From the perspective of controller, global suspend means there is no
SET_FEATURE (DEVICE_REMOTE_WAKEUP) and controller would drop the
firmware. It would consume less power. So we should not send this kind
of SET_FEATURE when host goes to suspend state.
Otherwise, when making device enter selective suspend, host should send
SET_FEATURE to make sure the firmware remains.
Signed-off-by: Alex Lu <alex_lu@realsil.com.cn>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

If CONFIG_ACPI is not set, gcc warn this:

drivers/bluetooth/hci_bcm.c:831:39: warning:
 acpi_bcm_int_last_gpios defined but not used [-Wunused-const-variable=]
drivers/bluetooth/hci_bcm.c:838:39: warning:
 acpi_bcm_int_first_gpios defined but not used [-Wunused-const-variable=]

move them to #ifdef CONFIG_ACPI block.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The qca_data structure is allocated with kzalloc() and hence
zero-initialized. Remove a bunch of unnecessary explicit
initializations of struct members to zero.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

Changes made to add support for fast advertising interval
as per core 4.1 specification, section 9.3.11.2.

A peripheral device entering any of the following GAP modes and
sending either non-connectable advertising events or scannable
undirected advertising events should use adv_fast_interval2
(100ms - 150ms) for adv_fast_period(30s).

         - Non-Discoverable Mode
         - Non-Connectable Mode
         - Limited Discoverable Mode
         - General Discoverable Mode
Signed-off-by: Spoorthi Ravishankar Koppad <spoorthix.k@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>

The UPS feature only works for runtime suspend, so UPS flags only
need to be set before enabling runtime suspend. Therefore, I create
a struct to record relative information, and use it before runtime
suspend.

All chips could record such information, even though not all of
them support the feature of UPS. Then, some functions could be
combined.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move the static keyword to the front of declaration of g_dsaf_mode_match,
and resolve the following compiler warning that can be seen when building
with warnings enabled (W=1):

drivers/net/ethernet/hisilicon/hns/hns_dsaf_main.c:27:1: warning:
  ‘static’ is not at beginning of declaration [-Wold-style-declaration]
Signed-off-by: Krzysztof Wilczynski <kw@linux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move the static keyword to the front of declaration of iwarp_state_names,
and resolve the following compiler warning that can be seen when building
with warnings enabled (W=1):

drivers/net/ethernet/qlogic/qed/qed_iwarp.c:385:1: warning:
  ‘static’ is not at beginning of declaration [-Wold-style-declaration]

Also, resolve checkpatch.pl script warning:

WARNING: static const char * array should probably be
  static const char * const
Signed-off-by: Krzysztof Wilczynski <kw@linux.com>
Acked-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use %*ph format to print small buffer as hex string.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Harini Katakam says:

====================
Fix GMII2RGMII private field

Fix the usage of external phy's priv field by gmii2rgmii driver.

Based on net-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Use set/get drv data in phydev's mdio device instead. Phy device priv
field maybe used by the external phy driver and should not be
overwritten.
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add set/get drv_data helpers for mdio device.
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Arseny Solokha says:

====================
gianfar: some assorted cleanup

This is a cleanup series for the gianfar Ethernet driver, following up a
discussion in [1]. It is intended to precede a conversion of gianfar from
PHYLIB to PHYLINK API, which will be submitted later in its version 2.
However, it won't make a conversion cleaner, except for the last patch in
this series. Obviously this series is not intended for -stable.

The first patch looks super controversial to me, as it moves lots of code
around for the sole purpose of getting rid of static forward declarations
in two translation units. On the other hand, this change is purely
mechanical and cannot do any harm other than cluttering git blame output.
I can prepare an alternative patch for only swapping adjacent functions
around, if necessary.

The second patch is a trivial follow-up to the first one, making functions
that are only called from the same translation unit static.

The third patch removes some now unused macro and structure definitions
from gianfar.h, slipped away from various cleanups in the past.

The fourth patch, also suggested in [1], makes the driver consistently use
PHY connection type value obtained from a Device Tree node, instead of
ignoring it and using the one auto-detected by MAC, when connecting to PHY.
Obviously a value has to be specified correctly in DT source, or omitted
altogether, in which case the driver will fall back to auto-detection. When
querying a DT node, the driver will also take both applicable properties
into account by making a proper API call instead of open-coding the lookup
half-way correctly.

[1] https://lore.kernel.org/netdev/CA+h21hruqt6nGG5ksDSwrGH_w5GtGF4fjAMCWJne7QJrjusERQ@mail.gmail.com/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Historically, gianfar only used phy-connection-type DT property when
connected to PHY in the rgmii-id mode. It ignored the property otherwise,
relying on the connection type auto-detection carried out by MAC and
providing that reconstructed mode to of_phy_connect(). It also did not
consider alternative phy-mode property at all.

Make the driver properly query DT node for PHY connection type first and
use an obtained value if it was specified there. Otherwise, if a particular
DT relies on connection type auto-detection, fall back to reconstructing
the value from MAC registers, as before.
Signed-off-by: Arseny Solokha <asolokha@kb.kras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove now unused macro and structure definitions from gianfar.h that have
accumulated there over time.
Signed-off-by: Arseny Solokha <asolokha@kb.kras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make functions that do not have callers outside the translation unit they
are defined in static.
Signed-off-by: Arseny Solokha <asolokha@kb.kras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove forward declarations of various static functions located in two
driver implementation files and rearrange the corresponding definitions
accordingly.

This patch only introduces mechanical changes, namely it removes forward
declarations and moves function definitions around; it does not change any
functionality.
Signed-off-by: Arseny Solokha <asolokha@kb.kras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jose Abreu says:

====================
net: stmmac: Improvements for -next

Couple of improvements for -next tree. More info in commit logs.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a test to validate the Jumbo Frame support in stmmac in single
channel and multichannel mode.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We are already doing it by default in the TX path so we can also enable
Jumbo Frame support in the RX path independently of MTU value.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Maximum MTU for XGMAC cores is 16k thus the check for presence of XGMAC
shall be done first in order to assign correct value.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

RAVSEL means that only RX side is available for AVB features. As we use
both TX and RX features we need to check if RAVSEL is selected and
disable AVB if only RX side is available.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When RX Watchdog is disabled its currently not possible to configure TX
coalesce settings. Let user configure it anyway.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Only consider that we have an error when HW Timestamping is not enabled
as this can give false positives due to the fact the RX Timestamping in
XGMAC and GMAC cores comes from context descriptors.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement a test for ARP Offload feature.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement the ARP Offload feature in XGMAC cores.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Adds the selftests for L3 and L4 filters with DA/SA/DP/SP support.

Changes from v1:
	- Reduce stack usage (kbuild test robot)
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Implement filters for Layer 3 and Layer 4 using TC Flower API. Add the
corresponding callbacks in XGMAC core.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As we can still use the remaining TC callbacks, e.g. CBS. We should not
fail in the initialization only because RX Parser is not available.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the handling of Receive Buffer Unavailable interrupt in the DMA
handler of XGMAC cores.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We can do better than just return 1 to userspace. Lets return a proper
Linux error code.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'linux-can-next-for-5.4-20190904' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next

Marc Kleine-Budde says:

====================
pull-request: can-next 2019-09-04 j1939

this is a pull request for net-next/master consisting of 21 patches.

the first 12 patches are by me and target the CAN core infrastructure.
They clean up the names of variables , structs and struct members,
convert can_rx_register() to use max() instead of open coding it and
remove unneeded code from the can_pernet_exit() callback.

The next three patches are also by me and they introduce and make use of
the CAN midlayer private structure. It is used to hold protocol specific
per device data structures.

The next patch is by Oleksij Rempel, switches the
&net->can.rcvlists_lock from a spin_lock() to a spin_lock_bh(), so that
it can be used from NAPI (soft IRQ) context.

The next 4 patches are by Kurt Van Dijck, he first updates his email
address via mailmap and then extends sockaddr_can to include j1939
members.

The final patch is the collective effort of many entities (The j1939
authors: Oliver Hartkopp, Bastian Stender, Elenita Hinds, kbuild test
robot, Kurt Van Dijck, Maxime Jayat, Robin van der Gracht, Oleksij
Rempel, Marc Kleine-Budde). It adds support of SAE J1939 protocol to the
CAN networking stack.

SAE J1939 is the vehicle bus recommended practice used for communication
and diagnostics among vehicle components. Originating in the car and
heavy-duty truck industry in the United States, it is now widely used in
other parts of the world.

P.S.: This pull request doesn't invalidate my last pull request:
      "pull-request: can-next 2019-09-03".
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Take only FIB events that are happening in init_net into account. No other
namespaces are supported.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

zhong jiang says:

====================
net: Use kzfree() directly

With the help of Coccinelle. We find some place to replace.

@@
expression M, S;
@@

- memset(M, 0, S);
- kfree(M);
+ kzfree(M);
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Use kzfree instead of memset() + kfree().
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use kzfree instead of memset() + kfree().
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use kzfree() instead of memset() + kfree().
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'linux-can-next-for-5.4-20190903' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next

Marc Kleine-Budde says:

====================
pull-request: can-next 2019-09-03

this is a pull request for net-next/master consisting of 15 patches.

The first patch is by Christer Beskow, targets the kvaser_pciefd driver
and fixes the PWM generator's frequency.

The next three patches are by Dan Murphy, the tcan4x5x is updated to use
a proper interrupts/interrupt-parent DT binding to specify the devices
IRQ line. Further the unneeded wake ups of the device is removed from
the driver.

A patch by me for the mcp25xx driver removes the deprecated board file
setup example. Three patches by Andy Shevchenko simplify clock handling,
update the driver from OF to device property API and simplify the
mcp251x_can_suspend() function.

The remaining 7 patches are by me and clean up checkpatch warnings in
the generic CAN device infrastructure.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The comment we have is just repeating what the code does.
Include the *reason* for the condition instead.

Cc: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jakub Kicinski says:

====================
net/tls: minor cleanups

This set is a grab bag of TLS cleanups accumulated in my tree
in an attempt to avoid merge problems with net. Nothing stands
out. First patch dedups context information. Next control path
locking is very slightly optimized. Fourth patch cleans up
ugly #ifdefs.
====================
Reviewed-by: Boris Pismenny <borisp@mellanox.com>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If retransmit record hint fall into the cleanup window we will
free it by just walking the list. No need to duplicate the code.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>