1. 28 May, 2019 8 commits
  2. 27 May, 2019 5 commits
    • Kalle Valo's avatar
      Merge ath-next from git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/ath.git · 889ca180
      Kalle Valo authored
      ath.git patches for 5.3. Major changes:
      
      ath10k
      
      * enable SDIO support, first one being QCA6174 hw3.2
      889ca180
    • YueHaibing's avatar
      cxgb4: Make t4_get_tp_e2c_map static · f4aa8012
      YueHaibing authored
      Fix sparse warning:
      
      drivers/net/ethernet/chelsio/cxgb4/t4_hw.c:6216:14:
       warning: symbol 't4_get_tp_e2c_map' was not declared. Should it be static?
      Reported-by: default avatarHulk Robot <hulkci@huawei.com>
      Signed-off-by: default avatarYueHaibing <yuehaibing@huawei.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      f4aa8012
    • David Ahern's avatar
      selftest: Fixes for icmp_redirect test · 99513cfa
      David Ahern authored
      I was really surprised that the IPv6 mtu exception followed by redirect
      test was passing as nothing about the code suggests it should. The problem
      is actually with the logic in the test script.
      
      Fix the test cases as follows:
      1. add debug function to dump the initial and redirect gateway addresses
         for ipv6. This is shown only in verbose mode. It helps verify the
         output of 'route get'.
      
      2. fix the check_exception logic for the reset case to make sure that
         for IPv4 neither mtu nor redirect appears in the 'route get' output.
         For IPv6, make sure mtu is not present and the gateway is the initial
         R1 lladdr.
      
      3. fix the reset logic by using a function to delete the routes added by
         initial_route_*. This format works better for the nexthop version of
         the tests.
      
      While improving the test cases, go ahead and ensure that forwarding is
      disabled since IPv6 redirect requires it.
      
      Also, runs with kernel debugging enabled sometimes show a failure with
      one of the ipv4 tests, so spread the pings over longer time interval.
      
      The end result is that 2 tests now show failures:
      
      TEST: IPv6: mtu exception plus redirect                    [FAIL]
      
      and the VRF version.
      
      This is a bug in the IPv6 logic that will need to be fixed
      separately. Redirect followed by MTU works because __ip6_rt_update_pmtu
      hits the 'if (!rt6_cache_allowed_for_pmtu(rt6))' path and updates the
      mtu on the exception rt6_info.
      
      MTU followed by redirect does not have this logic. rt6_do_redirect
      creates a new exception and then rt6_insert_exception removes the old
      one which has the MTU exception.
      
      Fixes: ec810535 ("selftests: Add redirect tests")
      Signed-off-by: default avatarDavid Ahern <dsahern@gmail.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      99513cfa
    • Colin Ian King's avatar
      ipv4: remove redundant assignment to n · df801522
      Colin Ian King authored
      The pointer n is being assigned a value however this value is
      never read in the code block and the end of the code block
      continues to the next loop iteration. Clean up the code by
      removing the redundant assignment.
      
      Fixes: 1bff1a0c ("ipv4: Add function to send route updates")
      Addresses-Coverity: ("Unused value")
      Signed-off-by: default avatarColin Ian King <colin.king@canonical.com>
      Reviewed-by: default avatarDavid Ahern <dsahern@gmail.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      df801522
    • Heiner Kallweit's avatar
      net: phy: bcm87xx: improve bcm87xx_config_init and feature detection · 476cc6c9
      Heiner Kallweit authored
      PHY drivers don't have to and shouldn't fiddle with phylib internals.
      Most of the code in bcm87xx_config_init() can be removed because
      phylib takes care.
      
      In addition I replaced usage of PHY_10GBIT_FEC_FEATURES with an
      implementation of the get_features callback. PHY_10GBIT_FEC_FEATURES
      is used by this driver only and it's questionable whether there
      will be any other PHY supporting this mode only. Having said that
      in one of the next kernel versions we may decide to remove it.
      Signed-off-by: default avatarHeiner Kallweit <hkallweit1@gmail.com>
      Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
      476cc6c9
  3. 26 May, 2019 27 commits