Add drive strength support for Bitmain BM1880 SoC.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Document drive strength settings for Bitmain BM1880 SoC.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

platform_get_resource() may fail and return NULL, so we should
better check it's return value to avoid a NULL pointer dereference
a bit later in the code.
Signed-off-by: Young Xiao <92siuyang@gmail.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The i.MX8MM pinfunc head file is located in DT folder, correct it.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Some files were missing the appropriate SPDX tags so
fixed it up.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

drivers/pinctrl/bcm/pinctrl-bcm2835.c: In function bcm2835_pctl_dt_node_to_map:
drivers/pinctrl/bcm/pinctrl-bcm2835.c:720:8: error: implicit declaration of function pinconf_generic_dt_node_to_map_all;
drivers/pinctrl/bcm/pinctrl-bcm2835.c: In function bcm2835_pinctrl_probe:
drivers/pinctrl/bcm/pinctrl-bcm2835.c:1022:15: error: struct gpio_chip has no member named of_node
  pc->gpio_chip.of_node = np;
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 0de70495 ("pinctrl: bcm2835: Add support for generic pinctrl binding")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Using STM32 as guinea pig after Alex's initial positive
test to see if this is something we should encourage
in general and make default behaviour.

Cc: Benjamin Gaignard <benjamin.gaignard@st.com>
Cc:  Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Setting this up will configure wake from suspend properly,
and wake only for the interrupts that are setup in wake_mask,
not all interrupts.
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Acked-by: Sean Wang <sean.wang@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

pinctrl variants that include pinctrl-paris.h (and not
pinctrl-mtk-common.h) also need to use pm_ops to setup
wake mask properly, so copy over the pm_ops from common
to paris variant.

It is not easy to merge the 2 copies (or move
mtk_eint_suspend/resume to mtk-eint.c), as we need to
dereference pctrl->eint, and struct mtk_pinctrl *pctl has a
different structure definition for v1 and v2 (which is
what paris variant uses).
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Acked-by: Sean Wang <sean.wang@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Tegra194 has PCIE L5 rst and clkreq pins which need to be controlled
dynamically at runtime. This driver supports change pinmux for these
pins. Pinmux for rest of the pins is set statically by bootloader and
will not be changed by this driver
Signed-off-by: Krishna Yarlagadda <kyarlagadda@nvidia.com>
Signed-off-by: Suresh Mangipudi <smangipudi@nvidia.com>
Tested-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Tegra194 chip has 32 bit pinctrl registers. Existing register defines in
header are only 16 bit.
Modified common pinctrl-tegra driver to support 32 bit registers of
Tegra 194 and later chips.
Signed-off-by: Krishna Yarlagadda <kyarlagadda@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add binding doc for Tegra 194 pinctrl driver.
Signed-off-by: Krishna Yarlagadda <kyarlagadda@nvidia.com>
Tested-by: Vidya Sagar <vidyas@nvidia.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The spelling of configured is incorrect in the documentation. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add pinconf support for Bitmain BM1880 SoC. Pinconf support includes
pin bias, slew rate and schmitt trigger. Drive strength support will
be added later.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Document pinconf bindings for Bitmain BM1880 SoC.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Rework the BM1880 SoC pinmux handling by removing the
BM1880_PINMUX_FUNCTION_MUX define and merging it with the
BM1880_PINMUX_FUNCTION definition. Since the PWM muxing is handled by
generic pin controller in the SoC itself, there is no need to have a
dedicated code to do the muxing in PWM registers. So, lets club all
pinmux handling in the same per pin mux handling code.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Earlier, the PWM registers were included as part of the pinctrl memory
map, but this turned to be useless as the muxing is being handled by the
SoC pin controller itself. So, lets modify the pinctrl memory map to
reflect the same.

Fixes: 07b734fb ("dt-bindings: pinctrl: Add BM1880 pinctrl binding")
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add pinconf support for PIN_CONFIG_OUTPUT_ENABLE and PIN_CONFIG_OUTPUT
in the meson pinctrl driver.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

add support for the pinconf DT property output-enable, output-disable,
output-low and output-high in the meson pinctrl driver.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Convert the STM32 pinctrl binding to DT schema format using json-schema.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

GPIOs are split between several banks (A, B, ...) and each bank can have
up to 16 lines. Those GPIOs could be used as interrupt lines thanks to
exti lines. As there are only 16 exti lines, a mux is used to select which
gpio line is connected to which exti line. Mapping is done as follow:

-A0, B0, C0.. -->exti_line_0 (X0 selected by mux_0)
-A1, B1, C1.. -->exti_line_1 (X1 selected by mux_1)
...

This patch adds a protection to avoid overriding on mux_n for exti_line_n.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Apply suspend/resume management for stm32mp157c MPU.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

During power sequence, GPIO hardware registers could be lost if the power
supply is switched off. Each device using pinctrl API is in charge of
managing pins during suspend/resume sequences. But for pins used as gpio or
irq stm32 pinctrl driver has to save the hardware configuration.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Hogs would create circular device links, so do not link
the device to itself.

Cc: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Set create_link to inform pinctrl core that stmfx wants to create
link with its consumers.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

A pin controller may want to create a link between itself
and its clients to be sure of suspend/resume call ordering.

Introduce link_consumers field in pinctrl_desc structure to let
pinctrl core knows that controller expect to create a link.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
[Renamed create_link to link_consumers]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

ARCH_BRCMSTB needs to use the BCM2835 pin controller for chips
like BCM7211 which adopted that pin controller for GPIO. This
commit makes the option menu configurable with default enabled
for ARCH_BRCMSTB and ARCH_BCM2835.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

BCM7211 has a slightly different block layout and some additional GPIO
registers that were added, document the compatible string.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

add drive-strength bank regiter and bit value for G12A SoC
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

drive-strength-microamp is a new feature needed for G12A SoC.
the default DS setting after boot is usually 500uA and it is not enough for
many functions. We need to be able to set the drive strength to reliably
enable things like MMC, I2C, etc ...
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

rework bias enable/disable part to prepare drive-strength integration
no functional changes
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add optional drive-strength-microamp property
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add drive-strength-microamp property support to allow drive strength in uA
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This property allow drive-strength parameter in uA instead of mA.
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The call to of_parse_phandle returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.

Detected by coccinelle with the following warnings:
./drivers/pinctrl/pinctrl-rockchip.c:3221:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 3196, but without a corresponding object release within this function.
./drivers/pinctrl/pinctrl-rockchip.c:3223:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 3196, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: linux-gpio@vger.kernel.org
Cc: linux-rockchip@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>