required to retrieve the sample from the controller takes
different amount of time on different platforms. Furthermore, different
models of the touch controllers supported by this driver require different
delays during retrieval of samples too.

Instead of waiting fixed amount of time before polling for next sample,
determine how much time passed since the beginning of sampling cycle and
then wait only the remaining amount of time within the sampling cycle.
This makes the driver deliver samples with equal spacing between them.
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20211108005216.480525-1-marex@denx.deSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The ili251x touch controller needs 5ms delay between sending I2C device
address and register address, and, writing or reading register data.

According to downstream ili251x example code, this 5ms delay is not
required when reading touch samples out of the controller. Implement
such a special case.
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20211108005259.480545-1-marex@denx.deSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Some firmwares occasionally report bogus data from trackpoint, with X or Y
displacement being too large (outside of [-127, 127] range). Let's drop such
packets so that we do not generate jumps.
Signed-off-by: Phoenix Huang <phoenix@emc.com.tw>
Tested-by: Yufei Du <yufeidu@cs.unc.edu>
Link: https://lore.kernel.org/r/20210729010940.5752-1-phoenix@emc.com.tw
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

The created rmi device is orphan, which breaks the real device
hierarchy, and can cause some trouble, especially during suspend
and resume sequences. E.g. in case of I2C, rmi dev should be child
of the I2C client device.

Fix this, assigning the transport device as parent of the rmi device.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Link: https://lore.kernel.org/r/1635514971-18415-1-git-send-email-loic.poulain@linaro.orgSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Fujitsu Lifebook T725 laptop requires, like a few other similar
models, the nomux and notimeout options to probe the touchpad
properly.  This patch adds the corresponding quirk entries.

BugLink: https://bugzilla.suse.com/show_bug.cgi?id=1191980Tested-by: Neal Gompa <ngompa13@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20211103070019.13374-1-tiwai@suse.deSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

According to the datasheet "The CAP1206 is pin- and register-compatible
with the CAP1106, with the exception of the GAIN[1:0] bits and ALT_POL
bit"(57). So, this patch aims to disable them as they are no longer
used.
Signed-off-by: Jesse Taube <mr.bossman075@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Commit 83b41248 ("Input: cy8ctmg110_ts - switch to using gpiod API")
remove the last use of <linux/input/cy8ctmg110_pdata.h> but left the header
file behind.  Nothing uses it now, delete it.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Link: https://lore.kernel.org/r/20211102220203.940290-6-corbet@lwn.netSigned-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Merge tag 'perf-tools-fixes-for-v5.15-2021-10-31' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux

Pull perf tools fixes from Arnaldo Carvalho de Melo:

 - Fix compilation of callchain related code on powerpc with gcc11+

 - Fix PERF_SAMPLE_WEIGHT_STRUCT support in 'perf script'

 - Check session->header.env.arch before using it, fixing a segmentation
   fault

 - Suppress 'rm dlfilter' build messages

* tag 'perf-tools-fixes-for-v5.15-2021-10-31' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux:
  perf script: Fix PERF_SAMPLE_WEIGHT_STRUCT support
  perf callchain: Fix compilation on powerpc with gcc11+
  perf script: Check session->header.env.arch before using it
  perf build: Suppress 'rm dlfilter' build message

Pull kvm fixes from Paolo Bonzini:

 - Fixes for s390 interrupt delivery

 - Fixes for Xen emulator bugs showing up as debug kernel WARNs

 - Fix another issue with SEV/ES string I/O VMGEXITs

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: x86: Take srcu lock in post_kvm_run_save()
  KVM: SEV-ES: fix another issue with string I/O VMGEXITs
  KVM: x86/xen: Fix kvm_xen_has_interrupt() sleeping in kvm_vcpu_block()
  KVM: x86: switch pvclock_gtod_sync_lock to a raw spinlock
  KVM: s390: preserve deliverable_mask in __airqs_kick_single_vcpu
  KVM: s390: clear kicked_mask before sleeping again

-F weight in perf script is broken.

  # ./perf mem record
  # ./perf script -F weight
  Samples for 'dummy:HG' event do not have WEIGHT attribute set. Cannot
print 'weight' field.

The sample type, PERF_SAMPLE_WEIGHT_STRUCT, is an alternative of the
PERF_SAMPLE_WEIGHT sample type. They share the same space, weight. The
lower 32 bits are exactly the same for both sample type. The higher 32
bits may be different for different architecture. For a new kernel on
x86, the PERF_SAMPLE_WEIGHT_STRUCT is used. For an old kernel or other
ARCHs, the PERF_SAMPLE_WEIGHT is used.

With -F weight, current perf script will only check the input string
"weight" with the PERF_SAMPLE_WEIGHT sample type. Because the commit
ea8d0ed6 ("perf tools: Support PERF_SAMPLE_WEIGHT_STRUCT") didn't
update the PERF_SAMPLE_WEIGHT_STRUCT sample type for perf script. For a
new kernel on x86, the check fails.

Use PERF_SAMPLE_WEIGHT_TYPE, which supports both sample types, to
replace PERF_SAMPLE_WEIGHT

Fixes: ea8d0ed6 ("perf tools: Support PERF_SAMPLE_WEIGHT_STRUCT")
Reported-by: Joe Mario <jmario@redhat.com>
Reviewed-by: Kajol Jain <kjain@linux.ibm.com>
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Tested-by: Jiri Olsa <jolsa@redhat.com>
Tested-by: Joe Mario <jmario@redhat.com>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Acked-by: Joe Mario <jmario@redhat.com>
Cc: Andi Kleen <ak@linux.intel.com>
Link: https://lore.kernel.org/r/1632929894-102778-1-git-send-email-kan.liang@linux.intel.comSigned-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

Got following build fail on powerpc:

    CC      arch/powerpc/util/skip-callchain-idx.o
  In function ‘check_return_reg’,
      inlined from ‘check_return_addr’ at arch/powerpc/util/skip-callchain-idx.c:213:7,
      inlined from ‘arch_skip_callchain_idx’ at arch/powerpc/util/skip-callchain-idx.c:265:7:
  arch/powerpc/util/skip-callchain-idx.c:54:18: error: ‘dwarf_frame_register’ accessing 96 bytes \
  in a region of size 64 [-Werror=stringop-overflow=]
     54 |         result = dwarf_frame_register(frame, ra_regno, ops_mem, &ops, &nops);
        |                  ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
  arch/powerpc/util/skip-callchain-idx.c: In function ‘arch_skip_callchain_idx’:
  arch/powerpc/util/skip-callchain-idx.c:54:18: note: referencing argument 3 of type ‘Dwarf_Op *’
  In file included from /usr/include/elfutils/libdwfl.h:32,
                   from arch/powerpc/util/skip-callchain-idx.c:10:
  /usr/include/elfutils/libdw.h:1069:12: note: in a call to function ‘dwarf_frame_register’
   1069 | extern int dwarf_frame_register (Dwarf_Frame *frame, int regno,
        |            ^~~~~~~~~~~~~~~~~~~~
  cc1: all warnings being treated as errors

The dwarf_frame_register args changed with [1],
Updating ops_mem accordingly.

[1] https://sourceware.org/git/?p=elfutils.git;a=commit;h=5621fe5443da23112170235dd5cac161e5c75e65Reviewed-by: Kajol Jain <kjain@linux.ibm.com>
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Acked-by: Mark Wieelard <mjw@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Michael Petlan <mpetlan@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Link: https://lore.kernel.org/r/20210928195253.1267023-1-jolsa@kernel.orgSigned-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

When perf.data is not written cleanly, we would like to process existing
data as much as possible (please see f_header.data.size == 0 condition
in perf_session__read_header). However, perf.data with partial data may
crash perf. Specifically, we see crash in 'perf script' for NULL
session->header.env.arch.

Fix this by checking session->header.env.arch before using it to determine
native_arch. Also split the if condition so it is easier to read.

Committer notes:

If it is a pipe, we already assume is a native arch, so no need to check
session->header.env.arch.
Signed-off-by: Song Liu <songliubraving@fb.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: kernel-team@fb.com
Cc: stable@vger.kernel.org
Link: http://lore.kernel.org/lkml/20211004053238.514936-1-songliubraving@fb.comSigned-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

The following build message:

	rm dlfilters/dlfilter-test-api-v0.o

is unwanted.

The object file is being treated as an intermediate file and being
automatically removed. Mark the object file as .SECONDARY to prevent
removal and hence the message.
Requested-by: Arnaldo Carvalho de Melo <acme@kernel.org>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Link: http://lore.kernel.org/lkml/20210930062849.110416-1-adrian.hunter@intel.comSigned-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

Pull SCSI fixes from James Bottomley:
 "Three small fixes, all in drivers, and one sizeable update to the UFS
  driver to remove the HPB 2.0 feature that has been objected to by Jens
  and Christoph.

  Although the UFS patch is large and last minute, it's essentially the
  least intrusive way of resolving the objections in time for the 5.15
  release"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: ufs: ufshpb: Remove HPB2.0 flows
  scsi: mpt3sas: Fix reference tag handling for WRITE_INSERT
  scsi: ufs: ufs-exynos: Correct timeout value setting registers
  scsi: ibmvfc: Fix up duplicate response detection

Pull clk fix from Stephen Boyd:
 "One fix for the composite clk that broke when we changed this clk type
  to use the determine_rate instead of round_rate clk op by default.
  This caused lots of problems on Rockchip SoCs because they heavily use
  the composite clk code to model the clk tree"

* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
  clk: composite: Also consider .determine_rate for rate + mux composites

Pull RISC-V fixes from Palmer Dabbelt:
 "These are pretty late, but they do fix concrete issues.

   - ensure the trap vector's address is aligned.

   - avoid re-populating the KASAN shadow memory.

   - allow kasan to build without warnings, which have recently become
     errors"

* tag 'riscv-for-linus-5.15-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
  riscv: Fix asan-stack clang build
  riscv: Do not re-populate shadow memory with kasan_populate_early_shadow
  riscv: fix misalgned trap vector base address