update RF register 47 and 54 values according to vendor driver
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Use register values from init LNA function instead of the ones from
restore LNA function. Apply register values based on rx path
configuration.
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Somehow AP doesn't come up and the first scan fails if we don't do
VCO calibration every time.
The vendor driver duplicates the VCO calibration function into the
channel switching logic, we can do the same with less duplication.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The base value used for MT7620 differs from Rt5392 which resulted in
quite bad RX signal quality. Fix this by using the correct base value as
well as the LNA calibration values for HT20.
Reported-by: Tom Psyborg <pozega.tomislav@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

ath.git patches for 4.12. Major changes:

ath9k

* add support for Dell Wireless 1601 PCI device

* add debugfs file to manually override noise floor

ath10k

* bump up FW API to 6 for a new QCA6174 firmware branch

wil6210

* support 8 kB RX buffers

Merge tag 'iwlwifi-next-for-kalle-2017-04-19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next

Another series of patches intended for v4.12.  These are the changes:

 * Heavy work for the A000 device series;
 * Some cleanup patches;
 * A few fixes;
 * Dynamic SAR support;
 * Geographical SAR support;
 * Support a few new PCI device IDs;

When wifi is under scanning/linking/roaming, do not run the reset of the
coex mechanism because these activities are important for wifi, just run
the linking process and return.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

If wifi is in power saving mode, do nothing.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
  ---
 drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8821a2ant.c | 6 ++++++
 1 file changed, 6 insertions(+)
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

For bt profiling, we do not need to limit the rx agg size.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Using macro to control the bt threshold.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Check the bt rssi first and decrease it if the bt rssi is too high.
Then set the tdma and coex table.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Use h2c to tell the firmware if the number of AP is more than 10 or
not.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Here we monitor one more wifi rssi to check the status of the network
and set the coex table instead of the legacy way.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

For p2p/miracast, the wifi may have multiple ports for different roles.
Under this, we need extra settings for turning off the tdma and proper
coex table parameters.

We monnitor the number of links on a port to determine if it is for
p2p/miracast or not.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Monitor the rssi state to set the tdma and limit rx aggregation size to
fit the bt profiling.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Fix some ident and naming for linux coding style.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

For bt a2dp, we need to check more rssi state combinations to have
better voice quality.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Let the wifi use main antenna to have higher power.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The threshold is used to adjust the base line for the rssi state.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Use software dac swing and double check if it is sco_only to set the
tdma for voice quality.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

1. Add more cases to adjust the wifi duration and add a case with
the max interval of 3 for some future uses.

2. rename tdma_adj -> ps_tdma_du_adj to indicate that this member is
for power saving tdma duration adjustment
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The dac swing level should be an unsigned 32-bit value rather than
boolean.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Depending on the state of wifi, we need to set different tdma and coex
table parameters to make wfi and bt coexist smoothly. Otherwise the
bt may have low sound quality or mouse lag, which mean bad user
experience. The same problem may occur on wifi also, if could disconnect
or lose some important packets.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

If the wifi or bt has low rssi, they need extra parameter settings for
the tdma.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Tune the wifi/bt slot time to get better performance.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Register 0xcb4 determines if the PTA circuit can control the swtich
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Instead of just setting the coex table directly, we check if the
wifi is under some important activity (scanning|roaming|linking) and
mark the packets as high priority in that case.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

When wifi is at 5G band, it does not intefere with 2.4G bt signal,
hence we can just ignore it and transmit normally as nothing happened.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Monitor wifi status and check if it is changed.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Gather multiple coex table settings into a function coex_table_with_type()
and control the coex table according the type value as put in
switch-case expression.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Remove workaround for HT40 issues for RF low pass filter.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The power_save_state function checks the state of power saving.
For tdma settings, the wifi sends nullfunc to pretend enter power saving
and then bt can transmit. Hence the coex needs to check the power status
before set the pstdma function.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Change h2c parameter to decrease tx penalty.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Gather variables to the 8821a2ant coex structure.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Originally we only increase/decrease bt power in a fixed power gap, this
patch makes us be able to modify bt power for multiple power gaps and we
can precisely adjust the bt power.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This function updates the information of bt profiling to help us decide
the network status and dispatch the resource properly.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

If there are a lot of low-rate packets, then the connection of wifi is
unstable. If so, we should switch resource to bt to have a higher
transmission quality, or wifi resource will be wasted
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

We monitor the packet counter to guess if the bt is slave or not, and
when bt is slave, it may receive packet at any time, so we will have to
take care about it
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Larger packets have higher opportunity to be interrupt by bt signal.
In order to shorten the transmission time, control the packet
aggregation size.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pkshih <pkshih@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

His email is bouncing, and he'd like to use this new one.

Cc: Amitkumar Karwar <amitkarwar@gmail.com>
Cc: Nishant Sarmukadam <nishants@marvell.com>
Cc: Ganapathi Bhat <gbhat@marvell.com>
Cc: Xinming Hu <huxm@marvell.com>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>