Xin Long says:

====================
net: support SCTP CRC csum offload for tunneling packets in some drivers

This patchset introduces inline function skb_csum_is_sctp(), and uses it
to validate it's a sctp CRC csum offload packet, to make SCTP CRC csum
offload for tunneling packets supported in some HW drivers.
====================

Link: https://lore.kernel.org/r/cover.1610777159.git.lucien.xin@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Using skb_csum_is_sctp is a easier way to validate it's a SCTP CRC
checksum offload packet, and yet it also makes ixgbevf support SCTP
CRC checksum offload for UDP and GRE encapped packets, just as it
does in igb driver.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Using skb_csum_is_sctp is a easier way to validate it's a SCTP CRC
checksum offload packet, and yet it also makes ixgbe support SCTP
CRC checksum offload for UDP and GRE encapped packets, just as it
does in igb driver.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Using skb_csum_is_sctp is a easier way to validate it's a SCTP CRC
checksum offload packet, and yet it also makes igc support SCTP
CRC checksum offload for UDP and GRE encapped packets, just as it
does in igb driver.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Using skb_csum_is_sctp is a easier way to validate it's a SCTP CRC
checksum offload packet, and yet it also makes igbvf support SCTP
CRC checksum offload for UDP and GRE encapped packets, just as it
does in igb driver.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Using skb_csum_is_sctp is a easier way to validate it's a SCTP
CRC checksum offload packet, and there is no need to parse the
packet to check its proto field, especially when it's a UDP or
GRE encapped packet.

So this patch also makes igb support SCTP CRC checksum offload
for UDP and GRE encapped packets.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

This patch is to define a inline function skb_csum_is_sctp(), and
also replace all places where it checks if it's a SCTP CSUM skb.
This function would be used later in many networking drivers in
the following patches.
Suggested-by: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

container_of() macro hides a local variable '__mptr' inside. This
becomes a problem when several container_of() are nested in each
other within single line or plain macros.
As C preprocessor doesn't support generating random variable names,
the sole solution is to avoid defining macros that consist only of
container_of() calls, or they will self-shadow '__mptr' each time:

In file included from ./include/linux/bitmap.h:10,
                 from drivers/net/phy/phy_device.c:12:
drivers/net/phy/phy_device.c: In function ‘phy_device_release’:
./include/linux/kernel.h:693:8: warning: declaration of ‘__mptr’ shadows a previous local [-Wshadow]
  693 |  void *__mptr = (void *)(ptr);     \
      |        ^~~~~~
./include/linux/phy.h:647:26: note: in expansion of macro ‘container_of’
  647 | #define to_phy_device(d) container_of(to_mdio_device(d), \
      |                          ^~~~~~~~~~~~
./include/linux/mdio.h:52:27: note: in expansion of macro ‘container_of’
   52 | #define to_mdio_device(d) container_of(d, struct mdio_device, dev)
      |                           ^~~~~~~~~~~~
./include/linux/phy.h:647:39: note: in expansion of macro ‘to_mdio_device’
  647 | #define to_phy_device(d) container_of(to_mdio_device(d), \
      |                                       ^~~~~~~~~~~~~~
drivers/net/phy/phy_device.c:217:8: note: in expansion of macro ‘to_phy_device’
  217 |  kfree(to_phy_device(dev));
      |        ^~~~~~~~~~~~~
./include/linux/kernel.h:693:8: note: shadowed declaration is here
  693 |  void *__mptr = (void *)(ptr);     \
      |        ^~~~~~
./include/linux/phy.h:647:26: note: in expansion of macro ‘container_of’
  647 | #define to_phy_device(d) container_of(to_mdio_device(d), \
      |                          ^~~~~~~~~~~~
drivers/net/phy/phy_device.c:217:8: note: in expansion of macro ‘to_phy_device’
  217 |  kfree(to_phy_device(dev));
      |        ^~~~~~~~~~~~~

As they are declared in header files, these warnings are highly
repetitive and very annoying (along with the one from linux/pci.h).

Convert the related macros from linux/{mdio,phy}.h to static inlines
to avoid self-shadowing and potentially improve bug-catching.
No functional changes implied.
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20210116161246.67075-1-alobakin@pm.meSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Currently the driver doesn't drop a packet which can't be sent by tun
(e.g bad packet). In this case, the driver will always process the
same packet lead to the tx queue stuck.

To fix this issue:
1. in the case of persistent failure (e.g bad packet), the driver
   can skip this descriptor by ignoring the error.
2. in the case of transient failure (e.g -ENOBUFS, -EAGAIN and -ENOMEM),
   the driver schedules the worker to try again.
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Link: https://lore.kernel.org/r/1610685980-38608-1-git-send-email-wangyunjian@huawei.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

When DEBUG is defined this error occurs

drivers/net/ethernet/hisilicon/hns/hns_enet.c:1505:36: error:
  ‘struct net_device’ has no member named ‘ae_handle’;
  did you mean ‘rx_handler’?
  assert(skb->queue_mapping < ndev->ae_handle->q_num);
                                    ^~~~~~~~~

ae_handle is an element of struct hns_nic_priv, so change
ndev to priv.
Signed-off-by: Tom Rix <trix@redhat.com>
Link: https://lore.kernel.org/r/20210117191044.533725-1-trix@redhat.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

When DEBUG is defined this error occurs

drivers/net/arcnet/com20020_cs.c:70:15: error: ‘com20020_REG_W_ADDR_HI’
  undeclared (first use in this function);
  did you mean ‘COM20020_REG_W_ADDR_HI’?
       ioaddr, com20020_REG_W_ADDR_HI);
               ^~~~~~~~~~~~~~~~~~~~~~

From reviewing the context, the suggestion is what is meant.
Signed-off-by: Tom Rix <trix@redhat.com>
Acked-by: Joe Perches <joe@perches.com>
Link: https://lore.kernel.org/r/20210117181519.527625-1-trix@redhat.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Tariq Toukan says:

====================
TLS device offload for Bond

This series opens TX and RX TLS device offload for bond interfaces.
This allows bond interfaces to benefit from capable lower devices.

We add a new ndo_sk_get_lower_dev() to be used to get the lower dev that
corresponds to a given socket.
The TLS module uses it to interact directly with the lowest device in
chain, and invoke the control operations in tlsdev_ops. This means that the
bond interface doesn't have his own struct tlsdev_ops instance and
derived logic/callbacks.

To keep simple track of the HW and SW TLS contexts, we bind each socket to
a specific lower device for the socket's whole lifetime. This is logically
valid (and similar to the SW kTLS behavior) in the following bond configuration,
so we restrict the offload support to it:

((mode == balance-xor) or (mode == 802.3ad))
and xmit_hash_policy == layer3+4.

In this design, TLS TX/RX offload feature flags of the bond device are
independent from the lower devices. They reflect the current features state,
but are not directly controllable.
This is because the bond driver is bypassed by the call to
ndo_sk_get_lower_dev(), without him knowing who the caller is.
The bond TLS feature flags are set/cleared only according to the configuration
of the mode and xmit_hash_policy.

Bypass is true only for the control flow. Packets in fast path still go through
the bond logic.

The design here differs from the xfrm/ipsec offload, where the bond driver
has his own copy of struct xfrmdev_ops and callbacks.
====================

Link: https://lore.kernel.org/r/20210117145949.8632-1-tariqt@nvidia.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

In the tls_dev_event handler, ignore tlsdev_ops requirement for bond
interfaces, they do not exist as the interaction is done directly with
the lower device.

Also, make the validate function pass when it's called with the upper
bond interface.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Boris Pismenny <borisp@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Do not call the tls_dev_ops of upper devices. Instead, ask them
for the proper lowest device and communicate with it directly.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Boris Pismenny <borisp@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Following the description in previous patch (for TX):
As the bond interface is being bypassed by the TLS module, interacting
directly against the lower devs, there is no way for the bond interface
to disable its device offload capabilities, as long as the mode/policy
config allows it.
Hence, the feature flag is not directly controllable, but just reflects
the offload status based on the logic under bond_sk_check().

Here we just declare RX device offload support, and expose it via the
NETIF_F_HW_TLS_RX flag.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Boris Pismenny <borisp@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Implement TLS TX device offload for bonding interfaces.
This allows kTLS sockets running on a bond to benefit from the
device offload on capable lower devices.

To allow a simple and fast maintenance of the TLS context in SW and
lower devices, we bind the TLS socket to a specific lower dev.
To achieve a behavior similar to SW kTLS, we support only balance-xor
and 802.3ad modes, with xmit_hash_policy=layer3+4. This is enforced
in bond_sk_check(), done in a previous patch.

For the above configuration, the SW implementation keeps picking the
same exact lower dev for all the socket's SKBs. The device offload
behaves similarly, making the decision once at the connection creation.

Per socket, the TLS module should work directly with the lowest netdev
in chain, to call the tls_dev_ops operations.

As the bond interface is being bypassed by the TLS module, interacting
directly against the lower devs, there is no way for the bond interface
to disable its device offload capabilities, as long as the mode/policy
config allows it.
Hence, the feature flag is not directly controllable, but just reflects
the current offload status based on the logic under bond_sk_check().
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Boris Pismenny <borisp@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In preparation for more cases that call netdev_update_features().

While here, move the features logic to the stage where struct bond
is already updated, and pass it as the only parameter to function
bond_set_xfrm_features().
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Boris Pismenny <borisp@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Add ndo_sk_get_lower_dev() implementation for bond interfaces.

Support only for the cases where the socket's and SKBs' hash
yields identical value for the whole connection lifetime.

Here we restrict it to L3+4 sockets only, with
xmit_hash_policy==LAYER34 and bond modes xor/802.3ad.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Boris Pismenny <borisp@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Hash logic on L3 will be used in a downstream patch for one more use
case.
Take it to a function for a better code reuse.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Boris Pismenny <borisp@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

ndo_sk_get_lower_dev returns the lower netdev that corresponds to
a given socket.
Additionally, we implement a helper netdev_sk_get_lowest_dev() to get
the lowest one in chain.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Boris Pismenny <borisp@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The wrappers in include/linux/pci-dma-compat.h should go away.

The patch has been generated with the coccinelle script below and has been
hand modified to replace GFP_ with a correct flag.
It has been compile tested.

When memory is allocated in 'ql_alloc_net_req_rsp_queues()' GFP_KERNEL can
be used because it is only called from 'ql_alloc_mem_resources()' which
already calls 'ql_alloc_buffer_queues()' which uses GFP_KERNEL. (see below)

When memory is allocated in 'ql_alloc_buffer_queues()' GFP_KERNEL can be
used because this flag is already used just a few line above.

When memory is allocated in 'ql_alloc_small_buffers()' GFP_KERNEL can
be used because it is only called from 'ql_alloc_mem_resources()' which
already calls 'ql_alloc_buffer_queues()' which uses GFP_KERNEL. (see above)

When memory is allocated in 'ql_alloc_mem_resources()' GFP_KERNEL can be
used because this function already calls 'ql_alloc_buffer_queues()' which
uses GFP_KERNEL. (see above)

While at it, use 'dma_set_mask_and_coherent()' instead of 'dma_set_mask()/
dma_set_coherent_mask()' in order to slightly simplify code.

@@
@@
-    PCI_DMA_BIDIRECTIONAL
+    DMA_BIDIRECTIONAL

@@
@@
-    PCI_DMA_TODEVICE
+    DMA_TO_DEVICE

@@
@@
-    PCI_DMA_FROMDEVICE
+    DMA_FROM_DEVICE

@@
@@
-    PCI_DMA_NONE
+    DMA_NONE

@@
expression e1, e2, e3;
@@
-    pci_alloc_consistent(e1, e2, e3)
+    dma_alloc_coherent(&e1->dev, e2, e3, GFP_)

@@
expression e1, e2, e3;
@@
-    pci_zalloc_consistent(e1, e2, e3)
+    dma_alloc_coherent(&e1->dev, e2, e3, GFP_)

@@
expression e1, e2, e3, e4;
@@
-    pci_free_consistent(e1, e2, e3, e4)
+    dma_free_coherent(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_map_single(e1, e2, e3, e4)
+    dma_map_single(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_unmap_single(e1, e2, e3, e4)
+    dma_unmap_single(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4, e5;
@@
-    pci_map_page(e1, e2, e3, e4, e5)
+    dma_map_page(&e1->dev, e2, e3, e4, e5)

@@
expression e1, e2, e3, e4;
@@
-    pci_unmap_page(e1, e2, e3, e4)
+    dma_unmap_page(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_map_sg(e1, e2, e3, e4)
+    dma_map_sg(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_unmap_sg(e1, e2, e3, e4)
+    dma_unmap_sg(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_dma_sync_single_for_cpu(e1, e2, e3, e4)
+    dma_sync_single_for_cpu(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_dma_sync_single_for_device(e1, e2, e3, e4)
+    dma_sync_single_for_device(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_dma_sync_sg_for_cpu(e1, e2, e3, e4)
+    dma_sync_sg_for_cpu(&e1->dev, e2, e3, e4)

@@
expression e1, e2, e3, e4;
@@
-    pci_dma_sync_sg_for_device(e1, e2, e3, e4)
+    dma_sync_sg_for_device(&e1->dev, e2, e3, e4)

@@
expression e1, e2;
@@
-    pci_dma_mapping_error(e1, e2)
+    dma_mapping_error(&e1->dev, e2)

@@
expression e1, e2;
@@
-    pci_set_dma_mask(e1, e2)
+    dma_set_mask(&e1->dev, e2)

@@
expression e1, e2;
@@
-    pci_set_consistent_dma_mask(e1, e2)
+    dma_set_coherent_mask(&e1->dev, e2)
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/20210117081542.560021-1-christophe.jaillet@wanadoo.frSigned-off-by: Jakub Kicinski <kuba@kernel.org>

tcf_action_init_1() loads tc action modules automatically with
request_module() after parsing the tc action names, and it drops RTNL
lock and re-holds it before and after request_module(). This causes a
lot of troubles, as discovered by syzbot, because we can be in the
middle of batch initializations when we create an array of tc actions.

One of the problem is deadlock:

CPU 0					CPU 1
rtnl_lock();
for (...) {
  tcf_action_init_1();
    -> rtnl_unlock();
    -> request_module();
				rtnl_lock();
				for (...) {
				  tcf_action_init_1();
				    -> tcf_idr_check_alloc();
				   // Insert one action into idr,
				   // but it is not committed until
				   // tcf_idr_insert_many(), then drop
				   // the RTNL lock in the _next_
				   // iteration
				   -> rtnl_unlock();
    -> rtnl_lock();
    -> a_o->init();
      -> tcf_idr_check_alloc();
      // Now waiting for the same index
      // to be committed
				    -> request_module();
				    -> rtnl_lock()
				    // Now waiting for RTNL lock
				}
				rtnl_unlock();
}
rtnl_unlock();

This is not easy to solve, we can move the request_module() before
this loop and pre-load all the modules we need for this netlink
message and then do the rest initializations. So the loop breaks down
to two now:

        for (i = 1; i <= TCA_ACT_MAX_PRIO && tb[i]; i++) {
                struct tc_action_ops *a_o;

                a_o = tc_action_load_ops(name, tb[i]...);
                ops[i - 1] = a_o;
        }

        for (i = 1; i <= TCA_ACT_MAX_PRIO && tb[i]; i++) {
                act = tcf_action_init_1(ops[i - 1]...);
        }

Although this looks serious, it only has been reported by syzbot, so it
seems hard to trigger this by humans. And given the size of this patch,
I'd suggest to make it to net-next and not to backport to stable.

This patch has been tested by syzbot and tested with tdc.py by me.

Fixes: 0fedc63f ("net_sched: commit action insertions together")
Reported-and-tested-by: syzbot+82752bc5331601cf4899@syzkaller.appspotmail.com
Reported-and-tested-by: syzbot+b3b63b6bff456bd95294@syzkaller.appspotmail.com
Reported-by: syzbot+ba67b12b1ca729912834@syzkaller.appspotmail.com
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <cong.wang@bytedance.com>
Tested-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Link: https://lore.kernel.org/r/20210117005657.14810-1-xiyou.wangcong@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Defining DEBUG should only be done in development.
So remove DEBUG.
Signed-off-by: Tom Rix <trix@redhat.com>
Link: https://lore.kernel.org/r/20210115235346.289611-1-trix@redhat.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Xin Long says:

====================
net: make udp tunnel devices support fraglist

Like GRE device, UDP tunnel devices should also support fraglist, so
that some protocol (like SCTP) HW GSO that requires NETIF_F_FRAGLIST
in the dev can work. Especially when the lower device support both
NETIF_F_GSO_UDP_TUNNEL and NETIF_F_GSO_SCTP.
====================

Link: https://lore.kernel.org/r/cover.1610704037.git.lucien.xin@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Like vxlan and geneve, bareudp also needs this dev feature
to support some protocol's HW GSO.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Some protocol HW GSO requires fraglist supported by the device, like
SCTP. Without NETIF_F_FRAGLIST set in the dev features of geneve, it
would have to do SW GSO before the packets enter the driver, even
when the geneve dev and lower dev (like veth) both have the feature
of NETIF_F_GSO_SCTP.

So this patch is to add it for geneve.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Some protocol HW GSO requires fraglist supported by the device, like
SCTP. Without NETIF_F_FRAGLIST set in the dev features of vxlan, it
would have to do SW GSO before the packets enter the driver, even
when the vxlan dev and lower dev (like veth) both have the feature
of NETIF_F_GSO_SCTP.

So this patch is to add it for vxlan.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

For additional robustness in the face of Hyper-V errors or malicious
behavior, validate all values that originate from packets that Hyper-V
has sent to the guest.  Ensure that invalid values cannot cause indexing
off the end of an array, or subvert an existing validation via integer
overflow.  Ensure that outgoing packets do not have any leftover guest
memory that has not been zeroed out.
Reported-by: Juan Vazquez <juvazq@microsoft.com>
Signed-off-by: Andrea Parri (Microsoft) <parri.andrea@gmail.com>
Link: https://lore.kernel.org/r/20210114202628.119541-1-parri.andrea@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Replace some checks for ETH_P_8021Q and ETH_P_8021AD with
eth_type_vlan().
Signed-off-by: Menglong Dong <dong.menglong@zte.com.cn>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Link: https://lore.kernel.org/r/20210117080950.122761-1-dong.menglong@zte.com.cnSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Alex Elder says:

====================
net: ipa: interconnect improvements

The main outcome of this series is to allow the number of
interconnects used by the IPA to differ from the three that
are implemented now.  With this series in place, any number
of interconnects can now be used, all specified in the
configuration data for a specific platform.

A few minor interconnect-related cleanups are implemented as well.
====================

Link: https://lore.kernel.org/r/20210115125050.20555-1-elder@linaro.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Currently we assume that the IPA hardware has exactly three
interconnects.  But that won't be guaranteed for all platforms,
so allow any number of interconnects to be specified in the
configuration data.

For each platform, define an array of interconnect data entries
(still associated with the IPA clock structure), and record the
number of entries initialized in that array.

Loop over all entries in this array when initializing, enabling,
disabling, or tearing down the set of interconnects.

With this change we no longer need the ipa_interconnect_id
enumerated type, so get rid of it.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Pass an the address of an IPA interconnect structure and its
configuration data to ipa_interconnect_init_one() and have that
function initialize all the structure's fields.  Change the function
to simply return an error code.

Introduce ipa_interconnect_exit_one() to encapsulate the cleanup of
an IPA interconnect structure.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Add the name to the configuration data for each interconnect.  Use
this information rather than a constant string during initialization.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Add fields in the ipa_interconnect structure to hold the average and
peak bandwidth values for the interconnect.  Pass the configuring
data for interconnects to ipa_interconnect_init() so these values
can be recorded, and use them when enabling the interconnects.

There's no longer any need to keep a copy of the interconnect data
after initialization.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Rather than having separate pointers for the memory, imem, and
config interconnect paths, maintain an array of ipa_interconnect
structures each of which contains a pointer to a path.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

If disabling interconnects fails there's not a lot we can do.  The
only two callers of ipa_interconnect_disable() ignore the return
value, so just give the function a void return type.

Print an error message if disabling any of the interconnects is not
successful.  Return (and print) only the first error seen.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Use "bandwidth" rather than "rate" in describing the average and
peak values to use for IPA interconnects.  They should have been
named that way to begin with.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Xin Long says:

====================
net: fix the features flag in sctp_gso_segment

Patch 1/2 is to improve the code in skb_segment(), and it is needed
by Patch 2/2.
====================

Link: https://lore.kernel.org/r/cover.1610703289.git.lucien.xin@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

It makes more sense to clear NETIF_F_SG instead of set it when
calling skb_segment() in sctp_gso_segment(), since SCTP GSO is
using head_skb's fraglist, of which all frags are linear skbs.

This will make SCTP GSO code more understandable.
Suggested-by: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

After commit 89319d38 ("net: Add frag_list support to skb_segment"),
it goes to process frag_list when !hsize in skb_segment(). However, when
using skb frag_list, sg normally should not be set. In this case, hsize
will be set with len right before !hsize check, then it won't go to
frag_list processing code.

So the right thing to do is move the hsize check to the else block, so
that it won't affect the !hsize check for frag_list processing.

v1->v2:
  - change to do "hsize <= 0" check instead of "!hsize", and also move
    "hsize < 0" into else block, to save some cycles, as Alex suggested.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>