Add support for inner meta matching on:

- NFT_META_PROTOCOL: to match on the ethertype, this can be used
  regardless tunnel protocol provides no link layer header, in that case
  nft_inner sets on the ethertype based on the IP header version field.
- NFT_META_L4PROTO: to match on the layer 4 protocol.

These meta expression are usually autogenerated as dependencies by
userspace nftables.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Add NFT_PKTINFO_INNER_FULL flag to annotate that inner offsets are
available. Store nft_inner_tun_ctx object in percpu area to cache
existing inner offsets for this skbuff.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

This new expression allows you to match on the inner headers that are
encapsulated by any of the existing tunneling protocols.

This expression parses the inner packet to set the link, network and
transport offsets, so the existing expressions (with a few updates) can
be reused to match on the inner headers.

The inner expression supports for different tunnel combinations such as:

- ethernet frame over IPv4/IPv6 packet, eg. VxLAN.
- IPv4/IPv6 packet over IPv4/IPv6 packet, eg. IPIP.
- IPv4/IPv6 packet over IPv4/IPv6 + transport header, eg. GRE.
- transport header (ESP or SCTP) over transport header (usually UDP)

The following fields are used to describe the tunnel protocol:

- flags, which describe how to parse the inner headers:

  NFT_PAYLOAD_CTX_INNER_TUN, the tunnel provides its own header.
  NFT_PAYLOAD_CTX_INNER_ETHER, the ethernet frame is available as inner header.
  NFT_PAYLOAD_CTX_INNER_NH, the network header is available as inner header.
  NFT_PAYLOAD_CTX_INNER_TH, the transport header is available as inner header.

For example, VxLAN sets on all of these flags. While GRE only sets on
NFT_PAYLOAD_CTX_INNER_NH and NFT_PAYLOAD_CTX_INNER_TH. Then, ESP over
UDP only sets on NFT_PAYLOAD_CTX_INNER_TH.

The tunnel description is composed of the following attributes:

- header size: in case the tunnel comes with its own header, eg. VxLAN.

- type: this provides a hint to userspace on how to delinearize the rule.
  This is useful for VxLAN and Geneve since they run over UDP, since
  transport does not provide a hint. This is also useful in case hardware
  offload is ever supported. The type is not currently interpreted by the
  kernel.

- expression: currently only payload supported. Follow up patch adds
  also inner meta support which is required by autogenerated
  dependencies. The exthdr expression should be supported too
  at some point. There is a new inner_ops operation that needs to be
  set on to allow to use an existing expression from the inner expression.

This patch adds a new NFT_PAYLOAD_TUN_HEADER base which allows to match
on the tunnel header fields, eg. vxlan vni.

The payload expression is embedded into nft_inner private area and this
private data area is passed to the payload inner eval function via
direct call.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

ipip is an special case, transport and inner header offset are set to
the same offset to use the upcoming inner expression for matching on
inner tunnel headers.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Parse GRE v0 packets to properly set up inner offset, this allow for
matching on inner headers.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

nft_objref is needed to reference named objects, it makes
no sense to disable it.

Before:
   text	   data	    bss	    dec	 filename
  4014	    424	      0	   4438	 nft_objref.o
  4174	   1128	      0	   5302	 nft_objref.ko
359351	  15276	    864	 375491	 nf_tables.ko
After:
  text	   data	    bss	    dec	 filename
  3815	    408	      0	   4223	 nft_objref.o
363161	  15692	    864	 379717	 nf_tables.ko
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

structure is reduced from 32 to 24 bytes.  While at it, also check
that iphdrlen is sane, this is guaranteed for NFPROTO_IPV4 but not
for ingress or bridge, so add checks for this.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Not required to expose this header in nf_tables_core.h, move it to where
it is used, ie. nft_payload.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Round up allocations with kmalloc_size_roundup() so that build_skb()'s
use of ksize() is always accurate and no special handling of the memory
is needed by KASAN, UBSAN_BOUNDS, nor FORTIFY_SOURCE.

Cc: Rasesh Mody <rmody@marvell.com>
Cc: GR-Linux-NIC-Dev@marvell.com
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20221022021004.gonna.489-kees@kernel.orgSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Mat Martineau says:

====================
mptcp: Socket option updates

Patches 1 and 3 refactor a recent socket option helper function for more
generic use, and make use of it in a couple of places.

Patch 2 adds TCP_FASTOPEN_NO_COOKIE functionality to MPTCP sockets,
similar to TCP_FASTOPEN_CONNECT support recently added in v6.1
====================

Link: https://lore.kernel.org/r/20221022004505.160988-1-mathew.j.martineau@linux.intel.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

mptcp_setsockopt_sol_tcp_defer() was doing the same thing as
mptcp_setsockopt_first_sf_only() except for the returned code in case of
error.

Ignoring the error is needed to mimic how TCP_DEFER_ACCEPT is handled
when used with "plain" TCP sockets.

The specific function for TCP_DEFER_ACCEPT can be replaced by the new
mptcp_setsockopt_first_sf_only() helper and errors can be ignored to
stay compatible with TCP. A bit of cleanup.
Suggested-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

The goal of this socket option is to configure MPTCP + TFO without
cookie per socket.

It was already possible to enable TFO without a cookie per netns by
setting net.ipv4.tcp_fastopen sysctl knob to the right value. Per route
was also supported by setting 'fastopen_no_cookie' option. This patch
adds a per socket support like it is possible to do with TCP thanks to
TCP_FASTOPEN_NO_COOKIE socket option.

The only thing to do here is to relay the request to the first subflow
like it is already done for TCP_FASTOPEN_CONNECT.
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

There are other socket options that need to act only on the first
subflow, e.g. all TCP_FASTOPEN* socket options.

This is similar to the getsockopt version.

In the next commit, this new mptcp_setsockopt_first_sf_only() helper is
used by other another option.
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Kuniyuki Iwashima says:

====================
soreuseport: Fix broken SO_INCOMING_CPU.

setsockopt(SO_INCOMING_CPU) for UDP/TCP is broken since 4.5/4.6 due to
these commits:

  * e32ea7e7 ("soreuseport: fast reuseport UDP socket selection")
  * c125e80b ("soreuseport: fast reuseport TCP socket selection")

These commits introduced the O(1) socket selection algorithm and removed
O(n) iteration over the list, but it ignores the score calculated by
compute_score().  As a result, it caused two misbehaviours:

  * Unconnected sockets receive packets sent to connected sockets
  * SO_INCOMING_CPU does not work

The former is fixed by commit acdcecc6 ("udp: correct reuseport
selection with connected sockets").  This series fixes the latter and
adds some tests for SO_INCOMING_CPU.
====================

Link: https://lore.kernel.org/r/20221021204435.4259-1-kuniyu@amazon.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Some highly optimised applications use SO_INCOMING_CPU to make them
efficient, but they didn't test if it's working correctly by getsockopt()
to avoid slowing down.  As a result, no one noticed it had been broken
for years, so it's a good time to add a test to catch future regression.

The test does

  1) Create $(nproc) TCP listeners associated with each CPU.

  2) Create 32 child sockets for each listener by calling
     sched_setaffinity() for each CPU.

  3) Check if accept()ed sockets' sk_incoming_cpu matches
     listener's one.

If we see -EAGAIN, SO_INCOMING_CPU is broken.  However, we might not see
any error even if broken; the kernel could miraculously distribute all SYN
to correct listeners.  Not to let that happen, we must increase the number
of clients and CPUs to some extent, so the test requires $(nproc) >= 2 and
creates 64 sockets at least.

Test:
  $ nproc
  96
  $ ./so_incoming_cpu

Before the previous patch:

  # Starting 12 tests from 5 test cases.
  #  RUN           so_incoming_cpu.before_reuseport.test1 ...
  # so_incoming_cpu.c:191:test1:Expected cpu (5) == i (0)
  # test1: Test terminated by assertion
  #          FAIL  so_incoming_cpu.before_reuseport.test1
  not ok 1 so_incoming_cpu.before_reuseport.test1
  ...
  # FAILED: 0 / 12 tests passed.
  # Totals: pass:0 fail:12 xfail:0 xpass:0 skip:0 error:0

After:

  # Starting 12 tests from 5 test cases.
  #  RUN           so_incoming_cpu.before_reuseport.test1 ...
  # so_incoming_cpu.c:199:test1:SO_INCOMING_CPU is very likely to be working correctly with 3072 sockets.
  #            OK  so_incoming_cpu.before_reuseport.test1
  ok 1 so_incoming_cpu.before_reuseport.test1
  ...
  # PASSED: 12 / 12 tests passed.
  # Totals: pass:12 fail:0 xfail:0 xpass:0 skip:0 error:0
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Kazuho Oku reported that setsockopt(SO_INCOMING_CPU) does not work
with setsockopt(SO_REUSEPORT) since v4.6.

With the combination of SO_REUSEPORT and SO_INCOMING_CPU, we could
build a highly efficient server application.

setsockopt(SO_INCOMING_CPU) associates a CPU with a TCP listener
or UDP socket, and then incoming packets processed on the CPU will
likely be distributed to the socket.  Technically, a socket could
even receive packets handled on another CPU if no sockets in the
reuseport group have the same CPU receiving the flow.

The logic exists in compute_score() so that a socket will get a higher
score if it has the same CPU with the flow.  However, the score gets
ignored after the blamed two commits, which introduced a faster socket
selection algorithm for SO_REUSEPORT.

This patch introduces a counter of sockets with SO_INCOMING_CPU in
a reuseport group to check if we should iterate all sockets to find
a proper one.  We increment the counter when

  * calling listen() if the socket has SO_INCOMING_CPU and SO_REUSEPORT

  * enabling SO_INCOMING_CPU if the socket is in a reuseport group

Also, we decrement it when

  * detaching a socket out of the group to apply SO_INCOMING_CPU to
    migrated TCP requests

  * disabling SO_INCOMING_CPU if the socket is in a reuseport group

When the counter reaches 0, we can get back to the O(1) selection
algorithm.

The overall changes are negligible for the non-SO_INCOMING_CPU case,
and the only notable thing is that we have to update sk_incomnig_cpu
under reuseport_lock.  Otherwise, the race prevents transitioning to
the O(n) algorithm and results in the wrong socket selection.

 cpu1 (setsockopt)               cpu2 (listen)
+-----------------+             +-------------+

lock_sock(sk1)                  lock_sock(sk2)

reuseport_update_incoming_cpu(sk1, val)
.
|  /* set CPU as 0 */
|- WRITE_ONCE(sk1->incoming_cpu, val)
|
|                               spin_lock_bh(&reuseport_lock)
|                               reuseport_grow(sk2, reuse)
|                               .
|                               |- more_socks_size = reuse->max_socks * 2U;
|                               |- if (more_socks_size > U16_MAX &&
|                               |       reuse->num_closed_socks)
|                               |  .
|                               |  |- RCU_INIT_POINTER(sk1->sk_reuseport_cb, NULL);
|                               |  `- __reuseport_detach_closed_sock(sk1, reuse)
|                               |     .
|                               |     `- reuseport_put_incoming_cpu(sk1, reuse)
|                               |        .
|                               |        |  /* Read shutdown()ed sk1's sk_incoming_cpu
|                               |        |   * without lock_sock().
|                               |        |   */
|                               |        `- if (sk1->sk_incoming_cpu >= 0)
|                               |           .
|                               |           |  /* decrement not-yet-incremented
|                               |           |   * count, which is never incremented.
|                               |           |   */
|                               |           `- __reuseport_put_incoming_cpu(reuse);
|                               |
|                               `- spin_lock_bh(&reuseport_lock)
|
|- spin_lock_bh(&reuseport_lock)
|
|- reuse = rcu_dereference_protected(sk1->sk_reuseport_cb, ...)
|- if (!reuse)
|  .
|  |  /* Cannot increment reuse->incoming_cpu. */
|  `- goto out;
|
`- spin_unlock_bh(&reuseport_lock)

Fixes: e32ea7e7 ("soreuseport: fast reuseport UDP socket selection")
Fixes: c125e80b ("soreuseport: fast reuseport TCP socket selection")
Reported-by: Kazuho Oku <kazuhooku@gmail.com>
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Alex Elder says:

====================
net: ipa: validation cleanup

This series gathers a set of IPA driver cleanups, mostly involving
code that ensures certain things are known to be correct *early*
(either at build or initializatin time), so they can be assumed good
during normal operation.

The first removes three constant symbols, by making a (reasonable)
assumption that a routing table consists of entries for the modem
followed by entries for the AP, with no unused entries between them.

The second removes two checks that are redundant (they verify the
sizes of two memory regions are in range, which will have been done
earlier for all regions).

The third adds some new checks to routing and filter tables that
can be done at "init time" (without requiring any access to IPA
hardware).

The fourth moves a check that routing and filter table addresses can
be encoded within certain IPA immediate commands, so it's performed
earlier; the checks can be done without touching IPA hardware.  The
fifth moves some other command-related checks earlier, for the same
reason.

The sixth removes the definition ipa_table_valid(), because what it
does has become redundant.  Finally, the last patch moves two more
validation calls so they're done very early in the probe process.
This will be required by some upcoming patches, which will record
the size of the routing and filter tables at this time so they're
available for subsequent initialization.
====================

Link: https://lore.kernel.org/r/20221021191340.4187935-1-elder@linaro.orgSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Verify that the sizes of the routing and filter table memory regions
are valid as part of memory initialization, rather than waiting for
table initialization.  The main reason to do this is that upcoming
patches use these memory region sizes to determine the number of
entries in these tables, and we'll want to know these sizes are good
sooner.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

What ipa_table_valid() (and ipa_table_valid_one(), which it calls)
does is ensure that the memory regions that hold routing and filter
tables have reasonable size.  Specifically, it checks that the size
of a region is sufficient (or rather, exactly the right size) to
hold the maximum number of entries supported by the driver.  (There
is an additional check that's erroneous, but in practice it is never
reached.)

Recently ipa_table_mem_valid() was added, which is called by
ipa_table_init().  That function verifies that all table memory
regions are of sufficient size, and requires hashed tables to have
zero size if hashing is not supported.  It only ensures the filter
table is large enough to hold the number of endpoints that support
filtering, but that is adequate.

Therefore everything that ipa_table_valid() does is redundant, so
get rid of it.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Currently, ipa_cmd_data_valid() is called by ipa_mem_config().
Nothing it does requires access to hardware though, so it can be
done during the init phase of IPA driver startup.

Create a new function ipa_cmd_init(), whose purpose is to do early
initialization related to IPA immediate commands.  It will call the
build-time validation function, then will make the two calls made
previously by ipa_cmd_data_valid().  This make ipa_cmd_data_valid()
unnecessary, so get rid of it.

Rename ipa_cmd_header_valid() to be ipa_cmd_header_init_local_valid(),
so its name is clearer about which IPA immediate command it is
associated with.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

We currently verify the table size and offset fit in the immediate
command fields that must encode them in ipa_table_valid_one().  We
can now make this check earlier, in ipa_table_mem_valid().

The non-hashed IPv4 filter and route tables will always exist, and
their sizes will match the IPv6 tables, as well as the hashed tables
(if supported).  So it's sufficient to verify the offset and size of
the IPv4 non-hashed tables fit into these fields.

Rename the function ipa_cmd_table_init_valid(), to reinforce that
it is the TABLE_INIT immediate command fields we're checking.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Add checks in ipa_table_init() to ensure the memory regions defined
for IPA filter and routing tables are valid.

For routing tables, the checks ensure:
  - The non-hashed IPv4 and IPv6 routing tables are defined
  - The non-hashed IPv4 and IPv6 routing tables are the same size
  - The number entries in the non-hashed IPv4 routing table is enough
    to hold the number entries available to the modem, plus at least
    one usable by the AP.

For filter tables, the checks ensure:
  - The non-hashed IPv4 and IPv6 filter tables are defined
  - The non-hashed IPv4 and IPv6 filter tables are the same size
  - The number entries in the non-hashed IPv4 filter table is enough
    to hold the endpoint bitmap, plus an entry for each defined
    endpoint that supports filtering.

In addition, for both routing and filter tables:
  - If hashing isn't supported (IPA v4.2), hashed tables are zero size
  - If hashing *is* supported, all hashed tables are the same size as
    their non-hashed counterparts.

When validating the size of routing tables, require the AP to have
at least one entry (in addition to those used by the modem).
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

There's no need to ensure table memory regions fit within the
IPA-local memory range.  And there's no need to ensure the modem
header memory region is in range either.  These are verified for all
memory regions in ipa_mem_size_valid(), once we have settled on the
size of IPA memory.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

The entries in each IPA routing table are divided between the modem
and the AP.  The modem always gets some number of entries located at
the base of the table; the AP gets all those that follow.

There's no reason to think the modem will use anything different
from the first entries in a routing table, so:
  - Get rid of IPA_ROUTE_MODEM_MIN (just assume it's 0)
  - Get rid of IPA_ROUTE_AP_MIN (just assume it's IPA_ROUTE_MODEM_COUNT)
And finally:
  - Open-code IPA_ROUTE_AP_COUNT and remove its definition
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Amritha Nambiar says:

====================
Extend action skbedit to RX queue mapping

Based on the discussion on
https://lore.kernel.org/netdev/166260012413.81018.8010396115034847972.stgit@anambiarhost.jf.intel.com/ ,
the following series extends skbedit tc action to RX queue mapping.
Currently, skbedit action in tc allows overriding of transmit queue.
Extending this ability of skedit action supports the selection of
receive queue for incoming packets. On the receive side, this action
is supported only in hardware, so the skip_sw flag is enforced.

Enabled ice driver to offload this type of filter into the hardware
for accepting packets to the device's receive queue.
====================

Link: https://lore.kernel.org/r/166633888716.52141.3425659377117969638.stgit@anambiarhost.jf.intel.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Add tc-queue-filters.rst with notes on TC filters for
selecting a set of queues and/or a queue.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

This patch uses TC skbedit queue_mapping action to support
forwarding packets to a device queue. Such filters with action
forward to queue will be the highest priority switch filter in
HW.
Example:
$ tc filter add dev ens4f0 protocol ip ingress flower\
  dst_ip 192.168.1.12 ip_proto tcp dst_port 5001\
  action skbedit queue_mapping 5 skip_sw

The above command adds an ingress filter, incoming packets
qualifying the match will be accepted into queue 5. The queue
number is in decimal format.

Refactored ice_add_tc_flower_adv_fltr() to consolidate code with
action FWD_TO_VSI and FWD_TO QUEUE.
Reviewed-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Reviewed-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Add support for skbedit queue mapping action on receive
side. This is supported only in hardware, so the skip_sw
flag is enforced. This enables offloading filters for
receive queue selection in the hardware using the
skbedit action. Traffic arrives on the Rx queue requested
in the skbedit action parameter. A new tc action flag
TCA_ACT_FLAGS_AT_INGRESS is introduced to identify the
traffic direction the action queue_mapping is requested
on during filter addition. This is used to disallow
offloading the skbedit queue mapping action on transmit
side.

Example:
$tc filter add dev $IFACE ingress protocol ip flower dst_ip $DST_IP\
 action skbedit queue_mapping $rxq_id skip_sw
Reviewed-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Russell King says:

====================
net: sfp: improve high power module implementation

This series aims to improve the power level switching between standard
level 1 and the higher power levels.

The first patch updates the DT binding documentation to include the
minimum and default of 1W, which is the base level that every SFP cage
must support. Hence, it makes sense to document this in the binding.

The second patch enforces a minimum of 1W when parsing the firmware
description, and optimises the code for that case; there's no need to
check for SFF8472 compliance since we will not need to touch the
A2h registers.

Patch 3 validates that the module supports SFF-8472 rev 10.2 before
checking for power level 2 - rev 10.2 is where support for power
levels was introduced, so if the module doesn't support this revision,
it doesn't support power levels. Setting the power level 2 declaration
bit is likely to be spurious.

Patch 4 does the same for power level 3, except this was introduced in
SFF-8472 rev 11.9. The revision code was never updated, so we use the
rev 11.4 to signify this.

Patch 5 cleans up the code - rather than using BIT(0), we now use a
properly named value for the power level select bit.

Patch 6 introduces a read-modify-write helper.

Patch 7 gets rid of the DM7052 hack (which sets a power level
declaration bit but is not compatible with SFF-8472 rev 10.2, and
the module does not implement the A2h I2C address.)

Series tested with my DM7052.

v2: update sff.sfp.yaml with Rob's feedback
====================

Andrew's review tags from v1.

Link: https://lore.kernel.org/r/Y0%2F7dAB8OU3jrbz6@shell.armlinux.org.uk
Link: https://lore.kernel.org/r/Y1K17UtfFopACIi2@shell.armlinux.org.ukSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Since we no longer mis-detect high-power mode with the DM7052 module,
we no longer need the hack in sfp_module_enable_high_power(), and can
now switch this to use sfp_modify_u8().
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Add a helper to modify bits in a single byte in memory space, and use
it when updating the soft tx-disable flag in the module.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Provide a named definition for the power level select bit in the
extended status register, rather than using BIT(0) in the code.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Power level 3 was included in SFF-8472 revision 11.9, but this does
not have a compliance code. Use revision 11.4 as the minimum
compliance level instead.

This should avoid any spurious indication of 2W modules.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Power level 2 was introduced by SFF-8472 revision 10.2. Ignore
the power declaration bit for modules that are not compliant with
at least this revision.

This should remove any spurious indication of 1.5W modules.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Check that the firmware provided maximum power is at least 1W, which
is the minimum power level for any SFP module.

Now that we enforce the minimum of 1W, we can exit early from
sfp_module_parse_power() if the module power is 1W or less.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Add a minimum and default for the maximum-power-milliwatt option;
module power levels were originally up to 1W, so this is the default
and the minimum power level we can have for a functional SFP cage.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Michael Chan says:

====================
bnxt_en: Driver updates

This patchset adds .get_module_eeprom_by_page() support and adds
an NVRAM resize step to allow larger firmware images to be flashed
to older firmware.
====================

Link: https://lore.kernel.org/r/1666334243-23866-1-git-send-email-michael.chan@broadcom.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Resize of the UPDATE entry is required if the image to
be flashed is larger than the available space. Add this step,
otherwise flashing larger firmware images by ethtool or devlink
may fail.
Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Add support for .get_module_eeprom_by_page() callback which
implements generic solution for module`s eeprom access.

v3: Add bnxt_get_module_status() to get a more specific extack error
    string.
    Return -EINVAL from bnxt_get_module_eeprom_by_page() when we
    don't want to fallback to old method.
v2: Simplification suggested by Ido Schimmel

Link: https://lore.kernel.org/netdev/YzVJ%2FvKJugoz15yV@shredder/Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The main changes are PTM timestamp support, CMIS EEPROM support, and
asymmetric CoS queues support.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>